The current handler of MMC_BLK_CMD_ERR in mmc_blk_issue_rw_rq function
may cause new coming request permanent missing when the ongoing
request (previoulsy started) complete end.

The problem scenario is as follows:
(1) Request A is ongoing;
(2) Request B arrived, and finally mmc_blk_issue_rw_rq() is called;
(3) Request A encounters the MMC_BLK_CMD_ERR error;
(4) In the error handling of MMC_BLK_CMD_ERR, suppose mmc_blk_cmd_err()
    end request A completed and return zero. Continue the error handling,
    suppose mmc_blk_reset() reset device success;
(5) Continue the execution, while loop completed because variable ret
    is zero now;
(6) Finally, mmc_blk_issue_rw_rq() return without processing request B.

The process related to the missing request may wait that IO request
complete forever, possibly crashing the application or hanging the system.

Fix this issue by starting new request when reset success.
Signed-off-by: Ding Wang <justin.wang@spreadtrum.com>
Fixes: 67716327 ("mmc: block: add eMMC hardware reset support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When dma mapping (dma_map_sg) fails in sdhci_pre_dma_transfer, -EINVAL
is returned. There are 3 callers of sdhci_pre_dma_transfer:
* sdhci_pre_req and sdhci_adma_table_pre: handle negative return
* sdhci_prepare_data: handles 0 (error) and "else" (good) only

sdhci_prepare_data is therefore broken. When it receives -EINVAL from
sdhci_pre_dma_transfer, it assumes 1 sg mapping was mapped. Later,
this non-existent mapping with address 0 is kmap'ped and written to:
Corrupted low memory at ffff880000001000 (1000 phys) = 22b7d67df2f6d1cf
Corrupted low memory at ffff880000001008 (1008 phys) = 63848a5216b7dd95
Corrupted low memory at ffff880000001010 (1010 phys) = 330eb7ddef39e427
Corrupted low memory at ffff880000001018 (1018 phys) = 8017ac7295039bda
Corrupted low memory at ffff880000001020 (1020 phys) = 8ce039eac119074f
...

So teach sdhci_prepare_data to understand negative return values from
sdhci_pre_dma_transfer and disable DMA in that case, as well as for
zero.

It was introduced in 348487cb (mmc:
sdhci: use pipeline mmc requests to improve performance). The commit
seems to be suspicious also by assigning host->sg_count both in
sdhci_pre_dma_transfer and sdhci_adma_table_pre.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org # 4.0+
Fixes: 348487cb
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Change this quirk to apply to AMD Carrizo platform.
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Tested-by: Nath, Arindam <Arindam.Nath@amd.com>
Tested-by: Ramesh, Ramya <Ramya.Ramesh@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Change AMD CZ SMBUS device ID from 0x790b to
use Macro definition
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The KERNCZ is new AMD SB/FCH generation name, like HUDSON2.
0x790b is the device ID for this generation.
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use kernel.h macro definition.

Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Remove module of dw_mmc driver will hung for eMMC devices if we follow the
steps which are listed below,
	insmod dw_mmc.ko
	insmod dw_mmc-pci.ko
	rmmod dw_mmc-pci.ko

The root cause for this issue is, dw_mci_remove() will disable all the
interrupts by programming 0x0 to INTMASK register then it will call
dw_mci_cleanup_slot(). But dw_mci_cleanup_slot() is issuing CMD6 to
disable the eMMC boot partition and it is waiting for Command Complete
interrupt. Since INTMASK was already cleared by dw_mci_remove(), Command
Complete interrupt is not reaching the system. This leads to process hung.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Commit 3a48edc4 ("mmc: sdhci: Use mmc core regulator infrastucture")
changed the behavior for how to assign the ocr_avail mask for the mmc
host. More precisely it started to mask the bits instead of assigning
them.

Restore the behavior, but also make it clear that an OCR mask created
from an external regulator overrides the other ones. The OCR mask is
determined by one of the following with this priority:

1. Supported ranges of external regulator if one supplies VDD
2. Host OCR mask if set by the driver (based on DT properties)
3. The capabilities reported by the controller itself

Fixes: 3a48edc4 ("mmc: sdhci: Use mmc core regulator infrastucture")
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>

MMC_PM_KEEP_POWER doesn't imply MMC_PM_WAKE_SDIO_IRQ, we should only
enable device wake up when MMC_PM_WAKE_SDIO_IRQ is set. And "pm_flags"
is the requested pm features, we should not set it in the host driver.

At the same time, device wakeup is disabled by default, so there's no
need to disable device wakeup explicitly.

This patch fixes the warning as following:

[   64.616651] ------------[ cut here ]------------
[   64.616665] WARNING: CPU: 0 PID: 79 at linux/kernel/irq/manage.c:603 irq_set_irq_wake+0xf0/0x11c()
[   64.616667] Unbalanced IRQ 87 wake disable
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Other subsystem buses attach PM domains during probe, but prior calling
the driver's ->probe() method. During the removal phase, detaching the PM
domain will be done after invoking the driver's ->remove() callback.

Convert the SDIO bus to follow this behavior and add error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since the ->reset() callback is implemented for MMC, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We're currently using a fixed frequency clock specified in the DT, so
enabling is a no-op.  However, the RPi firmware-based clocks driver
can actually disable unused clocks, so when switching to use it we
ended up losing our MMC clock once all devices were probed.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Enable interrupt mode to detect card instead of polling mode
for P1020/P4080/P5020/P5040/T1040 by removing the quirk
SDHCI_QUIRK_BROKEN_CARD_DETECTION. This could improve data
transferring performance and avoid the call trace caused by
polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The iMX6Q/DL can not support HS200 mode while iMX6SL and iMX6SX can,
so introduce a new flag to distinguish them.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The imx6sx usdhc is derived from imx6sl, the difference is minor.
imx6sx have the errata ESDHC_FLAG_ERR004536 fixed.
So introduce a new compatible string for imx6sx to distinguish them.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Using specific compatible string in binding doc to make the binding
more clear.
It's also used to avoid checkpatch warning in the future like follows:
WARNING: DT compatible string "fsl,imx6sx-usdhc" appears un-documented --
check ./Documentation/devicetree/bindings/
+       { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },

total: 0 errors, 1 warnings, 18 lines checked
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The uSDHC has an ADMA Length Mismatch errata ERR004536 which may
cause ADMA work abnormally. The errata has already been fixed for
i.MX6Q TO1.2 and i.MX6DL TO1.1 by enable the bit 7 in 0x6c register.
Unfortunately this fix is not included in i.MX6SL.
So we disable ADMA for i.MX6SL and use SDMA instead.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The usdhc does not have missing card interrupt issue, so don't execute
workaround for usdhc.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In esdhc_writel_le() function, there's duplicated checking of the same
register as follows:
"if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))".
Merge them into one and remove the duplicated one.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Enable detection of HS400 support via capability bit-63
for some Intel host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Implement the select_drive_strength callback to provide
drive strength selection for Intel SPT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a callbak to let host drivers select drive
strength.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.

Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Make a new function out of common code used for drive
strength selection.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Card drive strength selection uses a callback to
which a mask of supported drive strengths is passed.
Currently, the bits are checked against the values
in the SD specifications. That is not necessary
because the callback will anyway match the mask
against a valid value. Simplify by taking the mask
as is but still ensuring that the default mandatory
value (type B) is always supported.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

IO state variable drv_type could be set during card
initialization. Consequently, it must be reset to the
default value when setting the initial state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MMCIF IP on R-Car series has parent clock which can be set several rate,
and it was not implemented on old SH-Mobile series (= SH-Mobile series
parent clock was fixed rate) R-Car series MMCIF can use more high speed
access if it setups parent clock. This patch adds parent clock setup
method. It will be used if DT has "max-frequency", and then, this driver
assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series
(which doesn't boot from DT) and R-Car series (which boots from DT) have
different divider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Silence compiler warning]

Current sh_mmcif driver is using sh_mmcif_xxx and mmcif_xxx
for functions. This patch used sh_mmcif_xxx for all functions.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Current sh_mmcif driver is directly using &host->pd->dev in all place.
It is not big problem, but it is unreadable, and it can be cause of
future bug. This patch adds new sh_mmcif_host_to_dev() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_do_set_ios() doesn't currently program SDHCI_HOST_CONTROL2
register correctly when host->preset_enabled == false.

Add code to handle the missing cases MMC_SET_DRIVER_TYPE_B and
MMC_SET_DRIVER_TYPE_D.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add eSDHC compatible list for P2041/P3041/P4080/P5020/P5040.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use kernel.h macro definition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since the regulator used for the SDMMC IO voltage is not expected to
draw a lot of current, most systems will probably use an inexpensive
LDO for it.  LDO regulators apparently have the feature that they
don't actively drive the voltage down--they wait for other components
in the system to drag the voltage down.  Thus they will transition
faster under heavy loads and slower under light loads.

During an SDMMC voltage change from 3.3V to 1.8V, we are almost
certainly under a light load.  To be specific:
* The regulator is hooked through pulls to CMD0-3 and DAT.  Probably
  the CMD pulls are something like 47K and the DAT is something like
  10K.
* The card is supposed to be driving DAT0-3 low during voltage change
  which will draw _some_ current, but not a lot.
* The regulator is also provided to the SDMMC host controller, but the
  SDMMC host controller is in open drain mode during the voltage
  change and so shouldn't be drawing much current.

In order to keep the SDMMC host working properly (or for noise
reasons), there might also be a capacitor attached to the SDMMC IO
regulator.  This also will have the effect of slowing down transitions
of the regulator, especially under light loads.

From experimental evidence, we've seen the voltage change fail if the
card doesn't detect that the voltage fell to less than about 2.3V when
we turn on the clock.  On one device (that admittedly had a 47K CMD
pullup instead of a 10K CMD pullup) we saw that the voltage was just
about 2.3V after 5ms and thus the voltage change would sometimes fail.
Doubling the delay gave margin and made the voltage change work 100%
of the time, despite the slightly weaker CMD pull.

At the moment submitting this as an RFC patch since my problem _could_
be fixed by increasing the pull strength (or using a smaller
capacitor).  However being a little bit more lenient to strange
hardware could also be a good thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Make the modalias match driver name, this is required to make module
auto-loading work.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
CC: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>