Merge tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes

Fixes for omaps for v5.11-rc cycle

The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:

- The omap_prm reset driver needs to clear any reset bits deasserted by
  the bootloader or kexec boot for the three reset bit cases. Otherwise
  we can have an oops with accelerators starting to boot with potentially
  unconfigured MMU for example

- Custom kernel configs are not automatically selecting simple-pm-bus
  driver that we now need to probe interconnects so we need to select it
  always

- We are not passing legacy platform data in auxdata with simple-pm-bus
  like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
  it can pass it to of_platform_populate()

Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places

And then we have few device specific fixes:

- We need to remove legacy spi-cs-hig for gta04 display to work, and
  set the gpio to active low

- Omap1 specific ohci-omap needs to call gpio_free()

- Droid4 needs to use padconf interrupt for the slider as the edge
  gpio interrupts may be lost for deeper idle states

* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts; gta04: SPI panel chip select is active low
  soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
  ARM: OMAP1: OSK: fix ohci-omap breakage
  DTS: ARM: gta04: remove legacy spi-cs-high to make display work again

Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-arm64-defconfig-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes

Qualcomm ARM64 defconfig fixes for v5.11

Devicetree patches for SDM845 introduced in v5.11 requires the
platform's interconnect driver to be buildin, or the kernel will fail to
provide a valid console when we hit userspace.

* tag 'qcom-arm64-defconfig-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  arm64: defconfig: Make INTERCONNECT_QCOM_SDM845 builtin

Link: https://lore.kernel.org/r/20210125232412.642834-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-arm64-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes

Qualcomm ARM64 fixes for 5.11

This fixes a regression in Lenovo Yoga C630, where the touchpad in some
units stopped working, by re-enabling the "tsc2" device.

It also marks the LPASS related clocks as protected to allow DB845c and
the Lenovo Yoga C630 to boot even if CONFIG_SDM_LPASSCC_845 is enabled.

* tag 'qcom-arm64-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
  arm64: dts: qcom: c630: keep both touchpad devices enabled

Link: https://lore.kernel.org/r/20210125232039.642565-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes

arm64: dts: amlogic: fixes for v5.11-rc
- meson-g12: Set FL-adj property value

* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: amlogic: meson-g12: Set FL-adj property value

Link: https://lore.kernel.org/r/7hk0s0x3im.fsf@baylibre.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'stm32-dt-for-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes

STM32 DT fixes for v5.11, round 1

Highlights:
-----------

 -Fixes are for DHCOM/DHCOR boards:
  - Fix DRC02 uSD card detect polarity
  - use uSD card detect on DHCOM
  - Disable uSD WP on DHCOM
  - Disable TSC2004 on DRC02
  - Fix GPIO hogs on DHCOM boards

* tag 'stm32-dt-for-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect

Link: https://lore.kernel.org/r/b7379980-857e-736a-85d8-58e2bd300141@foss.st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

We may lose edge interrupts for gpio banks other than the first gpio
bank as they are not always powered. Instead, we must use the padconf
interrupt as that is always powered.

Note that we still also use the gpio for reading the pin state as that
can't be done with the padconf device.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'imx-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.11, round 2:

- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.

* tag 'imx-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  firmware: imx: select SOC_BUS to fix firmware build
  arm64: dts: imx8mp: Correct the gpio ranges of gpio3
  ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
  ARM: imx: build suspend-imx6.S with arm instruction set
  ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset

Link: https://lore.kernel.org/r/20210119091949.GD4356@dragonSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Change the bcm2835 maintainer info in order to handle subsequent SoCs.
After this get_maintainers.pl provides the proper maintainers for
irqchip-bcm2836.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add a non-empty dma-ranges so that DMA address translation happens.

Fixes: 2013a4b6 ("arm64: dts: broadcom: clear the warnings caused by empty dma-ranges")
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

of_match_node() calls __of_match_node() which loops though the entries of
matches array. It stops when condition:
(matches->name[0] || matches->type[0] || matches->compatible[0]) is
false. Thus, add a null entry at the end of at91_soc_allowed_list[]
array.

Fixes: caab13b4 ("drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs")
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Since at91_soc_init is called unconditionally from atmel_soc_device_init,
we get the following warning on all non AT91 SoCs:
	" AT91: Could not find identification node"

Fix the same by filtering with allowed AT91 SoC list.

Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201211135846.1334322-1-sudeep.holla@arm.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'optee-rcu-sched-trace-for-v5.11' of git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes

Fix rcu_sched trace from OP-TEE invoke

Replaces might_sleep() with a conditional call to cond_resched()
in order to avoid the rcu_sched trace in some corner cases.

