The TI DP83826 PHY can operate between two RMII modes:
	- master mode (PHY operates from a 25MHz clock reference)
        - slave mode (PHY operates from a 50MHz clock reference)

By default, the operation mode is configured by hardware straps.

Add support to configure the operation mode from within the driver.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TI DP83826 PHY can operate in either MII mode or RMII mode.
By default, it is configured by straps.
It can also be configured by writing to the bit 5 of register 0x17 - RMII
and Status Register (RCSR).

When phydev->interface is rmii, rmii mode must be enabled, otherwise
mii mode must be set.
This prevents misconfiguration of hw straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add property ti,rmii-mode to support selecting the RMII operation mode
between:
	- master mode (PHY operates from a 25MHz clock reference)
	- slave mode (PHY operates from a 50MHz clock reference)

If not set, the operation mode is configured by hardware straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink and ethtool have a trailing _ in the header guard. I must have
copy/pasted it into new guards, assuming it's a headers_install artifact.

This fixes build if system headers are old.

Fixes: 8f109e91 ("tools: ynl: include dpll and mptcp_pm in C codegen")
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240222234831.179181-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Make the local variable in GENL_REQ_ATTR_CHECK() const.
genl_info_dump() returns a const pointer, so the macro
is currently hard to use in genl dumps.

Link: https://lore.kernel.org/r/20240222222819.156320-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
tools: ynl: couple of cmdline enhancements

This is part of the original "netlink: specs: devlink: add the rest of
missing attribute definitions" set which was rejected [1]. These three
patches enhances the cmdline user comfort, allowing to pass flag
attribute with bool values and enum names instead of scalars.

[1] https://lore.kernel.org/all/20240220181004.639af931@kernel.org/
====================

Link: https://lore.kernel.org/r/20240222134351.224704-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

During decoding of messages coming from kernel, attribute values are
converted to enum names in case the attribute type is enum of bitfield32.

However, when user constructs json message, he has to pass plain scalar
values. See "state" "selector" and "value" attributes in following
examples:

$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml --do pin-set --json '{"id": 0, "parent-device": {"parent-id": 0, "state": 1}}'
$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/devlink.yaml --do port-set --json '{"bus-name": "pci", "dev-name": "0000:08:00.1", "port-index": 98304, "port-function": {"caps": {"selector": 1, "value": 1 }}}'

Allow user to pass strings containing enum names, convert them to scalar
values to be encoded into Netlink message:

$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml --do pin-set --json '{"id": 0, "parent-device": {"parent-id": 0, "state": "connected"}}'
$ sudo ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/devlink.yaml --do port-set --json '{"bus-name": "pci", "dev-name": "0000:08:00.1", "port-index": 98304, "port-function": {"caps": {"selector": ["roce-bit"], "value": ["roce-bit"] }}}'
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240222134351.224704-4-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As a preparation to handle enums for scalar values, unify the processing
of all scalar types in a single elif statement.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240222134351.224704-3-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The flag attr presence in Netlink message indicates value "true",
if it is missing in the message it means "false".

Allow user to specify attrname with value "true"/"false"
in json for flag attrs, treat "false" value properly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240222134351.224704-2-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

John Garry says:

====================
net: Don't bother filling in ethtool driver version

The drivers included in this series set the ethtool driver version to the
same as the default, UTS_RELEASE, so don't both doing this.

As noted by Masahiro in [0], with CONFIG_MODVERSIONS=y, some drivers could
be built as modules against a different kernel tree with differing
UTS_RELEASE. As such, these changes could lead to a change in behaviour.
However, defaulting to the core kernel UTS_RELEASE would be expected
behaviour.

