The field 'vid' in RITR is reserved when unified bridge model is used
and the RIF's type is sub-port RIF. Instead, ingress VID is configured via
SVFA and egress VID is configured via REIV.

Set 'vid' to zero in RITR register for sub-port RIF when unified bridge
model is used.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via REIV
register.

The table needs to be updated in the following flows:
1. When a RIF is set on a FID, need to iterate over the FID's {Port, VID}
   list and issue REIV write to map the {RIF, Port} to the given VID.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
   need to issue REIV write with a single record to map the {RIF, Port}
   to the given VID.

REIV register supports a simultaneous update of 256 ports, so use this
capability for the first flow.

Handle the two above mentioned flows.

Add mlxsw_sp_fid_evid_map() function to handle egress VID classification
for both unicast and multicast. Layer 2 multicast configuration is already
done in the driver, just move it to the new function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before layer 2 forwarding, the device classifies an incoming packet to
a FID. The classification is done based on one of the following keys:

1. FID
2. VNI (after decapsulation)
3. VID / {Port, VID}

After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that
needs to be routed will ingress the router block.

In the legacy model, when a RIF was created / destroyed, it was
firmware's responsibility to update it in the previously mentioned FID
classification records. In the unified bridge model, this responsibility
moved to software.

The third classification requires to iterate over the FID's {Port, VID}
list and issue SVFA write with the correct mapping table according to the
port's mode (virtual or not). We never map multiple VLANs to the same FID
using VID->FID mapping, so such a mapping needs to be performed once.

When a new FID classification entry is configured and the FID already has
a RIF, set the RIF as part of SVFA configuration.

The reverse needs to be done when clearing a RIF from a FID. Currently,
clearing is done by issuing mlxsw_sp_fid_rif_set() with a NULL RIF pointer.
Instead, introduce mlxsw_sp_fid_rif_unset().

Note that mlxsw_sp_fid_rif_set() is called after the RIF is fully
operational, so it conforms to the internal requirement regarding
SVFA.irif_v: "Must not be set for a non-enabled RIF".

Do not set the ingress RIF for rFIDs, as the {Port, VID}->rFID entry is
configured by firmware when legacy model is used, a next patch will
handle this configuration for rFIDs and unified bridge model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the new model, SFMR no longer configures both VNI->FID and FID->VNI
classifications, but only the later. The former needs to be configured via
SVFA.

Add SVFA configuration as part of vni_set() and vni_clear().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using unified bridge model, firmware no longer configures the egress VID
"under the hood" and moves this responsibility to software.

For layer 2, this means that software needs to determine the egress VID
for both unicast (i.e., FDB) and multicast (i.e., MDB and flooding) flows.

Unicast FDB records and unicast LAG FDB records have new fields - "set_vid"
and "vid", set them. For records which point to router port, do not set
these fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hasdata does not need to be initialized to zero. It will be assigned a
value in the following judgment conditions.
Signed-off-by: Li kunyu <kunyu@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-5.20-20220703' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2022-07-03

this is a pull request of 15 patches for net-next/master.

The first 2 patches are by Max Staudt and add the can327 serial CAN
driver along with a new line discipline ID.

The next patch is by me an fixes a typo in the ctucanfd driver.

The last 12 patches are by Dario Binacchi and integrate slcan CAN
serial driver better into the existing CAN driver API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5-updates-2022-06-29

Chris Mi Says:
==============
Remove dependency between sriov and eswitch mode

Currently, there are three eswitch modes, none, legacy and
switchdev. None is the default mode. And when disabling sriov,
current eswitch mode will be changed to none. This patchset
removes eswitch mode none and also removes dependency between
sriov and eswitch mode. With this patchset, there are two
behavior changes:

Original behavior
-----------------
 - When driver is loaded without sriov enabled, none is the default
   mode. But actually eswitch mode should be either legacy or
   switchdev, so devlink will return unsupported when showing
   eswitch mode.
 - When disabling sriov in either legacy or switchdev mode, eswitch
   mode will be changed to none.

