- 09 Apr, 2021 3 commits
-
-
Paolo Abeni authored
napi_disable() is subject to an hangup, when the threaded mode is enabled and the napi is under heavy traffic. If the relevant napi has been scheduled and the napi_disable() kicks in before the next napi_threaded_wait() completes - so that the latter quits due to the napi_disable_pending() condition, the existing code leaves the NAPI_STATE_SCHED bit set and the napi_disable() loop waiting for such bit will hang. This patch addresses the issue by dropping the NAPI_STATE_DISABLE bit test in napi_thread_wait(). The later napi_threaded_poll() iteration will take care of clearing the NAPI_STATE_SCHED. This also addresses a related problem reported by Jakub: before this patch a napi_disable()/napi_enable() pair killed the napi thread, effectively disabling the threaded mode. On the patched kernel napi_disable() simply stops scheduling the relevant thread. v1 -> v2: - let the main napi_thread_poll() loop clear the SCHED bit Reported-by:
Jakub Kicinski <kuba@kernel.org> Fixes: 29863d41 ("net: implement threaded-able napi poll loop support") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/883923fa22745a9589e8610962b7dc59df09fb1f.1617981844.git.pabeni@redhat.comSigned-off-by:
-
Salil Mehta authored
Some trivial spelling mistakes which caught my eye during the review of the code. Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Link: https://lore.kernel.org/r/20210409074223.32480-1-salil.mehta@huawei.comSigned-off-by:
-
Sven Van Asbroeck authored
The ethernet frame length is calculated incorrectly. Depending on the value of RX_HEAD_PADDING, this may result in ethernet frames that are too short (cut off at the end), or too long (garbage added to the end). Fix by calculating the ethernet frame length correctly. For added clarity, use the ETH_FCS_LEN constant in the calculation. Many thanks to Heiner Kallweit for suggesting this solution. Suggested-by:
Heiner Kallweit <hkallweit1@gmail.com> Fixes: 3e21a10f ("lan743x: trim all 4 bytes of the FCS; not just 2") Link: https://lore.kernel.org/lkml/20210408172353.21143-1-TheSven73@gmail.com/Signed-off-by:
Sven Van Asbroeck <thesven73@gmail.com> Reviewed-by:
George McCollister <george.mccollister@gmail.com> Tested-by:
-
- 08 Apr, 2021 30 commits
-
-
Muhammad Usama Anjum authored
nlh is being checked for validtity two times when it is dereferenced in this function. Check for validity again when updating the flags through nlh pointer to make the dereferencing safe. CC: <stable@vger.kernel.org> Addresses-Coverity: ("NULL pointer dereference") Signed-off-by:Muhammad Usama Anjum <musamaanjum@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Martin Blumenstingl says: ==================== lantiq: GSWIP: two more fixes after my last patch got accepted and is now in net as commit 3e6fdeb2 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock") [0] some more people from the OpenWrt community (many thanks to everyone involved) helped test the GSWIP driver: [1] It turns out that the previous fix does not work for all boards. There's no regression, but it doesn't fix as many problems as I thought. This is why two more fixes are needed: - the first one solves many (four known but probably there are a few extra hidden ones) reported bugs with the GSWIP where no traffic would flow. Not all circumstances are fully understood but testing shows that switching away from PHY auto polling solves all of them - while investigating the different problems which are addressed by the first patch some small issues with the existing code were found. These are addressed by the second patch Changes since v1 at [0]: - Don't configure the link parameters in gswip_phylink_mac_config (as we're using the "modern" way in gswip_phylink_mac_link_up). Thanks to Andrew for the hint with the phylink documentation. - Clarify that GSWIP_MII_CFG_RMII_CLK is ignored by the hardware in the description of the second patch as suggested by Hauke - Don't set GSWIP_MII_CFG_RGMII_IBS in the second patch as we don't have any hardware available for testing this. The patch description now also reflects this. - Added Andrew's Reviewed-by to the first patch (thank you!) ==================== Signed-off-by:
-
Martin Blumenstingl authored
There are a few more bits in the GSWIP_MII_CFG register for which we did rely on the boot-loader (or the hardware defaults) to set them up properly. For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK bit and also we should un-set it for non-RMII PHYs. The GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes. The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's no known hardware which uses this (so it is not tested yet). Clear the xMII isolation bit when set at initialization time if it was previously set by the bootloader. Not doing so could lead to no traffic (neither RX nor TX) on a port with this bit set. While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to manage it because this bit is self-clearning when set. We still add it here to get a better overview of the GSWIP_MII_CFG register. Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Cc: stable@vger.kernel.org Suggested-by:
Hauke Mehrtens <hauke@hauke-m.de> Acked-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Martin Blumenstingl authored
PHY auto polling on the GSWIP hardware can be used so link changes (speed, link up/down, etc.) can be detected automatically. Internally GSWIP reads the PHY's registers for this functionality. Based on this automatic detection GSWIP can also automatically re-configure it's port settings. Unfortunately this auto polling (and configuration) mechanism seems to cause various issues observed by different people on different devices: - FritzBox 7360v2: the two Gbit/s ports (connected to the two internal PHY11G instances) are working fine but the two Fast Ethernet ports (using an AR8030 RMII PHY) are completely dead (neither RX nor TX are received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This makes the PHY auto polling state machine (rightfully?) think that the established link speed (when the other side is Gbit/s capable) is 1Gbit/s. - None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are connected to the internal PHY11G GPHYs while the other three are external RGMII PHYs) are working. Neither RX nor TX traffic was observed. It is not clear which part of the PHY auto polling state- machine caused this. - FritzBox 7412 (only one LAN port which is connected to one of the internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing random disconnects (link down events could be seen). Sometimes all traffic would stop after such disconnect. It is not clear which part of the PHY auto polling state-machine cauased this. - TP-Link TD-W9980 (two ports are connected to the internal GPHYs running in PHY11G / Gbit/s mode, the other two are external RGMII PHYs) was affected by similar issues as the FritzBox 7412 just without the "link down" events Switch to software based configuration instead of PHY auto polling (and letting the GSWIP hardware configure the ports automatically) for the following link parameters: - link up/down - link speed - full/half duplex - flow control (RX / TX pause) After a big round of manual testing by various people (who helped test this on OpenWrt) it turns out that this fixes all reported issues. Additionally it can be considered more future proof because any "quirk" which is implemented for a PHY on the driver side can now be used with the GSWIP hardware as well because Linux is in control of the link parameters. As a nice side-effect this also solves a problem where fixed-links were not supported previously because we were relying on the PHY auto polling mechanism, which cannot work for fixed-links as there's no PHY from where it can read the registers. Configuring the link settings on the GSWIP ports means that we now use the settings from device-tree also for ports with fixed-links. Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Fixes: 3e6fdeb2 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock") Cc: stable@vger.kernel.org Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueDavid S. Miller authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-04-08 This series contains updates to i40e and ice drivers. Grzegorz fixes the ordering of parameters to i40e_aq_get_phy_register() which is causing incorrect information to be reported. Arkadiusz fixes various sparse issues reported on the i40e driver. Yongxin Liu fixes a memory leak with aRFS following resume from suspend for ice driver. ==================== Signed-off-by: -
Pavel Tikhomirov authored
Reproduce: modprobe sch_teql tc qdisc add dev teql0 root teql0 This leads to (for instance in Centos 7 VM) OOPS: [ 532.366633] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 [ 532.366733] IP: [<ffffffffc06124a8>] teql_destroy+0x18/0x100 [sch_teql] [ 532.366825] PGD 80000001376d5067 PUD 137e37067 PMD 0 [ 532.366906] Oops: 0000 [#1] SMP [ 532.366987] Modules linked in: sch_teql ... [ 532.367945] CPU: 1 PID: 3026 Comm: tc Kdump: loaded Tainted: G ------------ T 3.10.0-1062.7.1.el7.x86_64 #1 [ 532.368041] Hardware name: Virtuozzo KVM, BIOS 1.11.0-2.vz7.2 04/01/2014 [ 532.368125] task: ffff8b7d37d31070 ti: ffff8b7c9fdbc000 task.ti: ffff8b7c9fdbc000 [ 532.368224] RIP: 0010:[<ffffffffc06124a8>] [<ffffffffc06124a8>] teql_destroy+0x18/0x100 [sch_teql] [ 532.368320] RSP: 0018:ffff8b7c9fdbf8e0 EFLAGS: 00010286 [ 532.368394] RAX: ffffffffc0612490 RBX: ffff8b7cb1565e00 RCX: ffff8b7d35ba2000 [ 532.368476] RDX: ffff8b7d35ba2000 RSI: 0000000000000000 RDI: ffff8b7cb1565e00 [ 532.368557] RBP: ffff8b7c9fdbf8f8 R08: ffff8b7d3fd1f140 R09: ffff8b7d3b001600 [ 532.368638] R10: ffff8b7d3b001600 R11: ffffffff84c7d65b R12: 00000000ffffffd8 [ 532.368719] R13: 0000000000008000 R14: ffff8b7d35ba2000 R15: ffff8b7c9fdbf9a8 [ 532.368800] FS: 00007f6a4e872740(0000) GS:ffff8b7d3fd00000(0000) knlGS:0000000000000000 [ 532.368885] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 532.368961] CR2: 00000000000000a8 CR3: 00000001396ee000 CR4: 00000000000206e0 [ 532.369046] Call Trace: [ 532.369159] [<ffffffff84c8192e>] qdisc_create+0x36e/0x450 [ 532.369268] [<ffffffff846a9b49>] ? ns_capable+0x29/0x50 [ 532.369366] [<ffffffff849afde2>] ? nla_parse+0x32/0x120 [ 532.369442] [<ffffffff84c81b4c>] tc_modify_qdisc+0x13c/0x610 [ 532.371508] [<ffffffff84c693e7>] rtnetlink_rcv_msg+0xa7/0x260 [ 532.372668] [<ffffffff84907b65>] ? sock_has_perm+0x75/0x90 [ 532.373790] [<ffffffff84c69340>] ? rtnl_newlink+0x890/0x890 [ 532.374914] [<ffffffff84c8da7b>] netlink_rcv_skb+0xab/0xc0 [ 532.376055] [<ffffffff84c63708>] rtnetlink_rcv+0x28/0x30 [ 532.377204] [<ffffffff84c8d400>] netlink_unicast+0x170/0x210 [ 532.378333] [<ffffffff84c8d7a8>] netlink_sendmsg+0x308/0x420 [ 532.379465] [<ffffffff84c2f3a6>] sock_sendmsg+0xb6/0xf0 [ 532.380710] [<ffffffffc034a56e>] ? __xfs_filemap_fault+0x8e/0x1d0 [xfs] [ 532.381868] [<ffffffffc034a75c>] ? xfs_filemap_fault+0x2c/0x30 [xfs] [ 532.383037] [<ffffffff847ec23a>] ? __do_fault.isra.61+0x8a/0x100 [ 532.384144] [<ffffffff84c30269>] ___sys_sendmsg+0x3e9/0x400 [ 532.385268] [<ffffffff847f3fad>] ? handle_mm_fault+0x39d/0x9b0 [ 532.386387] [<ffffffff84d88678>] ? __do_page_fault+0x238/0x500 [ 532.387472] [<ffffffff84c31921>] __sys_sendmsg+0x51/0x90 [ 532.388560] [<ffffffff84c31972>] SyS_sendmsg+0x12/0x20 [ 532.389636] [<ffffffff84d8dede>] system_call_fastpath+0x25/0x2a [ 532.390704] [<ffffffff84d8de21>] ? system_call_after_swapgs+0xae/0x146 [ 532.391753] Code: 00 00 00 00 00 00 5b 5d c3 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 55 48 89 e5 41 55 41 54 53 48 8b b7 48 01 00 00 48 89 fb <48> 8b 8e a8 00 00 00 48 85 c9 74 43 48 89 ca eb 0f 0f 1f 80 00 [ 532.394036] RIP [<ffffffffc06124a8>] teql_destroy+0x18/0x100 [sch_teql] [ 532.395127] RSP <ffff8b7c9fdbf8e0> [ 532.396179] CR2: 00000000000000a8 Null pointer dereference happens on master->slaves dereference in teql_destroy() as master is null-pointer. When qdisc_create() calls teql_qdisc_init() it imediately fails after check "if (m->dev == dev)" because both devices are teql0, and it does not set qdisc_priv(sch)->m leaving it zero on error path, then qdisc_create() imediately calls teql_destroy() which does not expect zero master pointer and we get OOPS. Fixes: 87b60cfa ("net_sched: fix error recovery at qdisc creation") Signed-off-by:
Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Reviewed-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf 2021-04-08 The following pull-request contains BPF updates for your *net* tree. We've added 4 non-merge commits during the last 2 day(s) which contain a total of 4 files changed, 31 insertions(+), 10 deletions(-). The main changes are: 1) Validate and reject invalid JIT branch displacements, from Piotr Krysiuk. 2) Fix incorrect unhash restore as well as fwd_alloc memory accounting in sock map, from John Fastabend. ==================== Signed-off-by: -
David S. Miller authored
Merge tag 'mac80211-for-net-2021-04-08.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes berg says: ==================== Various small fixes: * S1G beacon validation * potential leak in nl80211 * fast-RX confusion with 4-addr mode * erroneous WARN_ON that userspace can trigger * wrong time units in virt_wifi * rfkill userspace API breakage * TXQ AC confusing that led to traffic stopped forever * connection monitoring time after/before confusion * netlink beacon head validation buffer overrun ==================== Signed-off-by:
-
Stephen Hemminger authored
Setting iftoken can fail for several different reasons but there and there was no report to user as to the cause. Add netlink extended errors to the processing of the request. This requires adding additional argument through rtnl_af_ops set_link_af callback. Reported-by:
Hongren Zheng <li@zenithal.me> Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
David S. Miller authored
Vlad Buslov says: ==================== Action initalization fixes This series fixes reference counting of action instances and modules in several parts of action init code. The first patch reverts previous fix that didn't properly account for rollback from a failure in the middle of the loop in tcf_action_init() which is properly fixed by the following patch. ==================== Signed-off-by: -
Vlad Buslov authored
With recent changes that separated action module load from action initialization tcf_action_init() function error handling code was modified to manually release the loaded modules if loading/initialization of any further action in same batch failed. For the case when all modules successfully loaded and some of the actions were initialized before one of them failed in init handler. In this case for all previous actions the module will be released twice by the error handler: First time by the loop that manually calls module_put() for all ops, and second time by the action destroy code that puts the module after destroying the action. Reproduction: $ sudo tc actions add action simple sdata \"2\" index 2 $ sudo tc actions add action simple sdata \"1\" index 1 \ action simple sdata \"2\" index 2 RTNETLINK answers: File exists We have an error talking to the kernel $ sudo tc actions ls action simple total acts 1 action order 0: Simple <"2"> index 2 ref 1 bind 0 $ sudo tc actions flush action simple $ sudo tc actions ls action simple $ sudo tc actions add action simple sdata \"2\" index 2 Error: Failed to load TC action module. We have an error talking to the kernel $ lsmod | grep simple act_simple 20480 -1 Fix the issue by modifying module reference counting handling in action initialization code: - Get module reference in tcf_idr_create() and put it in tcf_idr_release() instead of taking over the reference held by the caller. - Modify users of tcf_action_init_1() to always release the module reference which they obtain before calling init function instead of assuming that created action takes over the reference. - Finally, modify tcf_action_init_1() to not release the module reference when overwriting existing action as this is no longer necessary since both upper and lower layers obtain and manage their own module references independently. Fixes: d349f997 ("net_sched: fix RTNL deadlock again caused by request_module()") Suggested-by:Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Vlad Buslov <vladbu@nvidia.com> Signed-off-by:
-
Vlad Buslov authored
Action init code increments reference counter when it changes an action. This is the desired behavior for cls API which needs to obtain action reference for every classifier that points to action. However, act API just needs to change the action and releases the reference before returning. This sequence breaks when the requested action doesn't exist, which causes act API init code to create new action with specified index, but action is still released before returning and is deleted (unless it was referenced concurrently by cls API). Reproduction: $ sudo tc actions ls action gact $ sudo tc actions change action gact drop index 1 $ sudo tc actions ls action gact Extend tcf_action_init() to accept 'init_res' array and initialize it with action->ops->init() result. In tcf_action_add() remove pointers to created actions from actions array before passing it to tcf_action_put_many(). Fixes: cae422f3 ("net: sched: use reference counting action init") Reported-by:
Kumar Kartikeya Dwivedi <memxor@gmail.com> Signed-off-by:
-
Vlad Buslov authored
This reverts commit 6855e821. Following commit in series fixes the issue without introducing regression in error rollback of tcf_action_destroy(). Signed-off-by:
-
Yongxin Liu authored
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then irq_free_descs() will be eventually called to free irq and its descriptor. In ice_resume(), ice_init_interrupt_scheme() is called to allocate new irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap maybe cannot be freed, if the irqs that released in ice_suspend() were reassigned to other devices, which makes irq descriptor's affinity_notify lost. So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which can make sure all irq_glue and cpu_rmap can be correctly released before corresponding irq and descriptor are released. Fix the following memory leak. unreferenced object 0xffff95bd951afc00 (size 512): comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s) hex dump (first 32 bytes): 18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p....... 00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................ backtrace: [<0000000072e4b914>] __kmalloc+0x336/0x540 [<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0 [<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice] [<000000002370a632>] ice_probe+0x941/0x1180 [ice] [<00000000d692edba>] local_pci_probe+0x47/0xa0 [<00000000503934f0>] work_for_cpu_fn+0x1a/0x30 [<00000000555a9e4a>] process_one_work+0x1dd/0x410 [<000000002c4b414a>] worker_thread+0x221/0x3f0 [<00000000bb2b556b>] kthread+0x14c/0x170 [<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30 unreferenced object 0xffff95bd81b0a2a0 (size 96): comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s) hex dump (first 32 bytes): 38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8............... b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................ backtrace: [<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0 [<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0 [<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice] [<000000002370a632>] ice_probe+0x941/0x1180 [ice] [<00000000d692edba>] local_pci_probe+0x47/0xa0 [<00000000503934f0>] work_for_cpu_fn+0x1a/0x30 [<00000000555a9e4a>] process_one_work+0x1dd/0x410 [<000000002c4b414a>] worker_thread+0x221/0x3f0 [<00000000bb2b556b>] kthread+0x14c/0x170 [<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30 Fixes: 769c500d ("ice: Add advanced power mgmt for WoL") Signed-off-by:Yongxin Liu <yongxin.liu@windriver.com> Tested-by:
Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Arkadiusz Kubalewski authored
Set proper return values inside error checking if-statements. Previously following warning was produced when compiling against sparse. i40e_main.c:15162 i40e_init_recovery_mode() warn: missing error code 'err' Fixes: 4ff0ee1a ("i40e: Introduce recovery mode support") Signed-off-by:
Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by:
Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by:
Dave Switzer <david.switzer@intel.com> Signed-off-by:
-
Arkadiusz Kubalewski authored
Remove vsi->netdev->name from the trace. This is redundant information. With the devinfo trace, the adapter is already identifiable. Previously following error was produced when compiling against sparse. i40e_main.c:2571 i40e_sync_vsi_filters() error: we previously assumed 'vsi->netdev' could be null (see line 2323) Fixes: b603f9dc ("i40e: Log info when PF is entering and leaving Allmulti mode.") Signed-off-by:
-
Arkadiusz Kubalewski authored
Init pointer with NULL in default switch case statement. Previously the error was produced when compiling against sparse. i40e_debugfs.c:582 i40e_dbg_dump_desc() error: uninitialized symbol 'ring'. Fixes: 44ea803e ("i40e: introduce new dump desc XDP command") Signed-off-by:
-
Arkadiusz Kubalewski authored
Remove error handling through pointers. Instead use plain int to return value from i40e_run_xdp(...). Previously: - sparse errors were produced during compilation: i40e_txrx.c:2338 i40e_run_xdp() error: (-2147483647) too low for ERR_PTR i40e_txrx.c:2558 i40e_clean_rx_irq() error: 'skb' dereferencing possible ERR_PTR() - sk_buff* was used to return value, but it has never had valid pointer to sk_buff. Returned value was always int handled as a pointer. Fixes: 0c8493d9 ("i40e: add XDP support for pass and drop actions") Fixes: 2e689312 ("i40e: split XDP_TX tail and XDP_REDIRECT map flushing") Signed-off-by:
-
Grzegorz Siwik authored
Change parameters order in aq_get_phy_register() due to wrong statistics in PHY reported by ethtool. Previously all PHY statistics were exactly the same for all interfaces Now statistics are reported correctly - different for different interfaces Fixes: 0514db37 ("i40e: Extend PHY access with page change flag") Signed-off-by:
Grzegorz Siwik <grzegorz.siwik@intel.com> Tested-by:
-
Johannes Berg authored
If the beacon head attribute (NL80211_ATTR_BEACON_HEAD) is too short to even contain the frame control field, we access uninitialized data beyond the buffer. Fix this by checking the minimal required size first. We used to do this until S1G support was added, where the fixed data portion has a different size. Reported-and-tested-by: syzbot+72b99dcf4607e8c770f3@syzkaller.appspotmail.com Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Fixes: 1d47f119 ("nl80211: correctly validate S1G beacon head") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20210408154518.d9b06d39b4ee.Iff908997b2a4067e8d456b3cb96cab9771d252b8@changeidSigned-off-by:
-
Piotr Krysiuk authored
The branch displacement logic in the BPF JIT compilers for x86 assumes that, for any generated branch instruction, the distance cannot increase between optimization passes. But this assumption can be violated due to how the distances are computed. Specifically, whenever a backward branch is processed in do_jit(), the distance is computed by subtracting the positions in the machine code from different optimization passes. This is because part of addrs[] is already updated for the current optimization pass, before the branch instruction is visited. And so the optimizer can expand blocks of machine code in some cases. This can confuse the optimizer logic, where it assumes that a fixed point has been reached for all machine code blocks once the total program size stops changing. And then the JIT compiler can output abnormal machine code containing incorrect branch displacements. To mitigate this issue, we assert that a fixed point is reached while populating the output image. This rejects any problematic programs. The issue affects both x86-32 and x86-64. We mitigate separately to ease backporting. Signed-off-by:
Piotr Krysiuk <piotras@gmail.com> Reviewed-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Piotr Krysiuk authored
The branch displacement logic in the BPF JIT compilers for x86 assumes that, for any generated branch instruction, the distance cannot increase between optimization passes. But this assumption can be violated due to how the distances are computed. Specifically, whenever a backward branch is processed in do_jit(), the distance is computed by subtracting the positions in the machine code from different optimization passes. This is because part of addrs[] is already updated for the current optimization pass, before the branch instruction is visited. And so the optimizer can expand blocks of machine code in some cases. This can confuse the optimizer logic, where it assumes that a fixed point has been reached for all machine code blocks once the total program size stops changing. And then the JIT compiler can output abnormal machine code containing incorrect branch displacements. To mitigate this issue, we assert that a fixed point is reached while populating the output image. This rejects any problematic programs. The issue affects both x86-32 and x86-64. We mitigate separately to ease backporting. Signed-off-by:
-
Johannes Berg authored
In case nl80211_parse_unsol_bcast_probe_resp() results in an error, need to "goto out" instead of just returning to free possibly allocated data. Fixes: 7443dcd1 ("nl80211: Unsolicited broadcast probe response support") Link: https://lore.kernel.org/r/20210408142833.d8bc2e2e454a.If290b1ba85789726a671ff0b237726d4851b5b0f@changeidSigned-off-by:
-
Johannes Berg authored
We need to check the length of this element so that we don't access data beyond its end. Fix that. Fixes: 9eaffe50 ("cfg80211: convert S1G beacon to scan results") Link: https://lore.kernel.org/r/20210408142826.f6f4525012de.I9fdeff0afdc683a6024e5ea49d2daa3cd2459d11@changeidSigned-off-by:
-
A. Cody Schuffelen authored
cfg80211_inform_bss expects to receive a TSF value, but is given the time since boot in nanoseconds. TSF values are expected to be at microsecond scale rather than nanosecond scale. Signed-off-by:
A. Cody Schuffelen <schuffelen@google.com> Link: https://lore.kernel.org/r/20210318200419.1421034-1-schuffelen@google.comSigned-off-by:
-
Du Cheng authored
A WARN_ON(wdev->conn) would trigger in cfg80211_sme_connect(), if multiple send_msg(NL80211_CMD_CONNECT) system calls are made from the userland, which should be anticipated and handled by the wireless driver. Remove this WARN_ON() to prevent kernel panic if kernel is configured to "panic_on_warn". Bug reported by syzbot. Reported-by: syzbot+5f9392825de654244975@syzkaller.appspotmail.com Signed-off-by:
Du Cheng <ducheng2@gmail.com> Link: https://lore.kernel.org/r/20210407162756.6101-1-ducheng2@gmail.comSigned-off-by:
-
Ben Greear authored
The incorrect timeout check caused probing to happen when it did not need to happen. This in turn caused tx performance drop for around 5 seconds in ath10k-ct driver. Possibly that tx drop is due to a secondary issue, but fixing the probe to not happen when traffic is running fixes the symptom. Signed-off-by:
Ben Greear <greearb@candelatech.com> Fixes: 9abf4e49 ("mac80211: optimize station connection monitor") Acked-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20210330230749.14097-1-greearb@candelatech.comSigned-off-by:
-
Johannes Berg authored
Normally, TXQs have txq->tid = tid; txq->ac = ieee80211_ac_from_tid(tid); However, the special management TXQ actually has txq->tid = IEEE80211_NUM_TIDS; // 16 txq->ac = IEEE80211_AC_VO; This makes sense, but ieee80211_ac_from_tid(16) is the same as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE. Now, normally this is fine. However, if the netdev queues were stopped, then the code in ieee80211_tx_dequeue() will propagate the stop from the interface (vif->txqs_stopped[]) if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as stopped. On wake, however, __ieee80211_wake_txqs() will wake the TXQ if AC 0 (txq->ac) is woken up. If a driver stops all queues with ieee80211_stop_tx_queues() and then wakes them again with ieee80211_wake_tx_queues(), the ieee80211_wake_txqs() tasklet will run to resync queue and TXQ state. If all queues were woken, then what'll happen is that _ieee80211_wake_txqs() will run in order of HW queues 0-3, typically (and certainly for iwlwifi) corresponding to ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in order 0-3. When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll wake up the management TXQ (remember its tid is 16), and the driver's wake_tx_queue() will be called. That tries to get a frame, which will immediately *stop* the TXQ again, because now we check against AC 2, and AC 2 hasn't yet been marked as woken up again in sdata->vif.txqs_stopped[] since we're only in the __ieee80211_wake_txqs() call for AC 0. Thus, the management TXQ will never be started again. Fix this by checking txq->ac directly instead of calculating the AC as ieee80211_ac_from_tid(txq->tid). Fixes: adf8ed01 ("mac80211: add an optional TXQ for other PS-buffered frames") Acked-by:
Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeidSigned-off-by:
-
Johannes Berg authored
Recompiling with the new extended version of struct rfkill_event broke systemd in *two* ways: - It used "sizeof(struct rfkill_event)" to read the event, but then complained if it actually got something != 8, this broke it on new kernels (that include the updated API); - It used sizeof(struct rfkill_event) to write a command, but didn't implement the intended expansion protocol where the kernel returns only how many bytes it accepted, and errored out due to the unexpected smaller size on kernels that didn't include the updated API. Even though systemd has now been fixed, that fix may not be always deployed, and other applications could potentially have similar issues. As such, in the interest of avoiding regressions, revert the default API "struct rfkill_event" back to the original size. Instead, add a new "struct rfkill_event_ext" that extends it by the new field, and even more clearly document that applications should be prepared for extensions in two ways: * write might only accept fewer bytes on older kernels, and will return how many to let userspace know which data may have been ignored; * read might return anything between 8 (the original size) and whatever size the application sized its buffer at, indicating how much event data was supported by the kernel. Perhaps that will help avoid such issues in the future and we won't have to come up with another version of the struct if we ever need to extend it again. Applications that want to take advantage of the new field will have to be modified to use struct rfkill_event_ext instead now, which comes with the danger of them having already been updated to use it from 'struct rfkill_event', but I found no evidence of that, and it's still relatively new. Cc: stable@vger.kernel.org # 5.11 Reported-by:
Takashi Iwai <tiwai@suse.de> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM/Clang v12.0.0-r4 (x86-64) Link: https://lore.kernel.org/r/20210319232510.f1a139cfdd9c.Ic5c7c9d1d28972059e132ea653a21a427c326678@changeidSigned-off-by:
-
Seevalamuthu Mariappan authored
In some race conditions, with more clients and traffic configuration, below crash is seen when making the interface down. sta->fast_rx wasn't cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev) which has been deleted already. Resolve this by clearing sta->fast_rx pointer when STA removes from a 4-addr VLAN. [ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004 [ 239.449531] pgd = 80204000 ... [ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227 [ 239.481591] Hardware name: Generic DT based system [ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000 [ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c [ 239.497823] LR is at 0xbe08fc54 ... [ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac) [ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4) [ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211]) [ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8 0211]) [ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k]) [ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k]) [ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb] ) [ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c) [ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228) [ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108) [ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4) [ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94) [ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74) Signed-off-by:Seevalamuthu Mariappan <seevalam@codeaurora.org> Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.orgSigned-off-by:
-
- 07 Apr, 2021 7 commits
-
-
Anirudh Rayabharam authored
Multiple ttys try to claim the same the minor number causing a double unregistration of the same device. The first unregistration succeeds but the next one results in a null-ptr-deref. The get_free_serial_index() function returns an available minor number but doesn't assign it immediately. The assignment is done by the caller later. But before this assignment, calls to get_free_serial_index() would return the same minor number. Fix this by modifying get_free_serial_index to assign the minor number immediately after one is found to be and rename it to obtain_minor() to better reflect what it does. Similary, rename set_serial_by_index() to release_minor() and modify it to free up the minor number of the given hso_serial. Every obtain_minor() should have corresponding release_minor() call. Fixes: 72dc1c09 ("HSO: add option hso driver") Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Anirudh Rayabharam <mail@anirudhrb.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'ieee802154-for-davem-2021-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan Stefan Schmidt says: ==================== pull-request: ieee802154 for net 2021-04-07 An update from ieee802154 for your *net* tree. Most of these are coming from the flood of syzkaller reports lately got for the ieee802154 subsystem. There are likely to come more for this, but this is a good batch to get out for now. Alexander Aring created a patchset to avoid llsec handling on a monitor interface, which we do not support. Alex Shi removed a unused macro. Pavel Skripkin fixed another protection fault found by syzkaller. ==================== Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-2021-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.12 Third, and last, set of fixes for v5.12. Small fixes, iwlwifi having most of them. brcmfmac regression caused by cfg80211 changes is the most important here. iwlwifi * fix a lockdep warning * fix regulatory feature detection in certain firmware versions * new hardware support * fix lockdep warning * mvm: fix beacon protection checks mt76 * mt7921: fix airtime reporting brcmfmac * fix a deadlock regression ==================== Signed-off-by:
-
David S. Miller authored
Danielle Ratson says: ==================== Fix link_mode derived params functionality Currently, link_mode parameter derives 3 other link parameters, speed, lanes and duplex, and the derived information is sent to user space. Few bugs were found in that functionality. First, some drivers clear the 'ethtool_link_ksettings' struct in their get_link_ksettings() callback and cause receiving wrong link mode information in user space. And also, some drivers can report random values in the 'link_mode' field and cause general protection fault. Second, the link parameters are only derived in netlink path so in ioctl path, we don't any reasonable values. Third, setting 'speed 10000 lanes 1' fails since the lanes parameter wasn't set for ETHTOOL_LINK_MODE_10000baseR_FEC_BIT. Patch #1 solves the first two problems by removing link_mode parameter and deriving the link parameters in driver instead of ethtool. Patch #2 solves the third one, by setting the lanes parameter for the link_mode. v3: * Remove the link_mode parameter in the first patch to solve both two issues from patch#1 and patch#2. * Add the second patch to solve the third issue. v2: * Add patch #2. * Introduce 'cap_link_mode_supported' instead of adding a validity field to 'ethtool_link_ksettings' struct in patch #1. ==================== Signed-off-by: -
Danielle Ratson authored
Lanes field is missing for ETHTOOL_LINK_MODE_10000baseR_FEC_BIT link mode and it causes a failure when trying to set 'speed 10000 lanes 1' on Spectrum-2 machines when autoneg is set to on. Add the lanes parameter for ETHTOOL_LINK_MODE_10000baseR_FEC_BIT link mode. Fixes: c8907043 ("ethtool: Get link mode in use instead of speed and duplex parameters") Signed-off-by:
Danielle Ratson <danieller@nvidia.com> Reviewed-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
Danielle Ratson authored
Some drivers clear the 'ethtool_link_ksettings' struct in their get_link_ksettings() callback, before populating it with actual values. Such drivers will set the new 'link_mode' field to zero, resulting in user space receiving wrong link mode information given that zero is a valid value for the field. Another problem is that some drivers (notably tun) can report random values in the 'link_mode' field. This can result in a general protection fault when the field is used as an index to the 'link_mode_params' array [1]. This happens because such drivers implement their set_link_ksettings() callback by simply overwriting their private copy of 'ethtool_link_ksettings' struct with the one they get from the stack, which is not always properly initialized. Fix these problems by removing 'link_mode' from 'ethtool_link_ksettings' and instead have drivers call ethtool_params_from_link_mode() with the current link mode. The function will derive the link parameters (e.g., speed) from the link mode and fill them in the 'ethtool_link_ksettings' struct. v3: * Remove link_mode parameter and derive the link parameters in the driver instead of passing link_mode parameter to ethtool and derive it there. v2: * Introduce 'cap_link_mode_supported' instead of adding a validity field to 'ethtool_link_ksettings' struct. [1] general protection fault, probably for non-canonical address 0xdffffc00f14cc32c: 0000 [#1] PREEMPT SMP KASAN KASAN: probably user-memory-access in range [0x000000078a661960-0x000000078a661967] CPU: 0 PID: 8452 Comm: syz-executor360 Not tainted 5.11.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:__ethtool_get_link_ksettings+0x1a3/0x3a0 net/ethtool/ioctl.c:446 Code: b7 3e fa 83 fd ff 0f 84 30 01 00 00 e8 16 b0 3e fa 48 8d 3c ed 60 d5 69 8a 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 +38 d0 7c 08 84 d2 0f 85 b9 RSP: 0018:ffffc900019df7a0 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffff888026136008 RCX: 0000000000000000 RDX: 00000000f14cc32c RSI: ffffffff873439ca RDI: 000000078a661960 RBP: 00000000ffff8880 R08: 00000000ffffffff R09: ffff88802613606f R10: ffffffff873439bc R11: 0000000000000000 R12: 0000000000000000 R13: ffff88802613606c R14: ffff888011d0c210 R15: ffff888011d0c210 FS: 0000000000749300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004b60f0 CR3: 00000000185c2000 CR4: 00000000001506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: linkinfo_prepare_data+0xfd/0x280 net/ethtool/linkinfo.c:37 ethnl_default_notify+0x1dc/0x630 net/ethtool/netlink.c:586 ethtool_notify+0xbd/0x1f0 net/ethtool/netlink.c:656 ethtool_set_link_ksettings+0x277/0x330 net/ethtool/ioctl.c:620 dev_ethtool+0x2b35/0x45d0 net/ethtool/ioctl.c:2842 dev_ioctl+0x463/0xb70 net/core/dev_ioctl.c:440 sock_do_ioctl+0x148/0x2d0 net/socket.c:1060 sock_ioctl+0x477/0x6a0 net/socket.c:1177 vfs_ioctl fs/ioctl.c:48 [inline] __do_sys_ioctl fs/ioctl.c:753 [inline] __se_sys_ioctl fs/ioctl.c:739 [inline] __x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: c8907043 ("ethtool: Get link mode in use instead of speed and duplex parameters") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5 fixes 2021-04-06 This series provides some fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by:
-
