- 16 Jan, 2019 40 commits
-
-
Greg Edwards authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 4542d623 upstream. Commands with protection information included were not truncating the protection iov_iter to the number of protection bytes in the command. This resulted in vhost_scsi mis-calculating the size of the protection SGL in vhost_scsi_calc_sgls(), and including both the protection and data SG entries in the protection SGL. Fixes: 09b13fa8 ("vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq") Signed-off-by:
Greg Edwards <gedwards@ddn.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Fixes: 09b13fa8 Cc: stable@vger.kernel.org Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Juerg Haefliger <juergh@canonical.com> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com>
-
Mikulas Patocka authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit c09bcc91 upstream. Reading the registers without waiting for engine idle returns unpredictable values. These unpredictable values result in display corruption - if atyfb_imageblit reads the content of DP_PIX_WIDTH with the bit DP_HOST_TRIPLE_EN set (from previous invocation), the driver would never ever clear the bit, resulting in display corruption. We don't want to wait for idle because it would degrade performance, so this patch modifies the driver so that it never reads accelerator registers. HOST_CNTL doesn't have to be read, we can just write it with HOST_BYTE_ALIGN because no other part of the driver cares if HOST_BYTE_ALIGN is set. DP_PIX_WIDTH is written in the functions atyfb_copyarea and atyfb_fillrect with the default value and in atyfb_imageblit with the value set according to the source image data. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Reviewed-by:
Ville Syrjälä <syrjala@sci.fi> Cc: stable@vger.kernel.org Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Mikulas Patocka authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 3c6c6a78 upstream. The code for manual bit triple is not endian-clean. It builds the variable "hostdword" using byte accesses, therefore we must read the variable with "le32_to_cpu". The patch also enables (hardware or software) bit triple only if the image is monochrome (image->depth). If we want to blit full-color image, we shouldn't use the triple code. Signed-off-by:
-
Ilya Dryomov authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 94e6992b upstream. If the read is large enough, we end up spinning in the messenger: libceph: osd0 192.168.122.1:6801 io error libceph: osd0 192.168.122.1:6801 io error libceph: osd0 192.168.122.1:6801 io error This is a receive side limit, so only reads were affected. Cc: stable@vger.kernel.org Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 8985167e upstream. When driver is built as module and DT node contains clocks compatible (e.g. "samsung,s2mps11-clk"), the module will not be autoloaded because module aliases won't match. The modalias from uevent: of:NclocksT<NULL>Csamsung,s2mps11-clk The modalias from driver: platform:s2mps11-clk The devices are instantiated by parent's MFD. However both Device Tree bindings and parent define the compatible for clocks devices. In case of module matching this DT compatible will be used. The issue will not happen if this is a built-in (no need for module matching) or when clocks DT node does not contain compatible (not correct from bindings perspective but working for driver). Note when backporting to stable kernels: adjust the list of device ID entries. Cc: <stable@vger.kernel.org> Fixes: 53c31b34 ("mfd: sec-core: Add of_compatible strings for clock MFD cells") Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Acked-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Max Filippov authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 40dc948f upstream. The bootloader may pass physical address of the boot parameters structure to the MMUv3 kernel in the register a2. Code in the _SetupMMU block in the arch/xtensa/kernel/head.S is supposed to map that physical address to the virtual address in the configured virtual memory layout. This code haven't been updated when additional 256+256 and 512+512 memory layouts were introduced and it may produce wrong addresses when used with these layouts. Cc: stable@vger.kernel.org Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 0773495b upstream. Xtensa ABI requires stack alignment to be at least 16. In noMMU configuration ARCH_SLAB_MINALIGN is used to align stack. Make it at least 16. This fixes the following runtime error in noMMU configuration, caused by interaction between insufficiently aligned stack and alloca function, that results in corruption of on-stack variable in the libc function glob: Caught unhandled exception in 'sh' (pid = 47, pc = 0x02d05d65) - should not happen EXCCAUSE is 15 Cc: stable@vger.kernel.org Signed-off-by:
-
Max Filippov authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 4119ba21 upstream. This section collects all source .note.* sections together in the vmlinux image. Without it .note.Linux section may be placed at address 0, while the rest of the kernel is at its normal address, resulting in a huge vmlinux.bin image that may not be linked into the xtensa Image.elf. Cc: stable@vger.kernel.org Signed-off-by:
-
Huacai Chen authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 360fe725 ] After commit e509bd7d ("genirq: Allow migration of chained interrupts by installing default action") Loongson-3 fails at here: setup_irq(LOONGSON_HT1_IRQ, &cascade_irqaction); This is because both chained_action and cascade_irqaction don't have IRQF_SHARED flag. This will cause Loongson-3 resume fails because HPET timer interrupt can't be delivered during S3. So we set the irqchip of the chained irq to loongson_irq_chip which doesn't disable the chained irq in CP0.Status. Cc: stable@vger.kernel.org Signed-off-by:
Huacai Chen <chenhc@lemote.com> Signed-off-by:
Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20434/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
-
Huacai Chen authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit d06f8a2f ] Masking/unmasking the CPU UART irq in CP0_Status (and redirecting it to other CPUs) may cause interrupts be lost, especially in multi-package machines (Package-0's UART irq cannot be delivered to others). So make mask_loongson_irq() and unmask_loongson_irq() be no-ops. The original problem (UART IRQ may deliver to any core) is also because of masking/unmasking the CPU UART irq in CP0_Status. So it is safe to remove all of the stuff. Signed-off-by:
-
Kees Cook authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 4dc69c1c ] Using memcpy() from a string that is shorter than the length copied means the destination buffer is being filled with arbitrary data from the kernel rodata segment. Instead, use strncpy() which will fill the trailing bytes with zeros. This was found with the future CONFIG_FORTIFY_SOURCE feature. Cc: Daniel Micay <danielmicay@gmail.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Vincenzo Maffione authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 44c445c3 ] This patch fixes a race condition that can result into the interface being up and carrier on, but with transmits disabled in the hardware. The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which allows e1000_watchdog() interleave with e1000_down(). CPU x CPU y -------------------------------------------------------------------- e1000_down(): netif_carrier_off() e1000_watchdog(): if (carrier == off) { netif_carrier_on(); enable_hw_transmit(); } disable_hw_transmit(); e1000_watchdog(): /* carrier on, do nothing */ Signed-off-by:
Vincenzo Maffione <v.maffione@gmail.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Colin Ian King authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 5983587c ] Currently if the stat type is invalid then data[i] is being set either by dereferencing a null pointer p, or it is reading from an incorrect previous location if we had a valid stat type previously. Fix this by skipping over the read of p on an invalid stat type. Detected by CoverityScan, CID#113385 ("Explicit null dereferenced") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reviewed-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Michal Hocko authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit bb177a73 upstream. syzbot has noticed that a specially crafted library can easily hit VM_BUG_ON in __mm_populate kernel BUG at mm/gup.c:1242! invalid opcode: 0000 [#1] SMP CPU: 2 PID: 9667 Comm: a.out Not tainted 4.18.0-rc3 #644 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017 RIP: 0010:__mm_populate+0x1e2/0x1f0 Code: 55 d0 65 48 33 14 25 28 00 00 00 89 d8 75 21 48 83 c4 20 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 75 18 f1 ff 0f 0b e8 6e 18 f1 ff <0f> 0b 31 db eb c9 e8 93 06 e0 ff 0f 1f 00 55 48 89 e5 53 48 89 fb Call Trace: vm_brk_flags+0xc3/0x100 vm_brk+0x1f/0x30 load_elf_library+0x281/0x2e0 __ia32_sys_uselib+0x170/0x1e0 do_fast_syscall_32+0xca/0x420 entry_SYSENTER_compat+0x70/0x7f The reason is that the length of the new brk is not page aligned when we try to populate the it. There is no reason to bug on that though. do_brk_flags already aligns the length properly so the mapping is expanded as it