This is needed to make rave-sp-eeprom driver work on "legacy"
firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Relying on serial port defaults for flow control and parity can result
in complete breakdown of communication with RAVE SP on some platforms
where defaults are not what we need them to be. One such case is
VF610-base ZII SPU3 board (not supported upstream). To avoid this
problem in the future, add code to explicitly configure both.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

RAVE SP firmware covered by "legacy" variant uses 16-bit CCITT
checksum algorithm. Change the code to correctly reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove unusded defines that are a leftover from earlier iterations of
the driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fixes https://bugs.linaro.org/show_bug.cgi?id=3903

LTP Functional tests have caused a bad paging request when triggering
the regmap_read_debugfs() logic of the device PMIC Hi6553 (reading
regmap/f8000000.pmic/registers file during read_all test):

Unable to handle kernel paging request at virtual address ffff0
[ffff00000984e000] pgd=0000000077ffe803, pud=0000000077ffd803,0
Internal error: Oops: 96000007 [#1] SMP
...
Hardware name: HiKey Development Board (DT)
...
Call trace:
 regmap_mmio_read8+0x24/0x40
 regmap_mmio_read+0x48/0x70
 _regmap_bus_reg_read+0x38/0x48
 _regmap_read+0x68/0x170
 regmap_read+0x50/0x78
 regmap_read_debugfs+0x1a0/0x308
 regmap_map_read_file+0x48/0x58
 full_proxy_read+0x68/0x98
 __vfs_read+0x48/0x80
 vfs_read+0x94/0x150
 SyS_read+0x6c/0xd8
 el0_svc_naked+0x30/0x34
Code: aa1e03e0 d503201f f9400280 8b334000 (39400000)

Investigations have showed that, when triggered by debugfs read()
handler, the mmio regmap logic was reading a bigger (16k) register area
than the one mapped by devm_ioremap_resource() during hi655x-pmic probe
time (4k).

This commit changes hi655x's max register, according to HW specs, to be
the same as the one declared in the pmic device in hi6220's dts, fixing
the issue.

Cc: <stable@vger.kernel.org> #v4.9 #v4.14 #v4.16 #v4.17
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_elk_get() to let Linux manage struct clk memory to avoid the following
memory leakage report:

unreferenced object 0xdd75efc0 (size 64):
  comm "systemd-udevd", pid 186, jiffies 4294945126 (age 1195.750s)
  hex dump (first 32 bytes):
    61 64 63 5f 74 73 63 5f 66 63 6b 00 00 00 00 00  adc_tsc_fck.....
    00 00 00 00 92 03 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<c0a15260>] kmemleak_alloc+0x40/0x74
    [<c0287a10>] __kmalloc_track_caller+0x198/0x388
    [<c0255610>] kstrdup+0x40/0x5c
    [<c025565c>] kstrdup_const+0x30/0x3c
    [<c0636630>] __clk_create_clk+0x60/0xac
    [<c0630918>] clk_get_sys+0x74/0x144
    [<c0630cdc>] clk_get+0x5c/0x68
    [<bf0ac540>] ti_tscadc_probe+0x260/0x468 [ti_am335x_tscadc]
    [<c06f3c0c>] platform_drv_probe+0x60/0xac
    [<c06f1abc>] driver_probe_device+0x214/0x2dc
    [<c06f1c18>] __driver_attach+0x94/0xc0
    [<c06efe2c>] bus_for_each_dev+0x90/0xa0
    [<c06f1470>] driver_attach+0x28/0x30
    [<c06f1030>] bus_add_driver+0x184/0x1ec
    [<c06f2b74>] driver_register+0xb0/0xf0
    [<c06f3b4c>] __platform_driver_register+0x40/0x54
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch fixes documentation of tps65911 because its list of
compatible regulators contains wrongly vdd3 instead of vdd2.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Some Arizona CODECs have a small timing window where they will
NAK an I2C transaction if it happens before the boot done bit is
set. This can cause the read of the register containing the boot
done bit to fail until it is set. Since regmap_read_poll_timeout
will abort polling if a read fails it can't be reliably used to
poll the boot done bit over I2C.

Do a partial revert of ef84f885 ("mfd: arizona: Refactor
arizona_poll_reg"), removing the regmap_read_poll_timeout but
leaving the refactoring to make the arizona_poll_reg take more
sensible arguments.

Fixes: ef84f885 ("mfd: arizona: Refactor arizona_poll_reg")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Intel Ice Lake has the same LPSS than Intel Cannon Lake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

For some errors, the wm8994_device_init function was returning or
jumping to the wrong point in the error path.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add const to the declaration of various local variables of type
kempld_platform_data for which the referenced value is always only
dereferenced or passed to a const parameter, to record the fact that
kempld_platform_data_generic is declared as const.

The semantic match that finds this issue is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier i,j;
@@
const struct i j = { ... };

@ok@
identifier r.i;
position p;
@@
const struct i@p *

@@
identifier r.i;
position p != ok.p;
@@
* struct i@p *
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged

Immutable branch (mfd, chrome) due for the v4.19 window

Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.

The ChromeOS Embedded Controller can expose a CEC bus, this patch add the
driver for such feature of the Embedded Controller.

This driver is part of the cros-ec MFD and will be add as a sub-device when
the feature bit is exposed by the EC.

The controller will only handle a single logical address and handles
all the messages retries and will only expose Success or Error.

The controller will be tied to the HDMI CEC notifier by using the platform
DMI Data and the i915 device name and connector name.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The EC can expose a CEC bus, thus add the cros-ec-cec MFD sub-device
when the CEC feature bit is present.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The EC can expose a CEC bus, this patch adds the CEC related definitions
needed by the cros-ec-cec driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Having a 16 byte mkbp event size makes it possible to send CEC
messages from the EC to the AP directly inside the mkbp event
instead of first doing a notification and then a read.
Signed-off-by: Stefan Adolfsson <sadolfsson@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patchs adds the cec_notifier feature to the intel_hdmi part
of the i915 DRM driver. It uses the HDMI DRM connector name to differentiate
between each HDMI ports.
The changes will allow the i915 HDMI code to notify EDID and HPD changes
to an eventual CEC adapter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

In non device-tree world, we can need to get the notifier by the driver
name directly and eventually defer probe if not yet created.

This patch adds a variant of the get function by using the device name
instead and will not create a notifier if not yet created.

But the i915 driver exposes at least 2 HDMI connectors, this patch also
adds the possibility to add a connector name tied to the notifier device
to form a tuple and associate different CEC controllers for each HDMI
connectors.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for DA9063L, which is a reduced variant of the DA9063
with less regulators and without RTC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move the LDOs present only on DA9063 at the end of the list, so that
the DA9063L can simply indicate less LDOs and still share the list of
regulators with DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The DA9063L does not contain RTC block, unlike the full DA9063.
Split the RTC block into separate mfd cell and register it only
on DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The DA9063L does not have an RTC. Add custom IRQ map for DA9063L to
ignore the Alarm and Tick IRQs from the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The DA9063L does not have an RTC. Add custom regmap for DA9063L to
prevent access into that register block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add type for DA9063L, which is a reduced variant of the DA9063
without RTC block and with less regulators.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The model number stored in the struct da9063 is the same for all
variants of the da9063 since it is the chip ID, which is always
the same. Replace that with a separate identifier instead, which
allows us to discern the DA9063 variants by setting the type
based on either DT match or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The PMIC_DA9063 is a complete misnomer, it denotes the value of the
DA9063 chip ID register, so rename it as such. It is also the value
of chip ID register of DA9063L though, so drop the enum as all the
DA9063 "models" share the same chip ID and thus the distinction will
have to be made using DT or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Replace DA9063_NUM_IRQ macro which is not used anywhere with
plain ARRAY_SIZE().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use PLATFORM_DEVID_NONE instead of -1 in mfd_add_devices.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the regmap_irq table to use REGMAP_IRQ_REG().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Convert the regmap_range tables to use regmap_reg_range() macro.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_mfd_add_devices() instead of plain mfd_add_devices(), which
removes the need for da9063_device_exit() altogether and also for the
.remove callback in da9063-i2c.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_regmap_add_irq_chip() instead of plain regmap_add_irq_chip(),
which removes the need for da9063_irq_exit() altogether and also
fixes a bug in da9063_device_init() where the da9063_irq_exit() was
not called in a failpath.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Check whether this EC instance has USBPD host command support and
instatiate the cros_usbpd-charger driver as a subdevice in such case.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The USBPD charger driver gets information from the ChromeOS EC, this
patch adds the USBPD charger definitions needed by this driver.
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The cros-ec I2C and SPI transport drivers have been moved from MFD
subsystem to platform/chrome, at the same time, the config symbol
has been renamed and lost the MFD_ prefix So, update the help message
accordingly.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>

The cros-ec I2C and SPI transport drivers have been moved from MFD
subsystem to platform/chrome, at the same time, the config symbol has
been renamed and lost the MFD_ prefix, so update all configs to the new
config symbol name.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>

There are some cros-ec transport drivers (I2C, SPI) living in MFD, while
others (LPC) living in drivers/platform. The transport drivers are more
platform specific. So, move the I2C and SPI transport drivers to the
platform/chrome directory. The patch also removes the MFD_ prefix of
their Kconfig symbols.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>

Pull btrfs fixes from David Sterba:
 "We have a few regression fixes for qgroup rescan status tracking and
  the vm_fault_t conversion that mixed up the error values"

* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix mount failure when qgroup rescan is in progress
  Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
  btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf