Add a new write-only svc attribute to send an eject request to the svc
giving the interface number.

So, doing:
echo 3 > /sys/bus/greybus/devices/1-svc/intf_eject

will force eject the module on interface 3 (module slot 1 on EVT1).
This can take some seconds as the pulse width for module release is
large.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>

Add a new svc operation which will be used to send a request to eject a
given interface.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>

The correct check for if the power supply is ready to receive event is
wrong and it should check for the registered flag.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This moves all of the APBridge request protocol commands that are
currently used to a common .h file for everyone to be able to use them
in the future, where needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Tested-by: Mark Greer <mgreer@animalcreek.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

Provide a new function, gb_hd_output() to send data to the apbridge.
This is useful for the camera and audio drivers that need to do this
type of messaging.

The camera driver is converted to use this new function, the audio
driver can use it when it gets merged later.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Tested-by: Mark Greer <mgreer@animalcreek.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

Individual power supply were being freed and checked using the wrong
pointers and at the wrong place, which would make several issues, like
used after free and so on.
Fix it by freeing all allocated memory after release individual power
supply.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

When fetching string properties, memory was being allocated and leaked
when it was not necessary to do so.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

If something goes wrong at setup time for the supplies, we need to
release all the resources allocated already.

Call the supplies release function which will handle the correct
teardown of the supplies.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

After freeing each individual power_supply, free the top controller, if
not it will leak memory at each module insert/remove.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

If setup fail the release for each supply needs to know the status at
unregister time. So, add the field to the structure, update it at setup
time and use it at release.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

If allocation of memory for each supply fail, we should get out of
release any individual supply.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to release the supplies_lock before returning on errors in
gb_power_supplies_setup().
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add wake_detect support to arche-platform driver which is responsible
for SVC control. This patch also adds code for handshaking between
AP <=> SVC. The sequence is,

1.   AP boots
     To keep compatibility between DB3 and EVT platform, SVC will be
     help in reset and AP driver would release it at appropriate time.
	 wake/detect pin (WD8A) = Low
	 reset (SVC/APB1/APB2) = Asserted (as per polarity)
2.   AP Driver gets inserted
  2.1. AP will deassert reset to SVC (following power on sequence)
  2.2. SVC allows 360 milliseconds to elapse after switch boots to work
       around bug described in ENG-330.
  2.3. AP asserts wake/detect pin (WD8A = HIGH)
3.   SVC detects assertion of wake/detect pin, and sends "wake out" signal to AP
4.   AP receives "wake out" signal, takes AP Bridges through their power
     on reset sequence as defined in the bridge ASIC reference manuals
5.   AP takes USB3613 through its power on reset sequence
6.   AP should enumerates AP Bridges

Note: ISR has been deliberately removed (not merged) as we are still
not sure how it will be used, in runtime usage context. Driver as such
doesn't do anything for runtime assert-n-deassert of reset to SVC/APB's,
it just simply offloads it to user by exporting required gpio's.
The exported gpio's are required for FW flashing from user space.
When it comes to usersace manipulated control sequence, user has to manage.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Now the complete handshaking between AP<=>SVC would be
offloaded to parent driver (arche-platform) who is
responsible for SVC control, so the apb-ctrl driver can
just simply bring APB's out of reset during probe itself.

Along with deasserting reset, this patch renames the local fn
to exclusively use it for reset purpose.

Note that, driver is exporting reset gpio to
user, so user can still flash FW from prompt.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With TIME_SYNC functionality, assignment of wake/detect pin
will change,
  WD_8A => to bring APB's out of reset
  WD_8B => TIME_SYNC operation

So in order to support this, we can no longer keep wake_detect
gpio in apb-ctrl driver. So remove it.
In the subsequent patches, wake_detect support will be added
to parent SVC driver (arche-platform) who is responsible for SVC control.

Note that, this patch also removes ISR related code.
The APB state still is maintained, for future use.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Michael Scott <michael.scott@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This removes few unwanted headers related to irq, interrupt, regulator,
spinlock, etc.

Also arrange the rest in alphabetical order to make it more readable.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

wake_detect_gpio and resetn_gpio are guaranteed to be valid in
apb_ctrl_cleanup() and irq-handler, no need to check for their validity.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Relying on apb_ctrl_cleanup() to do the cleanup for errors that occurred
within apb_ctrl_init_seq() isn't a very clean idea. Handle that
separately within apb_ctrl_init_seq().

This will clean apb_ctrl_cleanup() in later patches.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

If devm_gpio_request() returns an error, we shouldn't try to set the
direction of the same gpio.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use dev_err for errors after which we need to abort the currently
running routine and dev_warn for resource allocation failure, with which
we can continue to work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Since NULL could in theory be a valid regulator we ought to check for
IS_ERR() rather than for NULL. In practice this is unlikely to be an
issue but it's better for neatness.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

And so we don't need to check for it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

There can be no invalid values in the DTS. The actual pin numbers are
assigned by gpiolib when the gpio controller is registered.

And so a simple 'gpio < 0' is enough instead of gpio_is_valid() which
also checks for 'gpio < ARCH_NR_GPIOS'.

This will make the usage of of_get_named_gpio() similar with how it is
done in arche-platform driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Platform data 'apb' is guaranteed to be valid in arche_apb_ctrl_remove()
and so no need to check it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

- s/premits/permits
- Remove blank lines at the end of the file
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Propagate errors returned by of_get_named_gpio() instead of sending
-ENODEV.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

svc_reset_gpio is guaranteed to be valid in arche_platform_cleanup. Drop
the useless check.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The current implementation around of_platform_populate() is not so
great. On error, we first print an error message, followed by a success
message and finally we return an error.

And over that we don't undo what we did initially.

This patch puts the APB back into reset and create a separate error
path to make things clear.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Populating APBs operation can potentially fail and it would be better if
we export the GPIOs towards then end of the routine, so that we don't
need to unexport them on error cases.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

arche_pdata is guaranteed to be valid in arche_platform_remove().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The bootrom protocol issues no dynamic debugging messages when it functions
successfully.  Use dev_dbg() to fix that by issuing kernel logs when firmware
download works.
Signed-off-by: Eli Sennesh <esennesh@leaflabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use the host device and connection name when logging errors as the
version-request helper must not assume that all connection have a
bundle.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The bus code should only match bundle devices for now, and must not
assume all greybus devices are bundles.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add missing bus type to driver structure when registering a greybus
driver.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add greybus driver-data accessors.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add support for the flags field of the stream configure request that was
recently added to the camera protocol and update the debugfs arguments
parsing accordingly. The stream configure response layout is also
updated to the latest protocol specification.
Signed-off-by: Jacopo Mondi <jacopo.mondi@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The link config operation was a hack only designed to fulfill the camera
driver's needs. Now that a standard operation is defined for the same
purpose, implement it and remove the hack.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With addition of handshaking between AP <=> SVC, driver
brings out APB out of reset only on reception of WAKE_MOD
signal from SVC. So remove the deassertion from probe.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch enables handshaking of AP and SVC using wake_detect
gpio (WD_8A and WD_8B).
Note that WAKE_DETECT polarity is active-high, so in order to
enable handshaking between AP <=> SVC, we need to set wake_detect
gpio to low initially, so that driver can send WAKE_DET signal
(active-high) to SVC and then SVC can send back WAKE_MOD signal
(active-low).
And on reception of WAKE_MOD signal, driver would bring respective
APB out of reset.

  WD_8A => APB1
  WD_8B => APB2
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In order to allow user to flash the firmware to,

SVC:
user need to assert the reset first, set sysboot pin and
deassert reset. And then issue a flashing command.

And APB:
User need to assert the reset first, and then issue flashing
command.

So this patch exports the gpio's to user.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>