New behavior
------------
 - When driver is loaded, legacy will be the default mode.
 - When disabling sriov in either legacy or switchdev mode, eswitch
   mode will not be changed.

Jianbo Liu Says:
================
Add support offloading police action

This patchset supports offloading police action by flow meter ASO
object in hardware.

The first part is to add interfaces to create and destroy flow meter
ASO object, and modify meter parameters by ACCESS_ASO WQE. As multiple
objects are created at a time, and two meters are in one object,
bitmaps are used manage these meters in one creation.

Then the police action can be mapped to a meter by the action index.
After mlx5e tc action refactoring was merged and post_act table was
added, a simple tc flow with one police action is broken down into two
rules in hardware. One rule with the original match in the original
table, which performs a metadata rewrite and do metering, then jumps
to post_meter table. The second rule is placed in the post_act table
with all the actions left.

The rules in post_meter table match on the meter outcome. If the
outcome is GREEN, we merely jump back to the post_act table for
further processing. Otherwise, the outcome is RED, and we drop the
packet.

The last part is to support flow meter ASO object in sw steering.
Signed-off-by: David S. Miller <davem@davemloft.net>

Dario Binacchi says:
====================
This series originated as a result of CAN communication tests for an
application using the USBtin adapter (https://www.fischl.de/usbtin/).
The tests showed some errors but for the driver everything was ok.
Also, being the first time I used the slcan driver, I was amazed that
it was not possible to configure the bitrate via the ip tool.
For these two reasons, I started looking at the driver code and realized
that it didn't use the CAN network device driver interface.

Starting from these assumptions, I tried to:
- Use the CAN network device driver interface.
- Set the bitrate via the ip tool.
- Send the open/close command to the adapter from the driver.
- Add ethtool support to reset the adapter errors.
- Extend the protocol to forward the adapter CAN communication
  errors and the CAN state changes to the netdev upper layers.

Except for the protocol extension patches (i. e. forward the adapter CAN
communication errors and the CAN state changes to the netdev upper
layers), the whole series has been tested under QEMU with Linux 4.19.208
using the USBtin adapter.
Testing the extension protocol patches requires updating the adapter
firmware. Before modifying the firmware I think it makes sense to know if
these extensions can be considered useful.

Before applying the series I used these commands:

slcan_attach -f -s6 -o /dev/ttyACM0
slcand ttyACM0 can0
ip link set can0 up

After applying the series I am using these commands:

slcan_attach /dev/ttyACM0
slcand ttyACM0 can0
ip link set dev can0 down
ip link set can0 type can bitrate 500000
ethtool --set-priv-flags can0 err-rst-on-open on
ip link set dev can0 up

Now there is a clearer separation between serial line and CAN,
but above all, it is possible to use the ip and ethtool commands
as it happens for any CAN device driver. The changes are backward
compatible, you can continue to use the slcand and slcan_attach
command options.

Changes in v5:
- Update the commit message.
- Restore the use of rtnl_lock() and rtnl_unlock().

Changes in v4:
- Move the patch in front of the patch "[v3,04/13] can: slcan: use CAN network device driver API".
- Add the CAN_BITRATE_UNSET (0) and CAN_BITRATE_UNKNOWN (-1U) macros.
- Simplify the bitrate check to dump it.
- Update the commit description.
- Update the commit description.
- Use the CAN_BITRATE_UNKNOWN macro.
- Use kfree_skb() instead of can_put_echo_skb() in the slc_xmit().
- Remove the `if (slcan_devs)' check in the slc_dealloc().
- Replace `sl->tty == NULL' with `!sl->tty'.
- Use CAN_BITRATE_UNSET (0) and CAN_BITRATE_UNKNOWN (-1U) macros.
- Don't reset the bitrate in ndo_stop() if it has been configured.
- Squashed to the patch [v3,09/13] can: slcan: send the close command to the adapter.
- Use the CAN_BITRATE_UNKNOWN macro.
- Add description of slc_bump_err() function.
- Remove check for the 'e' character at the beggining of the function.
  It was already checked by the caller function.
- Protect decoding against the case the len value is longer than the
  received data.
- Some small changes to make the decoding more readable.
- Increment all the error counters at the end of the function.
- Add description of slc_bump_state() function.
- Remove check for the 's' character at the beggining of the function.
  It was already checked by the caller function.
- Protect decoding against the case the frame len is longer than the
  received data (add SLC_STATE_FRAME_LEN macro).
- Set cf to NULL in case of alloc_can_err_skb() failure.
- Some small changes to make the decoding more readable.
- Use the character 'b' instead of 'f' for bus-off state.

Changes in v3:
- Increment the error counter in case of decoding failure.
- Replace (-1) with (-1U) in the commit description.
- Update the commit description.
- Remove the slc_do_set_bittiming().
- Set the bitrate in the ndo_open().
- Replace -1UL with -1U in setting a fake value for the bitrate.
- Drop the patch "can: slcan: simplify the device de-allocation".
- Add the patch "can: netlink: dump bitrate 0 if can_priv::bittiming.bitrate is -1U".

Changes in v2:
- Put the data into the allocated skb directly instead of first
  filling the "cf" on the stack and then doing a memcpy().
- Move CAN_SLCAN Kconfig option inside CAN_DEV scope.
- Improve the commit message.
- Use the CAN framework support for setting fixed bit rates.
- Improve the commit message.
- Protect decoding against the case the len value is longer than the
  received data.
- Continue error handling even if no skb can be allocated.
- Continue error handling even if no skb can be allocated.
====================

Link: https://lore.kernel.org/all/20220628163137.413025-1-dario.binacchi@amarulasolutions.com/Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

It extends the protocol to receive the adapter CAN state changes
(warning, busoff, etc.) and forward them to the netdev upper levels.

Link: https://lore.kernel.org/all/20220628163137.413025-13-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

It extends the protocol to receive the adapter CAN communication errors
and forward them to the netdev upper levels.

Link: https://lore.kernel.org/all/20220628163137.413025-12-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds a private flag to the slcan driver to switch the
"err-rst-on-open" setting on and off.

"err-rst-on-open" on  - Reset error states on opening command

"err-rst-on-open" off - Don't reset error states on opening command
                        (default)

The setting can only be changed if the interface is down:

    ip link set dev can0 down
    ethtool --set-priv-flags can0 err-rst-on-open {off|on}
    ip link set dev can0 up

Link: https://lore.kernel.org/all/20220628163137.413025-11-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch moves the slcan driver into a separate directory, a later
patch will add more files.

Link: https://lore.kernel.org/all/20220628163137.413025-10-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In case the bitrate has been set via ip tool, this patch changes the
driver to send the open ("O\r") and close ("C\r) commands to the
adapter.

Link: https://lore.kernel.org/all/20220628163137.413025-9-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

It allows to set the bitrate via ip tool, as it happens for the other
CAN device drivers. It still remains possible to set the bitrate via
slcand or slcan_attach utilities. In case the ip tool is used, the
driver will send the serial command to the adapter.

Link: https://lore.kernel.org/all/20220628163137.413025-8-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This is a preparation patch for the upcoming support to change the
bitrate via ip tool, reset the adapter error states via the ethtool API
and, more generally, send commands to the adapter.

Since the close command (i. e. "C\r") will be sent in the ndo_stop()
where netif_running() returns false, a new flag bit (i. e. SLF_XCMD) for
serial transmission has to be added.

Link: https://lore.kernel.org/all/20220628163137.413025-7-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As suggested by commit [1], now the driver uses the functions and the
data structures provided by the CAN network device driver interface.

