The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethernet PHYs can maintain statistics, for example errors while idle
and receive errors. Add an ethtool mechanism to retrieve these
statistics, using the same model as MAC statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2015-12-29

This series contains updates to ixgbe and ixgbevf.

William Dauchy provides a fix for ixgbevf that was implemented for ixgbe,
commit 5d6002b7 ("ixgbe: Fix handling of NAPI budget when multiple
queues are enabled per vector"). The issue was that the polling routine
would increase the budget for receive to at least 1 per queue if multiple
queues were present, which resulted in receive packets being processed
when the budget was 0.

Emil provides minor cleanups for ixgbevf, one being that we need to
check rx_itr_setting with == and not &, since it is not a mask.  Added
QSFP PHY support in ixgbe to allow for more accurate reporting of port
settings.  Fixed the max RSS limit for X550 which is 63, not 64.

Veola fixes ixgbe ethtool reporting of backplane type interfaces as
1000/10000baseT link modes, instead, report the media as KR, KX or KX4
based on the backplane interface present.

Mark cleans up redundancy in the setting of hw_enc_features that makes
it appear that X550 has more encapsulation features than other devices.
Also do not set NETIF_F_SG any longer since that is set by the
register_netdev() call.  Also fixed the X550EM_x revision check, which
needs to check a value, not just a bit.

Alex Duyck fixes additional bugs in ixgbe_clear_vf_vlans(), one being
that the mask was using a divide instead of a modulus, which resulted
in the mask bit being incorrectly set to 0 or 1 based on the value of
the VF being tested.  Alex also found that he was not consistent in
using the "word" argument as an offset or as a register offset, so
made the code consistently use word as the offset in the array.

v2: dropped patch 8 of the original series, as it was undoing a part of
    the fix Alex Duyck was doing in patch 9 of the original series.
    Dropped based on feedback from Emil (the author).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

The following patch set contains some feature additions, code re-organization
and cleanup and a few non-critical fixes. Pls consider applying this to
the net-next tree. Thanks.

v3 changes: add a default case to the switch statement in patch 5 to
satisfy the compiler (-Wswitch).
v2 changes: replaced an if/else block that checks for error values with a
switch/case statement in patch 5.

Patch 1 fixes VF link state transition from disabled to auto that did
not work due to an issue in the FW. This issue could not be fixed in FW due
to some backward compatibility issues it causes with released drivers.
The issue has been fixed by introducing a new version (v2) of the cmd
from 10.6 FW onwards. This patch adds support for v2 version of this cmd.

Patch 2 reports a EOPNOTSUPP status to ethtool when the user tries to
configure BE3/SRIOV in VEPA mode as it is not supported by the chip.

Patch 3 cleansup FW flash image related constant definitions. Many of these
definitions (such as section offset values) were defined in decimal format
rather than hexa-decimal. This makes this part of the code un-readable.
Also some defines related to BE2 are labeld "g2" and defines related to BE3
are labeled "g3".  This patch cleans up all of this to make this code more
readable.

Patch 4 moves the FW cmd code to be_cmds.c. All code relating to FW cmds
has been in be_cmds.[ch], excepting FW flash cmd related code.
This patch moves these routines from be_main.c to be_cmds.c.

Patch 5 adds a log message to report digital signature errors while
flashing a FW image. From FW version 11.0 onwards, the FW supports a new
"secure mode" feature (based on a jumper setting on the adapter.) In this
mode, the FW image when flashed is authenticated with a digital signature.

Patch 6 removes a line of code that has no effect.

Patch 7 removes some unused variables.

Patch 8 fixes port resource descriptor query via the GET_PROFILE FW cmd.
An earlier commit passed a specific pf_num while issuing this cmd as FW
returns descriptors for all functions when pf_num is zero. But, when pf_num
is set to a non-zero value, FW does not return the port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.

Patch 9 adds support for ethtool get-dump feature. In the past when this
option was not yet available, this feature was supported via the
--register-dump option as a workaround.  This patch removes support for
FW-dump via --register-dump option as it is now available via --get-dump
option. Even though the "ethtool --register-dump" cmd which used to work
earlier, will now fail with ENOTSUPP error, we feel it is not an issue as
this is used only for diagnostics purpose.

Patch 10 bumps up the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for ethtool's --get-dump option in be2net,
to retrieve FW dump. In the past when this option was not yet available,
this feature was supported via the --register-dump option as a workaround.
This patch removes support for FW-dump via --register-dump option as it is
now available via --get-dump option. Even though the
"ethtool --register-dump" cmd which used to work earlier, will now fail
with ENOTSUPP error, we feel it is not an issue as this is used only
for diagnostics purpose.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 72ef3a88 ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd") passed a specific pf_num while issuing a
GET_PROFILE_CONFIG cmd as FW returns descriptors for all functions when
pf_num is zero. But, when pf_num is set to a non-zero value, FW does not
return the Port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.

