There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.

v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: Deepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <tuexen@fh-muenster.de>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 91ebb929 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941 ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.

Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.

The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: Bug fixes

This series fixes some bugs related to endianess.

Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alan is the original author of the driver. This change was discussed
with the 802.15.4 subsystem maintainer, Alexander Aring.
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices.  As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.

This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.

CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.

This is not generally the case, even if most existing tools do it right.

This patch clamps too long frames as API permits, and issue a one time
error on syslog.

[  394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82

In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added entry for ec_bhf driver.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LECS response contains the MTU that should be used.  Correctly
synchronize with other layers when updating.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

Missing semicolon in range check fix.
Signed-off-by: David S. Miller <davem@davemloft.net>

Vasily Averin says:

====================
cbq: incorrectly low bandwidth blocks limited traffic

v2: patch description changes
Fixes: f0f6ee1f ("cbq: incorrect processing of high limits")

Mainstream commit f0f6ee1f ("cbq: incorrect processing of high limits")
have side effect: if cbq bandwidth setting is less than real interface
throughput non-limited traffic can delay limited traffic for a very long time.

This happen because of q->now changes incorrectly in cbq_dequeue():
in described scenario L2T is much greater than real time delay,
and q->now gets an extra boost for each transmitted packet.

Accumulated boost prevents update q->now, and blocked class can wait
very long time until (q->now >= cl->undertime) will be true again.

More detailed problem description can be found here:
http://www.spinics.net/lists/netdev/msg292493.html

Following patches should fix the problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now q->now_rt is identical to q->now and is not required anymore.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mainstream commit f0f6ee1f ("cbq: incorrect processing of high limits")
have side effect: if cbq bandwidth setting is less than real interface
throughput non-limited traffic can delay limited traffic for a very long time.

This happen because of q->now changes incorrectly in cbq_dequeue():
in described scenario L2T is much greater than real time delay,
and q->now gets an extra boost for each transmitted packet.

Accumulated boost prevents update q->now, and blocked class can wait
very long time until (q->now >= cl->undertime) will be true again.

To fix the problem the patch updates q->now on each cbq_update() call.
L2T-related pre-modification q->now was moved to cbq_update().

My testing confirmed that it fixes the problem and did not discover
any side-effects

Fixes: f0f6ee1f ("cbq: incorrect processing of high limits")
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3b4f302d ("tipc: eliminate
redundant locking") introduced a bug by removing the sanity check
for message importance, allowing programs to assign any value to
the msg_user field. This will mess up the packet reception logic
and may cause random link resets.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the one hand, phy_device.c provides a generic reset function if the phy
driver does not provide a soft_reset pointer. This generic reset does not take
into account the state of the phy, with a potential failure if the phy is in
powerdown mode. On the other hand, smsc driver provides a function with both
correct reset behaviour and configuration.

This patch moves the reset part into a new smsc_phy_reset function and provides
the soft_reset pointer to have a correct reset behaviour by default.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-08-15

This series contains fixes to i40e only.

Anjali provides two fixes for i40e, first adds a check for non-active
VF before sending admin queue messages to the VFS.  This resolves a
potential kernel panic which would happen whenever we got a Tx hang and
there were VFS that were not up or enabled.  The second fix adds
additional checks so that we do try to access a VF that is not up or
enabled which would dereference a null pointer.

Jesse fixes a i40e PTP bug where the hang detection routine was never
being run when PTP was enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

1d023284 ("list: fix order of arguments for
hlist_add_after(_rcu)") was incorrectly rebased on top of
d9124268 ("batman-adv: Fix out-of-order
fragmentation support"). The parameter order change of the rebased patch was
not re-applied as expected. This causes a memory leak and can cause crashes
when out-of-order packets are received. hlist_add_behind will try to access the
uninitalized list pointers of frag_entry_new to find the previous/next entry
and may modify/read random memory locations.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: bcm7xxx internal PHY fixes

Here are 3 small fixes for the Broadcom BCM7xxx internal PHY targeting
suspend/resume issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.

Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>

The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.

Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.

Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>

A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.

Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>

The receive hang detection routine was never being run when
PTP was enabled.

Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.

Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up.  AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.

Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull more ACPI and power management updates from Rafael Wysocki:
 "These are a couple of regression fixes, cpuidle menu governor
  optimizations, fixes for ACPI proccessor and battery drivers,
  hibernation fix to avoid problems related to the e820 memory map,
  fixes for a few cpufreq drivers and a new version of the suspend
  profiling tool analyze_suspend.py.

  Specifics:

   - Fix for an ACPI-based device hotplug regression introduced in 3.14
     that causes a kernel panic to trigger when memory hot-remove is
     attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen

   - Fix for a cpufreq regression introduced in 3.16 that triggers a
     "sleeping function called from invalid context" bug in
     dev_pm_opp_init_cpufreq_table() from Stephen Boyd

   - ACPI battery driver fix for a warning message added in 3.16 that
     prints silly stuff sometimes from Mariusz Ceier

   - Hibernation fix for safer handling of mismatches in the 820 memory
     map between the configurations during image creation and during the
     subsequent restore from Chun-Yi Lee

   - ACPI processor driver fix to handle CPU hotplug notifications
     correctly during system suspend/resume from Lan Tianyu

   - Series of four cpuidle menu governor cleanups that also should
     speed it up a bit from Mel Gorman

   - Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
     cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus
     Pargmann and Uwe Kleine-König

   - Version 3.0 of the analyze_suspend.py suspend profiling tool from
     Todd E Brandt"

* tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / battery: Fix warning message in acpi_battery_get_state()
  PM / tools: analyze_suspend.py: update to v3.0
  cpufreq: arm_big_little: fix module license spec
  cpufreq: speedstep-smi: fix decimal printf specifiers
  ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
  cpufreq: OPP: Avoid sleeping while atomic
  cpufreq: cpu0: Do not print error message when deferring
  cpufreq: integrator: Use set_cpus_allowed_ptr
  PM / hibernate: avoid unsafe pages in e820 reserved regions
  ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
  cpuidle: menu: Lookup CPU runqueues less
  cpuidle: menu: Call nr_iowait_cpu less times
  cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
  cpuidle: menu: Use shifts when calculating averages where possible

Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
 "Part two of the PCI changes for v3.17:

    - Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)

  It's a mechanical change that removes uses of the
  DEFINE_PCI_DEVICE_TABLE macro.  I waited until later in the merge
  window to reduce conflicts, but it's possible you'll still see a few"

* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use

Pull Sparc fixes from David Miller:
 "Hook up the memfd syscall, and properly claim all PCI resources
  discovered when building the PCI device tree"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Hook up memfd_create system call.
  sparc64: Properly claim resources as each PCI bus is probed.
  sparc64: Skip bogus PCI bridge ranges.
  sparc64: Expand PCI bridge probing debug logging.

Pull networking fixes from David Miller:
 "I'm sending this out, in particular, to get the iwlwifi fix
  propagated:

   1) Fix build due to missing include in i40e driver, from Lucas
      Tanure.

   2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.

   3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.

   4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
      Varadhan.

   5) Fix cxgb4i build failures with incompatible Kconfig settings of
      the driver vs ipv6, from Anish Bhatt.

   6) Fix generation of ACK packet timestamps in the presence of TSO
      which will be split up, from Willem de Bruijn.

   7) Don't enable sched scan in iwlwifi driver, it causes firmware
      crashes in some revisions.  From Emmanuel Grumbach.

   8) Revert a macvlan simplification that causes crashes.

   9) Handle RTT calculations properly in the presence of repair'd SKBs,
      from Andrey Vagin.

  10) SIT tunnel lookup uses wrong device index in compares, from
      Shmulik Ladkani.

  11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
      sockets, from Neal Cardwell.

  12) Add missing annotations in rhashtable code, from Thomas Graf.

  13) Fix false interpretation of two RTOs as being from the same TCP
      loss event in the FRTO code, from Neal Cardwell"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
  netlink: Annotate RCU locking for seq_file walker
  rhashtable: fix annotations for rht_for_each_entry_rcu()
  rhashtable: unexport and make rht_obj() static
  rhashtable: RCU annotations for next pointers
  tcp: fix ssthresh and undo for consecutive short FRTO episodes
  tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
  tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
  sit: Fix ipip6_tunnel_lookup device matching criteria
  net: ethernet: ibm: ehea: Remove duplicate object from Makefile
  net: xgene: Check negative return value of xgene_enet_get_ring_size()
  tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
  net: xilinx: Remove .owner field for driver
  Revert "macvlan: simplify the structure port"
  iwlwifi: mvm: disable scheduled scan to prevent firmware crash
  xen-netback: remove loop waiting function
  xen-netback: don't stop dealloc kthread too early
  xen-netback: move NAPI add/remove calls
  xen-netback: fix debugfs entry creation
  xen-netback: fix debugfs write length check
  net-timestamp: fix missing tcp fragmentation cases
  ...

John W. Linville says:

====================
pull request: wireless 2014-08-14

Please pull this batch of fixes intended for the 3.17 stream...

Arend van Spriel brings two brcmfmac fixes, one which fixes a memory
leak and one which corrects some merge damage.

Emmanuel Grumbach fixes Linus's iwlwifi firmware-related log spam.

Rickard Strandqvist does some proper NULL termination after a call
to strncpy.

Ronald Wahl corrects a carl9170 problem with sending URBs with the
wrong endpoint type (resulting in log spam).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Silences the following sparse warnings:
net/netlink/af_netlink.c:2926:21: warning: context imbalance in 'netlink_seq_start' - wrong count at exit
net/netlink/af_netlink.c:2972:13: warning: context imbalance in 'netlink_seq_stop' - unexpected unlock
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call rcu_deference_raw() directly from within rht_for_each_entry_rcu()
as list_for_each_entry_rcu() does.

Fixes the following sparse warnings:
net/netlink/af_netlink.c:2906:25:    expected struct rhash_head const *__mptr
net/netlink/af_netlink.c:2906:25:    got struct rhash_head [noderef] <asn:4>*<noident>

Fixes: e341694e ("netlink: Convert netlink_lookup() to use RCU protected hash table")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to export rht_obj(), all inner to outer object translations
occur internally. It was intended to be used with rht_for_each() which
now primarily serves as the iterator for rhashtable_remove_pprev() to
effectively flush and free the full table.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Properly annotate next pointers as access is RCU protected in
the lookup path.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix TCP FRTO logic so that it always notices when snd_una advances,
indicating that any RTO after that point will be a new and distinct
loss episode.

Previously there was a very specific sequence that could cause FRTO to
fail to notice a new loss episode had started:

(1) RTO timer fires, enter FRTO and retransmit packet 1 in write queue
(2) receiver ACKs packet 1
(3) FRTO sends 2 more packets
(4) RTO timer fires again (should start a new loss episode)

The problem was in step (3) above, where tcp_process_loss() returned
early (in the spot marked "Step 2.b"), so that it never got to the
logic to clear icsk_retransmits. Thus icsk_retransmits stayed
non-zero. Thus in step (4) tcp_enter_loss() would see the non-zero
icsk_retransmits, decide that this RTO is not a new episode, and
decide not to cut ssthresh and remember the current cwnd and ssthresh
for undo.

There were two main consequences to the bug that we have
observed. First, ssthresh was not decreased in step (4). Second, when
there was a series of such FRTO (1-4) sequences that happened to be
followed by an FRTO undo, we would restore the cwnd and ssthresh from
before the entire series started (instead of the cwnd and ssthresh
from before the most recent RTO). This could result in cwnd and
ssthresh being restored to values much bigger than the proper values.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Fixes: e33099f9 ("tcp: implement RFC5682 F-RTO")
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_tw_recycle heavily relies on tcp timestamps to build a per-host
ordering of incoming connections and teardowns without the need to
hold state on a specific quadruple for TCP_TIMEWAIT_LEN, but only for
the last measured RTO. To do so, we keep the last seen timestamp in a
per-host indexed data structure and verify if the incoming timestamp
in a connection request is strictly greater than the saved one during
last connection teardown. Thus we can verify later on that no old data
packets will be accepted by the new connection.

During moving a socket to time-wait state we already verify if timestamps
where seen on a connection. Only if that was the case we let the
time-wait socket expire after the RTO, otherwise normal TCP_TIMEWAIT_LEN
will be used. But we don't verify this on incoming SYN packets. If a
connection teardown was less than TCP_PAWS_MSL seconds in the past we
cannot guarantee to not accept data packets from an old connection if
no timestamps are present. We should drop this SYN packet. This patch
closes this loophole.

Please note, this patch does not make tcp_tw_recycle in any way more
usable but only adds another safety check:
Sporadic drops of SYN packets because of reordering in the network or
in the socket backlog queues can happen. Users behing NAT trying to
connect to a tcp_tw_recycle enabled server can get caught in blackholes
and their connection requests may regullary get dropped because hosts
behind an address translator don't have synchronized tcp timestamp clocks.
tcp_tw_recycle cannot work if peers don't have tcp timestamps enabled.

In general, use of tcp_tw_recycle is disadvised.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we use the correct address-family-specific function for
handling MTU reductions from within tcp_release_cb().

Previously AF_INET6 sockets were incorrectly always using the IPv6
code path when sometimes they were handling IPv4 traffic and thus had
an IPv4 dst.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Willem de Bruijn <willemb@google.com>
Fixes: 563d34d0 ("tcp: dont drop MTU reduction indications")
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of 4fddbf5d ("sit: strictly restrict incoming traffic to tunnel link device"),
when looking up a tunnel, tunnel's underlying interface (t->parms.link)
is verified to match incoming traffic's ingress device.

However the comparison was incorrectly based on skb->dev->iflink.

Instead, dev->ifindex should be used, which correctly represents the
interface from which the IP stack hands the ipip6 packets.

This allows setting up sit tunnels bound to vlan interfaces (otherwise
incoming ipip6 traffic on the vlan interface was dropped due to
ipip6_tunnel_lookup match failure).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>