Currently the driver doesn't implement a way to set bitrate for SLCAN
based devices via ip tool, so you'll have to do this by slcand or
slcan_attach invocation through the -sX parameter:

- slcan_attach -f -s6 -o /dev/ttyACM0
- slcand -f -s8 -o /dev/ttyUSB0

where -s6 in will set adapter's bitrate to 500 Kbit/s and -s8 to
1Mbit/s.
See the table below for further CAN bitrates:
- s0 ->   10 Kbit/s
- s1 ->   20 Kbit/s
- s2 ->   50 Kbit/s
- s3 ->  100 Kbit/s
- s4 ->  125 Kbit/s
- s5 ->  250 Kbit/s
- s6 ->  500 Kbit/s
- s7 ->  800 Kbit/s
- s8 -> 1000 Kbit/s

In doing so, the struct can_priv::bittiming.bitrate of the driver is not
set and since the open_candev() checks that the bitrate has been set, it
must be a non-zero value, the bitrate is set to a fake value (-1U)
before it is called.

Using the rtnl_lock()/rtnl_unlock() functions has become a bit more
tricky as the register_candev() function indirectly calls rtnl_lock()
via register_netdev(). To avoid a deadlock it is therefore necessary to
call rtnl_unlock() before calling register_candev(). The same goes for
the unregister_candev() function.

[1] commit 39549eef ("can: CAN Network device driver and Netlink interface")

Link: https://lore.kernel.org/all/20220628163137.413025-6-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Upcoming changes on slcan driver will require you to specify a bitrate
of value -1 to prevent the open_candev() from failing but at the same
time highlighting that it is a fake value. In this case the command
`ip --details -s -s link show' would print 4294967295 as the bitrate
value. The patch change this value in 0.

Link: https://lore.kernel.org/all/20220628163137.413025-5-dario.binacchi@amarulasolutions.comSuggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

It is used successfully by most (if not all) CAN device drivers. It
allows to remove replicated code.

Link: https://lore.kernel.org/all/20220628163137.413025-4-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Replace printk() calls with corresponding netdev helpers.

Link: https://lore.kernel.org/all/20220628163137.413025-3-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Use the BIT() helper instead of an explicit shift.

Link: https://lore.kernel.org/all/20220628163137.413025-2-dario.binacchi@amarulasolutions.comSigned-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add parsing support by implementing struct mlx5e_tc_act for police
action.

TC rule with police actions is broken down into several rules in
different tables. One rule with the original match in the original
flow table, which set fte_id, do metering, and jump to the post_meter
table. If there are more police actions, more rules are created for
each of them. Besides, a last rule is created in the end.

In post_meter table, there are two pre-defined rules, one is to drop
packet if its packet color is RED, the other is to jump back to
post_act table. As fte_id is updated before jumping, the rule for next
meter is matched to do another round of metering (if there are
multiple meters in the flow rule). Otherwise, last fte_id is matched
and do the original actions.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

As a preparation for validating police action, adds flow_action to
parse state, which is to passed to parsing callbacks.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Flow meter object monitors the packets rate for the flows it is
attached to, and color packets with GREEN or RED. The post meter table
is used to check the color. Packet is dropped if it's RED, or
forwarded to post_act table if GREEN.

Packet color will be set to 8 LSB of the register C5, so they are
reserved for metering, which are previously used for matching fte id.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

There are many definitions to get bits and mask for different types of
metadata register mapping, add generic macros to unify them.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add functions to create and destroy flow meter aso object.
This object only supports the range allocation. 64 objects are
allocated at a time, and there are two meters in each object.
Usually only one meter is allocated for a flow, so bitmap is used
to manage these 128 meters.

TC police action is mapped to hardware meter. As the index is unique
for each police action, add APIs to allocate or free hardware meter by
the index. If the meter is already created, increment its refcnt,
otherwise create new one. If police action has different parameters,
update hardware meter accordingly.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The policing rate and burst from user are converted to flow meter
parameters in hardware. These parameters are set or modified by
ACCESS_ASO WQE, add function to support it.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

If flow meter aso object is supported, set the allocated range, and
initialize aso wqe.

