Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.

For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David S. Miller <davem@davemloft.net>

Add the Cadence macb ethernet controller in at91sam9g45 and at91sam9g20
.dtsi and enable it in at91sam9m10g45ek and usb_a9g20 board device tree file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Allow the device tree to provide the mac address and the phy mode.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>

GEM has configurable receive buffer sizes so requires this to be
programmed up.  Any size < 2048 and a multiple of 64 bytes is permitted.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Some GEM implementations may support DMA bus widths up to 128 bits.  We
can get the maximum supported DMA bus width from the design
configuration register so use that to program the device up.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

GEM devices have a different number of statistics registers and they
are at a different offset to MACB devices.  Make the statistics
collection method dependent on device type.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

GEM devices support larger clock divisors and have a different
range of divisors.  Program the MDIO clock divisors based on the
device type.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The Cadence GEM is based on the MACB Ethernet controller but has a few
small changes with regards to register and bitfield placement.  This
patch detects the presence of a GEM by reading the module ID register
and setting a flag appropriately.

This handles the new HW address, USRIO and hash register base register
locations in GEM.

v3: - convert to macb_is_gem() inline rather than storing a boolean
      flag
    - handle rx_overrun stats for gem
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

macb is already using the dev_dbg() and friends helpers so use netdev_()
along with a pr_fmt() definition to make the printing a little cleaner.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin.  Create a common
macb_platform_data for macb that both at91 and avr32 can use.  In
future we can use this to support other architectures that use the
same IP block with the macb driver.

v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

AT91 now provides both "pclk" and "hclk" aliases for the the macb
device so we can use the same clk handling paths for both AT91 and
AVR32.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The macb driver expects clocks with the names "pclk" and "hclk".  We
currently provide "macb_clk" but to fit in line with other
architectures (namely AVR32), provide "pclk" and a fake "hclk".

Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu: omap: Fix compile failure

* 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl:
  pinctrl: hide subsystem from the populace
  pinctrl: fix "warning: 'struct pinctrl_dev' declared inside parameter list"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  fsl-rio: fix compile error

* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
  gpio: pca953x: propagate the errno from the chip_init functions
  gpio: pca953x: remove unneeded check for chip type
  gpio/omap: check return value from irq_alloc_generic_chip
  gpio/omap: replace MOD_REG_BIT macro with static inline

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
  blackfin: Fixup export.h includes
  Blackfin: add serial TX IRQ in individual platform resource

On a corrupted file system the ->len field could be wrong leading to
a buffer overflow.
Reported-and-acked-by: Clement LECIGNE <clement.lecigne@netasq.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The "#include <linux/module.h>" was replaced by "#include <linux/export.h>"
in the patch "powerpc: various straight conversions from module.h --> export.h".
This will cause the following compile problem:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:296: error: implicit declaration of function 'search_exception_tables'.

The file fsl_rio.c needs the declaration of function "search_exception_tables"
in the header file "linux/module.h".
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Commit 8dc7a9c8 ("blackfin: Add export.h to files using
EXPORT_SYMBOL/THIS_MODULE") inserted some of the include statements into
sections protected by an unrelated #if CONFIG_... statement. This can cause,
depending on the configuration used, warnings like this one:

	arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: data definition has no type or storage class
	arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
	arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: parameter names (without types) in function declaration

This patch fixes it by moving the includes out of the #if protected sections.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>

The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips,
so move the values to the platform resources.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>

* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
  ARM: mach-shmobile: cpuidle single/global and last_state fixes
  ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
  ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
  ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
  ARM: mach-shmobile: ap4evb: remove white space from end of line
  ARM: mach-shmobile: clock-sh7372: remove un-necessary index
  ARM: mach-shmobile: kota2: add comment out separator
  ARM: mach-shmobile: sh73a0: add MMC data pin pull-up

* 'sh-fixes-for-linus' of git://github.com/pmundt/linux-sh:
  mailmap: Fix up some renesas attributions
  sh: clkfwk: Kill off remaining debugfs cruft.
  drivers: sh: Kill off dead pathname for runtime PM stub.
  drivers: sh: Generalize runtime PM platform stub.
  sh: Wire up process_vm syscalls.
  sh: clkfwk: add clk_rate_mult_range_round()
  serial: sh-sci: Fix up SH-2A SCIF support.
  sh: Fix cached/uncaced address calculation in 29bit mode

* git://github.com/rustyrussell/linux:
  virtio-pci: fix use after free

Commit 31a3ddda introduced
a use after free in virtio-pci. The main issue is
that the release method signals removal of the virtio device,
while remove signals removal of the pci device.

