This will allow to have static Device mapping and DT probe mapping for the
System Controller.

Temporary keep the call to ioremap_registers() until we have the binding
for the SDRAM/DDR Controller.

Temporary keep the main clock hardcoded to 12MHz until we have the binding
for the PMC.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

http://www.calao-systems.com/articles.php?lng=en&pg=6099

this daughter board add the following device:
 - Micro-SD socket
 - TTL 3V3 - (Tx/Rx/RTS/CTS)
 - I2C port
 - 0.96" Serial OLED Display Module (over UART)
 - MP3 decoder with Micro & Speakers
 - 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red)

for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT

used_led1 will not be re-add via DT as it's used by the motherboard too
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Use i2c-gpio and enable rv3029 RTC.

Enable the rtc in the sam9g20 defconfig.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

To achieve DT support, we need to populate a custom platform_data in a
private struct from DT information. To simplify code, the adapter and
algorithm are also put into the private struct.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable the nand in the cpu module with the partition.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

- nand-ecc-mode : String, operation mode of the NAND ecc mode.
  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
  "soft_bch".
- nand-bus-width : 8 or 16 bus width if not present 8
- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stefan Roese <sr@denx.de>

of_property_read_bool

Search for a property in a device node.
Returns true if the property exist false otherwise.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

Enable it on Calao board too as they are in DT too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This will allow to enable it from the board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>

So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).

Set ecc mode in the boards to soft as currently in the driver.

Move platform data to a common header
include/linux/platform_data/atmel_nand.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use the gpio for d7 as we do not support yet the pwm led via dt.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)

Support for those new features are retrieved from the device tree
compatibility string.

Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add these SMC accessors to the at91sam9x5 as we will need them for
NAND flash (for instance).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Some SoC have a 32 bit variant of Timer Counter Blocks. We do not
need the chaining of two 16 bit counters anymore for them.

The SoC nature is deduced from the device tree "compatible" string.
For non-device-tree configurations, backward compatibility is maintained
by using the default 16 bit counter configuration.

This patch addresses both the atmel_tclib and its user: tcb_clksrc
clocksource.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.

The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

Requesting iomem region and ioremaping is now done using
the resource size specified instead of a constant value.

Each <SoC>_device.c file is modified accordingly to reflect
actual user interface size.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Traces related to IRQ management are useful for timers in case of
non-working IRQ subsystem (switch to irq_domain for instance).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Retreive registers address and IRQ from device tree entry.
Called from at91_dt_init_irq() so that timers are up-n-running
when timers initialization will occur.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change error path and interrupts property handling]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Both AIC and GPIO controllers are now using the standard of_irq_init()
function to initialize IRQs in case of DT use.
The DT specific initialization functions are now separated from the
non-DT case and are now using "linear" irq domains.
The .map() irqdomain operation is responsible for positioning the IRQ
handlers. In AIC case, the Linux IRQ number is directly programmed in
the hardware to avoid an additional reverse mapping operation.
The AIC position its irq domain as the "default" irq domain.

For DT case, the priority is not yet filled in the SMR. It will be the
subject of another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Adding of irqdomain in AIC code make the specification
of the irq domain in board file useless.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This value is determined at runtime using device tree or platform data
information.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Replace the gpio_to_irq() macro by a plain gpiolib .to_irq() handler.
This call is using the irqdomain to translate hardware to Linux
IRQ numbers.
The irq_to_gpio() macro is completely removed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Protect build failure in case of non-DT configuration: the
gpio_chip structure does not have a of_node field in case of
!CONFIG_OF_GPIO.

Keep this in a separate patch as it can be reverted if the
field is added for both DT/non-DT cases.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.

Original idea and code by Jean-Christophe Plagniol-Villard.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

What was true only on at91sam9263 about the sharing of a single AIC
IRQ line for several GPIO banks is now used by several Atmel SoCs.

Change a variable name to allow better understanding while
introducing IRQ domains in following patches.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

irq_to_gpio() macro will be removed from AT91 GPIO interrupt
controller. So we replace it with the use of gpio_to_irq()
and a reworked test.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-usb@vger.kernel.org

gpio_to_irq() implementation will be moved from a macro to a
plain function: we cannot use it in a structure initialization
anymore.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>

Add an irqdomain for the AIC interrupt controller.
The device tree support is mapping the registers and
is using the irq_domain_add_legacy() to manage hwirq
translation.
The documentation is describing the meaning of the
two cells required for using this "interrupt-controller"
in a device tree node.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Merge branch 'at91-3.4-base2+cleanup' of git://github.com/at91linux/linux-at91 into at91/staging/base2+cleanup

* 'at91-3.4-base2+cleanup' of git://github.com/at91linux/linux-at91: (20 commits)
  ARM: at91: properly sort dtb files in Makefile.boot
  ARM: at91: add at91sam9g25ek.dts in Makefile.boot
  ARM: at91/board-dt: drop default console
  Atmel: move console default platform_device to serial driver
  ARM: at91: merge SRAM Memory banks thanks to mirroring
  ARM: at91: finally drop at91_sys_read/write
  ARM: at91/rtc-at91sam9: pass the GPBR to use via resources
  ARM: at91:rtc/rtc-at91sam9: ioremap register bank
  ARM: at91/rtc-at91sam9: each SoC can select the RTT device to use
  ARM: at91/PMC: make register base soc independent
  ARM: at91/PMC: move assignment out of printf
  ARM: at91/pm_slowclock: add runtime detection of memory contoller
  ARM: at91: make sdram/ddr register base soc independent
  ARM: at91: move at91rm9200 sdramc defines to at91rm9200_sdramc.h
  ARM: at91/pm_slowclock: function slow_clock() accepts parameters
  ARM: at91/pm_slowclock: rename register to named define
  ARM: at91/ST: remove not needed casts
  ARM: at91: make ST (System Timer) soc independent
  ARM: at91: make matrix register base soc independent
  ARM: at91/at91x40: remove use of at91_sys_read/write

Based on top of the at91/9x5, rmk/for-armsoc, at91/device-board,
at91/pm_cleanup and at91/base.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

TWL4030 depends on IRQ_DOMAIN support, so this patch selects it in Kconfig.
It used to be that CONFIG_IRQ_DOMAIN must only be selected by the architecture,
but recent cleanups have fixed it so that it is safe to select from anywhere.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[grant.likely: Changed from a depends to a select]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>

Sparc has its own helpers for translating address ranges when the device
tree is parsed at boot time, and it isn't able to use of_platform_populate().
However, there are some device drivers that want to use that function on
other DT enabled platforms (ie. TWL4030).  This patch adds an empty
of_platform_populate() implementation that returns an error when
CONFIG_OF_ADDRESS is not selected.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>