- 14 Aug, 2018 40 commits
-
-
NeilBrown authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 011abdc9 upstream. If "re-add" is written to the "state" file for a device which is faulty, this has an effect similar to removing and re-adding the device. It should take up the same slot in the array that it previously had, and an accelerated (e.g. bitmap-based) rebuild should happen. The slot that "it previously had" is determined by rdev->saved_raid_disk. However this is not set when a device fails (only when a device is added), and it is cleared when resync completes. This means that "re-add" will normally work once, but may not work a second time. This patch includes two fixes. 1/ when a device fails, record the ->raid_disk value in ->saved_raid_disk before clearing ->raid_disk 2/ when "re-add" is written to a device for which ->saved_raid_disk is not set, fail. I think this is suitable for stable as it can cause re-adding a device to be forced to do a full resync which takes a lot longer and so puts data at more risk. Cc: <stable@vger.kernel.org> (v4.1) Fixes: 97f6cd39 ("md-cluster: re-add capabilities") Signed-off-by:
NeilBrown <neilb@suse.com> Reviewed-by:
Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by:
Khalid Elmously <khalid.elmously@canonical.com>
-
Robert Elliott authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 254a4cd5 upstream. The pmem driver does not honor a forced read-only setting for very long: $ blockdev --setro /dev/pmem0 $ blockdev --getro /dev/pmem0 1 followed by various commands like these: $ blockdev --rereadpt /dev/pmem0 or $ mkfs.ext4 /dev/pmem0 results in this in the kernel serial log: nd_pmem namespace0.0: region0 read-write, marking pmem0 read-write with the read-only setting lost: $ blockdev --getro /dev/pmem0 0 That's from bus.c nvdimm_revalidate_disk(), which always applies the setting from nd_region (which is initially based on the ACPI NFIT NVDIMM state flags not_armed bit). In contrast, commit 20bd1d02 ("scsi: sd: Keep disk read-only when re-reading partition") fixed this issue for SCSI devices to preserve the previous setting if it was set to read-only. This patch modifies bus.c to preserve any previous read-only setting. It also eliminates the kernel serial log print except for cases where read-write is changed to read-only, so it doesn't print read-only to read-only non-changes. Cc: <stable@vger.kernel.org> Fixes: 58138820 ("libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only") Signed-off-by:
Robert Elliott <elliott@hpe.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 6a765508 upstream. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 ZFCP_DBF_REC_TRIG Tag : ....... LUN : 0x... WWPN : 0x... D_ID : 0x... Adapter status : 0x... Port status : 0x... LUN status : 0x... Ready count : 0x... Running count : 0x... ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_... ERP need : 0xc0 ZFCP_ERP_ACTION_NONE Signed-off-by:
Steffen Maier <maier@linux.ibm.com> Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by:
Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 8c3d20aa upstream. That other commit introduced an inconsistency because it would trace on ERP_FAILED for all callers of port forced reopen triggers (not just terminate_rport_io), but it would not trace on ERP_FAILED for all callers of other ERP triggers such as adapter, port regular, LUN. Therefore, generalize that other commit. zfcp_erp_action_enqueue() already had two early outs which re-used the one zfcp_dbf_rec_trig() call. All ERP trigger functions finally run through zfcp_erp_action_enqueue(). So move the special handling for ZFCP_STATUS_COMMON_ERP_FAILED into zfcp_erp_action_enqueue() and add another early out with new trace marker for pseudo ERP need in this case. This removes all early returns from all ERP trigger functions so we always end up at zfcp_dbf_rec_trig(). Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 ZFCP_DBF_REC_TRIG Tag : ....... LUN : 0x... WWPN : 0x... D_ID : 0x... Adapter status : 0x... Port status : 0x... LUN status : 0x... Ready count : 0x... Running count : 0x... ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_... ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit d70aab55 upstream. For problem determination we always want to see when we were invoked on the terminate_rport_io callback whether we perform something or not. Temporal event sequence of interest with a long fast_io_fail_tmo of 27 sec: loose remote port t workqueue [s] zfcp_q_<dev> IRQ zfcperp<dev> === ================== =================== ============================ 0 recv RSCN q p.test_link_work block rport start fast_io_fail_tmo send ADISC ELS 4 recv ADISC fail block zfcp_port port forced reopen send open port 12 recv open port fail q p.gid_pn_work zfcp_erp_wakeup (zfcp_erp_wait would return) GID_PN fail Before this point, we got a SCSI trace with tag "sctrpi1" on fast_io_fail, e.g. with the typical 5 sec setting. port.status |= ERP_FAILED If fast_io_fail_tmo triggers after this point, we missed a SCSI trace. workqueue fc_dl_<host> ================== 27 fc_timeout_fail_rport_io fc_terminate_rport_io zfcp_scsi_terminate_rport_io zfcp_erp_port_forced_reopen _zfcp_erp_port_forced_reopen if (port.status & ERP_FAILED) return; Therefore, write a trace before above early return. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 ZFCP_DBF_REC_TRIG Tag : sctrpi1 SCSI terminate rport I/O LUN : 0xffffffffffffffff none (invalid) WWPN : 0x<wwpn> D_ID : 0x<n_port_id> Adapter status : 0x... Port status : 0x... LUN status : 0x00000000 none (invalid) Ready count : 0x... Running count : 0x... ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 96d92704 upstream. get_device() and its internally used kobject_get() only return NULL if they get passed NULL as argument. zfcp_get_port_by_wwpn() loops over adapter->port_list so the iteration variable port is always non-NULL. Struct device is embedded in struct zfcp_port so &port->dev is always non-NULL. This is the argument to get_device(). However, if we get an fc_rport in terminate_rport_io() for which we cannot find a match within zfcp_get_port_by_wwpn(), the latter can return NULL. v2.6.30 commit 70932935 ("[SCSI] zfcp: Fix oops when port disappears") introduced an early return without adding a trace record for this case. Even if we don't need recovery in this case, for debugging we should still see that our callback was invoked originally by scsi_transport_fc. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : sctrpin SCSI terminate rport I/O, no zfcp port LUN : 0xffffffffffffffff none (invalid) WWPN : 0x<wwpn> WWPN D_ID : 0x<n_port_id> N_Port-ID Adapter status : 0x... Port status : 0xffffffff unknown (-1) LUN status : 0x00000000 none (invalid) Ready count : 0x... Running count : 0x... ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED ERP need : 0xc0 ZFCP_ERP_ACTION_NONE Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 512857a7 upstream. If a SCSI device is deleted during scsi_eh host reset, we cannot get a reference to the SCSI device anymore since scsi_device_get returns !=0 by design. Assuming the recovery of adapter and port(s) was successful, zfcp_erp_strategy_followup_success() attempts to trigger a LUN reset for the half-gone SCSI device. Unfortunately, it causes the following confusing trace record which states that zfcp will do a LUN recovery as "ERP need" is ZFCP_ERP_ACTION_REOPEN_LUN == 1 and equals "ERP want". Old example trace record formatted with zfcpdbf from s390-tools: Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded LUN : 0x<FCP_LUN> WWPN : 0x<WWPN> D_ID : 0x<N_Port-ID> Adapter status : 0x5400050b Port status : 0x54000001 LUN status : 0x40000000 ZFCP_STATUS_COMMON_RUNNING but not ZFCP_STATUS_COMMON_UNBLOCKED as it was closed on close part of adapter reopen ERP want : 0x01 ERP need : 0x01 misleading However, zfcp_erp_setup_act() returns NULL as it cannot get the reference. Hence, zfcp_erp_action_enqueue() takes an early goto out and _NO_ recovery actually happens. We always do want the recovery trigger trace record even if no erp_action could be enqueued as in this case. For other cases where we did not enqueue an erp_action, 'need' has always been zero to indicate this. In order to indicate above goto out, introduce an eyecatcher "flag" to mark the "ERP need" as 'not needed' but still keep the information which erp_action type, that zfcp_erp_required_act() had decided upon, is needed. 0xc_ is chosen to be visibly different from 0x0_ in "ERP want". New example trace record formatted with zfcpdbf from s390-tools: Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded LUN : 0x<FCP_LUN> WWPN : 0x<WWPN> D_ID : 0x<N_Port-ID> Adapter status : 0x5400050b Port status : 0x54000001 LUN status : 0x40000000 ERP want : 0x01 ERP need : 0xc1 would need LUN ERP, but no action set up ^ Before v2.6.38 commit ae0904f6 ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.") we could detect this case because the "erp_action" field in the trace was NULL. The rework removed erp_action as argument and field from the trace. This patch here is for tracing. A fix to allow LUN recovery in the case at hand is a topic for a separate patch. See also commit fdbd1c5e ("[SCSI] zfcp: Allow running unit/LUN shutdown without acquiring reference") for a similar case and background info. Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 81979ae6 upstream. We already have a SCSI trace for the end of abort and scsi_eh TMF. Due to zfcp_erp_wait() and fc_block_scsi_eh() time can pass between the start of our eh callback and an actual send/recv of an abort / TMF request. In order to see the temporal sequence including any abort / TMF send retries, add a trace before the above two blocking functions. This supports problem determination with scsi_eh and parallel zfcp ERP. No need to explicitly trace the beginning of our eh callback, since we typically can send an abort / TMF and see its HBA response (in the worst case, it's a pseudo response on dismiss all of adapter recovery, e.g. due to an FSF request timeout [fsrth_1] of the abort / TMF). If we cannot send, we now get a trace record for the first "abrt_wt" or "[lt]r_wait" which denotes almost the beginning of the callback. No need to explicitly trace the wakeup after the above two blocking functions because the next retry loop causes another trace in any case and that is sufficient. Example trace records formatted with zfcpdbf from s390-tools: Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : abrt_wt abort, before zfcp_erp_wait() Request ID : 0x0000000000000000 none (invalid) SCSI ID : 0x<scsi_id> SCSI LUN : 0x<scsi_lun> SCSI LUN high : 0x<scsi_lun_high> SCSI result : 0x<scsi_result_of_cmd_to_be_aborted> SCSI retries : 0x<retries_of_cmd_to_be_aborted> SCSI allowed : 0x<allowed_retries_of_cmd_to_be_aborted> SCSI scribble : 0x<req_id_of_cmd_to_be_aborted> SCSI opcode : <CDB_of_cmd_to_be_aborted> FCP rsp inf cod: 0x.. none (invalid) FCP rsp IU : ... none (invalid) Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : lr_wait LUN reset, before zfcp_erp_wait() Request ID : 0x0000000000000000 none (invalid) SCSI ID : 0x<scsi_id> SCSI LUN : 0x<scsi_lun> SCSI LUN high : 0x<scsi_lun_high> SCSI result : 0x... unrelated SCSI retries : 0x.. unrelated SCSI allowed : 0x.. unrelated SCSI scribble : 0x... unrelated SCSI opcode : ... unrelated FCP rsp inf cod: 0x.. none (invalid) FCP rsp IU : ... none (invalid) Signed-off-by:
-
Steffen Maier authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit df307816 upstream. For problem determination we need to see whether and why we were successful or not. This allows deduction of scsi_eh escalation. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : schrh_r SCSI host reset handler result Request ID : 0x0000000000000000 none (invalid) SCSI ID : 0xffffffff none (invalid) SCSI LUN : 0xffffffff none (invalid) SCSI LUN high : 0xffffffff none (invalid) SCSI result : 0x00002002 field re-used for midlayer value: SUCCESS or in other cases: 0x2009 == FAST_IO_FAIL SCSI retries : 0xff none (invalid) SCSI allowed : 0xff none (invalid) SCSI scribble : 0xffffffffffffffff none (invalid) SCSI opcode : ffffffff ffffffff ffffffff ffffffff none (invalid) FCP rsp inf cod: 0xff none (invalid) FCP rsp IU : 00000000 00000000 00000000 00000000 none (invalid) 00000000 00000000 v2.6.35 commit a1dbfddd ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh") introduced the first return with something other than the previously hardcoded single SUCCESS return path. Signed-off-by:
Jens Remus <jremus@linux.ibm.com> Reviewed-by:
-
Himanshu Madhani authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 413c2f33 upstream. This patch prevents driver from setting lower default speed of 1 GB/sec, if the switch does not support Get Port Speed Capabilities (GPSC) command. Setting this default speed results into much lower write performance for large sequential WRITE. This patch modifies driver to check for gpsc_supported flags and prevents driver from issuing MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver does not send this mailbox command, firmware assumes maximum supported link speed and will operate at the max speed. Cc: stable@vger.kernel.org Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Reported-by:
Eda Zhou <ezhou@redhat.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Tested-by:
-
Martin Kelly authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit c043ec1c upstream. Currently, we use int for buffer length and bytes_per_datum. However, kfifo uses unsigned int for length and size_t for element size. We need to make sure these matches or we will have bugs related to overflow (in the range between INT_MAX and UINT_MAX for length, for example). In addition, set_bytes_per_datum uses size_t while bytes_per_datum is an int, which would cause bugs for large values of bytes_per_datum. Change buffer length to use unsigned int and bytes_per_datum to use size_t. Signed-off-by:
Martin Kelly <mkelly@xevo.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> [bwh: Backported to 4.4: - Drop change to iio_dma_buffer_set_length() - Adjust filename, context] Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Omar Sandoval authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit b5c40d59 upstream. In btrfs_clone_files(), we must check the NODATASUM flag while the inodes are locked. Otherwise, it's possible that btrfs_ioctl_setflags() will change the flags after we check and we can end up with a party checksummed file. The race window is only a few instructions in size, between the if and the locks which is: 3834 if (S_ISDIR(src->i_mode) || S_ISDIR(inode->i_mode)) 3835 return -EISDIR; where the setflags must be run and toggle the NODATASUM flag (provided the file size is 0). The clone will block on the inode lock, segflags takes the inode lock, changes flags, releases log and clone continues. Not impossible but still needs a lot of bad luck to hit unintentionally. Fixes: 0e7b824c ("Btrfs: don't make a file partly checksummed through file clone") CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
Omar Sandoval <osandov@fb.com> Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> [ update changelog ] Signed-off-by:
-
Geert Uytterhoeven authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit abcbcb80 upstream. For the common cases where 1000 is a multiple of HZ, or HZ is a multiple of 1000, jiffies_to_msecs() never returns zero when passed a non-zero time period. However, if HZ > 1000 and not an integer multiple of 1000 (e.g. 1024 or 1200, as used on alpha and DECstation), jiffies_to_msecs() may return zero for small non-zero time periods. This may break code that relies on receiving back a non-zero value. jiffies_to_usecs() does not need such a fix: one jiffy can only be less than one µs if HZ > 1000000, and such large values of HZ are already rejected at build time, twice: - include/linux/jiffies.h does #error if HZ >= 12288, - kernel/time/time.c has BUILD_BUG_ON(HZ > USEC_PER_SEC). Broken since forever. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Stephen Boyd <sboyd@kernel.org> Cc: linux-alpha@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180622143357.7495-1-geert@linux-m68k.orgSigned-off-by:
-
Huacai Chen authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 18f3e95b upstream. While a barrier is present in the outX() functions before the register write, a similar barrier is missing in the inX() functions after the register read. This could allow memory accesses following inX() to observe stale data. This patch is very similar to commit a1cc7034 ("MIPS: io: Add barrier after register read in readX()"). Because war_io_reorder_wmb() is both used by writeX() and outX(), if readX() need a barrier then so does inX(). Cc: stable@vger.kernel.org Signed-off-by:
Huacai Chen <chenhc@lemote.com> Patchwork: https://patchwork.linux-mips.org/patch/19516/Signed-off-by:
Paul Burton <paul.burton@mips.com> Cc: James Hogan <james.hogan@mips.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com> Signed-off-by:
-
Mika Westerberg authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 13c65840 upstream. After a suspend/resume cycle the Presence Detect or Data Link Layer Status Changed bits might be set. If we don't clear them those events will not fire anymore and nothing happens for instance when a device is now hot-unplugged. Fix this by clearing those bits in a newly introduced function pcie_reenable_notification(). This should be fine because immediately after, we check if the adapter is still present by reading directly from the status register. Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Tokunori Ikegami authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 2a027b47 upstream. The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as below. R10: PCIe Transactions Periodically Fail Description: The BCM5300X PCIe does not maintain transaction ordering. This may cause PCIe transaction failure. Fix Comment: Add a dummy PCIe configuration read after a PCIe configuration write to ensure PCIe configuration access ordering. Set ES bit of CP0 configu7 register to enable sync function so that the sync instruction is functional. Resolution: hndpci.c: extpci_write_config() hndmips.c: si_mips_init() mipsinc.h CONF7_ES This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX. Also the dummy PCIe configuration read is already implemented in the Linux BCMA driver. Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y too so that the sync instruction is externalised. Signed-off-by:
Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by:
Hauke Mehrtens <hauke@hauke-m.de> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/19461/Signed-off-by:
James Hogan <jhogan@kernel.org> Signed-off-by:
-
Joakim Tjernlund authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit f1ce87f6 upstream. cfi_ppb_unlock() walks all flash chips when unlocking sectors, avoid walking chips unaffected by the unlock operation. Fixes: 1648eaaa ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by:
Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by:
-
Joakim Tjernlund authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 0cd8116f upstream. The "sector is in requested range" test used to determine whether sectors should be re-locked or not is done on a variable that is reset everytime we cross a chip boundary, which can lead to some blocks being re-locked while the caller expect them to be unlocked. Fix the check to make sure this cannot happen. Fixes: 1648eaaa ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by:
-
Joakim Tjernlund authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 5fdfc3db upstream. cfi_ppb_unlock() tries to relock all sectors that were locked before unlocking the whole chip. This locking used the chip start address + the FULL offset from the first flash chip, thereby forming an illegal address. Fix that by using the chip offset(adr). Fixes: 1648eaaa ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by:
-
Joakim Tjernlund authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit f93aa8c4 upstream. do_ppb_xxlock() fails to add chip->start when querying for lock status (and chip_ready test), which caused false status reports. Fix that by adding adr += chip->start and adjust call sites accordingly. Fixes: 1648eaaa ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by:
-
Tokunori Ikegami authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit dfeae107 upstream. For the word write it is checked if the chip has the correct value. But it is not checked for the write buffer as only checked if ready. To make sure for the write buffer change to check the value. It is enough as this patch is only checking the last written word. Since it is described by data sheets to check the operation status. Signed-off-by:
-
Leon Romanovsky authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 6b1ca7ec upstream. There is no need to crash the machine if unknown work request was received in SQP MAD. Cc: <stable@vger.kernel.org> # 3.6 Fixes: 37bfc7c1 ("IB/mlx4: SR-IOV multiplex and demultiplex MADs") Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Mike Marciniszyn authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 0252f733 upstream. The following error occurs in a debug build when running MPI PSM: [ 307.415911] WARNING: CPU: 4 PID: 23867 at lib/dma-debug.c:1158 check_unmap+0x4ee/0xa20 [ 307.455661] ib_qib 0000:05:00.0: DMA-API: device driver failed to check map error[device address=0x00000000df82b000] [size=4096 bytes] [mapped as page] [ 307.517494] Modules linked in: [ 307.531584] ib_isert iscsi_target_mod ib_srpt target_core_mod rpcrdma sunrpc ib_srp scsi_transport_srp scsi_tgt ib_iser libiscsi ib_ipoib scsi_transport_iscsi rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ib_qib intel_powerclamp coretemp rdmavt intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel ipmi_ssif ib_core aesni_intel sg ipmi_si lrw gf128mul dca glue_helper ipmi_devintf iTCO_wdt gpio_ich hpwdt iTCO_vendor_support ablk_helper hpilo acpi_power_meter cryptd ipmi_msghandler ie31200_edac shpchp pcc_cpufreq lpc_ich pcspkr ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm ahci crct10dif_pclmul crct10dif_common drm crc32c_intel libahci tg3 libata serio_raw ptp i2c_core [ 307.846113] pps_core dm_mirror dm_region_hash dm_log dm_mod [ 307.866505] CPU: 4 PID: 23867 Comm: mpitests-IMB-MP Kdump: loaded Not tainted 3.10.0-862.el7.x86_64.debug #1 [ 307.911178] Hardware name: HP ProLiant DL320e Gen8, BIOS J05 11/09/2013 [ 307.944206] Call Trace: [ 307.956973] [<ffffffffbd9e915b>] dump_stack+0x19/0x1b [ 307.982201] [<ffffffffbd2a2f58>] __warn+0xd8/0x100 [ 308.005999] [<ffffffffbd2a2fdf>] warn_slowpath_fmt+0x5f/0x80 [ 308.034260] [<ffffffffbd5f667e>] check_unmap+0x4ee/0xa20 [ 308.060801] [<ffffffffbd41acaa>] ? page_add_file_rmap+0x2a/0x1d0 [ 308.090689] [<ffffffffbd5f6c4d>] debug_dma_unmap_page+0x9d/0xb0 [ 308.120155] [<ffffffffbd4082e0>] ? might_fault+0xa0/0xb0 [ 308.146656] [<ffffffffc07761a5>] qib_tid_free.isra.14+0x215/0x2a0 [ib_qib] [ 308.180739] [<ffffffffc0776bf4>] qib_write+0x894/0x1280 [ib_qib] [ 308.210733] [<ffffffffbd540b00>] ? __inode_security_revalidate+0x70/0x80 [ 308.244837] [<ffffffffbd53c2b7>] ? security_file_permission+0x27/0xb0 [ 308.266025] qib_ib0.8006: multicast join failed for ff12:401b:8006:0000:0000:0000:ffff:ffff, status -22 [ 308.323421] [<ffffffffbd46f5d3>] vfs_write+0xc3/0x1f0 [ 308.347077] [<ffffffffbd492a5c>] ? fget_light+0xfc/0x510 [ 308.372533] [<ffffffffbd47045a>] SyS_write+0x8a/0x100 [ 308.396456] [<ffffffffbd9ff355>] system_call_fastpath+0x1c/0x21 The code calls a qib_map_page() which has never correctly tested for a mapping error. Fix by testing for pci_dma_mapping_error() in all cases and properly handling the failure in the caller. Additionally, streamline qib_map_page() arguments to satisfy just the single caller. Cc: <stable@vger.kernel.org> Reviewed-by:
Alex Estrin <alex.estrin@intel.com> Tested-by:
Don Dutile <ddutile@redhat.com> Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
-
Stefan M Schaeckeler authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 3b9cf790 upstream. For strings, account for trailing \0 in property length field: This is consistent with how dtc builds string properties. Function __of_prop_dup() would misbehave on such properties as it duplicates properties based on the property length field creating new string values without trailing \0s. Signed-off-by:
Stefan M Schaeckeler <sschaeck@cisco.com> Reviewed-by:
Frank Rowand <frank.rowand@sony.com> Tested-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
David Rivshin authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 76ed0b80 upstream. NUMREGBYTES (which is used as the size for gdb_regs[]) is incorrectly based on DBG_MAX_REG_NUM instead of GDB_MAX_REGS. DBG_MAX_REG_NUM is the number of total registers, while GDB_MAX_REGS is the number of 'unsigned longs' it takes to serialize those registers. Since FP registers require 3 'unsigned longs' each, DBG_MAX_REG_NUM is smaller than GDB_MAX_REGS. This causes GDB 8.0 give the following error on connect: "Truncated register 19 in remote 'g' packet" This also causes the register serialization/deserialization logic to overflow gdb_regs[], overwriting whatever follows. Fixes: 834b2964 ("kgdb,arm: fix register dump") Cc: <stable@vger.kernel.org> # 2.6.37+ Signed-off-by:
David Rivshin <drivshin@allworx.com> Acked-by:
Rabin Vincent <rabin@rab.in> Tested-by:
Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Mahesh Salgaonkar authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 722cde76 upstream. Unregister fadump on kexec down path otherwise the fadump registration in new kexec-ed kernel complains that fadump is already registered. This makes new kernel to continue using fadump registered by previous kernel which may lead to invalid vmcore generation. Hence this patch fixes this issue by un-registering fadump in fadump_cleanup() which is called during kexec path so that new kernel can register fadump with new valid values. Fixes: b500afff ("fadump: Invalidate registration and release reserved memory for general use.") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Gautham R. Shenoy authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 0a4ec6aa upstream. The commit 78eaa10f ("cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state") introduced a timeout for the snooze idle state so that it could be eventually be promoted to a deeper idle state. The snooze timeout value is static and set to the target residency of the next idle state, which would train the cpuidle governor to pick the next idle state eventually. The unfortunate side-effect of this is that if the next idle state(s) is disabled, the CPU will forever remain in snooze, despite the fact that the system is completely idle, and other deeper idle states are available. This patch fixes the issue by dynamically setting the snooze timeout to the target residency of the next enabled state on the device. Before Patch: POWER8 : Only nap disabled. $ cpupower monitor sleep 30 sleep took 30.01297 seconds and exited with status 0 |Idle_Stats PKG |CORE|CPU | snoo | Nap | Fast 0| 8| 0| 96.41| 0.00| 0.00 0| 8| 1| 96.43| 0.00| 0.00 0| 8| 2| 96.47| 0.00| 0.00 0| 8| 3| 96.35| 0.00| 0.00 0| 8| 4| 96.37| 0.00| 0.00 0| 8| 5| 96.37| 0.00| 0.00 0| 8| 6| 96.47| 0.00| 0.00 0| 8| 7| 96.47| 0.00| 0.00 POWER9: Shallow states (stop0lite, stop1lite, stop2lite, stop0, stop1, stop2) disabled: $ cpupower monitor sleep 30 sleep took 30.05033 seconds and exited with status 0 |Idle_Stats PKG |CORE|CPU | snoo | stop | stop | stop | stop | stop | stop | stop | stop 0| 16| 0| 89.79| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00 0| 16| 1| 90.12| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00 0| 16| 2| 90.21| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00 0| 16| 3| 90.29| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00 After Patch: POWER8 : Only nap disabled. $ cpupower monitor sleep 30 sleep took 30.01200 seconds and exited with status 0 |Idle_Stats PKG |CORE|CPU | snoo | Nap | Fast 0| 8| 0| 16.58| 0.00| 77.21 0| 8| 1| 18.42| 0.00| 75.38 0| 8| 2| 4.70| 0.00| 94.09 0| 8| 3| 17.06| 0.00| 81.73 0| 8| 4| 3.06| 0.00| 95.73 0| 8| 5| 7.00| 0.00| 96.80 0| 8| 6| 1.00| 0.00| 98.79 0| 8| 7| 5.62| 0.00| 94.17 POWER9: Shallow states (stop0lite, stop1lite, stop2lite, stop0, stop1, stop2) disabled: $ cpupower monitor sleep 30 sleep took 30.02110 seconds and exited with status 0 |Idle_Stats PKG |CORE|CPU | snoo | stop | stop | stop | stop | stop | stop | stop | stop 0| 0| 0| 0.69| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 9.39| 89.70 0| 0| 1| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.05| 93.21 0| 0| 2| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 89.93 0| 0| 3| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 93.26 Fixes: 78eaa10f ("cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by:
Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by:
Balbir Singh <bsingharora@gmail.com> Signed-off-by:
-
Michael Neuling authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit cd6ef7ee upstream. Back when we first introduced the DAWR, in commit 4ae7ebe9 ("powerpc: Change hardware breakpoint to allow longer ranges"), we screwed up the constraint making it a 1024 byte boundary rather than a 512. This makes the check overly permissive. Fortunately GDB is the only real user and it always did they right thing, so we never noticed. This fixes the constraint to 512 bytes. Fixes: 4ae7ebe9 ("powerpc: Change hardware breakpoint to allow longer ranges") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
Michael Neuling authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 4f7c06e2 upstream. In commit e2a800be ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") we fixed setting the DAWR end point to its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint. PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to zero (memset() in hw_breakpoint_init()). This worked with arch_validate_hwbkpt_settings() before the above patch was applied but is now broken if the breakpoint is 512byte aligned. This sets the length of the breakpoint to 8 bytes when using PTRACE_SET_DEBUGREG. Fixes: e2a800be ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") Cc: stable@vger.kernel.org # v3.11+ Signed-off-by:
-
Aneesh Kumar K.V authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 91d06971 upstream. Currently we do not have an isync, or any other context synchronizing instruction prior to the slbie/slbmte in _switch() that updates the SLB entry for the kernel stack. However that is not correct as outlined in the ISA. From Power ISA Version 3.0B, Book III, Chapter 11, page 1133: "Changing the contents of ... the contents of SLB entries ... can have the side effect of altering the context in which data addresses and instruction addresses are interpreted, and in which instructions are executed and data accesses are performed. ... These side effects need not occur in program order, and therefore may require explicit synchronization by software. ... The synchronizing instruction before the context-altering instruction ensures that all instructions up to and including that synchronizing instruction are fetched and executed in the context that existed before the alteration." And page 1136: "For data accesses, the context synchronizing instruction before the slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures that all preceding instructions that access data storage have completed to a point at which they have reported all exceptions they will cause." We're not aware of any bugs caused by this, but it should be fixed regardless. Add the missing isync when updating kernel stack SLB entry. Cc: stable@vger.kernel.org Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> [mpe: Flesh out change log with more ISA text & explanation] Signed-off-by:
-
Miklos Szeredi authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 6becdb60 upstream. syzbot is reporting NULL pointer dereference at fuse_ctl_remove_conn() [1]. Since fc->ctl_ndents is incremented by fuse_ctl_add_conn() when new_inode() failed, fuse_ctl_remove_conn() reaches an inode-less dentry and tries to clear d_inode(dentry)->i_private field. Fix by only adding the dentry to the array after being fully set up. When tearing down the control directory, do d_invalidate() on it to get rid of any mounts that might have been added. [1] https://syzkaller.appspot.com/bug?id=f396d863067238959c91c0b7cfc10b163638cac6Reported-by:
syzbot <syzbot+32c236387d66c4516827@syzkaller.appspotmail.com> Fixes: bafa9654 ("[PATCH] fuse: add control filesystem") Cc: <stable@vger.kernel.org> # v2.6.18 Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Tetsuo Handa authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 543b8f86 upstream. syzbot is reporting use-after-free at fuse_kill_sb_blk() [1]. Since sb->s_fs_info field is not cleared after fc was released by fuse_conn_put() when initialization failed, fuse_kill_sb_blk() finds already released fc and tries to hold the lock. Fix this by clearing sb->s_fs_info field after calling fuse_conn_put(). [1] https://syzkaller.appspot.com/bug?id=a07a680ed0a9290585ca424546860464dd9658dbSigned-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by:
syzbot <syzbot+ec3986119086fe4eec97@syzkaller.appspotmail.com> Fixes: 3b463ae0 ("fuse: invalidation reverse calls") Cc: John Muir <john@jmuir.com> Cc: Csaba Henk <csaba@gluster.com> Cc: Anand Avati <avati@redhat.com> Cc: <stable@vger.kernel.org> # v2.6.31 Signed-off-by:
-
Miklos Szeredi authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit df0e91d4 upstream. Fuse has an "atomic_o_trunc" mode, where userspace filesystem uses the O_TRUNC flag in the OPEN request to truncate the file atomically with the open. In this mode there's no need to send a SETATTR request to userspace after the open, so fuse_do_setattr() checks this mode and returns. But this misses the important step of truncating the pagecache. Add the missing parts of truncation to the ATTR_OPEN branch. Reported-by:
Chad Austin <chadaustin@fb.com> Fixes: 6ff958ed ("fuse: add atomic open+truncate support") Signed-off-by:
-
Amit Pundir authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 7dc5fe08 upstream. AOSP use userspace firmware loader to load firmwares, which will return -EAGAIN in case qca/rampatch_00440302.bin is not found. Since there is no rampatch for dragonboard820c QCA controller revision, just make it work as is. CC: Loic Poulain <loic.poulain@linaro.org> CC: Nicolas Dechesne <nicolas.dechesne@linaro.org> CC: Marcel Holtmann <marcel@holtmann.org> CC: Johan Hedberg <johan.hedberg@gmail.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Corey Minyard authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit fe50a7d0 upstream. There was one place where the timeout value for an operation was not being set, if a capabilities request was done from idle. Move the timeout value setting to before where that change might be requested. IMHO the cause here is the invisible returns in the macros. Maybe that's a job for later, though. Reported-by:
Nordmark Claes <Claes.Nordmark@tieto.com> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Mikulas Patocka authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 2026d357 upstream. The function __builtin_expect returns long type (see the gcc documentation), and so do macros likely and unlikely. Unfortunatelly, when CONFIG_PROFILE_ANNOTATED_BRANCHES is selected, the macros likely and unlikely expand to __branch_check__ and __branch_check__ truncates the long type to int. This unintended truncation may cause bugs in various kernel code (we found a bug in dm-writecache because of it), so it's better to fix __branch_check__ to return long. Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1805300818140.24812@file01.intranet.prod.int.rdu2.redhat.com Cc: Ingo Molnar <mingo@redhat.com> Cc: stable@vger.kernel.org Fixes: 1f0d69a9 ("tracing: profile likely and unlikely annotations") Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Matthias Schiffer authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 6fb86566 upstream. ftrace_graph_caller was never run after calling ftrace_trace_function, breaking the function graph tracer. Fix this, bringing it in line with the x86 implementation. While we're at it, also streamline the control flow of _mcount a bit to reduce the number of branches. This issue was reported before: https://www.linux-mips.org/archives/linux-mips/2014-11/msg00295.htmlSigned-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Tested-by:
Matt Redfearn <matt.redfearn@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/18929/Signed-off-by:
-
Geert Uytterhoeven authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 666902e4 upstream. "%pCr" formats the current rate of a clock, and calls clk_get_rate(). The latter obtains a mutex, hence it must not be called from atomic context. Remove support for this rarely-used format, as vsprintf() (and e.g. printk()) must be callable from any context. Any remaining out-of-tree users will start seeing the clock's name printed instead of its rate. Reported-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Fixes: 900cca29 ("lib/vsprintf: add %pC{,n,r} format specifiers for clocks") Link: http://lkml.kernel.org/r/1527845302-12159-5-git-send-email-geert+renesas@glider.be To: Jia-Ju Bai <baijiaju1990@gmail.com> To: Jonathan Corbet <corbet@lwn.net> To: Michael Turquette <mturquette@baylibre.com> To: Stephen Boyd <sboyd@kernel.org> To: Zhang Rui <rui.zhang@intel.com> To: Eduardo Valentin <edubezval@gmail.com> To: Eric Anholt <eric@anholt.net> To: Stefan Wahren <stefan.wahren@i2se.com> To: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: linux-doc@vger.kernel.org Cc: linux-clk@vger.kernel.org Cc: linux-pm@vger.kernel.org Cc: linux-serial@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org # 4.1+ Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Petr Mladek <pmladek@suse.com> Signed-off-by:
-
Alexander Sverdlin authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 5d302ed3 upstream. According to "EP93xx User’s Guide", I2STXLinCtrlData and I2SRXLinCtrlData registers actually have different format. The only currently used bit (Left_Right_Justify) has different position. Fix this and simplify the whole setup taking into account the fact that both registers have zero default value. The practical effect of the above is repaired SND_SOC_DAIFMT_RIGHT_J support (currently unused). Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Alexander Sverdlin authored
BugLink: https://bugs.launchpad.net/bugs/1784382 commit 2d534113 upstream. The bit responsible for LRCLK polarity is i2s_tlrs (0), not i2s_trel (2) (refer to "EP93xx User's Guide"). Previously card drivers which specified SND_SOC_DAIFMT_NB_IF actually got SND_SOC_DAIFMT_NB_NF, an adaptation is necessary to retain the old behavior. Signed-off-by:
-