* tag 'optee-rcu-sched-trace-for-v5.11' of git://git.linaro.org/people/jens.wiklander/linux-tee:
  tee: optee: replace might_sleep with cond_resched

Link: https://lore.kernel.org/r/20210122074234.GA1074747@jadeSigned-off-by: Arnd Bergmann <arnd@arndb.de>

might_sleep() is a debugging aid and triggers rescheduling only for
certain kernel configurations. Replace with an explicit check and
reschedule to work for all kernel configurations. Fixes the following
trace:

  [  572.945146] rcu: INFO: rcu_sched self-detected stall on CPU
  [  572.949275] rcu:     0-....: (2099 ticks this GP) idle=572/1/0x40000002 softirq=7412/7412 fqs=974
  [  572.957964]  (t=2100 jiffies g=10393 q=21)
  [  572.962054] NMI backtrace for cpu 0
  [  572.965540] CPU: 0 PID: 165 Comm: xtest Not tainted 5.8.7 #1
  [  572.971188] Hardware name: STM32 (Device Tree Support)
  [  572.976354] [<c011163c>] (unwind_backtrace) from [<c010b7f8>] (show_stack+0x10/0x14)
  [  572.984080] [<c010b7f8>] (show_stack) from [<c0511e4c>] (dump_stack+0xc4/0xd8)
  [  572.991300] [<c0511e4c>] (dump_stack) from [<c0519abc>] (nmi_cpu_backtrace+0x90/0xc4)
  [  572.999130] [<c0519abc>] (nmi_cpu_backtrace) from [<c0519bdc>] (nmi_trigger_cpumask_backtrace+0xec/0x130)
  [  573.008706] [<c0519bdc>] (nmi_trigger_cpumask_backtrace) from [<c01a5184>] (rcu_dump_cpu_stacks+0xe8/0x110)
  [  573.018453] [<c01a5184>] (rcu_dump_cpu_stacks) from [<c01a4234>] (rcu_sched_clock_irq+0x7fc/0xa88)
  [  573.027416] [<c01a4234>] (rcu_sched_clock_irq) from [<c01acdd0>] (update_process_times+0x30/0x8c)
  [  573.036291] [<c01acdd0>] (update_process_times) from [<c01bfb90>] (tick_sched_timer+0x4c/0xa8)
  [  573.044905] [<c01bfb90>] (tick_sched_timer) from [<c01adcc8>] (__hrtimer_run_queues+0x174/0x358)
  [  573.053696] [<c01adcc8>] (__hrtimer_run_queues) from [<c01aea2c>] (hrtimer_interrupt+0x118/0x2bc)
  [  573.062573] [<c01aea2c>] (hrtimer_interrupt) from [<c09ad664>] (arch_timer_handler_virt+0x28/0x30)
  [  573.071536] [<c09ad664>] (arch_timer_handler_virt) from [<c0190f50>] (handle_percpu_devid_irq+0x8c/0x240)
  [  573.081109] [<c0190f50>] (handle_percpu_devid_irq) from [<c018ab8c>] (generic_handle_irq+0x34/0x44)
  [  573.090156] [<c018ab8c>] (generic_handle_irq) from [<c018b194>] (__handle_domain_irq+0x5c/0xb0)
  [  573.098857] [<c018b194>] (__handle_domain_irq) from [<c052ac50>] (gic_handle_irq+0x4c/0x90)
  [  573.107209] [<c052ac50>] (gic_handle_irq) from [<c0100b0c>] (__irq_svc+0x6c/0x90)
  [  573.114682] Exception stack(0xd90dfcf8 to 0xd90dfd40)
  [  573.119732] fce0:                                                       ffff0004 00000000
  [  573.127917] fd00: 00000000 00000000 00000000 00000000 00000000 00000000 d93493cc ffff0000
  [  573.136098] fd20: d2bc39c0 be926998 d90dfd58 d90dfd48 c09f3384 c01151f0 400d0013 ffffffff
  [  573.144281] [<c0100b0c>] (__irq_svc) from [<c01151f0>] (__arm_smccc_smc+0x10/0x20)
  [  573.151854] [<c01151f0>] (__arm_smccc_smc) from [<c09f3384>] (optee_smccc_smc+0x3c/0x44)
  [  573.159948] [<c09f3384>] (optee_smccc_smc) from [<c09f4170>] (optee_do_call_with_arg+0xb8/0x154)
  [  573.168735] [<c09f4170>] (optee_do_call_with_arg) from [<c09f4638>] (optee_invoke_func+0x110/0x190)
  [  573.177786] [<c09f4638>] (optee_invoke_func) from [<c09f1ebc>] (tee_ioctl+0x10b8/0x11c0)
  [  573.185879] [<c09f1ebc>] (tee_ioctl) from [<c029f62c>] (ksys_ioctl+0xe0/0xa4c)
  [  573.193101] [<c029f62c>] (ksys_ioctl) from [<c0100060>] (ret_fast_syscall+0x0/0x54)
  [  573.200750] Exception stack(0xd90dffa8 to 0xd90dfff0)
  [  573.205803] ffa0:                   be926bf4 be926a78 00000003 8010a403 be926908 004e3cf8
  [  573.213987] ffc0: be926bf4 be926a78 00000000 00000036 be926908 be926918 be9269b0 bffdf0f8
  [  573.222162] ffe0: b6d76fb0 be9268fc b6d66621 b6c7e0d8

seen on STM32 DK2 with CONFIG_PREEMPT_NONE.

Fixes: 9f02b8f6 ("tee: optee: add might_sleep for RPC requests")
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
[jw: added fixes tag + small adjustments in the code]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>

Fix build error in firmware/imx/ selecting SOC_BUS.

riscv32-linux-ld: drivers/firmware/imx/imx-scu-soc.o: in function `.L9':
imx-scu-soc.c:(.text+0x1b0): undefined reference to `soc_device_register'

Fixes: edbee095 ("firmware: imx: add SCU firmware driver support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On i.MX8MP, The GPIO3's secondary gpio-ranges's 'gpio controller offset'
cell value should be 26, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Fixes: 6d9b8d20 ("arm64: dts: freescale: Add i.MX8MP dtsi support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.

If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.

Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.

Fixes: 86b08bd5 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

When the kernel is configured to use the Thumb-2 instruction set
"suspend-to-memory" fails to resume. Observed on a Colibri iMX6ULL
(i.MX 6ULL) and Apalis iMX6 (i.MX 6Q).

It looks like the CPU resumes unconditionally in ARM instruction mode
and then chokes on the presented Thumb-2 code it should execute.

Fix this by using the arm instruction set for all code in
suspend-imx6.S.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Fixes: df595746 ("ARM: imx: add suspend in ocram support for i.mx6q")
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

RTC pcf2127 device driver has changed default behaviour of the watchdog
feature in v5.11-rc1. Now you need to explicitly enable it with a
device tree property, "reset-source", when used in the board design.

Fixes: 71ac1345 ("rtc: pcf2127: only use watchdog when explicitly available")
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: Bruno Thomsen <bth@kamstrup.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.

On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:

  mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
  mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
  hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
  mem=638M@385M

Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.

This was manifested in a bug that surfaced in response to
commit 7fef431b ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.

We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

With [1] integrated and all users of the config symbols removed, we
can safely remove the options from defconfig.

[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20201026170624.24241-1-nm@ti.com/Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210107132228.6577-1-nm@ti.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control is
transferred from the middle of the loop, as in the case of a return
or break or goto, there is no decrement thus ultimately resulting in
a memory leak.

Fix a potential memory leak in arm-integrator-lm.c by inserting
of_node_put() before a return statement.

Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200829174154.GA9319@Kaladin
Link: https://lore.kernel.org/r/20210112092549.251548-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.11:

- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
  #pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
  index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
  with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.

* tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
  ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
  ARM: imx: fix imx8m dependencies
  ARM: dts: tbs2910: rename MMC node aliases
  arm64: dts: ls1028a: fix the offset of the reset register
  arm64: dts: imx8mn: Fix duplicate node name
  ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight

Link: https://lore.kernel.org/r/20210112131224.GI28365@dragonSigned-off-by: Arnd Bergmann <arnd@arndb.de>

After converting am335x to probe devices with simple-pm-bus I noticed
that we are not passing auxdata for of_platform_populate() like we do
with simple-bus.

While device tree using SoCs should no longer need platform data, there
are still quite a few drivers that still need it as can be seen with
git grep OF_DEV_AUXDATA. We want to have simple-pm-bus be usable as a
replacement for simple-bus also for cases where OF_DEV_AUXDATA is still
needed.

Let's fix the issue by passing auxdata as platform data to simple-pm-bus.
That way the SoCs needing this can pass the auxdata with OF_DEV_AUXDATA.
And let's pass the auxdata for omaps to fix the issue for am335x.

