Not all devices use proc_comm and determining if a clock is local
vs. remote is fragile when done by comparing clk_ops pointers.
Instead, implement an is_local() function for all clk_ops to
determine if the clock is local. Doing this allows us to remove
the last references to clk_ops_pcom from clock.c and compile it
for targets with CONFIG_MSM_PROC_COMM=n.

We don't need to set the clk_ops at runtime until 7x30 local
clock detection comes in. Right now it's just complicating things
so just set the ops pointer statically.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

WARNING: vmlinux.o(.cpuinit.text+0xc80): Section mismatch in
reference from the function boot_secondary() to the variable
.init.text:msm_secondary_startup
The function __cpuinit boot_secondary() references a variable
__init msm_secondary_startup.  If msm_secondary_startup is only
used by boot_secondary then annotate msm_secondary_startup with
a matching annotation.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Replace a BSD-style license in Code Aurora Forum authored files with
an explicit GPLv2.
Signed-off-by: David Brown <davidb@codeaurora.org>

* msm-core:
  msm: iommu: Enable IOMMU support for MSM8960
  msm: iommu: Generalize platform data for multiple targets
  msm: iommu: Create a Kconfig item for the IOMMU driver

Allow IOMMU to be selected for MSM8960 now that the
platform data has been generalized.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Make the IOMMU platform data target-independent in
preparation for adding MSM8960 IOMMU support. The IOMMU
configuration on MSM8x60 and MSM8960 is identical and the
same platform data can be used for both.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Break the IOMMU driver out as a Kconfig item. Initially it
was decided to always build this in for 8x60, but this
driver is not strictly necessary and should be optionally
selectable.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

* msm-core:
  msm: serial: Add MSM8960 serial support

Add the device definitions and platform data to support
the console serial port on MSM8960 Simulator and RUMI3
targets.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

* msm-core:
  msm: Clean up useless ifdefs
  msm: clock: Add support for more proc_comm clocks
  msm: clock: Invert debugfs directory layout
  msm: clock: Move debugfs code from clock.c to clock-debug.c
  msm: clock: Remove 7x30 and pcom includes from clock.h
  msm: clock: Remove unused code and definitions
  msm: Warning fix in trout gpio board file
  msm: Remove broken register definition from trout

Remove ifdefs that do nothing, either from having the code
between them previously removed, or from having been
accidentally added to the wrong file.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Add support for the ce, codec_ssbi, uart clocks, and i2c clocks.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

There are currently 3 separate directories for clock debugging in
debugfs: clk_enable, clk_rate, and clk_local. Each of these
directories contains a list of clocks. This is rather annoying
when you are focusing on one clock and want to enable/disable it
and then check its rate. You either have to cd to the other
directory or cat ../clk_rate/<clk>.

Invert the layout so that there is one clock directory containing
a directory for each clock. Inside each respective clock
directory place an enable, rate, and is_local file relating to
the clk_enable, clk_disable, and clk_local directories that exist
today.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

The clock debugfs code is large enough, and easy enough to separate,
that it deserves its own file which is compiled only when
CONFIG_DEBUG_FS is enabled.

Also, cleanup header file #includes that are no longer required.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Matt Wagantall <mattw@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

clock.h includes clock-pcom.h and clock-7x30.h when it really
doesn't need to. Remove the includes and fixup breakages.
Reviewed-By: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

This code is dead or otherwise useless so just remove it.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

arch/arm/mach-msm/board-trout-gpio.c: In function 'trout_gpio_to_irq':
arch/arm/mach-msm/board-trout-gpio.c:77: error: unused variable 'msm_gpio'
Signed-off-by: David Brown <davidb@codeaurora.org>

Missed a register change with the clock cleanup on the MSM7x01 targets.
Signed-off-by: David Brown <davidb@codeaurora.org>

* msm-8960:
  msm: Support for the MSM8960 RUMI3 target
  msm: Support for the MSM8960 Simulator target
  msm: Makefile cleanup
  msm: timer: Timer support for MSM8960
  msm: Add MSM 8960 cpu_is check
  msm: irqs-8960: Interrupt map for MSM8960
  msm: Physical offset for MSM8960
  msm: io: I/O register definitions for MSM8960
  msm: Generalize QGIC registers
  msm: Generalize timer register mappings
  msm: Add CPU queries

* msm-fb:
  video/msm_fb: use system_wq instead of dedicated workqueues

With cmwq, there's no reason to use separate workqueues.  Drop
msmfb_info->resume_workqueue and use system_wq instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: linux-usb@vger.kernel.org
Signed-off-by: David Brown <davidb@codeaurora.org>

* msm-sdcc:
  msm: 8x50: Add initial support for SDCC
  mmc: msm_sdcc: Add gpio handling function to driver
  drivers: mmc: msm: remove clock disable in probe
  mmc: msm: fix dma usage not to use internal APIs

* msm-8960:
  msm: Support for the MSM8960 RUMI3 target
  msm: Support for the MSM8960 Simulator target
  msm: Makefile cleanup
  msm: timer: Timer support for MSM8960
  msm: Add MSM 8960 cpu_is check
  msm: irqs-8960: Interrupt map for MSM8960
  msm: Physical offset for MSM8960
  msm: io: I/O register definitions for MSM8960
  msm: Generalize QGIC registers
  msm: Generalize timer register mappings
  msm: Add CPU queries

* msm-uart:
  serial: msm: Add support for UARTDM cores
  msm: Add name field to UART resources

This is completely board specific and therefore must be provided
on a per-board basis.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: David Brown <davidb@codeaurora.org>

Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>

Configure SDCC GPIOs when the host is powered up or powered off.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>

The probe function adds the MMC host which can start accepting request
immediately. There is an assumption here that no requests happen
immediatly, but it's not always the case. This assumption can causes
a BUG() when the clocks are disabled. The fix is to just remove the
clock disable in the probe function.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>

Remove parts of this driver which use internal API calls. This
replaces the calls as suggested by Russell King.

Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>

* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (101 commits)
  [media] staging/lirc: fix mem leaks and ptr err usage
  [media] hdpvr: reduce latency of i2c read/write w/recycled buffer
  [media] hdpvr: enable IR part
  [media] rc/mceusb: timeout should be in ns, not us
  [media] v4l2-device: fix 'use-after-freed' oops
  [media] v4l2-dev: don't memset video_device.dev
  [media] zoran: use video_device_alloc instead of kmalloc
  [media] w9966: zero device state after a detach
  [media] v4l: Fix a use-before-set in the control framework
  [media] v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
  [media] DocBook/v4l: update V4L2 revision and update copyright years
  [media] DocBook/v4l: fix validation error in dev-rds.xml
  [media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
  [media] v4l2-ctrls: fix missing 'read-only' check
  [media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
  [media] ir-kbd-i2c: Add back defaults setting for Zilog Z8's at addr 0x71
  [media] lirc_zilog: Update TODO.lirc_zilog
  [media] lirc_zilog: Add Andy Walls to copyright notice and authors list
  [media] lirc_zilog: Remove useless struct i2c_driver.command function
  [media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
  ...

Add support for the next-generation version of the MSM UART
to the msm_serial driver. This version of the hardware is
similar to the original version, but has some DMA
capabilities that are used in PIO mode in this driver.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Add a name field to the I/O resources for the UARTs on MSM
targets in preparation for updates to the msm_serial
driver. The driver assumed there is one I/O resource per
UART, which is not the case on all targets.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Add the machine record, init code, and build support for
the MSM8960 RUMI3.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Add the board file, Kconfig options, and Makefile options
needed to build for the MSM8960 Simulator target.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Clean up some of the conditionals in the Makefile in
preparation for adding build support for MSM8960.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Modify the macros in the MSM timer driver to support the
MSM8960 chip.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Signed-off-by: David Brown <davidb@codeaurora.org>

Add the interrupt map for the Qualcomm MSM8960 chip. This
chip has an interrupt map that is different from previous
targets.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Add the physical memory offset value for the Qualcomm
MSM8960 chip.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>