- 14 Nov, 2014 40 commits
-
-
Adel Gadllah authored
commit d7499475 upstream. Yet another device affected by this. Tested-by:
Kevin Fenzi <kevin@scrye.com> Signed-off-by:
Adel Gadllah <adel.gadllah@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Adel Gadllah authored
commit 876af5d4 upstream. Currently this quirk is enabled for the model with the device id 0x0089, it is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904 as well. Signed-off-by:
-
Johan Hovold authored
commit c68929f7 upstream. Enable device-qualifier quirk for Elan Touchscreen, which often fails to handle requests for the device_descriptor. Note that the device sometimes do respond properly with a Request Error (three times as USB core retries), but usually fails to respond at all. When this happens any further descriptor requests also fails, for example: [ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd [ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71 [ 1530.945592] usb 2-7: can't read configurations, error -71 This has been observed repeating for over a minute before eventual successful enumeration. Reported-by:
Drew Von Spreecken <drewvs@gmail.com> Reported-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 2a159389 upstream. Add new quirk for devices that cannot handle requests for the device_qualifier descriptor. A USB-2.0 compliant device must respond to requests for the device_qualifier descriptor (even if it's with a request error), but at least one device is known to misbehave after such a request. Suggested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Torsten Fleischer authored
commit 9680b60e upstream. The call of 'kfree(ci->hw_bank.regmap)' in ci_hdrc_remove() sometimes causes a kernel oops when removing the ci_hdrc module. Since there is no separate memory allocated for the ci->hw_bank.regmap array, there is no need to free it. Signed-off-by:
Torsten Fleischer <to-fleischer@t-online.de> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
David Cohen authored
commit c0d31b3c upstream. The commit '2e4c7553 usb: gadget: f_fs: add aio support' broke the quirk implemented to align buffer size to maxpacketsize on out endpoint. As result, functionfs does not work on Intel platforms using dwc3 driver (i.e. Bay Trail and Merrifield). This patch fixes the issue. This code is based on a previous Qiuxu's patch. Fixes: 2e4c7553 (usb: gadget: f_fs: add aio support) Signed-off-by:
David Cohen <david.a.cohen@linux.intel.com> Signed-off-by:
Qiuxu Zhuo <qiuxu.zhuo@intel.com> Acked-by:
Michal Nazarewicz <mina86@mina86.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Robert Baldyga authored
commit a3058a5d upstream. During FunctionFS bind, ffs_data_get() function was called twice (in functionfs_bind() and in ffs_do_functionfs_bind()), while on unbind ffs_data_put() was called once (in functionfs_unbind() function). In result refcount never reached value 0, and ffs memory resources has been never released. Since ffs_data_get() call in ffs_do_functionfs_bind() is redundant and not neccessary, we remove it to have equal number of gets ans puts, and free allocated memory after refcount reach 0. Fixes: 5920cda6 (usb: gadget: FunctionFS: convert to new function interface with backward compatibility) Signed-off-by:
Robert Baldyga <r.baldyga@samsung.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 53185b3a upstream. Commit 468bcc2a ("usb: musb: dsps: kill OTG timer on suspend") stopped the timer in suspend path but forgot the re-enable it in the resume path. This patch fixes the behaviour. Fixes 468bcc2a "usb: musb: dsps: kill OTG timer on suspend" Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Thomas Gleixner authored
commit d2e6d62c upstream. commit c58d80f5 ("usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq") fixed hrtimer scheduling bug. There is one left which does not trigger that often. The following scenario is still possible: lock(&x->lock); hrtimer_start(&x->t); unlock(&x->lock); expires: t->function(); lock(&x->lock); lock(&x->lock); if (!hrtimer_queued(&x->t)) hrtimer_start(&x->t); unlock(&x->lock); if (!list_empty(x->early_tx_list)) ret = HRTIMER_RESTART; -> hrtimer_forward_now(...) } else ret = HRTIMER_NORESTART; unlock(&x->lock); and the timer callback returns HRTIMER_RESTART for an armed timer. This is wrong and we run into the BUG_ON() in __run_hrtimer(). This can happens on SMP or PREEMPT-RT. The patch fixes the problem by only starting the timer if the timer is not yet queued. Reported-by:
Torben Hohn <torbenh@linutronix.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> [bigeasy: collected information and created a patch + description based on it] Signed-off-by:
-
Hans de Goede authored
commit aee0ce3a upstream. These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
commit d1d95482 upstream. These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Signed-off-by:
-
Hans de Goede authored
commit 673029fe upstream. Just like some Seagate enclosures, these devices do not seem to grok ata pass through commands. Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 2b9375b9 upstream. If PM_RUNTIME is enabled, it is easy to trigger the following backtrace on pxa2xx hosts: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8() Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104 [<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14) [<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c) [<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24) [<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8) [<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34) [<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54) [<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74) [<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8) [<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208) [<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0) [<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8) [<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc) [<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc) [<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4) [<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec) [<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24) ---[ end trace 46524156d8faa4f6 ]--- This happens because suspend function tries to disable a clock that is already disabled by runtime_suspend callback. Add if (!pm_runtime_suspended()) checks to suspend/resume path. Fixes: 7d94a505 (spi/pxa2xx: add support for runtime PM) Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Reported-by:
Andrea Adami <andrea.adami@gmail.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Alexander Stein authored
commit 5cc7b047 upstream. There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the lower 2 bits of the chip select to select a CTAR register. SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values if the chip selects 4/5 are used. For those chip selects SPI_CTAR even calculated offsets of non-existing registers. Signed-off-by:
Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by:
-
Ray Jui authored
commit 3ffa6158 upstream. When mapped RX DMA entries are unmapped in an error condition when DMA is firstly configured in the driver, the number of TX DMA entries was passed in, which is incorrect Signed-off-by:
Ray Jui <rjui@broadcom.com> Signed-off-by:
-
Jack Pham authored
commit 1200a82a upstream. On ISOC endpoints the last trb_pool entry used as a LINK TRB is not getting zeroed out correctly due to memset being called incorrectly and in the wrong place. If pool allocated from DMA was not zero-initialized to begin with this will result in the size and ctrl values being random garbage. Call memset correctly after assignment of the trb_link pointer. Fixes: f6bafc6a ("usb: dwc3: convert TRBs into bitshifts") Signed-off-by:
Jack Pham <jackp@codeaurora.org> Signed-off-by:
-
Roger Quadros authored
commit b01ff5cb upstream. This reverts commit 02dae36a. That commit is bogus in two ways: 1) There's no way dwc3-omap's ->suspend() can cause any effect on xhci's ->suspend(). Linux device driver model guarantees that a parent's ->suspend() will only be called after all children are suspended. dwc3-omap is the parent of the parent of xhci. 2) When implementing Deep Sleep states where context is lost, USBOTGSS_IRQ0 register, well, looses context so we _must_ rewrite it otherwise core IRQs will never be reenabled and USB will appear to be dead. Fixes: 02dae36a (usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete) Cc: George Cherian <george.cherian@ti.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Cyril Brulebois authored
commit 664d6a79 upstream. 0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle References: https://bugs.debian.org/766802Reported-by:
Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by:
Cyril Brulebois <kibi@debian.org> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Canek Peláez Valdés authored
commit ac0372ab upstream. Signed-off-by:
Canek Peláez Valdés <canek@ciencias.unam.mx> Signed-off-by:
-
Dan Williams authored
commit 012eee15 upstream. Port layout: 0: QCDM/DIAG 1: NMEA 2: AT 3: AT/PPP Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Daniele Palmas authored
commit 2d0eb862 upstream. Add VID/PID for Telit LE910 modem. Interfaces description is almost the same than LE920, except that the qmi interface is number 2 (instead than 5). Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Oussama Ghorbel authored
commit f20531a9 upstream. The USB OTG port does not work since v3.16 on omap platform. This is a regression introduced by the commit eb82a3d8 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove). This because the call to pm_runtime_enable() function is moved after the call to devm_phy_create() function, which has side effect since later in the subsequent calls of devm_phy_create() there is a check with pm_runtime_enabled() to configure few things. Fixes: eb82a3d8Signed-off-by:
Oussama Ghorbel <ghorbel@pivasoftware.com> Tested-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Johan Hovold authored
commit 2a8cdfde upstream. Add new quirk for devices that cannot handle control-line state requests. Note that we currently send these requests to all devices, regardless of whether they claim to support it, but that errors are only logged if support is claimed. Since commit 0943d8ea ("USB: cdc-acm: use tty-port dtr_rts"), which only changed the timings for these requests slightly, this has been reported to cause occasional firmware crashes on Simtec Electronics Entropy Key devices after re-enumeration. Enable the quirk for this device. Reported-by:
Nix <nix@esperi.org.uk> Tested-by:
-
Johan Hovold authored
commit 4473d054 upstream. Make sure to only raise DTR on transitions from B0 in set_termios. Also allow set_termios to be called from open with a termios_old of NULL. Note that DTR will not be raised prematurely in this case. Signed-off-by:
-
Johan Hovold authored
commit cf84a691 upstream. Add device-id entry for GW Instek AFG-2225, which has a byte swapped bInterfaceSubClass (0x20). Reported-by:
Karl Palsson <karlp@tweak.net.au> Signed-off-by:
-
Perry Hung authored
commit 7f2719f0 upstream. An official recent Windows driver from FTDI detects counterfeit devices and reprograms the internal EEPROM containing the USB PID to 0, effectively bricking the device. Add support for this VID/PID pair to correctly bind the driver on these devices. See: http://hackaday.com/2014/10/22/watch-that-windows-update-ftdi-drivers-are-killing-fake-chips/Signed-off-by:
Perry Hung <iperry@gmail.com> Acked-by:
-
Frans Klaver authored
commit edd74ffa upstream. Add new IDs for the Xsens Awinda Station and Awinda Dongle. While at it, order the definitions by PID and add a logical separation between devices using Xsens' VID and those using FTDI's VID. Signed-off-by:
Frans Klaver <frans.klaver@xsens.com> Signed-off-by:
-
Nathaniel Ting authored
commit 35cc83ea upstream. Enable Silicon Labs Ember VID chips to enumerate with the cp210x usb serial driver. EM358x devices operating with the Ember Z-Net 5.1.2 stack may now connect to host PCs over a USB serial link. Signed-off-by:
Nathaniel Ting <nathaniel.ting@silabs.com> Signed-off-by:
-
Peter Hurley authored
commit 547039ec upstream. uart_get_baud_rate() will return baud == 0 if the max rate is set to the "magic" 38400 rate and the SPD_* flags are also specified. On the first iteration, if the current baud rate is higher than the max, the baud rate is clamped at the max (which in the degenerate case is 38400). On the second iteration, the now-"magic" 38400 baud rate selects the possibly higher alternate baud rate indicated by the SPD_* flag. Since only two loop iterations are performed, the loop is exited, a kernel WARNING is generated and a baud rate of 0 is returned. Reproducible with: setserial /dev/ttyS0 spd_hi base_baud 38400 Only perform the "magic" 38400 -> SPD_* baud transform on the first loop iteration, which prevents the degenerate case from recognizing the clamped baud rate as the "magic" 38400 value. Reported-by:
Robert Święcki <robert@swiecki.net> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Stephen Boyd authored
commit 8b374399 upstream. Frank reports that after continuing in kgdb the RX stale event doesn't occur until after the RX fifo is filled up with exactly the amount of characters programmed for the RX watermark (in this case it's 48). To read a single character from the uartdm hardware we force a stale event so that any characters in the RX packing buffer are flushed into the RX fifo immediately instead of waiting for a stale timeout or for the fifo to fill. Forcing that stale event asserts the stale interrupt but we never clear that interrupt via UART_CR_CMD_RESET_STALE_INT in the polling functions. So when kgdb continues the stale interrupt is left pending in the hardware and we don't timeout with a stale event, like we usually would if a user typed one character on the console, until the reset stale interrupt and stale event commands are sent. Frank could get things working again by running handle_rx_dm(). By putting enough characters into the fifo he could trigger a watermark interrupt, and thus cause handle_rx_dm() to run finally resetting the stale interrupt and enabling the stale event so that single characters would cause timeouts again. The fix is to just do what the interrupt routine was doing all along and clear the stale interrupt and enable the event again. Doing this also smooths over any differences in the fifo behavior between v1.3 and v1.4 hardware allowing us to skip forcing the uart into single character mode. Reviewed-by:
Frank Rowand <frank.rowand@sonymobile.com> Tested-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit b598aacc upstream. "raw" is a property of a channel, but should not be part of the name of channel. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit 79fa64eb upstream. We should check if a channel is enabled, not if no channels are enabled. Fixes: 550268ca ("staging:iio: scrap scan_count and ensure all drivers use active_scan_mask") Signed-off-by:
-
Lars-Peter Clausen authored
commit e1055473 upstream. In older versions of the IIO framework it was possible to pass a completely different set of channels to iio_buffer_register() as the one that is assigned to the IIO device. Commit 959d2952 ("staging:iio: make iio_sw_buffer_preenable much more general.") introduced a restriction that requires that the set of channels that is passed to iio_buffer_register() is a subset of the channels assigned to the IIO device as the IIO core will use the list of channels that is assigned to the device to lookup a channel by scan index in iio_compute_scan_bytes(). If it can not find the channel the function will crash. This patch fixes the issue by making sure that the same set of channels is assigned to the IIO device and passed to iio_buffer_register(). Note that we need to remove the IIO_CHAN_INFO_RAW and IIO_CHAN_INFO_SCALE info attributes from the channels since we don't actually want those to be registered. Fixes the following crash: Unable to handle kernel NULL pointer dereference at virtual address 00000016 pgd = d2094000 [00000016] *pgd=16e39831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 1695 Comm: bash Not tainted 3.17.0-06329-g29461ee #9686 task: d7768040 ti: d5bd4000 task.ti: d5bd4000 PC is at iio_compute_scan_bytes+0x38/0xc0 LR is at iio_compute_scan_bytes+0x34/0xc0 pc : [<c0316de8>] lr : [<c0316de4>] psr: 60070013 sp : d5bd5ec0 ip : 00000000 fp : 00000000 r10: d769f934 r9 : 00000000 r8 : 00000001 r7 : 00000000 r6 : c8fc6240 r5 : d769f800 r4 : 00000000 r3 : d769f800 r2 : 00000000 r1 : ffffffff r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 18c5387d Table: 1209404a DAC: 00000015 Process bash (pid: 1695, stack limit = 0xd5bd4240) Stack: (0xd5bd5ec0 to 0xd5bd6000) 5ec0: d769f800 d7435640 c8fc6240 d769f984 00000000 c03175a4 d7435690 d7435640 5ee0: d769f990 00000002 00000000 d769f800 d5bd4000 00000000 000b43a8 c03177f4 5f00: d769f810 0162b8c8 00000002 c8fc7e00 d77f1d08 d77f1da8 c8fc7e00 c01faf1c 5f20: 00000002 c010694c c010690c d5bd5f88 00000002 c8fc6840 c8fc684c c0105e08 5f40: 00000000 00000000 d20d1580 00000002 000af408 d5bd5f88 c000de84 c00b76d4 5f60: d20d1580 000af408 00000002 d20d1580 d20d1580 00000002 000af408 c000de84 5f80: 00000000 c00b7a44 00000000 00000000 00000002 b6ebea78 00000002 000af408 5fa0: 00000004 c000dd00 b6ebea78 00000002 00000001 000af408 00000002 00000000 5fc0: b6ebea78 00000002 000af408 00000004 bee96a4c 000a6094 00000000 000b43a8 5fe0: 00000000 bee969cc b6e2eb77 b6e6525c 40070010 00000001 00000000 00000000 [<c0316de8>] (iio_compute_scan_bytes) from [<c03175a4>] (__iio_update_buffers+0x248/0x438) [<c03175a4>] (__iio_update_buffers) from [<c03177f4>] (iio_buffer_store_enable+0x60/0x7c) [<c03177f4>] (iio_buffer_store_enable) from [<c01faf1c>] (dev_attr_store+0x18/0x24) [<c01faf1c>] (dev_attr_store) from [<c010694c>] (sysfs_kf_write+0x40/0x4c) [<c010694c>] (sysfs_kf_write) from [<c0105e08>] (kernfs_fop_write+0x110/0x154) [<c0105e08>] (kernfs_fop_write) from [<c00b76d4>] (vfs_write+0xbc/0x170) [<c00b76d4>] (vfs_write) from [<c00b7a44>] (SyS_write+0x40/0x78) [<c00b7a44>] (SyS_write) from [<c000dd00>] (ret_fast_syscall+0x0/0x30) Fixes: 959d2952 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by:
-
George McCollister authored
commit f73cde60 upstream. Signed-off-by:
George McCollister <george.mccollister@gmail.com> Acked-by:
Hartmut Knaack <knaack.h@gmx.de> Signed-off-by:
-
Lars-Peter Clausen authored
commit 6822ee34 upstream. "raw" is the name of a channel property, but should not be part of the channel name itself. Signed-off-by:
-
Lars-Peter Clausen authored
commit 824269c5 upstream. In older versions of the IIO framework it was possible to pass a completely different set of channels to iio_buffer_register() as the one that is assigned to the IIO device. Commit 959d2952 ("staging:iio: make iio_sw_buffer_preenable much more general.") introduced a restriction that requires that the set of channels that is passed to iio_buffer_register() is a subset of the channels assigned to the IIO device as the IIO core will use the list of channels that is assigned to the device to lookup a channel by scan index in iio_compute_scan_bytes(). If it can not find the channel the function will crash. This patch fixes the issue by making sure that the same set of channels is assigned to the IIO device and passed to iio_buffer_register(). Fixes the follow NULL pointer derefernce kernel crash: Unable to handle kernel NULL pointer dereference at virtual address 00000016 pgd = d53d0000 [00000016] *pgd=1534e831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 1626 Comm: bash Not tainted 3.15.0-19969-g2a180eb-dirty #9545 task: d6c124c0 ti: d539a000 task.ti: d539a000 PC is at iio_compute_scan_bytes+0x34/0xa8 LR is at iio_compute_scan_bytes+0x34/0xa8 pc : [<c03052e4>] lr : [<c03052e4>] psr: 60070013 sp : d539beb8 ip : 00000001 fp : 00000000 r10: 00000002 r9 : 00000000 r8 : 00000001 r7 : 00000000 r6 : d6dc8800 r5 : d7571000 r4 : 00000002 r3 : d7571000 r2 : 00000044 r1 : 00000001 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 18c5387d Table: 153d004a DAC: 00000015 Process bash (pid: 1626, stack limit = 0xd539a240) Stack: (0xd539beb8 to 0xd539c000) bea0: c02fc0e4 d7571000 bec0: d76c1640 d6dc8800 d757117c 00000000 d757112c c0305b04 d76c1690 d76c1640 bee0: d7571188 00000002 00000000 d7571000 d539a000 00000000 000dd1c8 c0305d54 bf00: d7571010 0160b868 00000002 c69d3900 d7573278 d7573308 c69d3900 c01ece90 bf20: 00000002 c0103fac c0103f6c d539bf88 00000002 c69d3b00 c69d3b0c c0103468 bf40: 00000000 00000000 d7694a00 00000002 000af408 d539bf88 c000dd84 c00b2f94 bf60: d7694a00 000af408 00000002 d7694a00 d7694a00 00000002 000af408 c000dd84 bf80: 00000000 c00b32d0 00000000 00000000 00000002 b6f1aa78 00000002 000af408 bfa0: 00000004 c000dc00 b6f1aa78 00000002 00000001 000af408 00000002 00000000 bfc0: b6f1aa78 00000002 000af408 00000004 be806a4c 000a6094 00000000 000dd1c8 bfe0: 00000000 be8069cc b6e8ab77 b6ec125c 40070010 00000001 22940489 154a5007 [<c03052e4>] (iio_compute_scan_bytes) from [<c0305b04>] (__iio_update_buffers+0x248/0x438) [<c0305b04>] (__iio_update_buffers) from [<c0305d54>] (iio_buffer_store_enable+0x60/0x7c) [<c0305d54>] (iio_buffer_store_enable) from [<c01ece90>] (dev_attr_store+0x18/0x24) [<c01ece90>] (dev_attr_store) from [<c0103fac>] (sysfs_kf_write+0x40/0x4c) [<c0103fac>] (sysfs_kf_write) from [<c0103468>] (kernfs_fop_write+0x110/0x154) [<c0103468>] (kernfs_fop_write) from [<c00b2f94>] (vfs_write+0xd0/0x160) [<c00b2f94>] (vfs_write) from [<c00b32d0>] (SyS_write+0x40/0x78) [<c00b32d0>] (SyS_write) from [<c000dc00>] (ret_fast_syscall+0x0/0x30) Code: ea00000e e1a01008 e1a00005 ebfff6fc (e5d0a016) Fixes: 959d2952 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by:
-
Fabio Estevam authored
commit 75d7ed3b upstream. We should disable lradc->clk in the case of errors in the probe function. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Robin van der Gracht authored
commit 4250c90b upstream. Use byte_for_channel as iterator to properly initialize the buffer. Signed-off-by:
Robin van der Gracht <robin@protonic.nl> Acked-by:
Denis Ciocca <denis.ciocca@st.com> Signed-off-by:
-
Michal Hocko authored
commit 5695be14 upstream. PM freezer relies on having all tasks frozen by the time devices are getting frozen so that no task will touch them while they are getting frozen. But OOM killer is allowed to kill an already frozen task in order to handle OOM situtation. In order to protect from late wake ups OOM killer is disabled after all tasks are frozen. This, however, still keeps a window open when a killed task didn't manage to die by the time freeze_processes finishes. Reduce the race window by checking all tasks after OOM killer has been disabled. This is still not race free completely unfortunately because oom_killer_disable cannot stop an already ongoing OOM killer so a task might still wake up from the fridge and get killed without freeze_processes noticing. Full synchronization of OOM and freezer is, however, too heavy weight for this highly unlikely case. Introduce and check oom_kills counter which gets incremented early when the allocator enters __alloc_pages_may_oom path and only check all the tasks if the counter changes during the freezing attempt. The counter is updated so early to reduce the race window since allocator checked oom_killer_disabled which is set by PM-freezing code. A false positive will push the PM-freezer into a slow path but that is not a big deal. Changes since v1 - push the re-check loop out of freeze_processes into check_frozen_processes and invert the condition to make the code more readable as per Rafael Fixes: f660daac (oom: thaw threads if oom killed thread is frozen before deferring) Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Lv Zheng authored
commit 79149001 upstream. It is reported that Samsung laptops that need to poll events are broken by the following commit: Commit 3afcf2ec Subject: ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set The behaviors of the 2 vendor firmwares are conflict: 1. Acer: OSPM shouldn't issue QR_EC unless SCI_EVT is set, firmware automatically sets SCI_EVT as long as there is event queued up. 2. Samsung: OSPM should issue QR_EC whatever SCI_EVT is set, firmware returns 0 when there is no event queued up. This patch is a quick fix to distinguish the behaviors to make Acer behavior only effective for Acer EC firmware so that the breakages on Samsung EC firmware can be avoided. Fixes: 3afcf2ec (ACPI / EC: Add support to disallow QR_EC to be issued ...) Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161Reported-and-tested-by:
Ortwin Glück <odi@odi.ch> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> [ rjw : Subject ] Signed-off-by:
-