[0] https://lore.kernel.org/all/CAK7LNASfTW+OMk1cJJWb4E6P+=k0FEsm_=6FDfDF_mTrxJCSMQ@mail.gmail.com/
====================

Link: https://lore.kernel.org/r/20240222090042.12609-1-john.g.garry@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The version is same as the default, so don't bother filling it in.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240222090042.12609-3-john.g.garry@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The version is same as the default, so don't bother filling it in.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240222090042.12609-2-john.g.garry@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

* Update the Kernel Doc for gelic_descr_set_tx_cmdstat()
  and gelic_net_setup_netdev() so that documented name
  and the actual name of the function match.

* Move define of GELIC_ALIGN() so that it is no longer
  between gelic_alloc_card_net() and it's Kernel Doc.

* Document netdev parameter of gelic_alloc_card_net()
  in a way consistent to the documentation of other netdev parameters
  in this file.

Addresses the following warnings flagged by ./scripts/kernel-doc -none:

  .../ps3_gelic_net.c:711: warning: expecting prototype for gelic_net_set_txdescr_cmdstat(). Prototype was for gelic_descr_set_tx_cmdstat() instead
  .../ps3_gelic_net.c:1474: warning: expecting prototype for gelic_ether_setup_netdev(). Prototype was for gelic_net_setup_netdev() instead
  .../ps3_gelic_net.c:1528: warning: expecting prototype for gelic_alloc_card_net(). Prototype was for GELIC_ALIGN() instead
  .../ps3_gelic_net.c:1531: warning: Function parameter or struct member 'netdev' not described in 'gelic_alloc_card_net'
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Link: https://lore.kernel.org/r/20240221-ps3-gelic-kdoc-v1-1-7629216d1340@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

mpls_gso_segment() assumes skb_inner_network_header() returns
a valid result:

  mpls_hlen = skb_inner_network_header(skb) - skb_network_header(skb);
  if (unlikely(!mpls_hlen || mpls_hlen % MPLS_HLEN))
        goto out;
  if (unlikely(!pskb_may_pull(skb, mpls_hlen)))

With syzbot reproducer, skb_inner_network_header() yields 0,
skb_network_header() returns 108, so this will
"pskb_may_pull(skb, -108)))" which triggers a newly added
DEBUG_NET_WARN_ON_ONCE() check:

------------[ cut here ]------------
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull_reason include/linux/skbuff.h:2723 [inline]
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull include/linux/skbuff.h:2739 [inline]
WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 mpls_gso_segment+0x773/0xaa0 net/mpls/mpls_gso.c:34
[..]
 skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53
 nsh_gso_segment+0x40a/0xad0 net/nsh/nsh.c:108
 skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53
 __skb_gso_segment+0x324/0x4c0 net/core/gso.c:124
 skb_gso_segment include/net/gso.h:83 [inline]
 [..]
 sch_direct_xmit+0x11a/0x5f0 net/sched/sch_generic.c:327
 [..]
 packet_sendmsg+0x46a9/0x6130 net/packet/af_packet.c:3113
 [..]

First iteration of this patch made mpls_hlen signed and changed
test to error out to "mpls_hlen <= 0 || ..".

Eric Dumazet said:
 > I was thinking about adding a debug check in skb_inner_network_header()
 > if inner_network_header is zero (that would mean it is not 'set' yet),
 > but this would trigger even after your patch.

So add new skb_inner_network_header_was_set() helper and use that.

The syzbot reproducer injects data via packet socket. The skb that gets
allocated and passed down the stack has ->protocol set to NSH (0x894f)
and gso_type set to SKB_GSO_UDP | SKB_GSO_DODGY.

This gets passed to skb_mac_gso_segment(), which sees NSH as ptype to
find a callback for.  nsh_gso_segment() retrieves next type:

        proto = tun_p_to_eth_p(nsh_hdr(skb)->np);

... which is MPLS (TUN_P_MPLS_UC). It updates skb->protocol and then
calls mpls_gso_segment().  Inner offsets are all 0, so mpls_gso_segment()
ends up with a negative header size.

In case more callers rely on silent handling of such large may_pull values
we could also 'legalize' this behaviour, either replacing the debug check
with (len > INT_MAX) test or removing it and instead adding a comment
before existing

 if (unlikely(len > skb->len))
    return SKB_DROP_REASON_PKT_TOO_SMALL;

test in pskb_may_pull_reason(), saying that this check also implicitly
takes care of callers that miscompute header sizes.

Cc: Simon Horman <horms@kernel.org>
Fixes: 219eee9c ("net: skbuff: add overflow debug check to pull/push helpers")
Reported-by: syzbot+99d15fcdb0132a1e1a82@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/00000000000043b1310611e388aa@google.com/rawSigned-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240222140321.14080-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, when you switch between branches or something like that and
rebuild, net/ethtool/ioctl.c has to be built again because it depends
on UTS_RELEASE.

By instead referencing a string variable stored in another object file,
this can be avoided.
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240220194244.2056384-1-jannh@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Serdes phy needs to operate at 2500 mode for 2.5G speed and 1000
mode for 1G/100M/10M speed.
Added changes to configure serdes phy and mac based on link speed.
Changing serdes phy speed involves multiple register writes for
serdes block. To avoid redundant write operations only update serdes
phy when new speed is different.
For 2500 speed MAC PCS autoneg needs to disabled. Added changes to
disable MAC PCS autoneg if ANE parameter is not set.
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Tested-by: Abhishek Chauhan <quic_abchauha@quicinc.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Through the routine bond_mii_monitor(), bonding driver inspects and commits
the slave state changes. During the times when slave state change and
failure in aqcuiring rtnl lock happen at the same time, the routine
bond_mii_monitor() reschedules itself to come around after 1 msec to commit
the new state.

During this, it executes the routine bond_miimon_inspect() to re-inspect
the state chane and prints the corresponding slave state on to the console.
Hence we do see a message at every 1 msec till the rtnl lock is acquired
and state chage is committed.

This patch doesn't change how bond functions. It only simply limits this
kind of log flood.
Signed-off-by: Praveen Kumar Kannoju <praveen.kannoju@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20240221082752.4660-1-praveen.kannoju@oracle.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Florian Westphal says:

====================
netfilter updates for net-next

1. Prefer KMEM_CACHE() macro to create kmem caches, from Kunwu Chan.

Patches 2 and 3 consolidate nf_log NULL checks and introduces
extra boundary checks on family and type to make it clear that no out
of bounds access will happen.  No in-tree user currently passes such
values, but thats not clear from looking at the function.
From Pablo Neira Ayuso.

Patch 4, also from Pablo, gets rid of unneeded conditional in
nft_osf init function.

Patch 5, from myself, fixes erroneous Kconfig dependencies that
came in an earlier net-next pull request. This should get rid
of the xtables related build failure reports.

Patches 6 to 10 are an update to nftables' concatenated-ranges
set type to speed up element insertions.  This series also
compacts a few data structures and cleans up a few oddities such
as reliance on ZERO_SIZE_PTR when asking to allocate a set with
no elements. From myself.

Patches 11 moves the nf_reinject function from the netfilter core
(vmlinux) into the nfnetlink_queue backend, the only location where
this is called from. Also from myself.

Patch 12, from Kees Cook, switches xtables' compat layer to use
unsafe_memcpy because xt_entry_target cannot easily get converted
to a real flexible array (its UAPI and used inside other structs).

* tag 'nf-next-24-02-21' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
  netfilter: x_tables: Use unsafe_memcpy() for 0-sized destination
  netfilter: move nf_reinject into nfnetlink_queue modules
  netfilter: nft_set_pipapo: use GFP_KERNEL for insertions
  netfilter: nft_set_pipapo: speed up bulk element insertions
  netfilter: nft_set_pipapo: shrink data structures
  netfilter: nft_set_pipapo: do not rely on ZERO_SIZE_PTR
  netfilter: nft_set_pipapo: constify lookup fn args where possible
  netfilter: xtables: fix up kconfig dependencies
  netfilter: nft_osf: simplify init path
  netfilter: nf_log: validate nf_logger_find_get()
  netfilter: nf_log: consolidate check for NULL logger in lookup function
  netfilter: expect: Simplify the allocation of slab caches in nf_conntrack_expect_init
====================

Link: https://lore.kernel.org/r/20240221112637.5396-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

With commit 34d21de9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of this driver.

With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.

Remove the allocation in the ipv6/sit driver and leverage the network
core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240221161732.3026127-1-leitao@debian.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add missing articles.
Fix plural vs. singular.
Fix present vs. future.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sathesh B Edara <sedara@marvell.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b3b97462c3d9eba2ec03dd6d597e63bf49a7365a.1708512706.git.geert+renesas@glider.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There is a spelling mistake in a netif_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220091737.2676984-1-colin.i.king@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix virtual vs physical address confusion. This does not fix a bug
since virtual and physical address spaces are currently the same.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240215080500.2616848-1-agordeev@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

Conflicts:

net/ipv4/udp.c
  f796feab ("udp: add local "peek offset enabled" flag")
  56667da7 ("net: implement lockless setsockopt(SO_PEEK_OFF)")

Adjacent changes:

net/unix/garbage.c
  aa82ac51 ("af_unix: Drop oob_skb ref before purging queue in GC.")
  11498715 ("af_unix: Remove io_uring code for GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2024-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v6.9

The third "new features" pull request for v6.9. This is a quick
followup to send commit 04edb5dc ("wifi: ath12k: Fix uninitialized
use of ret in ath12k_mac_allocate()") to fix the ath12k clang warning
introduced in the previous pull request.

We also have support for QCA2066 in ath11k, several new features in
ath12k and few other changes in drivers. In stack it's mostly cleanup
and refactoring.

Major changes:

ath12k
 * firmware-2.bin support
 * support having multiple identical PCI devices (firmware needs to
   have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
 * QCN9274: support split-PHY devices
 * WCN7850: enable Power Save Mode in station mode
 * WCN7850: P2P support

ath11k:
 * QCA6390 & WCN6855: support 2 concurrent station interfaces
 * QCA2066 support

iwlwifi
 * mvm: support wider-bandwidth OFDMA
 * bump firmware API to 90 for BZ/SC devices

brcmfmac
 * DMI nvram filename quirk for ACEPC W5 Pro

* tag 'wireless-next-2024-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (75 commits)
  wifi: wilc1000: revert reset line logic flip
  wifi: brcmfmac: Add DMI nvram filename quirk for ACEPC W5 Pro
  wifi: rtlwifi: set initial values for unexpected cases of USB endpoint priority
  wifi: rtl8xxxu: check vif before using in rtl8xxxu_tx()
  wifi: rtlwifi: rtl8192cu: Fix TX aggregation
  wifi: wilc1000: remove AKM suite be32 conversion for external auth request
  wifi: nl80211: refactor parsing CSA offsets
  wifi: nl80211: force WLAN_AKM_SUITE_SAE in big endian in NL80211_CMD_EXTERNAL_AUTH
  wifi: iwlwifi: load b0 version of ucode for HR1/HR2
  wifi: iwlwifi: handle per-phy statistics from fw
  wifi: iwlwifi: iwl-fh.h: fix kernel-doc issues
  wifi: iwlwifi: api: fix kernel-doc reference
  wifi: iwlwifi: mvm: unlock mvm if there is no primary link
  wifi: iwlwifi: bump FW API to 90 for BZ/SC devices
  wifi: iwlwifi: mvm: support PHY context version 6
  wifi: iwlwifi: mvm: partially support PHY context version 6
  wifi: iwlwifi: mvm: support wider-bandwidth OFDMA
  wifi: cfg80211: use ML element parsing helpers
  wifi: mac80211: align ieee80211_mle_get_bss_param_ch_cnt()
  wifi: cfg80211: refactor RNR parsing
  ...
====================

Link: https://lore.kernel.org/r/20240222105205.CEC54C433F1@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bpf and netfilter.

  Current release - regressions:

   - af_unix: fix another unix GC hangup

  Previous releases - regressions:

   - core: fix a possible AF_UNIX deadlock

   - bpf: fix NULL pointer dereference in sk_psock_verdict_data_ready()

   - netfilter: nft_flow_offload: release dst in case direct xmit path
     is used

   - bridge: switchdev: ensure MDB events are delivered exactly once

   - l2tp: pass correct message length to ip6_append_data

   - dccp/tcp: unhash sk from ehash for tb2 alloc failure after
     check_estalblished()

   - tls: fixes for record type handling with PEEK

   - devlink: fix possible use-after-free and memory leaks in
     devlink_init()

  Previous releases - always broken:

   - bpf: fix an oops when attempting to read the vsyscall page through
     bpf_probe_read_kernel

   - sched: act_mirred: use the backlog for mirred ingress

   - netfilter: nft_flow_offload: fix dst refcount underflow

   - ipv6: sr: fix possible use-after-free and null-ptr-deref

   - mptcp: fix several data races

   - phonet: take correct lock to peek at the RX queue

  Misc:

   - handful of fixes and reliability improvements for selftests"

* tag 'net-6.8.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
  l2tp: pass correct message length to ip6_append_data
  net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY
  selftests: ioam: refactoring to align with the fix
  Fix write to cloned skb in ipv6_hop_ioam()
  phonet/pep: fix racy skb_queue_empty() use
  phonet: take correct lock to peek at the RX queue
  net: sparx5: Add spinlock for frame transmission from CPU
  net/sched: flower: Add lock protection when remove filter handle
  devlink: fix port dump cmd type
  net: stmmac: Fix EST offset for dwmac 5.10
  tools: ynl: don't leak mcast_groups on init error
  tools: ynl: make sure we always pass yarg to mnl_cb_run
  net: mctp: put sock on tag allocation failure
  netfilter: nf_tables: use kzalloc for hook allocation
  netfilter: nf_tables: register hooks last when adding new chain/flowtable
  netfilter: nft_flow_offload: release dst in case direct xmit path is used
  netfilter: nft_flow_offload: reset dst in route object after setting up flow
  netfilter: nf_tables: set dormant flag on hook register failure
  selftests: tls: add test for peeking past a record of a different type
  selftests: tls: add test for merging of same-type control messages
  ...

Pull tracing fix from Steven Rostedt:

 - While working on the ring buffer I noticed that the counter used for
   knowing where the end of the data is on a sub-buffer was not a full
   "int" but just 20 bits. It was masked out to 0xfffff.

   With the new code that allows the user to change the size of the
   sub-buffer, it is theoretically possible to ask for a size bigger
   than 2^20. If that happens, unexpected results may occur as there's
   no code checking if the counter overflowed the 20 bits of the write
   mask. There are other checks to make sure events fit in the
   sub-buffer, but if the sub-buffer itself is too big, that is not
   checked.

   Add a check in the resize of the sub-buffer to make sure that it
   never goes beyond the size of the counter that holds how much data is
   on it.

* tag 'trace-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  ring-buffer: Do not let subbuf be bigger than write mask

Michael Chan says:

====================
bnxt_en: Ntuple filter improvements

The current Ntuple filter implementation has a limitation on 5750X (P5)
and newer chips.  The destination ring of the ntuple filter must be
a valid ring in the RSS indirection table.  Ntuple filters may not work
if the RSS indirection table is modified by the user to only contain a
subset of the rings.  If an ntuple filter is set to a ring destination
that is not in the RSS indirection table, the packet matching that
filter will be placed in a random ring instead of the specified
destination ring.