For example, on driver removal or hot-unplug,
virtio_pci_release_dev is called before virtio_pci_remove.
We then might get a crash as virtio_pci_remove tries to use the
device freed by virtio_pci_release_dev.

We allocate/free all resources together with the
pci device, so we can leave the release method empty.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms/combios: fix dynamic allocation of PM clock modes

After commit e978aa7d ("cpuidle: Move dev->last_residency update to
driver enter routine; remove dev->last_state") setting acpi_idle_suspend
to 1 by acpi_processor_suspend() causes the ACPI cpuidle routines to
return error codes continuously, which in turn causes cpuidle to lock up
(hard).

However, acpi_idle_suspend doesn't appear to be useful for any
particular purpose (it's racy and doesn't really provide any real
protection), so it can be removed, which makes the problem go away.
Reported-and-tested-by: Tomas M. <tmezzadra@gmail.com>
Reported-and-tested-by: Ferenc Wagner <wferi@niif.hu>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I missed the combios path when I updated the atombios pm code.

Reported by amarsh04 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm/imx: fix imx6q mmc error when mounting rootfs
  arm/imx: fix AUTO_ZRELADDR selection
  arm/imx: fix the references to ARCH_MX3
  ARM: mx51/53: set pwm clock parent to ipg_perclk
  arm/tegra: enable headphone detection gpio on seaboard
  arm/dt: Fix ventana SDHCI power-gpios
  arm/tegra: Don't create duplicate gpio and pinmux devices
  ARM: at91: Fix USBA gadget registration
  atmel/spi: fix missing probe
  at91/yl-9200: Fix section mismatch
  at91: vmalloc fix missing AT91_VIRT_BASE define
  ARM: at91: usart: drop static map regs for dbgu
  ARM: picoxcell: add extra temp register to addruart
  ARM: msm: fix compilation flags for MSM_SCM
  arm/mxs: fix mmc device adding for mach-mx28evk
  ARM: mxc: Remove test_for_ltirq
  ARM:i.MX: fix build error in clock-mx51-mx53.c
  ARM:i.MX: fix build error in tzic/avic.c
  ARM: mxc: fix local timer interrupt handling
  msm: boards: Fix fallout from removal of machine_desc in fixup

The variable i is removed by commit ded84337
"[CPUFREQ] db8500: remove unneeded for loop iteration over freq_table",
but current code to print available frequencies still uses the i variable.
Thus add the i variable back to fix below buld error:

  CC      drivers/cpufreq/db8500-cpufreq.o
drivers/cpufreq/db8500-cpufreq.c: In function 'db8500_cpufreq_init':
drivers/cpufreq/db8500-cpufreq.c:123: error: 'i' undeclared (first use in this function)
drivers/cpufreq/db8500-cpufreq.c:123: error: (Each undeclared identifier is reported only once
drivers/cpufreq/db8500-cpufreq.c:123: error: for each function it appears in.)
make[2]: *** [drivers/cpufreq/db8500-cpufreq.o] Error 1
make[1]: *** [drivers/cpufreq] Error 2
make: *** [drivers] Error 2

This patch also fixes using uninitialized i variable as array index.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (29 commits)
  m68k/mac: Remove mac_irq_{en,dis}able() wrappers
  m68k/irq: Remove obsolete support for user vector interrupt fixups
  m68k/irq: Remove obsolete m68k irq framework
  m68k/q40: Convert Q40/Q60 to genirq
  m68k/sun3: Convert Sun3/3x to genirq
  m68k/sun3: Use the kstat_irqs_cpu() wrapper
  m68k/apollo: Convert Apollo to genirq
  m68k/vme: Convert VME to genirq
  m68k/hp300: Convert HP9000/300 and HP9000/400 to genirq
  m68k/mac: Optimize interrupts using chain handlers
  m68k/mac: Convert Mac to genirq
  m68k/amiga: Optimize interrupts using chain handlers
  m68k/amiga: Convert Amiga to genirq
  m68k/amiga: Refactor amiints.c
  m68k/atari: Remove code and comments about different irq types
  m68k/atari: Convert Atari to genirq
  m68k/irq: Add genirq support
  m68k/irq: Remove obsolete IRQ_FLG_* users
  m68k/irq: Rename {,__}m68k_handle_int()
  m68k/irq: Add m68k_setup_irq_controller()
  ...

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] v4l2-ctrl: Send change events to all fh for auto cluster slave controls
  [media] v4l2-event: Don't set sev->fh to NULL on unsubscribe
  [media] v4l2-event: Remove pending events from fh event queue when unsubscribing
  [media] v4l2-event: Deny subscribing with a type of V4L2_EVENT_ALL
  [media] MAINTAINERS: add a maintainer for s5p-mfc driver
  [media] v4l: s5p-mfc: fix reported capabilities
  [media] media: vb2: reset queued list on REQBUFS(0) call
  [media] media: vb2: set buffer length correctly for all buffer types
  [media] media: vb2: add a check for uninitialized buffer
  [media] mxl111sf: fix build warning
  [media] mxl111sf: remove pointless if condition in mxl111sf_config_spi
  [media] mxl111sf: check for errors after mxl111sf_write_reg in mxl111sf_idac_config
  [media] mxl111sf: fix return value of mxl111sf_idac_config
  [media] uvcvideo: GET_RES should only be checked for BITMAP type menu controls

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/kvm: Fix build failure with HV KVM and CBE
  powerpc/ps3: Fix lv1_gpu_attribute hcall
  powerpc/ps3: Fix PS3 repository build warnings
  powerpc/ps3: irq: Remove IRQF_DISABLED
  powerpc/irq: Remove IRQF_DISABLED
  powerpc/numa: NUMA topology support for PowerNV
  powerpc: Add System RAM to /proc/iomem
  powerpc: Add KVM as module to defconfigs
  powerpc/kvm: Fix build with older toolchains
  powerpc, tqm5200: update tqm5200_defconfig to fit for charon board.
  powerpc/5200: add support for charon board

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: Fix missing system calls check on mips.

This needed the sfi IRQ 0xFF fix to go in first. It simply plumbs in the
bma023 driver with the firmware naming of it.
Signed-off-by: William Douglas <william.douglas@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Real world year equals the value in vrtc YEAR register plus an offset.
We used 1960 as the offset to make leap year consistent, but for a
device's first use, its YEAR register is 0 and the system year will
be parsed as 1960 which is not a valid UNIX time and will cause many
applications to fail mysteriously. So we use 1972 instead to fix this
issue.

Updated patch which adds a sanity check suggested by Mathias

This isn't a change in behaviour for systems, because 1972 is the one we
actually use. It's the old version in upstream which is out of sync with
all devices.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a build error. CE4100 with no serial errors because the alternate
function is only a prototype not a null function as intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
  pata_of_platform: Don't use NO_IRQ
  [libata] ahci: Add ASMedia ASM1061 support
  [libata] Issue SRST to Sil3726 PMP
  sata_sis.c: trivial spelling fix
  ahci_platform: use dev_get_platdata()
  [libata] libata-scsi.c: Add function parameter documentation

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: rename the option to nospace_cache
  Btrfs: handle bio_add_page failure gracefully in scrub
  Btrfs: fix deadlock caused by the race between relocation
  Btrfs: only map pages if we know we need them when reading the space cache
  Btrfs: fix orphan backref nodes
  Btrfs: Abstract similar code for btrfs_block_rsv_add{, _noflush}
  Btrfs: fix unreleased path in btrfs_orphan_cleanup()
  Btrfs: fix no reserved space for writing out inode cache
  Btrfs: fix nocow when deleting the item
  Btrfs: tweak the delayed inode reservations again
  Btrfs: rework error handling in btrfs_mount()
  Btrfs: close devices on all error paths in open_ctree()
  Btrfs: avoid null dereference and leaks when bailing from open_ctree()
  Btrfs: fix subvol_name leak on error in btrfs_mount()
  Btrfs: fix memory leak in btrfs_parse_early_options()
  Btrfs: fix our reservations for updating an inode when completing io
  Btrfs: fix oops on NULL trans handle in btrfs_truncate
  btrfs: fix double-free 'tree_root' in 'btrfs_mount()'