should. All we need is to tell mm_populate about it. Besides that there is absolutely no reason to to bug_on in the first place. The worst thing that could happen is that the last page wouldn't get populated and that is far from putting system into an inconsistent state. Fix the issue by moving the length sanitization code from do_brk_flags up to vm_brk_flags. The only other caller of do_brk_flags is brk syscall entry and it makes sure to provide the proper length so t here is no need for sanitation and so we can use do_brk_flags without it. Also remove the bogus BUG_ONs. [osalvador@techadventures.net: fix up vm_brk_flags s@request@len@] Link: http://lkml.kernel.org/r/20180706090217.GI32658@dhcp22.suse.czSigned-off-by:
Michal Hocko <mhocko@suse.com> Reported-by:
syzbot <syzbot+5dcb560fe12aa5091c06@syzkaller.appspotmail.com> Tested-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by:
Oscar Salvador <osalvador@suse.de> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Huang, Ying" <ying.huang@intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 4.4: - There is no do_brk_flags() function; update do_brk() - do_brk(), vm_brk() return the address on success - Adjust context] Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Oscar Salvador authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 24962af7 upstream. The current code does not make sure to page align bss before calling vm_brk(), and this can lead to a VM_BUG_ON() in __mm_populate() due to the requested lenght not being correctly aligned. Let us make sure to align it properly. Kees: only applicable to CONFIG_USELIB kernels: 32-bit and configured for libc5. Link: http://lkml.kernel.org/r/20180705145539.9627-1-osalvador@techadventures.netSigned-off-by:
-
Kees Cook authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit ba093a6d upstream. The vm_brk() alignment calculations should refuse to overflow. The ELF loader depending on this, but it has been fixed now. No other unsafe callers have been found. Link: http://lkml.kernel.org/r/1468014494-25291-3-git-send-email-keescook@chromium.orgSigned-off-by:
Hector Marco-Gisbert <hecmargi@upv.es> Cc: Ismael Ripoll Ripoll <iripoll@upv.es> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Chen Gang <gang.chen.5i5j@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by:
-
Kees Cook authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 0036d1f7 upstream. A double-bug exists in the bss calculation code, where an overflow can happen in the "last_bss - elf_bss" calculation, but vm_brk internally aligns the argument, underflowing it, wrapping back around safe. We shouldn't depend on these bugs staying in sync, so this cleans up the bss padding handling to avoid the overflow. This moves the bss padzero() before the last_bss > elf_bss case, since the zero-filling of the ELF_PAGE should have nothing to do with the relationship of last_bss and elf_bss: any trailing portion should be zeroed, and a zero size is already handled by padzero(). Then it handles the math on elf_bss vs last_bss correctly. These need to both be ELF_PAGE aligned to get the comparison correct, since that's the expected granularity of the mappings. Since elf_bss already had alignment-based padding happen in padzero(), the "start" of the new vm_brk() should be moved forward as done in the original code. However, since the "end" of the vm_brk() area will already become PAGE_ALIGNed in vm_brk() then last_bss should get aligned here to avoid hiding it as a side-effect. Additionally makes a cosmetic change to the initial last_bss calculation so it's easier to read in comparison to the load_addr calculation above it (i.e. the only difference is p_filesz vs p_memsz). Link: http://lkml.kernel.org/r/1468014494-25291-2-git-send-email-keescook@chromium.orgSigned-off-by:
-
Michal Hocko authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit ecc2bc8a upstream. load_elf_library doesn't handle vm_brk failure although nothing really indicates it cannot do that because the function is allowed to fail due to vm_mmap failures already. This might be not a problem now but later patch will make vm_brk killable (resp. mmap_sem for write waiting will become killable) and so the failure will be more probable. Signed-off-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Miklos Szeredi authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 4c316f2f upstream. Otherwise fuse_dev_do_write() could come in and finish off the request, and the set_bit(FR_SENT, ...) could trigger the WARN_ON(test_bit(FR_SENT, ...)) in request_end(). Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Reported-by: syzbot+ef054c4d3f64cd7f7cec@syzkaller.appspotmai Fixes: 46c34a34 ("fuse: no fc->lock for pqueue parts") Cc: <stable@vger.kernel.org> # v4.2 Signed-off-by:
-
Miklos Szeredi authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 908a572b upstream. Using waitqueue_active() is racy. Make sure we issue a wake_up() unconditionally after storing into fc->blocked. After that it's okay to optimize with waitqueue_active() since the first wake up provides the necessary barrier for all waiters, not the just the woken one. Signed-off-by:
-
Kirill Tkhai authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit d2d2d4fb upstream. After we found req in request_find() and released the lock, everything may happen with the req in parallel: cpu0 cpu1 fuse_dev_do_write() fuse_dev_do_write() req = request_find(fpq, ...) ... spin_unlock(&fpq->lock) ... ... req = request_find(fpq, oh.unique) ... spin_unlock(&fpq->lock) queue_interrupt(&fc->iq, req); ... ... ... ... ... request_end(fc, req); fuse_put_request(fc, req); ... queue_interrupt(&fc->iq, req); Signed-off-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Kirill Tkhai authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit bc78abbd upstream. We may pick freed req in this way: [cpu0] [cpu1] fuse_dev_do_read() fuse_dev_do_write() list_move_tail(&req->list, ...); ... spin_unlock(&fpq->lock); ... ... request_end(fc, req); ... fuse_put_request(fc, req); if (test_bit(FR_INTERRUPTED, ...)) queue_interrupt(fiq, req); Fix that by keeping req alive until we finish all manipulations. Reported-by: syzbot+4e975615ca01f2277bdd@syzkaller.appspotmail.com Signed-off-by:
-
Himanshu Madhani authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 4c1458df upstream. Fixes: 6246b8a1 ("[SCSI] qla2xxx: Enhancements to support ISP83xx.") Fixes: 1bb39548 ("qla2xxx: Correct iiDMA-update calling conventions.") Cc: <stable@vger.kernel.org> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Dominique Martinet authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 62e39417 ] p9stat_free is more of a cleanup function than a 'free' function as it only frees the content of the struct; there are chances of use-after-free if it is improperly used (e.g. p9stat_free called twice as it used to be possible to) Clearing dangling pointers makes the function idempotent and safer to use. Link: http://lkml.kernel.org/r/1535410108-20650-2-git-send-email-asmadeus@codewreck.orgSigned-off-by:
Dominique Martinet <dominique.martinet@cea.fr> Reported-by: syzbot+d4252148d198410b864f@syzkaller.appspotmail.com Signed-off-by:
-
Dominique Martinet authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit b4dc44b3 ] the 9p client code overwrites our glock.client_id pointing to a static buffer by an allocated string holding the network provided value which we do not care about; free and reset the value as appropriate. This is almost identical to the leak in v9fs_file_getlock() fixed by Al Viro in commit ce85dd58 ("9p: we are leaking glock.client_id in v9fs_file_getlock()"), which was returned as an error by a coverity false positive -- while we are here attempt to make the code slightly more robust to future change of the net/9p/client code and hopefully more clear to coverity that there is no problem. Link: http://lkml.kernel.org/r/1536339057-21974-5-git-send-email-asmadeus@codewreck.orgSigned-off-by:
-
Marco Felsch authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit bd24db04 ] The driver ignored the width alignment which exists due to the UYVY colorspace format. Fix the width alignment and make use of the the provided v4l2 helper function to set the width, height and all alignments in one. Fixes: 963ddc63 ("[media] media: tvp5150: Add cropping support") Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Phil Elwell authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 83444987 ] The SC16IS752 is a dual-channel device. The two channels are largely independent, but the IRQ signals are wired together as an open-drain, active low signal which will be driven low while either of the channels requires attention, which can be for significant periods of time until operations complete and the interrupt can be acknowledged. In that respect it is should be treated as a true level-sensitive IRQ. The kernel, however, needs to be able to exit interrupt context in order to use I2C or SPI to access the device registers (which may involve sleeping). Therefore the interrupt needs to be masked out or paused in some way. The usual way to manage sleeping from within an interrupt handler is to use a threaded interrupt handler - a regular interrupt routine does the minimum amount of work needed to triage the interrupt before waking the interrupt service thread. If the threaded IRQ is marked as IRQF_ONESHOT the kernel will automatically mask out the interrupt until the thread runs to completion. The sc16is7xx driver used to use a threaded IRQ, but a patch switched to using a kthread_worker in order to set realtime priorities on the handler thread and for other optimisations. The end result is non-threaded IRQ that schedules some work then returns IRQ_HANDLED, making the kernel think that all IRQ processing has completed. The work-around to prevent a constant stream of interrupts is to mark the interrupt as edge-sensitive rather than level-sensitive, but interpreting an active-low source as a falling-edge source requires care to prevent a total cessation of interrupts. Whereas an edge-triggering source will generate a new edge for every interrupt condition a level-triggering source will keep the signal at the interrupting level until it no longer requires attention; in other words, the host won't see another edge until all interrupt conditions are cleared. It is therefore vital that the interrupt handler does not exit with an outstanding interrupt condition, otherwise the kernel will not receive another interrupt unless some other operation causes the interrupt state on the device to be cleared. The existing sc16is7xx driver has a very simple interrupt "thread" (kthread_work job) that processes interrupts on each channel in turn until there are no more. If both channels are active and the first channel starts interrupting while the handler for the second channel is running then it will not be detected and an IRQ stall ensues. This could be handled easily if there was a shared IRQ status register, or a convenient way to determine if the IRQ had been deasserted for any length of time, but both appear to be lacking. Avoid this problem (or at least make it much less likely to happen) by reducing the granularity of per-channel interrupt processing to one condition per iteration, only exiting the overall loop when both channels are no longer interrupting. Signed-off-by:
Phil Elwell <phil@raspberrypi.org> Signed-off-by:
-
Joel Stanley authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit ee9d21b3 ] When building with clang crt0's _zimage_start is not marked weak, which breaks the build when linking the kernel image: $ objdump -t arch/powerpc/boot/crt0.o |grep _zimage_start$ 0000000000000058 g .text 0000000000000000 _zimage_start ld: arch/powerpc/boot/wrapper.a(crt0.o): in function '_zimage_start': (.text+0x58): multiple definition of '_zimage_start'; arch/powerpc/boot/pseries-head.o:(.text+0x0): first defined here Clang requires the .weak directive to appear after the symbol is declared. The binutils manual says: This directive sets the weak attribute on the comma separated list of symbol names. If the symbols do not already exist, they will be created. So it appears this is different with clang. The only reference I could see for this was an OpenBSD mailing list post[1]. Changing it to be after the declaration fixes building with Clang, and still works with GCC. $ objdump -t arch/powerpc/boot/crt0.o |grep _zimage_start$ 0000000000000058 w .text 0000000000000000 _zimage_start Reported to clang as https://bugs.llvm.org/show_bug.cgi?id=38921 [1] https://groups.google.com/forum/#!topic/fa.openbsd.tech/PAgKKen2YCYSigned-off-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Dengcheng Zhu authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit dc57aaf9 ] After changing CPU online status, it will not be sent any IPIs such as in __flush_cache_all() on software coherency systems. Do this before disabling local IRQ. Signed-off-by:
Dengcheng Zhu <dzhu@wavecomp.com> Signed-off-by:
-
Nicholas Mc Guire authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit c5d59528 ] altera_hw_filt_init() which calls append_internal() assumes that the node was successfully linked in while in fact it can silently fail. So the call-site needs to set return to -ENOMEM on append_internal() returning NULL and exit through the err path. Fixes: 349bcf02 ("[media] Altera FPGA based CI driver module") Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Tomi Valkeinen authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 538f66ba ] A DMM timeout "timed out waiting for done" has been observed on DRA7 devices. The timeout happens rarely, and only when the system is under heavy load. Debugging showed that the timeout can be made to happen much more frequently by optimizing the DMM driver, so that there's almost no code between writing the last DMM descriptors to RAM, and writing to DMM register which starts the DMM transaction. The current theory is that a wmb() does not properly ensure that the data written to RAM is observable by all the components in the system. This DMM timeout has caused interesting (and rare) bugs as the error handling was not functioning properly (the error handling has been fixed in previous commits): * If a DMM timeout happened when a GEM buffer was being pinned for display on the screen, a timeout error would be shown, but the driver would continue programming DSS HW with broken buffer, leading to SYNCLOST floods and possible crashes. * If a DMM timeout happened when other user (say, video decoder) was pinning a GEM buffer, a timeout would be shown but if the user handled the error properly, no other issues followed. * If a DMM timeout happened when a GEM buffer was being released, the driver does not even notice the error, leading to crashes or hang later. This patch adds wmb() and readl() calls after the last bit is written to RAM, which should ensure that the execution proceeds only after the data is actually in RAM, and thus observable by DMM. The read-back should not be needed. Further study is required to understand if DMM is somehow special case and read-back is ok, or if DRA7's memory barriers do not work correctly. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Daniel Axtens authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit f5e28480 ] When enumerating page size definitions to check hardware support, we construct a constant which is (1U << (def->shift - 10)). However, the array of page size definitions is only initalised for various MMU_PAGE_* constants, so it contains a number of 0-initialised elements with def->shift == 0. This means we end up shifting by a very large number, which gives the following UBSan splat: ================================================================================ UBSAN: Undefined behaviour in /home/dja/dev/linux/linux/arch/powerpc/mm/tlb_nohash.c:506:21 shift exponent 4294967286 is too large for 32-bit type 'unsigned int' CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-rc3-00045-ga604f927b012-dirty #6 Call Trace: [c00000000101bc20] [c000000000a13d54] .dump_stack+0xa8/0xec (unreliable) [c00000000101bcb0] [c0000000004f20a8] .ubsan_epilogue+0x18/0x64 [c00000000101bd30] [c0000000004f2b10] .__ubsan_handle_shift_out_of_bounds+0x110/0x1a4 [c00000000101be20] [c000000000d21760] .early_init_mmu+0x1b4/0x5a0 [c00000000101bf10] [c000000000d1ba28] .early_setup+0x100/0x130 [c00000000101bf90] [c000000000000528] start_here_multiplatform+0x68/0x80 ================================================================================ Fix this by first checking if the element exists (shift != 0) before constructing the constant. Signed-off-by:
Daniel Axtens <dja@axtens.net> Signed-off-by:
-
Miles Chen authored
BugLink: https://bugs.launchpad.net/bugs/1810947 [ Upstream commit 33a1a7be ] The issue is found by a fuzzing test. If tty_find_polling_driver() recevies an incorrect input such as ',,' or '0b', the len becomes 0 and strncmp() always return 0. In this case, a null p->ops->poll_init() is called and it causes a kernel panic. Fix this by checking name length against zero in tty_find_polling_driver(). $echo ,, > /sys/module/kgdboc/parameters/kgdboc [ 20.804451] WARNING: CPU: 1 PID: 104 at drivers/tty/serial/serial_core.c:457 uart_get_baud_rate+0xe8/0x190 [ 20.804917] Modules linked in: [ 20.805317] CPU: 1 PID: 104 Comm: sh Not tainted 4.19.0-rc7ajb #8 [ 20.805469] Hardware name: linux,dummy-virt (DT) [ 20.805732] pstate: 20000005 (nzCv daif -PAN -UAO) [ 20.805895] pc : uart_get_baud_rate+0xe8/0x190 [ 20.806042] lr : uart_get_baud_rate+0xc0/0x190 [ 20.806476] sp : ffffffc06acff940 [ 20.806676] x29: ffffffc06acff940 x28: 0000000000002580 [ 20.806977] x27: 0000000000009600 x26: 0000000000009600 [ 20.807231] x25: ffffffc06acffad0 x24: 00000000ffffeff0 [ 20.807576] x23: 0000000000000001 x22: 0000000000000000 [ 20.807807] x21: 0000000000000001 x20: 0000000000000000 [ 20.808049] x19: ffffffc06acffac8 x18: 0000000000000000 [ 20.808277] x17: 0000000000000000 x16: 0000000000000000 [ 20.808520] x15: ffffffffffffffff x14: ffffffff00000000 [ 20.808757] x13: ffffffffffffffff x12: 0000000000000001 [ 20.809011] x11: 0101010101010101 x10: ffffff880d59ff5f [ 20.809292] x9 : ffffff880d59ff5e x8 : ffffffc06acffaf3 [ 20.809549] x7 : 0000000000000000 x6 : ffffff880d59ff5f [ 20.809803] x5 : 0000000080008001 x4 : 0000000000000003 [ 20.810056] x3 : ffffff900853e6b4 x2 : dfffff9000000000 [ 20.810693] x1 : ffffffc06acffad0 x0 : 0000000000000cb0 [ 20.811005] Call trace: [ 20.811214] uart_get_baud_rate+0xe8/0x190 [ 20.811479] serial8250_do_set_termios+0xe0/0x6f4 [ 20.811719] serial8250_set_termios+0x48/0x54 [ 20.811928] uart_set_options+0x138/0x1bc [ 20.812129] uart_poll_init+0x114/0x16c [ 20.812330] tty_find_polling_driver+0x158/0x200 [ 20.812545] configure_kgdboc+0xbc/0x1bc [ 20.812745] param_set_kgdboc_var+0xb8/0x150 [ 20.812960] param_attr_store+0xbc/0x150 [ 20.813160] module_attr_store+0x40/0x58 [ 20.813364] sysfs_kf_write+0x8c/0xa8 [ 20.813563] kernfs_fop_write+0x154/0x290 [ 20.813764] vfs_write+0xf0/0x278 [ 20.813951] __arm64_sys_write+0x84/0xf4 [ 20.814400] el0_svc_common+0xf4/0x1dc [ 20.814616] el0_svc_handler+0x98/0xbc [ 20.814804] el0_svc+0x8/0xc [ 20.822005] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 20.826913] Mem abort info: [ 20.827103] ESR = 0x84000006 [ 20.827352] Exception class = IABT (current EL), IL = 16 bits [ 20.827655] SET = 0, FnV = 0 [ 20.827855] EA = 0, S1PTW = 0 [ 20.828135] user pgtable: 4k pages, 39-bit VAs, pgdp = (____ptrval____) [ 20.828484] [0000000000000000] pgd=00000000aadee003, pud=00000000aadee003, pmd=0000000000000000 [ 20.829195] Internal error: Oops: 84000006 [#1] SMP [ 20.829564] Modules linked in: [ 20.829890] CPU: 1 PID: 104 Comm: sh Tainted: G W 4.19.0-rc7ajb #8 [ 20.830545] Hardware name: linux,dummy-virt (DT) [ 20.830829] pstate: 60000085 (nZCv daIf -PAN -UAO) [ 20.831174] pc : (null) [ 20.831457] lr : serial8250_do_set_termios+0x358/0x6f4 [ 20.831727] sp : ffffffc06acff9b0 [ 20.831936] x29: ffffffc06acff9b0 x28: ffffff9008d7c000 [ 20.832267] x27: ffffff900969e16f x26: 0000000000000000 [ 20.832589] x25: ffffff900969dfb0 x24: 0000000000000000 [ 20.832906] x23: ffffffc06acffad0 x22: ffffff900969e160 [ 20.833232] x21: 0000000000000000 x20: ffffffc06acffac8 [ 20.833559] x19: ffffff900969df90 x18: 0000000000000000 [ 20.833878] x17: 0000000000000000 x16: 0000000000000000 [ 20.834491] x15: ffffffffffffffff x14: ffffffff00000000 [ 20.834821] x13: ffffffffffffffff x12: 0000000000000001 [ 20.835143] x11: 0101010101010101 x10: ffffff880d59ff5f [ 20.835467] x9 : ffffff880d59ff5e x8 : ffffffc06acffaf3 [ 20.835790] x7 : 0000000000000000 x6 : ffffff880d59ff5f [ 20.836111] x5 : c06419717c314100 x4 : 0000000000000007 [ 20.836419] x3 : 0000000000000000 x2 : 0000000000000000 [ 20.836732] x1 : 0000000000000001 x0 : ffffff900969df90 [ 20.837100] Process sh (pid: 104, stack limit = 0x(____ptrval____)) [ 20.837396] Call trace: [ 20.837566] (null) [ 20.837816] serial8250_set_termios+0x48/0x54 [ 20.838089] uart_set_options+0x138/0x1bc [ 20.838570] uart_poll_init+0x114/0x16c [ 20.838834] tty_find_polling_driver+0x158/0x200 [ 20.839119] configure_kgdboc+0xbc/0x1bc [ 20.839380] param_set_kgdboc_var+0xb8/0x150 [ 20.839658] param_attr_store+0xbc/0x150 [ 20.839920] module_attr_store+0x40/0x58 [ 20.840183] sysfs_kf_write+0x8c/0xa8 [ 20.840183] sysfs_kf_write+0x8c/0xa8 [ 20.840440] kernfs_fop_write+0x154/0x290 [ 20.840702] vfs_write+0xf0/0x278 [ 20.840942] __arm64_sys_write+0x84/0xf4 [ 20.841209] el0_svc_common+0xf4/0x1dc [ 20.841471] el0_svc_handler+0x98/0xbc [ 20.841713] el0_svc+0x8/0xc [ 20.842057] Code: bad PC value [ 20.842764] ---[ end trace a8835d7de79aaadf ]--- [ 20.843134] Kernel panic - not syncing: Fatal exception [ 20.843515] SMP: stopping secondary CPUs [ 20.844289] Kernel Offset: disabled [ 20.844634] CPU features: 0x0,21806002 [ 20.844857] Memory Limit: none [ 20.845172] ---[ end Kernel panic - not syncing: Fatal exception ]--- Signed-off-by:
Miles Chen <miles.chen@mediatek.com> Signed-off-by:
-
Shaohua Li authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 9e753ba9 upstream. Commit d595567d (MD: fix invalid stored role for a disk) broke linear hotadd. Let's only fix the role for disks in raid1/10. Based on Guoqing's original patch. Reported-by:
kernel test robot <rong.a.chen@intel.com> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Guoqing Jiang <gqjiang@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Josef Bacik authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit ad22cf6e upstream. We can't use entry->bytes if our entry is a bitmap entry, we need to use entry->max_extent_size in that case. Fix up all the logic to make this consistent. CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
Josef Bacik <jbacik@fb.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Filipe Manana authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 3527a018 upstream. At inode.c:compress_file_range(), under the "free_pages_out" label, we can end up dereferencing the "pages" pointer when it has a NULL value. This case happens when "start" has a value of 0 and we fail to allocate memory for the "pages" pointer. When that happens we jump to the "cont" label and then enter the "if (start == 0)" branch where we immediately call the cow_file_range_inline() function. If that function returns 0 (success creating an inline extent) or an error (like -ENOMEM for example) we jump to the "free_pages_out" label and then access "pages[i]" leading to a NULL pointer dereference, since "nr_pages" has a value greater than zero at that point. Fix this by setting "nr_pages" to 0 when we fail to allocate memory for the "pages" pointer. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201119 Fixes: 771ed689 ("Btrfs: Optimize compressed writeback and reads") CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Liu Bo <bo.liu@linux.alibaba.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
-
Qu Wenruo authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 9c7b0c2e upstream. [BUG] In the following case, rescan won't zero out the number of qgroup 1/0: $ mkfs.btrfs -fq $DEV $ mount $DEV /mnt $ btrfs quota enable /mnt $ btrfs qgroup create 1/0 /mnt $ btrfs sub create /mnt/sub $ btrfs qgroup assign 0/257 1/0 /mnt $ dd if=/dev/urandom of=/mnt/sub/file bs=1k count=1000 $ btrfs sub snap /mnt/sub /mnt/snap $ btrfs quota rescan -w /mnt $ btrfs qgroup show -pcre /mnt qgroupid rfer excl max_rfer max_excl parent child -------- ---- ---- -------- -------- ------ ----- 0/5 16.00KiB 16.00KiB none none --- --- 0/257 1016.00KiB 16.00KiB none none 1/0 --- 0/258 1016.00KiB 16.00KiB none none --- --- 1/0 1016.00KiB 16.00KiB none none --- 0/257 So far so good, but: $ btrfs qgroup remove 0/257 1/0 /mnt WARNING: quotas may be inconsistent, rescan needed $ btrfs quota rescan -w /mnt $ btrfs qgroup show -pcre /mnt qgoupid rfer excl max_rfer max_excl parent child -------- ---- ---- -------- -------- ------ ----- 0/5 16.00KiB 16.00KiB none none --- --- 0/257 1016.00KiB 16.00KiB none none --- --- 0/258 1016.00KiB 16.00KiB none none --- --- 1/0 1016.00KiB 16.00KiB none none --- --- ^^^^^^^^^^ ^^^^^^^^ not cleared [CAUSE] Before rescan we call qgroup_rescan_zero_tracking() to zero out all qgroups' accounting numbers. However we don't mark all qgroups dirty, but rely on rescan to do so. If we have any high level qgroup without children, it won't be marked dirty during rescan, since we cannot reach that qgroup. This will cause QGROUP_INFO items of childless qgroups never get updated in the quota tree, thus their numbers will stay the same in "btrfs qgroup show" output. [FIX] Just mark all qgroups dirty in qgroup_rescan_zero_tracking(), so even if we have childless qgroups, their QGROUP_INFO items will still get updated during rescan. Reported-by:
Misono Tomohiro <misono.tomohiro@jp.fujitsu.com> CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
Qu Wenruo <wqu@suse.com> Reviewed-by:
-
Filipe Manana authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 0f375eed upstream. In a scenario like the following: mkdir /mnt/A # inode 258 mkdir /mnt/B # inode 259 touch /mnt/B/bar # inode 260 sync mv /mnt/B/bar /mnt/A/bar mv -T /mnt/A /mnt/B fsync /mnt/B/bar <power fail> After replaying the log we end up with file bar having 2 hard links, both with the name 'bar' and one in the directory with inode number 258 and the other in the directory with inode number 259. Also, we end up with the directory inode 259 still existing and with the directory inode 258 still named as 'A', instead of 'B'. In this scenario, file 'bar' should only have one hard link, located at directory inode 258, the directory inode 259 should not exist anymore and the name for directory inode 258 should be 'B'. This incorrect behaviour happens because when attempting to log the old parents of an inode, we skip any parents that no longer exist. Fix this by forcing a full commit if an old parent no longer exists. A test case for fstests follows soon. CC: stable@vger.kernel.org # 4.4+ Signed-off-by:
-
Josef Bacik authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 545e3366 upstream. Allocating new chunks modifies both the extent and chunk tree, which can trigger new chunk allocations. So instead of doing list_for_each_safe, just do while (!list_empty()) so we make sure we don't exit with other pending bg's still on our list. CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Omar Sandoval <osandov@fb.com> Reviewed-by:
Josef Bacik <josef@toxicpanda.com> Reviewed-by:
-
Josef Bacik authored
BugLink: https://bugs.launchpad.net/bugs/1810947 commit 553cceb4 upstream. We need to clear the max_extent_size when we clear bits from a bitmap since it could have been from the range that contains the max_extent_size. CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
-
