Make MTU configurable on KSZ87xx and KSZ88xx series of switches.

Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532

Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.

With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.

This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The np needs to be released through of_node_put() in the error handling
path of mtk_wed_wo_hardware_init().

Fixes: 79968444 ("net: ethernet: mtk_wed: introduce wed wo support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221205034339.112163-1-yuancan@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This patch adds reset parameter to mtk_wed_rx_ring_setup signature
in order to align rx_ring_setup callback to tx_ring_setup one introduced
in 'commit 23dca7a9 ("net: ethernet: mtk_wed: add reset to
tx_ring_setup callback")'
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/29c6e7a5469e784406cf3e2920351d1207713d05.1670239984.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Semicolons after "}" are not needed.
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/202212051422158113766@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/202212051021451139126@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We currently have some complicated code in sfp_probe() which gets the
I2C bus depending on whether the sfp node is DT or ACPI, and we use
completely separate lookup functions.

This could do with being in a separate function to make the code more
readable, so move it to a new function, sfp_i2c_get(). We can also use
fwnode_find_reference() to lookup the I2C bus fwnode before then
decending into fwnode-type specific parsing.

A future cleanup would be to move the fwnode-type specific parsing into
the i2c layer, which is where it really should be.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1p1WGJ-0098wS-4w@rmk-PC.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The memcpy() in ncsi_cmd_handler_oem deserializes nca->data into a
flexible array structure that overlapping with non-flex-array members
(mfr_id) intentionally. Since the mem_to_flex() API is not finished,
temporarily silence this warning, since it is a false positive, using
unsafe_memcpy().
Reported-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/netdev/CACPK8Xdfi=OJKP0x0D1w87fQeFZ4A2DP2qzGCRcuVbpU-9=4sQ@mail.gmail.com/
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221202212418.never.837-kees@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Horatiu Vultur says:

====================
net: lan966x: Enable PTP on bridge interfaces

Before it was not allowed to run ptp on ports that are part of a bridge
because in case of transparent clock the HW will still forward the frames
so there would be duplicate frames.
Now that there is VCAP support, it is possible to add entries in the VCAP
to trap frames to the CPU and the CPU will forward these frames.
The first part of the patch series, extends the VCAP support to be able to
modify and get the rule, while the last patch uses the VCAP to trap the ptp
frames.
====================

Link: https://lore.kernel.org/r/20221203104348.1749811-1-horatiu.vultur@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Currently lan966x, doesn't allow to run PTP over interfaces that are
part of the bridge. The reason is when the lan966x was receiving a
PTP frame (regardless if L2/IPv4/IPv6) the HW it would flood this
frame.
Now that it is possible to add VCAP rules to the HW, such to trap these
frames to the CPU, it is possible to run PTP also over interfaces that
are part of the bridge.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add the function vcap_rule_get_key_u32 which allows to get the value and
the mask of a key that exist on the rule. If the key doesn't exist,
it would return error.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add the function vcap_mod_rule which allows to update an existing rule
in the vcap. It is required for the rule to exist in the vcap to be able
to modify it.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add function vcap_get_rule which returns a rule based on the internal
rule id.
The entire functionality of reading and decoding the rule from the VCAP
was inside vcap_api_debugfs file. So move the entire implementation in
vcap_api as this is used also by vcap_get_rule.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Since Wireless Ethernet Dispatcher is now available for mt7986 in mt76,
enable hw flow support for MT7986 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/fdcaacd827938e6a8c4aa1ac2c13e46d2c08c821.1670072898.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add netlink based support for "ethtool -x <dev> [context x]"
command by implementing ETHTOOL_MSG_RSS_GET netlink message.
This is equivalent to functionality provided via ETHTOOL_GRSSH
in ioctl path. It sends RSS table, hash key and hash function
of an interface to user space.

This patch implements existing functionality available
in ioctl path and enables addition of new RSS context
based parameters in future.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Link: https://lore.kernel.org/r/20221202002555.241580-1-sudheer.mogilappagari@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Rename the temperature sensors macros to match the names in the
datasheet.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rewrite nfp_net_set_rx_mode() to implement interface to delivery
mc address and operations to firmware by using general mailbox
for filtering multicast packets.

The operations include add mc address and delete mc address.
And the limitation of mc addresses number is 1024 for each net
device.

User triggers adding mc address by using command below:
ip maddress add <mc address> dev <interface name>

User triggers deleting mc address by using command below:
ip maddress del <mc address> dev <interface name>
Signed-off-by: Diana Wang <na.wang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-next-20221201-b' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Increasing SACK size and moving away from softirq, parts 2 & 3

Here are the second and third parts of patches in the process of moving
rxrpc from doing a lot of its stuff in softirq context to doing it in an
I/O thread in process context and thereby making it easier to support a
larger SACK table.

The full description is in the description for the first part[1] which is
already in net-next.

The second part includes some cleanups, adds some testing and overhauls
some tracing:

 (1) Remove declaration of rxrpc_kernel_call_is_complete() as the
     definition is no longer present.

 (2) Remove the knet() and kproto() macros in favour of using tracepoints.

 (3) Remove handling of duplicate packets from recvmsg.  The input side
     isn't now going to insert overlapping/duplicate packets into the
     recvmsg queue.

 (4) Don't use the rxrpc_conn_parameters struct in the rxrpc_connection or
     rxrpc_bundle structs - rather put the members in directly.

 (5) Extract the abort code from a received abort packet right up front
     rather than doing it in multiple places later.

 (6) Use enums and symbol lists rather than __builtin_return_address() to
     indicate where a tracepoint was triggered for local, peer, conn, call
     and skbuff tracing.

 (7) Add a refcount tracepoint for the rxrpc_bundle struct.

 (8) Implement an in-kernel server for the AFS rxperf testing program to
     talk to (enabled by a Kconfig option).

This is tagged as rxrpc-next-20221201-a.

The third part introduces the I/O thread and switches various bits over to
running there:

 (1) Fix call timers and call and connection workqueues to not hold refs on
     the rxrpc_call and rxrpc_connection structs to thereby avoid messy
     cleanup when the last ref is put in softirq mode.

 (2) Split input.c so that the call packet processing bits are separate
     from the received packet distribution bits.  Call packet processing
     gets bumped over to the call event handler.

 (3) Create a per-local endpoint I/O thread.  Barring some tiny bits that
     still get done in softirq context, all packet reception, processing
     and transmission is done in this thread.  That will allow a load of
     locking to be removed.

 (4) Perform packet processing and error processing from the I/O thread.

 (5) Provide a mechanism to process call event notifications in the I/O
     thread rather than queuing a work item for that call.

 (6) Move data and ACK transmission into the I/O thread.  ACKs can then be
     transmitted at the point they're generated rather than getting
     delegated from softirq context to some process context somewhere.

 (7) Move call and local processor event handling into the I/O thread.

 (8) Move cwnd degradation to after packets have been transmitted so that
     they don't shorten the window too quickly.

A bunch of simplifications can then be done:

 (1) The input_lock is no longer necessary as exclusion is achieved by
     running the code in the I/O thread only.

 (2) Don't need to use sk->sk_receive_queue.lock to guard socket state
     changes as the socket mutex should suffice.

 (3) Don't take spinlocks in RCU callback functions as they get run in
     softirq context and thus need _bh annotations.

 (4) RCU is then no longer needed for the peer's error_targets list.

 (5) Simplify the skbuff handling in the receive path by dropping the ref
     in the basic I/O thread loop and getting an extra ref as and when we
     need to queue the packet for recvmsg or another context.

 (6) Get the peer address earlier in the input process and pass it to the
     users so that we only do it once.

This is tagged as rxrpc-next-20221201-b.

Changes:
========
ver #2)
 - Added a patch to change four assertions into warnings in rxrpc_read()
   and fixed a checker warning from a __user annotation that should have
   been removed..
 - Change a min() to min_t() in rxperf as PAGE_SIZE doesn't seem to match
   type size_t on i386.
 - Three error handling issues in rxrpc_new_incoming_call():
   - If not DATA or not seq #1, should drop the packet, not abort.
   - Fix a goto that went to the wrong place, dropping a non-held lock.
   - Fix an rcu_read_lock that should've been an unlock.
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: kafs-testing+fedora36_64checkkafs-build-144@auristor.com
Link: https://lore.kernel.org/r/166794587113.2389296.16484814996876530222.stgit@warthog.procyon.org.uk/ [1]
Link: https://lore.kernel.org/r/166982725699.621383.2358362793992993374.stgit@warthog.procyon.org.uk/ # v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the Multi-Gigabit Ethernet (MGBE/XPCS) IP found on
NVIDIA Tegra234 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Co-developed-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Tegra MGBE ethernet controller requires that the SERDES link is
powered-up after the PHY link is up, otherwise the link fails to
become ready following a resume from suspend. Add a variable to indicate
that the SERDES link must be powered-up after the PHY link.
Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: add and use netdev_sw_irq_coalesce_default_on()

There are reports about r8169 not reaching full line speed on certain
systems (e.g. SBC's) with a 2.5Gbps link.
There was a time when hardware interrupt coalescing was enabled per
default, but this was changed due to ASPM-related issues on few systems.

Meanwhile we have sysfs attributes for controlling kind of
"software interrupt coalescing" on the GRO level. However most distros
and users don't know about it. So lets set a conservative default for
both involved parameters. Users can still override the defaults via
sysfs. Don't enable these settings on the fast ethernet chip versions,
they are slow enough.

Even with these conservative setting interrupt load on my 1Gbps test
system reduced significantly.

Follow Jakub's suggestion and put this functionality into net core
so that other MAC drivers can reuse it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are reports about r8169 not reaching full line speed on certain
systems (e.g. SBC's) with a 2.5Gbps link.
There was a time when hardware interrupt coalescing was enabled per
default, but this was changed due to ASPM-related issues on few systems.
So let's use software interrupt coalescing instead and enable it
using new function netdev_sw_irq_coalesce_default_on().

Even with these conservative settings interrupt load on my 1Gbps test
system reduced significantly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper for drivers wanting to set SW IRQ coalescing
by default. The related sysfs attributes can be used to
override the default values.

Follow Jakub's suggestion and put this functionality into
net core so that drivers wanting to use software interrupt
coalescing per default don't have to open-code it.

Note that this function needs to be called before the
netdevice is registered.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to fix the following sleep while atomic bug always alloc pages
with GFP_ATOMIC in mtk_wed_wo_queue_refill since page_frag_alloc runs in
spin_lock critical section.

[    9.049719] Hardware name: MediaTek MT7986a RFB (DT)
[    9.054665] Call trace:
[    9.057096]  dump_backtrace+0x0/0x154
[    9.060751]  show_stack+0x14/0x1c
[    9.064052]  dump_stack_lvl+0x64/0x7c
[    9.067702]  dump_stack+0x14/0x2c
[    9.071001]  ___might_sleep+0xec/0x120
[    9.074736]  __might_sleep+0x4c/0x9c
[    9.078296]  __alloc_pages+0x184/0x2e4
[    9.082030]  page_frag_alloc_align+0x98/0x1ac
[    9.086369]  mtk_wed_wo_queue_refill+0x134/0x234
[    9.090974]  mtk_wed_wo_init+0x174/0x2c0
[    9.094881]  mtk_wed_attach+0x7c8/0x7e0
[    9.098701]  mt7915_mmio_wed_init+0x1f0/0x3a0 [mt7915e]
[    9.103940]  mt7915_pci_probe+0xec/0x3bc [mt7915e]
[    9.108727]  pci_device_probe+0xac/0x13c
[    9.112638]  really_probe.part.0+0x98/0x2f4
[    9.116807]  __driver_probe_device+0x94/0x13c
[    9.121147]  driver_probe_device+0x40/0x114
[    9.125314]  __driver_attach+0x7c/0x180
[    9.129133]  bus_for_each_dev+0x5c/0x90
[    9.132953]  driver_attach+0x20/0x2c
[    9.136513]  bus_add_driver+0x104/0x1fc
[    9.140333]  driver_register+0x74/0x120
[    9.144153]  __pci_register_driver+0x40/0x50
[    9.148407]  mt7915_init+0x5c/0x1000 [mt7915e]
[    9.152848]  do_one_initcall+0x40/0x25c
[    9.156669]  do_init_module+0x44/0x230
[    9.160403]  load_module+0x1f30/0x2750
[    9.164135]  __do_sys_init_module+0x150/0x200
[    9.168475]  __arm64_sys_init_module+0x18/0x20
[    9.172901]  invoke_syscall.constprop.0+0x4c/0xe0
[    9.177589]  do_el0_svc+0x48/0xe0
[    9.180889]  el0_svc+0x14/0x50
[    9.183929]  el0t_64_sync_handler+0x9c/0x120
[    9.188183]  el0t_64_sync+0x158/0x15c

Fixes: 79968444 ("net: ethernet: mtk_wed: introduce wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/67ca94bdd3d9eaeb86e52b3050fbca0bcf7bb02f.1669908312.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

kfree_rcu(1-arg) should be avoided as much as possible,
since this is only possible from sleepable contexts,
and incurr extra rcu barriers.

I wish the 1-arg variant of kfree_rcu() would
get a distinct name, like kfree_rcu_slow()
to avoid it being abused.

Fixes: 459837b5 ("net/tcp: Disable TCP-MD5 static key on tcp_md5sig_info destruction")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20221202052847.2623997-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v6.2

Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.

Major changes:

ath10k
 - store WLAN firmware version in SMEM image table

mt76
 - mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
 - mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
 - mt7915: add ack signal support
 - mt7915: enable coredump support
 - mt7921: remain_on_channel support
 - mt7921: channel context support

iwlwifi
 - enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
 - 320 MHz channels support

* tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (144 commits)
  wifi: ath10k: fix QCOM_SMEM dependency
  wifi: mt76: mt7921e: add pci .shutdown() support
  wifi: mt76: mt7915: mmio: fix naming convention
  wifi: mt76: mt7996: add support to configure spatial reuse parameter set
  wifi: mt76: mt7996: enable ack signal support
  wifi: mt76: mt7996: enable use_cts_prot support
  wifi: mt76: mt7915: rely on band_idx of mt76_phy
  wifi: mt76: mt7915: enable per bandwidth power limit support
  wifi: mt76: mt7915: introduce mt7915_get_power_bound()
  mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
  wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
  wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
  wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
  wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
  wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
  wifi: mt76: mt7915: fix band_idx usage
  wifi: mt76: mt7915: enable .sta_set_txpwr support
  wifi: mt76: mt7915: add basedband Txpower info into debugfs
  wifi: mt76: mt7915: add support to configure spatial reuse parameter set
  wifi: mt76: mt7915: add missing MODULE_PARM_DESC
  ...
====================

Link: https://lore.kernel.org/r/20221202214254.D0D3DC433C1@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Nathan noticed that when HWSPINLOCK is disabled there's a Kconfig warning:

  WARNING: unmet direct dependencies detected for QCOM_SMEM
    Depends on [n]: (ARCH_QCOM [=y] || COMPILE_TEST [=n]) && HWSPINLOCK [=n]
    Selected by [m]:
    - ATH10K_SNOC [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && ATH10K [=m] && (ARCH_QCOM [=y] || COMPILE_TEST [=n])

The problem here is that QCOM_SMEM depends on HWSPINLOCK so we cannot select
QCOM_SMEM and instead we neeed to use 'depends on'.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/Y4YsyaIW+CPdHWv3@dev-arch.thelio-3990X/
Fixes: 4d79f6f3 ("wifi: ath10k: Store WLAN firmware version in SMEM image table")
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202103027.25974-1-kvalo@kernel.org

Refill RX queue in batches of descriptors to improve performance. Refill
is allowed to fail as long as a minimum number of descriptors is active.
Thus, a limited number of failed RX buffer allocations is now allowed
for normal operation. Previously every failed allocation resulted in a
dropped frame.

If the minimum number of active descriptors is reached, then RX buffers
are still reused and frames are dropped. This ensures that the RX queue
never runs empty and always continues to operate.

Prework for future XDP support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without interrupt throttling, iperf server mode generates a CPU load of
100% (A53 1.2GHz). Also the throughput suffers with less than 900Mbit/s
on a 1Gbit/s link. The reason is a high interrupt load with interrupts
every ~20us.

Reduce interrupt load by throttling of interrupts. Interrupt delay
default is 64us. For iperf server mode the CPU load is significantly
reduced to ~20% and the throughput reaches the maximum of 941MBit/s.
Interrupts are generated every ~140us.

RX and TX coalesce can be configured with ethtool. RX coalesce has
priority over TX coalesce if the same interrupt is used.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow user space to read number of TX and RX queue. This is useful for
device dependent qdisc configurations like TAPRIO with hardware offload.
Also ethtool::get_per_queue_coalesce / set_per_queue_coalesce requires
that interface.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct xmit hash steps for layer3+4 as introduced by commit
49aefd13 ("bonding: do not discard lowest hash bit for non layer3+4
hashing").
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit c1f897ce ("bonding: set default miimon value for non-arp
modes if not set") the miimon default was changed from zero to 100 if
arp_interval is also zero. Document this fact in bonding.rst.

Fixes: c1f897ce ("bonding: set default miimon value for non-arp modes if not set")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The main usage of the struct thunderbolt_ip_frame_header is to handle
the packets on the media layer. The header is bound to the protocol
in which the byte ordering is crucial. However the data type definition
doesn't use that and sparse is unhappy, for example (17 altogether):

  .../thunderbolt.c:718:23: warning: cast to restricted __le32

  .../thunderbolt.c:966:42: warning: incorrect type in assignment (different base types)
  .../thunderbolt.c:966:42:    expected unsigned int [usertype] frame_count
  .../thunderbolt.c:966:42:    got restricted __le32 [usertype]

Switch to the bitwise types in the struct thunderbolt_ip_frame_header to
reduce this, but not completely solving (9 left), because the same data
type is used for Rx header handled locally (in CPU byte order).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less heavier for builds
than the use of __maybe_unused attributes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devlink instances may contain thousands of ports. Storing them in
linked list and looking them up is not scalable. Convert the linked list
into xarray.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sebastian Andrzej Siewior says:

====================
I started playing with HSR and run into a problem. Tested latest
upstream -rc and noticed more problems. Now it appears to work.
For testing I have a small three node setup with iperf and ping. While
iperf doesn't complain ping reports missing packets and duplicates.
====================

Link: https://lore.kernel.org/r/20221129164815.128922-1-bigeasy@linutronix.de/Signed-off-by: Jakub Kicinski <kuba@kernel.org>