This series of patches will fix the problem by using a separate VNIC
for ntuple filters.  The default VNIC will be dedicated for RSS and
so the indirection table can be setup in any way and will not affect
ntuple filters using the separate VNIC.

Quite a bit of refactoring is needed to do the the VNIC and RSS
context accounting in the first few patches.  This is technically a
bug fix, but I think the changes are too big for -net.
====================

Link: https://lore.kernel.org/r/20240220230317.96341-1-michael.chan@broadcom.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The newly created vnic (BNXT_VNIC_NTUPLE) is ready to be used to create
ntuple filters when supported by firmware.  All RX rings can be used
regardless of the RSS indirection setting on the default VNIC.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Allocate and setup the additional VNIC for ntuple filters if this
new method is supported by the firmware.  Even though this VNIC is
only used for ntuple filters with direct ring destinations, we still
setup the RSS hash to be identical to the default VNIC so that each
RX packet will have the correct hash in the RX completion.  This
VNIC is always at VNIC index BNXT_VNIC_NTUPLE.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

On newer chips that support the ring table index method for
ntuple filters, the current scheme of using the same VNIC for
both RSS and ntuple filters will not work in all cases.  An
ntuple filter can only be directed to a destination ring if
that destination ring is also in the RSS indirection table.

To support ntuple filters with any arbitratry RSS indirection
table that may only include a subset of the rings, we need to
use a separate VNIC for ntuple filters.

This patch provisions the additional VNIC.  The next patch will
allocate additional VNIC from firmware and set it up.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Replace hard coded 0 index with more meaningful BNXT_VNIC_DEFAULT.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Refactor bnxt_set_features() function to have a common
function to re-init.  We'll need this to reinitialize when
ntuple configuration changes.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Refactor the code by adding a new function to calculate the number of
required VNICs.  This is used in multiple places when reserving or
checking resources.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_check_rings() is called to check if we have enough resource
assets to satisfy the new number of ethtool channels.  If the asset
test fails, the ethtool operation will fail gracefully.  Otherwise
we will proceed and commit to use the new number of channels.  If it
fails to allocate any resources, the chip will fail to come up.

For completeness, check all possible resources before committing to
the new settings.  Add the missing ring group and RSS context asset
tests in bnxt_check_rings().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add RSS context fields to struct bnxt_hw_rings and struct bnxt_hw_resc.
With these, we can now specific the exact number of RSS contexts to
reserve and store the reserved value.  The original code relies on
other resources to infer the number of RSS contexts to reserve and the
reserved value is not stored.  This improved infrastructure will make
the RSS context accounting more complete and is needed by later
patches.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The current code assumes that every RX ring group and every TX ring
requires a completion ring on P5_PLUS chips.  Now that we have the
bnxt_hw_rings structure, add the cp_p5 field so that it can
be explicitly specified.  This makes the logic more clear.
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The current functions to reserve hardware rings pass in 6 different ring
or resource types as parameters.  Add a structure bnxt_hw_rings to
consolidate all these parameters and pass the structure pointer instead
to these functions.  Add 2 related helper functions also.  This makes
the code cleaner and makes it easier to add new resources to be
reserved.
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Jeremy Kerr says:

====================
MCTP core protocol updates, minor fixes & tests

This series implements some procotol improvements for AF_MCTP,
particularly for systems with multiple MCTP networks defined. For those,
we need to add the network ID to the tag lookups, which then suggests an
updated version of the tag allocate / drop ioctl to allow the net ID to
be specified there too.

The ioctl change affects uabi, so might warrant some extra attention.

There are also a couple of new kunit tests for multiple-net
configurations.

We have a fix for populating the flow data when fragmenting, and a
testcase for that too.

Of course, any queries/comments/etc., please let me know!
====================

Link: https://lore.kernel.org/r/cover.1708335994.git.jk@codeconstruct.com.auSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Ensure we have the correct key parameters on sending a message.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>