module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since we always need to have set and get callbacks for McBSP sidetone it
makes sense to combine the two macro to create the two callbacks.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To remove duplicated code from the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

When asked to add the ST controls warn only if the st_data is missing.
In this way we do not block the otherwise functional card to probe.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In ddevice tree booted kernel all device have unique name and their device
id is set to 0.
Use the mcbsp->id for checking to decide which control set we should add
for McBSP sidetone handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is more idimatic for modern drivers. Also fix a couple of return
codes while we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make it scan better by writing ROM with capitals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We are using devm_ to allocate the GPIO so it will be freed automatically.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Doesn't make any practical difference given that _SUSPEND and _OFF are
equivalent for the driver but it's what we're really doing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make it easier to integrate the management of the clock supplying the
WM0010 with DAPM by providing a dummy supply widget which supplies the
interface widgets, this can be connected to clock outputs by the machines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

With appropriate clocking configuration the WM0010 driver supports 44.1kHz
audio; enable that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The Speyside platform by default has a WM0010 fitted.  Now that we have
a public driver hook it up in the machine integration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications.  Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There are some new WM1811 variants distinguished by both revision and
cust_id which need slightly different handling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fixes:
CC      arch/arm/mach-omap2/twl-common.o arch/arm/mach-omap2/twl-common.c:562: error: conflicting types for ‘omap_twl4030_audio_init’
arch/arm/mach-omap2/twl-common.h:62: error: previous declaration of ‘omap_twl4030_audio_init’ was here
make[1]: *** [arch/arm/mach-omap2/twl-common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2

When building the kernel with !SND_OMAP_SOC_OMAP_TWL4030
Reported-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To reflect the final devicetree node structure of McBSPs.

The initial OMAP McBSP DT structure was not able to describe the IP (and
it's versions) correctly.  The main issue was the sidetone block of
McBSP2/3 on OMAP3.  With this change in the DT description the OS can
get the needed information about the IP.

The sidetone is still not supported when the Linux kernel is booted with DT
since we still depend on hwmod to fill the resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Device tree support for McBSP modules on OMAP2+ SoC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Only create the devices in a legacy way if we do not have the DT data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We can use the has_ccr flag to replace the cpu_is_omap* checks.
This provides future proof implementation and we do not need to update the
code if new OMAP revision starts to use the McBSP driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

NUM_LINKS is no longer in use by the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remove the feature to configure the CLKR/FSR mux on McBSP port with 6pin
configuration.
When moving to devicetree these callback can no longer be used in a clean
way anymore.
If a board require to change the 6pin port to work in 4pin setup it needs
to set up the mux in the board file.
For OMAP2/3:
u32 devconf0;

/* McBSP1 CLKR/FSR signal to be connected to CLKX/FSX pin */
devconf0 = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
devconf0 |=  OMAP2_MCBSP1_CLKR_MASK | OMAP2_MCBSP1_FSR_MASK;
omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0);

For OMAP4:
u32 mcbsp_pad;

/* McBSP4 CLKR/FSR signal to be connected to CLKX/FSX pin */
mcbsp_pad = omap4_ctrl_pad_readl(OMAP2_CONTROL_DEVCONF0);
mcbsp_pad |=  ((1 << 31) | (1 << 30));
omap4_ctrl_pad_writel(mcbsp_pad, OMAP2_CONTROL_DEVCONF0);

In case when the kernel is booted with DT blob the pinctrl-single will be
provided as soon as it is enabled on the platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The muxing is done at board level, no need to do it in the ASoC machine
driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

am3517evm board uses McBSP1 for audio with 4pin configuration.
The CLKR/FSR signals need to be connected to CLKX/FSX pin of the SoC in
this case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

On OMAP2430 all McBSP ports have 128 word long buffer, enable the use of
the FIFO for the audio stack.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Move the McBSP CLKS re-parenting code to ASoC driver from
arch/arm/mach-omap2.
The call fort the re-parenting has been already limited to OMAP2+ SoC in
the ASoC driver. There is no longer need to have callback function for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Aids diagnostics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Should be no behaviour change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

codec_dai is not used in the function.

sound/soc/soc-compress.c: In function ‘soc_compr_set_params’:
sound/soc/soc-compress.c:156:22: warning:
unused variable ‘codec_dai’ [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Ramesh Babu K V <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds the support to parse the compress dai's and then also adds the
soc-compress.c file while handles the compress stream operations, mostly analogus
to what is done in the soc-pcm.c and aditional handling of the compress
opertaions
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Ramesh Babu K V <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Here we update the asoc structures to add compress stream definations
First the struct snd_soc_dai_driver adds a new member to indicate if the dai is
compressed or pcm. Next we add a new structre the struct snd_soc_compr_ops in
the struct snd_soc_dai_link. This is to be used for machine driver to perform
any opertaions required for setting up compressed audio streams

next is the compressed data operations, they are added using struct
snd_compr_ops in the struct snd_soc_platform_driver.
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Ramesh Babu K V <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>