The allocated range is indicated by log_meter_aso_granularity in HW
capabilities, and currently is 6.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add interfaces to use ASO object control channel. The channel consists
of a control SQ and CQ to which user can post ACCESS_ASO work requests
to modify ASO objects. The functions to get wqe from SQ, fill wqe,
post the request, and poll the completion of the work, are provided.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add a separate API to create SQ and CQ for advanced steering
operations (ASO).

Since the mlx5_en API to create these resources is strongly coupled
with netdev channels and datapath elements, this API provides an
alternative for creating send queues that are used for ASO.

Currently the API allows creating channels with 2 wqbbs only - meaning
the support will be for a single ACCESS_ASO wqe with data at a time.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Enable or disable switchdev according to the eswitch mode set by
devlink command. So it is not changed by other functions anymore.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, there are three eswitch modes, none, legacy and switchdev.
None is the default mode. Remove redundant none mode as eswitch mode
should always be either legacy mode or switchdev mode.

With this patch, there are two behavior changes:

1. Legacy becomes the default mode. When querying eswitch mode using
   devlink, a valid mode is always returned.
2. When disabling sriov, the eswitch mode will not change, only vfs
   are unloaded.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Introduce flag to indicate if fdb table is created as a pre-step
to prepare for removing dependency between sriov and eswitch mode
in the downstream patches.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Eswitch vport acl namespace is needed when loading vfs. There is
no need to free and reallocate it when switching eswitch mode.
Introduce flag to indicate if it is created or not. When needed,
create it. Only free it when the driver is unloaded or in bare
metal mode.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Smatch complains about this function:

    drivers/net/ethernet/mellanox/mlx5/core/eswitch.c:2000 mlx5_esw_unlock()
    warn: inconsistent returns '&esw->mode_lock'.

Before commit ec2fa47d ("net/mlx5: Lag, use lag lock") there
used to be a matching mlx5_esw_lock() function and the lock and
unlock functions were symmetric.  But now we take the lock
unconditionally and must unlock unconditionally as well.

As near as I can tell this is dead code and can just be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

ipsec_fs.h is not used and can be safely deleted.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Arun Ramadoss says:

====================
net: dsa: microchip: DSA Driver support for LAN937x

LAN937x is a Multi-Port 100BASE-T1 Ethernet Physical Layer switch
compliant with the IEEE 802.3bw-2015 specification. The device provides
100 Mbit/s transmit and receive capability over a single Unshielded
Twisted Pair (UTP) cable. LAN937x is successive revision of KSZ series
switch.
This series of patches provide the DSA driver support for
Microchip LAN937X switch through MII/RMII interface. The RGMII interface
support will be added in the follow up series.  LAN937x uses the most of
functionality of KSZ9477.

The LAN937x switch series family consists of following SKUs:

LAN9370:
  - 4 T1 Phys
  - 1 RGMII port

LAN9371:
  - 3 T1 Phys & 1 TX Phy
  - 2 RGMII ports

LAN9372:
  - 5 T1 Phys & 1 TX Phy
  - 2 RGMII ports

LAN9373:
  - 5 T1 Phys
  - 2 RGMII
  - 1 SGMII port

LAN9374:
  - 6 T1 Phys
  - 2 RGMII ports

Changes in v15:
- fixed compilation issue.
- Updated the phylink_mac_link_up to check only for 10/100/1000 speed.

Changes in v14:
- Updated the patch series to latest ksz code refactoring.
- RGMII register configuration is removed from the series. It will be added in
the follow up patch series.

Changes in v13:
- Fixed the compilation issue in patch 5 and 6

Changes in v12:
- Removed the reduntant spi indirect enable in lan937x_init
- Used the ksz_port_stp_state_set function
- Apply rgmii internal delay only if it is rgmii port
- Set the bit for 100baseTx in phylink_get_caps
- Moved the ethtool related API from patch 5 to 7
- Moved lan_alu_entry struct in lan937x_dev.h from patch 5 to 9
- Moved lan_vlan_entry in lan937x_dev.h from patch 5 to 10
- Used the ksz_get_stats64 function for get_stats64 hook
- Splitted the patch 5. one for port configuration, spi driver, phy read &
  write and mtu configuration.
- Updated the indentation in ethernet-controller.yaml
- lan937x.yaml: Removed the blank lines, updated the ethernet handle to macb0.
  Added the rgmii internal delay only for the ports.

Changes in v11:
- Tagged as RFC to get the feedback for the subpatches 1/10, 5/10 and 6/10

Changes in v10:
- dsa.yaml: dropped moving mdio properties to dsa.yaml as per the feedback
https://patchwork.kernel.org/project/netdevbpf/patch/20220318085540.281721-3-prasanna.vengateshan@microchip.com/#24787466
- microchip,lan937x.yaml: Naming convention changes in the example
- lan937x_main.c: Moving configurations from lan937x_reset_switch() to setup()
- lan937x_main.c: helper function has been introduced for
  lan937x_internal_phy_read & write
- lan937x_dev.h: lan_alu_struct struct data type changes
- lan937x_main.c: lan937x_get_stats64 make non blocking
- lan937x_main.c: modified lan937x_port_mirror_add to include extack

Changes in v9:
- lan937x_main.c: of_node_put() correction in lan937x_parse_dt_rgmii_delay
- lan937x_dev.c: removed the interface checks from lan937x_apply_rgmii_delay.
- changes in ethernet-controller.yaml and dsa.yaml

Changes in v8:
- lan937x_dev.c: fixed lan937x_r_mib_pkt warning in the sub patches
- lan937x_main.c: phylink_autoneg_inband() check removed in
  lan937x_phylink_mac_link_up()
- lan937x_main.c: made legacy_pre_march2020 = false as this is non-legacy driver
  and indentation correction in lan937x_phylink_mac_link_up()
- removed unnecessary parenthesis in lan937x_get_strings()

Changes in v7:
- microchip,lan937x.yaml: *-internal-delay-ps enum values & commit messages
  corrections
- lan937x_main.c: removed phylink_validate() and added phylink_get_caps()
- lan937x_main.c: added support for ethtool standard stats   (get_eth_*_stats
  and get_stats64)
- lan937x_main.c: removed unnecessary PVID read from lan937x_port_vlan_del()
- integrated the changes of ksz9477 multi bridging support to lan937x dev and
  tested both multi bridging and STP
- lan937x_port_vlan_del - dummy pvid read removed

Changes in v6:
- microchip_t1.c: There was new merge done in the net-next tree for
  microchip_1.c after the v5 submission. Hence rebased it for v6.

Changes in v5:
- microchip,lan937x.yaml: Added mdio properties detail
- microchip,lan937x.yaml: *-internal-delay-ps added under port node
- lan937x_dev.c: changed devm_mdiobus_alloc from of_mdiobus_register as suggested
  by Vladimir
- lan937x_dev.c: added dev_info for rgmii internal delay & error message to user
  in case of out of range values
- lan937x_dev.c: return -EOPNOTSUPP for C45 regnum values for
  lan937x_sw_mdio_read & write operations
- return from function with out storing in a variable
- lan937x_main.c: Added vlan_enable info in vlan_filtering API
- lan937x_main.c: lan937x_port_vlan_del: removed unintended PVID write

Changes in v4:
- tag_ksz.c: cpu_to_be16 to  put_unaligned_be16
- correct spacing in comments
- tag_ksz.c: NETIF_F_HW_CSUM fix is integrated
- lan937x_dev.c: mdio_np is removed from global and handled locally
- lan937x_dev.c: unused functions removed lan937x_cfg32 & lan937x_port_cfg32
- lan937x_dev.c: lan937x_is_internal_100BTX_phy_port function name changes
- lan937x_dev.c: RGMII internal delay handling for MAC. Delay values are
  retrieved from DTS and updated
- lan937x_dev.c: corrected mutex operations for few dev variables
- microchip,lan937x.yaml: introduced rx-internal-delay-ps &
  tx-internal-delay-ps for RGMII internal delay
- lan937x_dev.c: Unnecessary mutex_lock has been removed
- lan937x_main.c: PHY_INTERFACE_MODE_NA handling for lan937x_phylink_validate
- lan937x_main.c: PORT_MIRROR_SNIFFER check in right place
- lan937x_main.c: memset is used instead of writing 0's individually in
  lan937x_port_fdb_add function
- lan937x_main.c: Removed \n from NL_SET_ERR_MSG_MOD calls

Changes in v3:
- Removed settings of cnt_ptr to zero and the memset()
  added a cleanup patch which moves this into ksz_init_mib_timer().
- Used ret everywhere instead of rc
- microchip,lan937x.yaml: Remove mdio compatible
- microchip_t1.c: Renaming standard phy registers
- tag_ksz.c: LAN937X_TAIL_TAG_OVERRIDE renaming
  LAN937X_TAIL_TAG_BLOCKING_OVERRIDE
- tag_ksz.c: Changed Ingress and Egress naming convention based on
  Host
- tag_ksz.c: converted to skb_mac_header(skb) from
  (is_link_local_ether_addr(hdr->h_dest))
- lan937x_dev.c: Removed BCAST Storm protection settings since we
  have Tc commands for them
- lan937x_dev.c: Flow control setting in lan937x_port_setup function
- lan937x_dev.c: RGMII internal delay added only for cpu port,
- lan937x_dev.c: of_get_compatible_child(node,
  "microchip,lan937x-mdio") to of_get_child_by_name(node, "mdio");
- lan937x_dev.c:lan937x_get_interface API: returned
  PHY_INTERFACE_MODE_INTERNAL instead of PHY_INTERFACE_MODE_NA
- lan937x_main.c: Removed compat interface implementation in
  lan937x_config_cpu_port() API & dev_info corrected as well
- lan937x_main.c: deleted ds->configure_vlan_while_not_filtering
  = true
- lan937x_main.c: Added explanation for lan937x_setup lines
- lan937x_main.c: FR_MAX_SIZE correction in lan937x_get_max_mtu API
- lan937x_main.c: removed lan937x_port_bridge_flags dummy functions
- lan937x_spi.c - mdiobus_unregister to be added to spi_remove
  function
- lan937x_main.c: phy link layer changes
- lan937x_main.c: port mirroring: sniff port selection limiting to
  one port
- lan937x_main.c: Changed to global vlan filtering
- lan937x_main.c: vlan_table array to structure
- lan937x_main.c -Use extack instead of reporting errors to Console
- lan937x_main.c - Remove cpu_port addition in vlan_add api
- lan937x_main.c - removed pvid resetting

Changes in v2:
- return check for register read/writes
- dt compatible compatible check is added against chip id value
- lan937x_internal_t1_tx_phy_write() is renamed to
  lan937x_internal_phy_write()
- lan937x_is_internal_tx_phy_port is renamed to
  lan937x_is_internal_100BTX_phy_port as it is 100Base-Tx phy
- Return value for lan937x_internal_phy_write() is -EOPNOTSUPP
  in case of failures
- Return value for lan937x_internal_phy_read() is 0xffff
  for non existent phy
- cpu_port checking is removed from lan937x_port_stp_state_set()
- lan937x_phy_link_validate: 100baseT_Full to 100baseT1_Full
- T1 Phy driver is moved to drivers/net/phy/microchip_t1.c
- Tx phy driver support will be added later
- Legacy switch checkings in dts file are removed.
- tag_ksz.c: Re-used ksz9477_rcv for lan937x_rcv
- tag_ksz.c: Xmit() & rcv() Comments are corrected w.r.to host
- net/dsa/Kconfig: Family skew numbers altered in ascending order
- microchip,lan937x.yaml: eth is replaced with ethernet
- microchip,lan937x.yaml: spi1 is replaced with spi
- microchip,lan937x.yaml: cpu labelling is removed
- microchip,lan937x.yaml: port@x value will match the reg value now
====================

This patch add the LAN937x part support in the existing ksz_spi_probe.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>