- 18 Feb, 2019 40 commits
-
-
Jagan Teki authored
CSI block in Allwinner A64 has similar features as like in H3, but the default CSI_SCLK rate cannot work properly to drive the connected sensor interface. The tested mod cock rate is 300 MHz and BSP vfe media driver is also using the same rate. Unfortunately there is no valid information about clock rate in manual or any other sources except the BSP driver. so more faith on BSP code, because same has tested in mainline. So, add support for A64 CSI block by setting updated mod clock rate. Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Jagan Teki authored
Allwinner A64 CSI is a single channel time-multiplexed BT.656 protocol interface. Add separate compatible string for A64 since it require explicit change in sun6i_csi driver to update default CSI_SCLK rate. Signed-off-by:
Rob Herring <robh@kernel.org> Acked-by:
-
Hans Verkuil authored
The extended-controls.rst file had become too big. Split it up: each control class reference gets its own rst file, and this file just describes the Extended Control API. Each control class reference is also moved up one level into the table of contents to make it easier to find e.g. the codec control reference. Finally I rearranged the order so that all camera-related control classes are grouped together, ditto for codec/jpeg and fm-rx/tx. The ext-ctrls-codec.rst is still pretty big and it is a candidate to split up further in the future, possibly per codec. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in dvb_demux_poll(), dvb_dvr_poll() and dvb_ca_en50221_io_poll(). Fix this, otherwise epoll() can timeout when it shouldn't. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in videobuf_poll_stream(). Fix this, otherwise epoll() would timeout when it shouldn't. Signed-off-by:
-
Hans Verkuil authored
The v4l2_m2m_poll function didn't check whether q->error was set for either of the two queues. Add support for this. Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in v4l2_m2m_poll(). Fix this, otherwise epoll() would timeout when it shouldn't. Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in v4l2_ctrl_poll(). Fix this, otherwise epoll() would timeout when it shouldn't. Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in vb2_core_poll() and vb2_poll(). Fix this, otherwise epoll() would timeout when it shouldn't. Signed-off-by:
Yi Qingliang <niqingliang2003@gmail.com> Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in media_request_poll(). Fix this, otherwise epoll() would timeout when it shouldn't. Signed-off-by:
-
Hans Verkuil authored
The epoll function expects that whenever the poll file op is called, the poll_wait function is also called. That didn't always happen in cec_poll(). Fix this, otherwise epoll() would timeout when it shouldn't. Signed-off-by:
-
Hans Verkuil authored
If a stream is stopped, or if a USERPTR/DMABUF buffer is queued backed by a different user address or dmabuf fd, then the timestamp should be skipped by vb2_find_timestamp since the memory it refers to is no longer valid. So keep track of a 'copied_timestamp' state: it is set when the timestamp is copied from an output to a capture buffer, and is cleared when it is no longer valid. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
-
Hans Verkuil authored
The bool type is not recommended for use in structs, so replace these by bitfields. Signed-off-by:
-
Vivek Kasireddy authored
Buffers generated with YUV32 format seems to be incorrect, hence use VUYA32 instead. Changes from v1: Add both formats VUYA32 and VUYX32 but associate only VUYX32 to the output queue as the alpha channel of buffers is ignored on this queue. Signed-off-by:
Vivek Kasireddy <vivek.kasireddy@intel.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Vivek Kasireddy authored
Enable vivid to make use of the following formats: V4L2_PIX_FMT_AYUV32 V4L2_PIX_FMT_XYUV32 V4L2_PIX_FMT_VUYA32 V4L2_PIX_FMT_VUYX32 Signed-off-by:
-
Vivek Kasireddy authored
Add support for the following formats to tpg: V4L2_PIX_FMT_AYUV32 V4L2_PIX_FMT_XYUV32 V4L2_PIX_FMT_VUYA32 V4L2_PIX_FMT_VUYX32 Changes from v1: Remove the duplicate case value Signed-off-by:
-
Vivek Kasireddy authored
The formats added in this patch include: V4L2_PIX_FMT_AYUV32 V4L2_PIX_FMT_XYUV32 V4L2_PIX_FMT_VUYA32 V4L2_PIX_FMT_VUYX32 These formats enable the trasmission of alpha channel data to other drivers and userspace applications in addition to YUV data. For example, buffers generated by drivers in one of these formats can be used by the Weston compositor to display as a texture or flipped directly onto the overlay planes with the help of a DRM driver. Signed-off-by:
-
Cody P Schafer authored
Without this, we get failures like this when the kernel attempts to initialize a cx231xx device: [16046.153653] cx231xx 3-1.2:1.1: New device Hauppauge Hauppauge Device @ 480 Mbps (2040:c200) with 6 interfaces [16046.153900] cx231xx 3-1.2:1.1: can't change interface 3 alt no. to 3: Max. Pkt size = 0 [16046.153907] cx231xx 3-1.2:1.1: Identified as Hauppauge USB Live 2 (card=9) [16046.154350] i2c i2c-11: Added multiplexed i2c bus 13 [16046.154379] i2c i2c-11: Added multiplexed i2c bus 14 [16046.267194] cx25840 10-0044: cx23102 A/V decoder found @ 0x88 (cx231xx #0-0) [16048.424551] cx25840 10-0044: loaded v4l-cx231xx-avcore-01.fw firmware (16382 bytes) [16048.463224] cx231xx 3-1.2:1.1: v4l2 driver version 0.0.3 [16048.567878] cx231xx 3-1.2:1.1: Registered video device video2 [v4l2] [16048.568001] cx231xx 3-1.2:1.1: Registered VBI device vbi0 [16048.568419] cx231xx 3-1.2:1.1: audio EndPoint Addr 0x83, Alternate settings: 3 [16048.568425] cx231xx 3-1.2:1.1: video EndPoint Addr 0x84, Alternate settings: 5 [16048.568431] cx231xx 3-1.2:1.1: VBI EndPoint Addr 0x85, Alternate settings: 2 [16048.568436] cx231xx 3-1.2:1.1: sliced CC EndPoint Addr 0x86, Alternate settings: 2 [16048.568448] usb 3-1.2: couldn't get decoder output pad for V4L I/O [16048.568453] cx231xx 3-1.2:1.1: V4L2 device vbi0 deregistered [16048.568579] cx231xx 3-1.2:1.1: V4L2 device video2 deregistered [16048.569001] cx231xx: probe of 3-1.2:1.1 failed with error -22 Likely a regession since Commit 9d6d20e6 ("media: v4l2-mc: switch it to use the new approach to setup pipelines") (v4.19-rc1-100-g9d6d20e6), which introduced the use of PAD_SIGNAL_DV within v4l2_mc_create_media_graph(). This also modifies cx25840 to remove the VBI pad, matching the action taken in Commit 092a3787 ("media: v4l2: remove VBI output pad"). Fixes: 9d6d20e6 ("media: v4l2-mc: switch it to use the new approach to setup pipelines") Cc: stable@vger.kernel.org Signed-off-by:
Cody P Schafer <dev@codyps.com> Tested-by:
-
Colin Ian King authored
There is a spelling mistake in a fmdbg debug message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Hans Verkuil authored
media_device_cleanup() wasn't called, which caused a small memory leak. Signed-off-by:
-
Hans Verkuil authored
When the media device registration fails, don't call media_device_unregister since the device was never actually registered. When removing the module also call media_device_cleanup() to avoid a memory leak. Signed-off-by:
-
Sakari Ailus authored
This patch makes the SoC camera framework as well as effectively the few remaining sensor drivers depend on BROKEN, rendering it uncompileable without changes in Kconfig. The purpose is to leave the code around if someone wishes to convert the drivers to the modern day V4L2 sub-device framework without having to go to see development history in git. Signed-off-by:
-
Sakari Ailus authored
Move the mt9t031 driver to the soc_camera directory in the media staging tree. Signed-off-by:
-
Sakari Ailus authored
Move the imx074 driver to the soc_camera directory in the media staging tree. Signed-off-by:
-
Sakari Ailus authored
The SoC camera framework has no functional drivers left, something that has not changed for years. Move the leftovers to the staging tree. Signed-off-by:
-
Sakari Ailus authored
There is a V4L2 sub-device sensor driver for the rj45n1. As there is already another driver, remove the SoC camera one. Signed-off-by:
-
Sakari Ailus authored
There is a V4L2 sub-device sensor driver for the mt9m001. There is already a non-soc_camera driver. So, remove the SoC camera one. Signed-off-by:
-
Yong Zhi authored
This addresses the below TODO item, no function related changes: - Prefix imgu for all public APIs, i.e. change ipu3_v4l2_register() to imgu_v4l2_register(). (Sakari) The changes were obtained by applying the following perl script to driver code under drivers/staging/media/ipu3/. perl -pi.back -e 's/ipu3_(?!uapi)/imgu_/g;' Signed-off-by:
Yong Zhi <yong.zhi@intel.com> Signed-off-by:
-
Loic Poulain authored
According to the ov5640 specification (2.7 power up sequence), host can access the sensor's registers 20ms after reset. Trying to access them before leads to undefined behavior and result in sporadic initialization errors. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Jagan Teki authored
The ov5640_try_frame_interval operation updates the FPS as per user input based on default ov5640_frame_rate, OV5640_30_FPS which is failed to update when user trigger 15fps. So, initialize the default ov5640_frame_rate to OV5640_15_FPS so-that it can satisfy to update all fps. Fixes: 5a3ad937 ("media: ov5640: Make the return rate type more explicit") Signed-off-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Chen-Yu Tsai authored
The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3. The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data. As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK. [Sakari Ailus: Align OV5640_REG_JPG_MODE_SELECT register naming.] Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Chen-Yu Tsai authored
When compression is turned on, the on-bus data is framed according to the compression mode, and the height and width set in VFIFO_VSIZE and VFIFO_HSIZE. If these are not updated correctly, the sensor will send data framed in a manner unexpected by the capture interface, such as having more bytes per line than expected, and having the extra data dropped. This ultimately results in corrupted data. Set the two values when the media bus is configured for JPEG data, meaning the sensor would be in JPEG mode. Signed-off-by:
-
Chen-Yu Tsai authored
The OV5640 driver currently supports a static color bar pattern with a small vertical gamma gradient. The hardware also supports a color square pattern, as well as having a rolling bar for dynamic sequences. Add three more test patterns: - color bars with a rolling bar (but without the gamma gradient) - static color squares - color squares with a rolling bar Signed-off-by:
-
Chen-Yu Tsai authored
The transparent feature for test patterns blends the test pattern with an actual captured image. This makes the result non-static, subject to changes in the sensor's field of view. Test patterns should be predictable and deterministic, even if they are dynamic patterns. Disable the transparent feature of the test pattern. Signed-off-by:
-
Chen-Yu Tsai authored
The OV5640 can generate many types of test patterns, some with additional modifiers, such as a rolling bar, or gamma gradients. Add the bit definitions for all bits in the test pattern register, and use them to compose the values to be written to the register. Signed-off-by:
-
Chen-Yu Tsai authored
The OV5640 has many options for generating test patterns. Unfortunately there is only one V4L2 control for it. Thus the driver would need to list some or all combinations. Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern function that programs the hardware. This would allow us to add a matching list of values to program into the hardware, while keeping the two lists together for ease of maintenance. Signed-off-by:
-
Kieran Bingham authored
The ADV748X_PAGE_WAIT is a fake page to insert arbitrary delays in the register tables. Its only usage was removed, so we can remove the handling and simplify the code. Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Kieran Bingham authored
The ADV748x is currently reset by writting a small table of registers to the device. The table lacks documentation and contains magic values to perform the actions, including using a fake register address to introduce a delay loop. Remove the table, and convert to code, documenting the purpose of the specific writes along the way. Signed-off-by:
-
Jacopo Mondi authored
When the adv748x driver is informed about a link being created from HDMI or AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make sure to implement proper routing management at link setup time, to route the selected video stream to the desired TX output. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by:
-
Jacopo Mondi authored
Both the AFE and HDMI s_stream routines (adv748x_afe_s_stream() and adv748x_hdmi_s_stream()) have to enable the CSI-2 TX they are streaming video data to. With the introduction of dynamic routing between HDMI and AFE entities to TXA, the video stream sink needs to be set at run time, and not statically selected as the s_stream functions are currently doing. To fix this, store a reference to the active CSI-2 TX sink for both HDMI and AFE sources, and operate on it when starting/stopping the stream. Reviewed-by:
-