As an alternative solution, adding simple-pm-bus handling directly to
drivers/of/platform.c was considered, but we would still need simple-pm-bus
device driver. So passing auxdata as platform data seems like the simplest
solution.

Fixes: 5a230524 ("ARM: dts: Use simple-pm-bus for genpd for am3 l4_wkup")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We now depend on SIMPLE_PM_BUS for probing devices. While we have it
selected in omap2plus_defconfig, custom configs can fail if it's missing.

As SIMPLE_PM_BUS depends on OF and PM, we must now select PM in Kconfig.
We have already OF selected by ARCH_MULTIPLATFORM.

Let's also drop the earlier PM dependency entries as suggested by
Geert Uytterhoeven <geert@linux-m68k.org>.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Fixes: 5a230524 ("ARM: dts: Use simple-pm-bus for genpd for am3 l4_wkup")
Signed-off-by: Tony Lindgren <tony@atomide.com>

We get suspcious RCU usage splats with cpuidle in several places in
omap_enter_idle_coupled() with the kernel debug options enabled:

RCU used illegally from extended quiescent state!
...
(_raw_spin_lock_irqsave)
(omap_enter_idle_coupled+0x17c/0x2d8)
(omap_enter_idle_coupled)
(cpuidle_enter_state)
(cpuidle_enter_state_coupled)
(cpuidle_enter)

Let's use RCU_NONIDLE to suppress these splats. Things got changed around
with commit 1098582a ("sched,idle,rcu: Push rcu_idle deeper into the
idle path") that started triggering these warnings.

For the tick_broadcast related calls, ideally we'd just switch over to
using CPUIDLE_FLAG_TIMER_STOP for omap_enter_idle_coupled() to have the
generic cpuidle code handle the tick_broadcast related calls for us and
then just drop the tick_broadcast calls here.

But we're currently missing the call in the common cpuidle code for
tick_broadcast_enable() that CPU1 hotplug needs as described in earlier
commit 50d6b3cf ("ARM: OMAP2+: fix lack of timer interrupts on CPU1
after hotplug").

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.

Fixes: fde180f0 ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.

Fixes: ac68793f ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:

arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'

Fixes: ac68793f ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.

Fixes: fde180f0 ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The uSD slot has no WP detection, disable it.

Fixes: 34e0c784 ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The DHCOM SoM uSD slot card detect signal is connected to GPIO PG1,
describe it in the DT.

Fixes: 34e0c784 ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The uSD card detect signal on the DH DRC02 is active-high, with
a default pull down resistor on the board. Invert the polarity.

Fixes: fde180f0 ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
Note that this could not be tested on prototype SoMs, now that it is
tested, this issue surfaced, so it needs to be fixed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.

This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).

Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

2 regulator descriptions carry identical naming.

This leads to following boot warning:
[    0.173138] debugfs: Directory 'vdd1p8' with parent 'regulator' already present!

Fix this by renaming the one used for audio.

Fixes: 5051bff3 ("ARM: dts: imx: ventana: add LTC3676 PMIC support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix typo so the gpio i2c busses are really disabled.

Fixes: 21252127 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Selecting ARM_GIC_V3 on non-CP15 processors leads to build failures
like

arch/arm/include/asm/arch_gicv3.h: In function 'write_ICC_AP1R3_EL1':
arch/arm/include/asm/arch_gicv3.h:36:40: error: 'c12' undeclared (first use in this function)
   36 | #define __ICC_AP1Rx(x)   __ACCESS_CP15(c12, 0, c9, x)
      |                                        ^~~

Add a dependency to only enable the gic driver when building for
at an ARMv7 target, which is the closes approximation to the ARMv8
processor that is actually in this chip.

Fixes: fc40200e ("soc: imx: increase build coverage for imx8m soc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

to be consistent with kernel versions up to v5.9 (mmc aliases not used here).
usdhc1 is not wired up on this board and therefore cannot be used.
Start mmc aliases with usdhc2.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org                # 5.10.x
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Merge tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Search for <ncurses.h> in the default header path of HOSTCC

 - Tweak the option order to be kind to old BSD awk

 - Remove 'kvmconfig' and 'xenconfig' shorthands

 - Fix documentation

* tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Documentation: kbuild: Fix section reference
  kconfig: remove 'kvmconfig' and 'xenconfig' shorthands
  lib/raid6: Let $(UNROLL) rules work with macOS userland
  kconfig: Support building mconf with vendor sysroot ncurses
  kconfig: config script: add a little user help
  MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal