Currently if ieee802154_if_add failed, we don't unregister the wpan phy
which was registered before. This patch adds a correct error handling
for unregister the wpan phy when ieee802154_if_add failed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Most likely, the shutdown routine requires the interface to be up.
This is the case for BTUSB_INTEL: the routine tries to send a command
to the interface, but since this one is down, it fails and exits once
HCI_INIT_TIMEOUT has expired.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0.x

Commit 6559a7e8 ("cxgb4: Cleanup macros so they follow the same
style and look consistent") introduced a regression where reading MC1
memory in adapters where MC0 isn't present or MC0 size is not equal to MC1
size caused the adapter to crash due to incorrect computation of memoffset.
Fix is to read the size of MC0 instead of MC1 for offset calculation
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a kdump environment interfaces might be re-loaded without a proper
unload sequence in the previous running kernel.
bnx2x management FW and driver maintains a `pulse' that notifies the FW
that the driver is still up and running.

Driver load on the kdump kernel should be performed only after the pulse
has been out-of-sync long enough for the management FW to identify that
the driver has crashed, on which point it will perform some necessary
cleanup of the HW.

In today's distros kdump loading is quite fast, sometimes too fast for our
FW to get out-of-sync. This patch delays the bnx2x's probe during kdump
to allow a proper re-load on the kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a Kernel Panic in bonding driver debugfs file: rlb_hash_table.

$> modprobe bonding mode=6
$> cat /sys/kernel/debug/bonding/bond0/rlb_hash_table

This will crash the kernel. The struct alb_bond_info is initialized only when
the bonding interface is initialized (ip link set bond0 up) and not at the time
it is allocated. If we try to read the table before that, it'll result in a
kernel panic.

The patch applies against both net and net-next
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eeprom-length is a switch property, not a dsa property, and thus
needs to be attached to the switch node, not to the dsa node.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6793abb4 ("net: dsa: Add support for switch EEPROM access")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under heavy Rx load, observed that the Hw is updating the USED bit
and it is not updating the received frame status to the BD control
field. This could be lack of resources for processing the BDs at high
data rates. Driver drops the frame associated with this BD but not
clearing the USED bit. So, this is causing hang condition as Hw
expects USED bit to be cleared for this BD.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b08cc791 eliminated memory
allocation in the packet send path:

    "hv_netvsc: Eliminate memory allocation in the packet send path

    The network protocol used to communicate with the host is the remote ndis (rndis)
    protocol. We need to decorate each outgoing packet with a rndis header and
    additional rndis state (rndis per-packet state). To manage this state, we
    currently allocate memory in the transmit path. Eliminate this allocation by
    requesting additional head room in the skb."

This commit introduced a bug since it did not account for the case if the skb
was cloned. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Altera TSE MAC rx DMA transfer starts with the 2 additional bytes for IP
payload alignment. This patch fixes tse_rx() function loop which reads DMA
rx status and extracts packet length from it. Status signalises a whole DMA
transfer length, which is 2 bytes longer than the packet itself.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

By default, the number of tx queues is limited by the number of online cpus
in mlx4_en_get_profile(). However, this limit no longer holds after the
ethtool .set_channels method has been called. In that situation, the driver
may access invalid bits of certain cpumask variables when queue_index >=
nr_cpu_ids.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Ido Shamay <idos@mellanox.com>
Fixes: d03a68f8 ("net/mlx4_en: Configure the XPS queue mapping on driver load")
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we try to accumulate arrived packets in the links's
'deferred' queue during the parallel link syncronization phase.

This entails two problems:

- With an unlucky combination of arriving packets the algorithm
  may go into a lockstep with the out-of-sequence handling function,
  where the synch mechanism is adding a packet to the deferred queue,
  while the out-of-sequence handling is retrieving it again, thus
  ending up in a loop inside the node_lock scope.

- Even if this is avoided, the link will very often send out
  unnecessary protocol messages, in the worst case leading to
  redundant retransmissions.

We fix this by just dropping arriving packets on the upcoming link
during the synchronization phase, thus relying on the retransmission
protocol to resolve the situation once the two links have arrived to
a synchronized state.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.

Libraries like libnl will wait forever for NLMSG_DONE.

Fixes: 35b9dd76 ("tipc: add bearer get/dump to new netlink api")
Fixes: 7be57fc6 ("tipc: add link get/dump to new netlink api")
Fixes: 46f15c67 ("tipc: add media get/dump to new netlink api")
CC: Richard Alpe <richard.alpe@ericsson.com>
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.

Libraries like libnl will wait forever for NLMSG_DONE.

Fixes: e5a55a89 ("net: create generic bridge ops")
Fixes: 815cccbf ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.

Libraries like libnl will wait forever for NLMSG_DONE.

Fixes: 37a393bc ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This action is meant to be passive, i.e. we should not alter
skb->nfct: If nfct is present just leave it alone.

Compile tested only.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the 0x0x prefix in an integer constant.

In this case, while at it, also fix a typo (s/unitcast/unicast/).
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the 0x0x prefix in an integer constant.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Schmidt says:

====================
bnx2x: minor cleanups related to TPA bits

I noticed some simplification possibilities while looking into the bug
fixed by "bnx2x: really disable TPA if 'disable_tpa' is set'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is simpler to have the TPA mode as one three-state variable.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If disable_tpa is set, remove NETIF_F_LRO from hw_features, so ethtool sees
it as "off [fixed]".

Note that setting the NETIF_F_LRO bit in dev->features in the 'else'
branch is not needed, because the bit was already set by
bnx2x_init_dev().

Then the check for disable_tpa in in bnx2x_fix_features() becomes unnecessary.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Introduce netif-msg to netvsc to control debug logging output
and keep msg_enable in netvsc_device_context so that it is
kept persistently.
2. Only call dump_rndis_message() when NETIF_MSG_RX_ERR or above
is specified in netvsc module debug param.
In non-debug mode, in current code, dump_rndis_message() will not
dump anything but it still initialize some local variables and
process the switch logic which is unnecessary, especially in
high network throughput situation.
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 3cdaa5be ("ipv4: Don't
increase PMTU with Datagram Too Big message") broke PMTU in cases
where the rt_pmtu value has expired but is smaller than the new
PMTU value.

This obsolete rt_pmtu then prevents the new PMTU value from being
installed.

Fixes: 3cdaa5be ("ipv4: Don't increase PMTU with Datagram Too Big message")
Reported-by: Gerd v. Egidy <gerd.von.egidy@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Fix a crash in nf_tables when dictionaries are used from the ruleset,
   due to memory corruption, from Florian Westphal.

2) Fix another crash in nf_queue when used with br_netfilter. Also from
   Florian.

Both fixes are related to new stuff that got in 4.0-rc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ALU64_DIV instruction should be dividing 64-bit by 64-bit,
whereas do_div() does 64-bit by 32-bit divide.
x64 and arm64 JITs correctly implement 64 by 64 unsigned divide.
llvm BPF backend emits code assuming that ALU64_DIV does 64 by 64.

Fixes: 89aa0758 ("net: sock: allow eBPF programs to be attached to sockets")
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when interface type is MAC to Phy, netif_carrier_(on/off)
is called which is not needed as Phy lib already updates the carrier
status to net stack. This is needed only for other interface types
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) mlx4 doesn't check fully for supported valid RSS hash function, fix
    from Amir Vadai

 2) Off by one in ibmveth_change_mtu(), from David Gibson

 3) Prevent altera chip from reporting false error interrupts in some
    circumstances, from Chee Nouk Phoon

 4) Get rid of that stupid endless loop trying to allocate a FIN packet
    in TCP, and in the process kill deadlocks.  From Eric Dumazet

 5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
    Eric Dumazet

 6) Fix two bugs in async rhashtable resizing, from Thomas Graf

 7) Fix topology server listener socket namespace bug in TIPC, from Ying
    Xue

 8) Add some missing HAS_DMA kconfig dependencies, from Geert
    Uytterhoeven

 9) bgmac driver intends to force re-polling but does so by returning
    the wrong value from it's ->poll() handler.  Fix from Rafał Miłecki

10) When the creater of an rhashtable configures a max size for it,
    don't bark in the logs and drop insertions when that is exceeded.
    Fix from Johannes Berg

11) Recover from out of order packets in ppp mppe properly, from Sylvain
    Rochet

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  bnx2x: really disable TPA if 'disable_tpa' option is set
  net:treewide: Fix typo in drivers/net
  net/mlx4_en: Prevent setting invalid RSS hash function
  mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
  netfilter; Add some missing default cases to switch statements in nft_reject.
  ppp: mppe: discard late packet in stateless mode
  ppp: mppe: sanity error path rework
  net/bonding: Make DRV macros private
  net: rfs: fix crash in get_rps_cpus()
  altera tse: add support for fixed-links.
  pxa168: fix double deallocation of managed resources
  net: fix crash in build_skb()
  net: eth: altera: Resolve false errors from MSGDMA to TSE
  ehea: Fix memory hook reference counting crashes
  net/tg3: Release IRQs on permanent error
  net: mdio-gpio: support access that may sleep
  inet: fix possible panic in reqsk_queue_unlink()
  rhashtable: don't attempt to grow when at max_size
  bgmac: fix requests for extra polling calls from NAPI
  tcp: avoid looping in tcp_send_fin()
  ...

bnx2x's 'disable_tpa=1' module option is not respected properly and TPA
(transparent packet aggregation) remains enabled. Even though the
module option causes LRO to be disabled, TPA is enabled in GRO mode.

Additionally, disabling GRO via ethtool then has no effect. One can
still observe tpa_* statistics increase and large packets being received
in tcpdump.

The bug was an unintended consequence of commit aebf6244 "bnx2x: Be
more forgiving toward SW GRO".

Fix it by following the bp->disable_tpa flag when initializing fp's.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix spelling typo in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_check_rxfh_func() was checking for hardware support before
setting a known RSS hash function, but didn't do any check before
setting unknown RSS hash function. Need to make it fail on such values.
In this occasion, moved the actual setting of the new value from the
check function into mlx4_en_set_rxfh().

Fixes: 947cbb0a ("net/mlx4_en: Support for configurable RSS hash function")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new gpiod_get_array and gpiod_put_array functions
(added to mainline in the v4.1 merge window) for obtaining and
disposing of GPIO descriptors.

Cc: David Miller <davem@davemloft.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes:

====================
net/netfilter/nft_reject.c: In function ‘nft_reject_dump’:
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswitch]
  switch (priv->type) {
  ^
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_ICMPX_UNREACH’ not handled in switch [-Wswi\
tch]
net/netfilter/nft_reject_inet.c: In function ‘nft_reject_inet_dump’:
net/netfilter/nft_reject_inet.c:105:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswi\
tch]
  switch (priv->type) {
  ^
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sylvain Rochet says:

====================
ppp: mppe: fixes MPPE desync on links which don't guarantee packet ordering

I am currently having an issue with PPP over L2TP (UDP) and MPPE in
stateless mode (default mode), UDP does not guarantee packet ordering so
we might get out of order packet. MPPE needs to be continuously synched
so we should drop late UDP packet.

I added a printk on the number of time we rekeyed in MPPE decompressor,
this is what we currently have if we receive a slightly out of order UDP
packet:

[1731001.049206] mppe_decompress[1]: ccount 1559
[1731001.049216] mppe_decompress[1]: rekeyed 1 times

[1731001.049228] mppe_decompress[1]: ccount 1560
[1731001.049232] mppe_decompress[1]: rekeyed 1 times

[1731001.050170] mppe_decompress[1]: ccount 1562
[1731001.050182] mppe_decompress[1]: rekeyed 2 times

[1731001.050191] mppe_decompress[1]: ccount 1561
[1731001.062576] mppe_decompress[1]: rekeyed 4095 times
                                             ^^^^
This is obviously wrong, we missed packet 1561 and we already rekeyed 2
times for 1562 we previously received, we can't recover the decryption
key we need for 1561, we should drop it instead of rekeying 4095 times.

This patch series drop any packet with are not within the 4096/2 forward
window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When PPP is used over a link which does not guarantee packet ordering,
we might get late MPPE packets. This is a problem because MPPE must be
kept synchronized and the current implementation does not drop them and
rekey 4095 times instead of 0, which is wrong.

In order to prevent rekeying about a whole count space times (~ 4095
times), drop packets which are not within the forward 4096/2 window and
increase sanity error counter.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are going to need sanity error path a little further, rework to be
able to use the sanity error path anywhere in decompressor.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bonding modules currently defines four macros with
general names that pollute the global namespace:
DRV_VERSION
DRV_RELDATE
DRV_NAME
DRV_DESCRIPTION

Fixing that by defining a private bonding_priv.h
header files which includes those defines.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.

Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.

This was exposed by a recent vDSO cleanup.

Fixes: e7d6eefa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull intel drm fixes from Dave Airlie.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull intel iommu updates from David Woodhouse:
 "This lays a little of the groundwork for upcoming Shared Virtual
  Memory support — fixing some bogus #defines for capability bits and
  adding the new ones, and starting to use the new wider page tables
  where we can, in anticipation of actually filling in the new fields
  therein.

  It also allows graphics devices to be assigned to VM guests again.
  This got broken in 3.17 by disallowing assignment of RMRR-afflicted
  devices.  Like USB, we do understand why there's an RMRR for graphics
  devices — and unlike USB, it's actually sane.  So we can make an
  exception for graphics devices, just as we do USB controllers.

  Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
  persistent requests.  X2APIC_OPT_OUT was added to the spec as a nasty
  hack to allow broken BIOSes to forbid us from using X2APIC when they
  do stupid and invasive things and would break if we did.

  Someone noticed that since Windows doesn't have full IOMMU support for
  DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
  initialising the IOMMU on the graphics unit altogether.

  This means that it would be available for use in "driver mode", where
  the IOMMU registers are made available through a BAR of the graphics
  device and the graphics driver can do SVM all for itself.

  So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
  SVM capabilities.  And even the platforms which *might*, if the
  planets had been aligned correctly, possibly have had SVM capability
  but which in practice actually don't"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: support extended root and context entries
  iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
  iommu/vt-d: Allow RMRR on graphics devices too
  iommu/vt-d: Print x2apic opt out info instead of printing a warning
  iommu/vt-d: kill bogus ecap_niotlb_iunits()