Fixes: 72ef3a88 ("be2net: set pci_func_num while issuing
		     GET_PROFILE_CONFIG cmd")
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eeh_error, fw_timeout, hw_error variables in the be_adapter structure are
not used anymore. An earlier patch that introduced adapter->err_flags to
store this information missed removing these variables.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes a line of code that changes adapter->recommended_prio
value followed by yet another assignment.
Also, the variable is used to store the vlan priority value that is already
shifted to the PCP bits position in the vlan tag format. Hence, the name of
this variable is changed to recommended_prio_bits.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

(based on a jumper setting on the adapter.) In this mode, the FW image when
flashed is authenticated with a digital signature. This patch logs
appropriate error messages and return a status to ethtool when errors
relating to FW image authentication occur.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All code relating to FW cmds is in be_cmds.[ch] excepting FW flash cmd
related code. This patch moves these routines from be_main.c to be_cmds.c
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many constant definitions relating to the FW-image layout
(such as section offset values) were defined in decimal format rather than
hexa-decimal. This makes this part of the code un-readable. Also some
defines related to BE2 are labeld "g2" and defines related to BE3 are
labeled "g3".  This patch cleans up all of this to make this code more
readable.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 chip doesn't support VEPA mode.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VF link state setting transition from "disable" to "auto" does not work
due to a bug in SET_LOGICAL_LINK_CONFIG_V1 cmd in FW. This issue could not
be fixed in FW due to some backward compatibility issues it causes with
some released drivers. The issue has been fixed by introducing a new
version (v2) of the cmd from 10.6 FW onwards. In v2, to set the VF link
state to auto, both PLINK_ENABLE and PLINK_TRACK bits have to be set to 1.

The VF link state setting feature now works on Lancer chips too from
FW ver 10.6.315.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset.  As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.

Another issue found is that the mask was using a divide instead of a
modulus.  As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested.  As a result the wrong
VFs were having their VLANs cleared if they were enabled.

I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.

I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted.  The two should be equivalent so the change should be safe.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

X550 allows for up to 64 RSS queues, but the driver can have max
of 63 (-1 MSIX vector for link).

On systems with >= 64 CPUs the driver will set the redirection table
for all 64 queues which will result in packets being dropped.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the
backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add missing QSFP PHY types to allow for more accurate reporting of
port settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

adapter->rx_itr_setting is not a mask so check it with == instead of &
do not default to 12K interrupts in ixgbevf_set_itr()

There should be no functional effect from these changes.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is the same patch as for ixgbe but applied differently according to
busy polling.  See commit 5d6002b7 ("ixgbe: Fix handling of NAPI
budget when multiple queues are enabled per vector")
Signed-off-by: William Dauchy <william@gandi.net>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ming Lei says:

====================
bpf: hash: use per-bucket spinlock

This patchset tries to optimize ebpf hash map, and follows
the idea:

        Both htab_map_update_elem() and htab_map_delete_elem()
        can be called from eBPF program, and they may be in kernel
        hot path, it isn't efficient to use a per-hashtable lock
        in this two helpers, so this patch converts the lock into
        per-bucket spinlock.

With this patchset, looks the performance penalty from eBPF
decreased a lot, see the following test:

        1) run 'tools/biolatency' of bcc before running block test;

        2) run fio to test block throught over /dev/nullb0,
        (randread, 16jobs, libaio, 4k bs) and the test box
        is one 24cores(dual sockets) VM server:
        - without patchset:  607K IOPS
        - with this patchset: 1184K IOPS
        - without running eBPF prog: 1492K IOPS

TODO:
        - remove the per-hashtable atomic counter

V2:
        - fix checking on buckets size
V1:
        - fix the wrong 3/3 patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Both htab_map_update_elem() and htab_map_delete_elem() can be
called from eBPF program, and they may be in kernel hot path,
so it isn't efficient to use a per-hashtable lock in this two
helpers.

The per-hashtable spinlock is used for protecting bucket's
hlist, and per-bucket lock is just enough. This patch converts
the per-hashtable lock into per-bucket spinlock, so that
contention can be decreased a lot.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The spinlock is just used for protecting the per-bucket
hlist, so it isn't needed for selecting bucket.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preparing for removing global per-hashtable lock, so
the counter need to be defined as aotmic_t first.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Patches for net-next.

Mainly clean-ups, optimizations, and updating to the latest firmware
interface spec.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added the PCI IDs for the BCM57301 and BCM57402 controllers.
Signed-off-by: David Christensen <davidch@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This interface will be forward compatible with future changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer firmware will return the ring group resource when we call
hwrm_func_qcaps().  To be compatible with older firmware, use the
number of tx rings as the number of ring groups if the older firmware
returns 0.  When determining how many rx rings we can support, take
the ring group resource in account as well in _bnxt_get_max_rings().
Divide and assign the ring groups to VFs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to keep track of all resources, such as rx rings, tx rings,
cmpl rings, rss contexts, stats contexts, vnics, after we have
divided them for the VFs.  Otherwise, subsequent ring changes on
the PF may not work correctly.

We adjust all max resources in struct bnxt_pf_info after they have been
assigned to the VFs.  There is no need to keep the separate
max_pf_tx_rings and max_pf_rx_rings.

When SR-IOV is disabled, we call bnxt_hwrm_func_qcaps() to restore the
max resources for the PF.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Use local variable pf for repeated access to this pointer.

2.  The 2nd argument num_vfs was unnecessarily declared as pointer to int.
This function doesn't change num_vfs so change the argument to int.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware resources required to enable NTUPLE varies depending on
how many rx channels are configured.  We need to make sure we have the
resources before we enable NTUPLE.  Add bnxt_rfs_capable() to do the
checking.

In addition, we need to do the same checking in ndo_fix_features().  As
the rx channels are changed using ethtool -L, we call
netdev_update_features() to make the necessary adjustment for NTUPLE.

Calling netdev_update_features() in netif_running() state but before
calling bnxt_open_nic() would be a problem.  To make this work,
bnxt_set_features() has to be modified to test for BNXT_STATE_OPEN for
the true hardware state instead of checking netif_running().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If hardware completes single segment rx frames, don't bother setting
up all the GRO related fields.  Pass the SKB up as a normal frame.
Reviewed-by: vasundhara volam <vvolam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also, no need to check for bp->rx_nr_rings as it is always >= 1.  If the
allocation fails, it is not a fatal error and we can still proceed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rx_l4_csum_error is now incremented only when offload is enabled
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NC-SI firmware of type apeFW (10) is now supported.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>