- 24 Nov, 2012 6 commits
-
-
Andrew Lunn authored
Also enable the gpio-poweroff driver when DT is used. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jamie Lentin authored
Given appropriate devicetree bindings, this driver registers a pm_power_off function to set a GPIO line high/low to power down your board. Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jamie Lentin authored
The default chip-delay of 25us is a bit too tight for some DNS-320's, and D-Link seem to specify 30us in their kernels for both devices. Increase to 35us to make sure the NAND is stable. Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Andrew Lunn authored
Now that the EHCI driver has DT support, drop old style configuration of it and add DT in its place. Since all the boards enable the EHCI, enable it by default in kirkwood.dtsi. Any new boards which don't have USB can specifically disable it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Andrew Lunn authored
Based on previous work by Michael Walle and Jason Cooper. Made their work actually work, which required added interrupt from DT and auxdata, along with setting the dma_mask, which DT does not currently do. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jason Cooper authored
merge pinctrl/devel up to: 06763c74 pinctrl: mvebu: move to its own directory
-
- 22 Nov, 2012 1 commit
-
-
Nobuhiro Iwamatsu authored
Add support for Plat'Home OpenBlocks A6 using the device tree where possible. This commit supports SATA, USB, ether and serial console. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
- 21 Nov, 2012 16 commits
-
-
Sebastian Hesselbarth authored
It has been a while since dove_defconfig was updated to recent development. This patch adds all currently available Dove boards, including a DT-enabled machine. DT support requires to allow ATAGS passed by boot loader as most of them are not yet capable of passing DT blobs. Also OF_SERIAL is enabled to actually see the bootlog. Finally, sdhci driver for Dove, mv_cesa, GPIO LEDs, and highmem support is added. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jason Cooper authored
MPLCEC4_DT is relocated because it had been added manually. Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Thomas Petazzoni authored
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Thomas Petazzoni authored
This commit converts the 'LaCie Ethernet Disk mini v2' board to the Device Tree. All devices that have existing Device Tree bindings are converted over to the Device Tree, the other devices remain instantiated in the old way, until the respective drivers get the needed Device Tree bindings. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Thomas Petazzoni authored
This commit adds basic DT support for the Orion5x SoC family. It adds an orion5x.dtsi description of the Orion5x SoC as well as the needed DT_MACHINE structure to support boards converted to DT in the future. So far, the Device Tree contains the interrupt controller, the GPIO bank, the UART controllers, the SPI controller, the watchdog, the SATA controller, the I2C controller and the cryptographic engine. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Thomas Petazzoni authored
This commit is a simple mechanical update of the orion5x_defconfig file to the current kernel (i.e, just 'make orion5x_defconfig; make savedefconfig'). Doing this update allows to more easily separate DT-related configuration changes in the following patches. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Stefan Peter authored
Signed-off-by: Stefan Peter <s.peter@mpl.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Tero Jaasko authored
Hello, Andrew > > +#define NSA310_GPIO_LED_ESATA_GREEN 12 > > <..> > > +#define NSA310_GPIO_POWER_OFF 48 > > It looks like most of these are not used. Please remove them. True. Fixed. > > +static struct mtd_partition nsa310_mtd_parts[] = { > > + { > > + .name = "uboot", > > + .offset = 0, > > + .size = 0x100000, > > + .mask_flags = MTD_WRITEABLE, > > + }, { > > <..> > You should be able to put all that into DT. Take a look at Correct. I did the conversion and tested that the partitions can be read with dd and produce exactly the same data before and after conversion. So, the partition offsets at least should be fine. > > +static struct i2c_board_info __initdata nsa310_i2c_info[] = { > > + { I2C_BOARD_INFO("adt7476", 0x2e) }, > > +}; > > You can also do this in DT as well. kirkwood-ts219.dtsi has > > i2c@11000 { > status = "okay"; > clock-frequency = <400000>; Ok, I did convert the i2c definition to use the devicetree. The adt7476 device itself is not at reach of device tree, AFAIK and requires more work at there? Thanks for your valuable comments. Following is a new patch that should address the problems and mistakes you pointed and also some of the pointed by Jason Cooper. The nand and i2c are now defined at DT and I also removed the pointless defines and ARM_APPENDED_DTB. It is based against the Linus' official 3.6 version. Best regards, Tero Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jason Cooper authored
This is a new kirkwood box made by Universal Scientific Industrial, Inc. The product description is here: http://www.usish.com/english/products_topkick1281p2.php It is very similar to the dreamplug and other plug devices, with the exception that it has room for a 2.5" SATA HDD internally. Signed-off-by: Jason Cooper <jason@lakedaemon.net> Acked-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
-
Michael Walle authored
Remove board specific gpio-fan driver registration. Moved into device tree. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jason Cooper authored
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Simon Guinot authored
This patch adds DT board setup for the LaCie NAS Network Space Mini v2 (aka SafeBox). The hardware characteristics are very close to those of the Network Space Lite v2. The main difference are: - A GPIO fan which is only available on the NS2 Mini. - A single USB host port is wired on the NS2 Mini. The NS2 Lite provides an additional dual-mode USB port (host/device). Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Simon Guinot authored
This patch adds DT board setup for the LaCie NAS Network Space Lite v2. This board is derived from the Network Space v2 and a lot of hardware characteristics are shared. - CPU: Marvell 88F6192 800Mhz - SDRAM memory: 128MB DDR2 200Mhz - 1 SATA port: internal - Gigabit ethernet: PHY Marvell 88E1318 - Flash memory: SPI NOR 512KB (Macronix MX25L4005A) - i2c EEPROM: 512 bytes (24C04 type) - 2 USB2 ports: host and host/device - 1 push button - 1 SATA LED (bi-color, blue and red) Note that the SATA LED is not compatible with the driver leds-ns2. The LED behaviour ("on", "off" or "SATA activity blink") is controlled via a single MPP (21). Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Simon Guinot authored
This patch adds DT board setup for LaCie Network Space v2 and parents, based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2 (Max) and Internet Space v2. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Simon Guinot authored
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
Jason Gunthorpe authored
mv64xxx_of_config requires that the tclk frequency be found through the clk stuff rather than through device tree, so add another override for the 2nd controller. Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-
- 17 Nov, 2012 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM fix from Marcelo Tosatti: "A correction for oops on module init with older Intel hosts." * git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: Fix invalid secondary exec controls in vmx_cpuid_update()
-
- 16 Nov, 2012 15 commits
-
-
Linus Torvalds authored
Merge misc fixes from Andrew Morton. * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches) revert "mm: fix-up zone present pages" tmpfs: change final i_blocks BUG to WARNING tmpfs: fix shmem_getpage_gfp() VM_BUG_ON mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures" rapidio: fix kernel-doc warnings swapfile: fix name leak in swapoff memcg: fix hotplugged memory zone oops mips, arc: fix build failure memcg: oom: fix totalpages calculation for memory.swappiness==0 mm: fix build warning for uninitialized value mm: add anon_vma_lock to validate_mm()
-
Andrew Morton authored
Revert commit 7f1290f2 ("mm: fix-up zone present pages") That patch tried to fix a issue when calculating zone->present_pages, but it caused a regression on 32bit systems with HIGHMEM. With that change, reset_zone_present_pages() resets all zone->present_pages to zero, and fixup_zone_present_pages() is called to recalculate zone->present_pages when the boot allocator frees core memory pages into buddy allocator. Because highmem pages are not freed by bootmem allocator, all highmem zones' present_pages becomes zero. Various options for improving the situation are being discussed but for now, let's return to the 3.6 code. Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Jiang Liu <jiang.liu@huawei.com> Cc: Petr Tesarik <ptesarik@suse.cz> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Acked-by: David Rientjes <rientjes@google.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Hugh Dickins authored
Under a particular load on one machine, I have hit shmem_evict_inode()'s BUG_ON(inode->i_blocks), enough times to narrow it down to a particular race between swapout and eviction. It comes from the "if (freed > 0)" asymmetry in shmem_recalc_inode(), and the lack of coherent locking between mapping's nrpages and shmem's swapped count. There's a window in shmem_writepage(), between lowering nrpages in shmem_delete_from_page_cache() and then raising swapped count, when the freed count appears to be +1 when it should be 0, and then the asymmetry stops it from being corrected with -1 before hitting the BUG. One answer is coherent locking: using tree_lock throughout, without info->lock; reasonable, but the raw_spin_lock in percpu_counter_add() on used_blocks makes that messier than expected. Another answer may be a further effort to eliminate the weird shmem_recalc_inode() altogether, but previous attempts at that failed. So far undecided, but for now change the BUG_ON to WARN_ON: in usual circumstances it remains a useful consistency check. Signed-off-by: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Hugh Dickins authored
Fuzzing with trinity hit the "impossible" VM_BUG_ON(error) (which Fedora has converted to WARNING) in shmem_getpage_gfp(): WARNING: at mm/shmem.c:1151 shmem_getpage_gfp+0xa5c/0xa70() Pid: 29795, comm: trinity-child4 Not tainted 3.7.0-rc2+ #49 Call Trace: warn_slowpath_common+0x7f/0xc0 warn_slowpath_null+0x1a/0x20 shmem_getpage_gfp+0xa5c/0xa70 shmem_fault+0x4f/0xa0 __do_fault+0x71/0x5c0 handle_pte_fault+0x97/0xae0 handle_mm_fault+0x289/0x350 __do_page_fault+0x18e/0x530 do_page_fault+0x2b/0x50 page_fault+0x28/0x30 tracesys+0xe1/0xe6 Thanks to Johannes for pointing to truncation: free_swap_and_cache() only does a trylock on the page, so the page lock we've held since before confirming swap is not enough to protect against truncation. What cleanup is needed in this case? Just delete_from_swap_cache(), which takes care of the memcg uncharge. Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Dave Jones <davej@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Will Deacon authored
kmap_to_page returns the corresponding struct page for a virtual address of an arbitrary mapping. This works by checking whether the address falls in the pkmap region and using the pkmap page tables instead of the linear mapping if appropriate. Unfortunately, the bounds checking means that PKMAP_ADDR(LAST_PKMAP) is incorrectly treated as a highmem address and we can end up walking off the end of pkmap_page_table and subsequently passing junk to pte_page. This patch fixes the bound check to stay within the pkmap tables. Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Mel Gorman authored
Jiri Slaby reported the following: (It's an effective revert of "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures".) Given kswapd had hours of runtime in ps/top output yesterday in the morning and after the revert it's now 2 minutes in sum for the last 24h, I would say, it's gone. The intention of the patch in question was to compensate for the loss of lumpy reclaim. Part of the reason lumpy reclaim worked is because it aggressively reclaimed pages and this patch was meant to be a sane compromise. When compaction fails, it gets deferred and both compaction and reclaim/compaction is deferred avoid excessive reclaim. However, since commit c6543459 ("mm: remove __GFP_NO_KSWAPD"), kswapd is woken up each time and continues reclaiming which was not taken into account when the patch was developed. Attempts to address the problem ended up just changing the shape of the problem instead of fixing it. The release window gets closer and while a THP allocation failing is not a major problem, kswapd chewing up a lot of CPU is. This patch reverts commit 83fde0f2 ("mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures") and will be revisited in the future. Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: Zdenek Kabelac <zkabelac@redhat.com> Tested-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Randy Dunlap authored
Fix rapidio kernel-doc warnings: Warning(drivers/rapidio/rio.c:415): No description found for parameter 'local' Warning(drivers/rapidio/rio.c:415): Excess function parameter 'lstart' description in 'rio_map_inb_region' Warning(include/linux/rio.h:290): No description found for parameter 'switches' Warning(include/linux/rio.h:290): No description found for parameter 'destid_table' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Matt Porter <mporter@kernel.crashing.org> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Xiaotian Feng authored
There's a name leak introduced by commit 91a27b2a ("vfs: define struct filename and have getname() return it"). Add the missing putname. [akpm@linux-foundation.org: cleanup] Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Hugh Dickins authored
When MEMCG is configured on (even when it's disabled by boot option), when adding or removing a page to/from its lru list, the zone pointer used for stats updates is nowadays taken from the struct lruvec. (On many configurations, calculating zone from page is slower.) But we have no code to update all the lruvecs (per zone, per memcg) when a memory node is hotadded. Here's an extract from the oops which results when running numactl to bind a program to a newly onlined node: BUG: unable to handle kernel NULL pointer dereference at 0000000000000f60 IP: __mod_zone_page_state+0x9/0x60 Pid: 1219, comm: numactl Not tainted 3.6.0-rc5+ #180 Bochs Bochs Process numactl (pid: 1219, threadinfo ffff880039abc000, task ffff8800383c4ce0) Call Trace: __pagevec_lru_add_fn+0xdf/0x140 pagevec_lru_move_fn+0xb1/0x100 __pagevec_lru_add+0x1c/0x30 lru_add_drain_cpu+0xa3/0x130 lru_add_drain+0x2f/0x40 ... The natural solution might be to use a memcg callback whenever memory is hotadded; but that solution has not been scoped out, and it happens that we do have an easy location at which to update lruvec->zone. The lruvec pointer is discovered either by mem_cgroup_zone_lruvec() or by mem_cgroup_page_lruvec(), and both of those do know the right zone. So check and set lruvec->zone in those; and remove the inadequate attempt to set lruvec->zone from lruvec_init(), which is called before NODE_DATA(node) has been allocated in such cases. Ah, there was one exceptionr. For no particularly good reason, mem_cgroup_force_empty_list() has its own code for deciding lruvec. Change it to use the standard mem_cgroup_zone_lruvec() and mem_cgroup_get_lru_size() too. In fact it was already safe against such an oops (the lru lists in danger could only be empty), but we're better proofed against future changes this way. I've marked this for stable (3.6) since we introduced the problem in 3.5 (now closed to stable); but I have no idea if this is the only fix needed to get memory hotadd working with memcg in 3.6, and received no answer when I enquired twice before. Reported-by: Tang Chen <tangchen@cn.fujitsu.com> Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
David Rientjes authored
Using a cross-compiler to fix another issue, the following build error occurred for mips defconfig: arch/mips/fw/arc/misc.c: In function 'ArcHalt': arch/mips/fw/arc/misc.c:25:2: error: implicit declaration of function 'local_irq_disable' Fix it up by including irqflags.h. Signed-off-by: David Rientjes <rientjes@google.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Michal Hocko authored
oom_badness() takes a totalpages argument which says how many pages are available and it uses it as a base for the score calculation. The value is calculated by mem_cgroup_get_limit which considers both limit and total_swap_pages (resp. memsw portion of it). This is usually correct but since fe35004f ("mm: avoid swapping out with swappiness==0") we do not swap when swappiness is 0 which means that we cannot really use up all the totalpages pages. This in turn confuses oom score calculation if the memcg limit is much smaller than the available swap because the used memory (capped by the limit) is negligible comparing to totalpages so the resulting score is too small if adj!=0 (typically task with CAP_SYS_ADMIN or non zero oom_score_adj). A wrong process might be selected as result. The problem can be worked around by checking mem_cgroup_swappiness==0 and not considering swap at all in such a case. Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
David Rientjes authored
do_wp_page() sets mmun_called if mmun_start and mmun_end were initialized and, if so, may call mmu_notifier_invalidate_range_end() with these values. This doesn't prevent gcc from emitting a build warning though: mm/memory.c: In function `do_wp_page': mm/memory.c:2530: warning: `mmun_start' may be used uninitialized in this function mm/memory.c:2531: warning: `mmun_end' may be used uninitialized in this function It's much easier to initialize the variables to impossible values and do a simple comparison to determine if they were initialized to remove the bool entirely. Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Michel Lespinasse authored
Iterating over the vma->anon_vma_chain without anon_vma_lock may cause NULL ptr deref in anon_vma_interval_tree_verify(), because the node in the chain might have been removed. BUG: unable to handle kernel paging request at fffffffffffffff0 IP: [<ffffffff8122c29c>] anon_vma_interval_tree_verify+0xc/0xa0 PGD 4e28067 PUD 4e29067 PMD 0 Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC CPU 0 Pid: 9050, comm: trinity-child64 Tainted: G W 3.7.0-rc2-next-20121025-sasha-00001-g673f98e-dirty #77 RIP: 0010: anon_vma_interval_tree_verify+0xc/0xa0 Process trinity-child64 (pid: 9050, threadinfo ffff880045f80000, task ffff880048eb0000) Call Trace: validate_mm+0x58/0x1e0 vma_adjust+0x635/0x6b0 __split_vma.isra.22+0x161/0x220 split_vma+0x24/0x30 sys_madvise+0x5da/0x7b0 tracesys+0xe1/0xe6 RIP anon_vma_interval_tree_verify+0xc/0xa0 CR2: fffffffffffffff0 Figured out by Bob Liu. Reported-by: Sasha Levin <sasha.levin@oracle.com> Cc: Bob Liu <lliubbo@gmail.com> Signed-off-by: Michel Lespinasse <walken@google.com> Reviewed-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Takashi Iwai authored
The commit [ad756a16: KVM: VMX: Implement PCID/INVPCID for guests with EPT] introduced the unconditional access to SECONDARY_VM_EXEC_CONTROL, and this triggers kernel warnings like below on old CPUs: vmwrite error: reg 401e value a0568000 (err 12) Pid: 13649, comm: qemu-kvm Not tainted 3.7.0-rc4-test2+ #154 Call Trace: [<ffffffffa0558d86>] vmwrite_error+0x27/0x29 [kvm_intel] [<ffffffffa054e8cb>] vmcs_writel+0x1b/0x20 [kvm_intel] [<ffffffffa054f114>] vmx_cpuid_update+0x74/0x170 [kvm_intel] [<ffffffffa03629b6>] kvm_vcpu_ioctl_set_cpuid2+0x76/0x90 [kvm] [<ffffffffa0341c67>] kvm_arch_vcpu_ioctl+0xc37/0xed0 [kvm] [<ffffffff81143f7c>] ? __vunmap+0x9c/0x110 [<ffffffffa0551489>] ? vmx_vcpu_load+0x39/0x1a0 [kvm_intel] [<ffffffffa0340ee2>] ? kvm_arch_vcpu_load+0x52/0x1a0 [kvm] [<ffffffffa032dcd4>] ? vcpu_load+0x74/0xd0 [kvm] [<ffffffffa032deb0>] kvm_vcpu_ioctl+0x110/0x5e0 [kvm] [<ffffffffa032e93d>] ? kvm_dev_ioctl+0x4d/0x4a0 [kvm] [<ffffffff8117dc6f>] do_vfs_ioctl+0x8f/0x530 [<ffffffff81139d76>] ? remove_vma+0x56/0x60 [<ffffffff8113b708>] ? do_munmap+0x328/0x400 [<ffffffff81187c8c>] ? fget_light+0x4c/0x100 [<ffffffff8117e1a1>] sys_ioctl+0x91/0xb0 [<ffffffff815a942d>] system_call_fastpath+0x1a/0x1f This patch adds a check for the availability of secondary exec control to avoid these warnings. Cc: <stable@vger.kernel.org> [v3.6+] Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking updates from David Miller: 1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue lock, from Arik Nemtsov. 2) Don't call 802.11 driver's filter configure method until it's actually open, from Felix Fietkau. 3) Use ieee80211_free_txskb otherwise we leak control information. From Johannes Berg. 4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg. 5) The shift mask trick doesn't work properly when 'optname' is out of range in do_ip_setsockopt(). Use a straightforward switch statement instead, the compiler emits essentially the same code but without the missing range check. From Xi Wang. 6) Fix when we call tcp_replace_ts_recent() otherwise we can erroneously accept a too-high tsval. From Eric Dumazet. 7) VXLAN bug fixes, mostly to do with VLAN header length handling, from Alexander Duyck. 8) Missing return value initialization for IPV6_MINHOPCOUNT socket option handling. From Hannes Frederic. 9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers, from Xiaotian Feng. 10) At smsc911x driver init time, we don't know if the chip is in word swap mode or not. However we do need to wait for the control register's ready bit to be set before we program any other part of the chip. Adjust the wait loop to account for this. From Kamlakant Patel. 11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c 12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala. 13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi. 14) TCP metrics hash table kzalloc() based allocation can fail, back down to using vmalloc() if it does. From Eric Dumazet. 15) Fix packet steering out-of-order delivery regression, from Tom Herbert. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits) net-rps: Fix brokeness causing OOO packets tcp: handle tcp_net_metrics_init() order-5 memory allocation failures batman-adv: process broadcast packets in BLA earlier batman-adv: don't add TEMP clients belonging to other backbone nodes batman-adv: correctly pass the client flag on tt_response batman-adv: fix tt_global_entries flags update tilegx: request_irq with a non-null device name net: correct check in dev_addr_del() tcp: fix retransmission in repair mode sctp: fix /proc/net/sctp/ memory leak Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free" net/smsc911x: Fix ready check in cases where WORD_SWAP is needed drivers/net: fix tasklet misuse issue ipv4/ip_vti.c: VTI fix post-decryption forwarding brcmfmac: fix typo in CONFIG_BRCMISCAN vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN vxlan: fix a typo. ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value doc/net: Fix typo in netdev-features.txt vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large ...
-