- 16 Dec, 2014 5 commits
-
-
Alexander Kochetkov authored
commit ccfc8663 upstream. commit 6d9939f6 (i2c: omap: split out [XR]DR and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly Set) get handled. 6d9939f6 code doesn't correspond to workaround provided by errata. According to errata ISR must filter out spurious RDR before data read not after. ISR must read RXSTAT to get number of bytes available to read. Because RDR could be set while there could no data in the receive FIFO. Restored pre 6d9939f6 way of handling errata. Found by code review. Real impact haven't seen. Tested on Beagleboard XM C. Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Fixes: 6d9939f6 i2c: omap: split out [XR]DR and [XR]RDY Tested-by:
Felipe Balbi <balbi@ti.com> Reviewed-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Kochetkov authored
commit 27caca9d upstream. commit 1d7afc95 (i2c: omap: ack IRQ in parts) changed the interrupt handler to complete transfers without clearing XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be fired again. As a result, ISR keep processing transfer after it was already complete (from the driver code point of view). A didn't see real impacts of the 1d7afc95, but it is really bad idea to have ISR running on user data after transfer was complete. It looks, what 1d7afc95 violate TI specs in what how AL and NACK should be handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32). According to specs (if I understood correctly), in case of NACK and AL driver must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and NACK, AL, ARDY, and XDR (Master Transmitter Mode). All that is done down the code under the if condition: if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ... The patch restore pre 1d7afc95 logic of handling NACK and AL interrupts, so no interrupts is fired after ISR informs the rest of driver what transfer complete. Note: instead of removing break under NACK case, we could just replace 'break' with 'continue' and allow NACK transfer to finish using ARDY event. I found that NACK and ARDY bits usually set together. That case confirm TI wiki: http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK In order if someone interested in the event traces for NACK and AL cases, I sent them to mailing list. Tested on Beagleboard XM C. Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Seth Forshee authored
commit 8d609725 upstream. These BUGs can be erroneously triggered by frags which refer to tail pages within a compound page. The data in these pages may overrun the hardware page while still being contained within the compound page, but since compound_order() evaluates to 0 for tail pages the assertion fails. The code already iterates through subsequent pages correctly in this scenario, so the BUGs are unnecessary and can be removed. Fixes: f36c3747 ("xen/netfront: handle compound page fragments on transmit") Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Hugh Dickins authored
commit 2022b4d1 upstream. I've been seeing swapoff hangs in recent testing: it's cycling around trying unsuccessfully to find an mm for some remaining pages of swap. I have been exercising swap and page migration more heavily recently, and now notice a long-standing error in copy_one_pte(): it's trying to add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing so even when it's a migration entry or an hwpoison entry. Which wouldn't matter much, except it adds dst_mm next to src_mm, assuming src_mm is already on the mmlist: which may not be so. Then if pages are later swapped out from dst_mm, swapoff won't be able to find where to replace them. There's already a !non_swap_entry() test for stats: move that up before the swap_duplicate() and the addition to mmlist. Signed-off-by:
Hugh Dickins <hughd@google.com> Cc: Kelley Nielsen <kelleynnn@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Weijie Yang authored
commit fb993fa1 upstream. If a frontswap dup-store failed, it should invalidate the expired page in the backend, or it could trigger some data corruption issue. Such as: 1. use zswap as the frontswap backend with writeback feature 2. store a swap page(version_1) to entry A, success 3. dup-store a newer page(version_2) to the same entry A, fail 4. use __swap_writepage() write version_2 page to swapfile, success 5. zswap do shrink, writeback version_1 page to swapfile 6. version_2 page is overwrited by version_1, data corrupt. This patch fixes this issue by invalidating expired data immediately when meet a dup-store failure. Signed-off-by:
Weijie Yang <weijie.yang@samsung.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Seth Jennings <sjennings@variantweb.net> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Bob Liu <bob.liu@oracle.com> Signed-off-by:
-
- 06 Dec, 2014 35 commits
-
-
Greg Kroah-Hartman authored
-
Sergio Gelato authored
BugLink: http://bugs.launchpad.net/bugs/1348670 Fix regression introduced in pre-3.14 kernels by cherry-picking aa07c713 (NFSD: Call ->set_acl with a NULL ACL structure if no entries). The affected code was removed in 3.14 by commit 4ac7249e (nfsd: use get_acl and ->set_acl). The ->set_acl methods are already able to cope with a NULL argument. Signed-off-by:
Sergio Gelato <Sergio.Gelato@astro.su.se> [bwh: Rewrite the subject] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Moritz Mühlenhoff <muehlenhoff@univention.de> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 36074381 upstream. Instead of the arch specific quirk which we are deprecating and that drivers don't understand. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Maurizio Lombardi authored
commit 01a4cc4d upstream. In some cases, the fcoe_rx_list may contains multiple instances of the same skb (the so called "shared skbs"). the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list, modifies (and destroys) its content and then proceed to the next one. The problem is that if the skb is shared, the remaining instances will be corrupted. The solution is to use skb_share_check() before adding the skb to the fcoe_rx_list. [ 6286.808725] ------------[ cut here ]------------ [ 6286.808729] WARNING: at include/scsi/fc_frame.h:173 bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]() [ 6286.808748] Modules linked in: bnx2x(-) mdio dm_service_time bnx2fc cnic uio fcoe libfcoe 8021q garp stp mrp libfc llc scsi_transport_fc scsi_tgt sg iTCO_wdt iTCO_vendor_support coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel e1000e ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper ptp cryptd hpilo serio_raw hpwdt lpc_ich pps_core ipmi_si pcspkr mfd_core ipmi_msghandler shpchp pcc_cpufreq mperf nfsd auth_rpcgss nfs_acl lockd sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit ata_piix drm_kms_helper ttm drm libata i2c_core hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mdio] [ 6286.808750] CPU: 3 PID: 1304 Comm: bnx2fc_l2_threa Not tainted 3.10.0-121.el7.x86_64 #1 [ 6286.808750] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013 [ 6286.808752] 0000000000000000 000000000b36e715 ffff8800deba1e00 ffffffff815ec0ba [ 6286.808753] ffff8800deba1e38 ffffffff8105dee1 ffffffffa05618c0 ffff8801e4c81888 [ 6286.808754] ffffe8ffff663868 ffff8801f402b180 ffff8801f56bc000 ffff8800deba1e48 [ 6286.808754] Call Trace: [ 6286.808759] [<ffffffff815ec0ba>] dump_stack+0x19/0x1b [ 6286.808762] [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80 [ 6286.808763] [<ffffffff8105e00a>] warn_slowpath_null+0x1a/0x20 [ 6286.808765] [<ffffffffa054f415>] bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc] [ 6286.808767] [<ffffffffa054eff0>] ? bnx2fc_disable+0x90/0x90 [bnx2fc] [ 6286.808769] [<ffffffff81085aef>] kthread+0xcf/0xe0 [ 6286.808770] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140 [ 6286.808772] [<ffffffff815fc76c>] ret_from_fork+0x7c/0xb0 [ 6286.808773] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140 [ 6286.808774] ---[ end trace c6cdb939184ccb4e ]--- Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Acked-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
J. Bruce Fields authored
commit bf7bd3e9 upstream. This fixes a regression from 68a33961 "nfsd4: shut down more of delegation earlier". After that commit, nfs4_set_delegation() failures result in nfs4_put_delegation being called, but nfs4_put_delegation doesn't free the nfs4_file that has already been set by alloc_init_deleg(). This can result in an oops on later unmounting the exported filesystem. Note also delaying the fi_had_conflict check we're able to return a better error (hence give 4.1 clients a better idea why the delegation failed; though note CONFLICT isn't an exact match here, as that's supposed to indicate a current conflict, but all we know here is that there was one recently). Reported-by:
Toralf Förster <toralf.foerster@gmx.de> Tested-by:
J. Bruce Fields <bfields@redhat.com> [tuomasjjrasanen: backported to 3.10 Conflicts fs/nfsd/nfs4state.c: Delegation type flags have been removed from upstream code. In 3.10-series, they still exists and therefore the commit caused few conflicts in function signatures. ] Signed-off-by:
Tuomas Räsänen <tuomasjjrasanen@opinsys.fi> Signed-off-by:
-
Trond Myklebust authored
commit c6c15e1e upstream. The currect code for nfsd41_cb_get_slot() and nfsd4_cb_done() has no locking in order to guarantee atomicity, and so allows for races of the form. Task 1 Task 2 ====== ====== if (test_and_set_bit(0) != 0) { clear_bit(0) rpc_wake_up_next(queue) rpc_sleep_on(queue) return false; } This patch breaks the race condition by adding a retest of the bit after the call to rpc_sleep_on(). Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Stanislaw Gruszka authored
commit cfd9167a upstream. RT2800 and newer hardware require padding between header and payload if header length is not multiple of 4. For historical reasons we also align payload to to 4 bytes boundary, but such alignment is not needed on modern H/W. Patch fixes skb_under_panic problems reported from time to time: https://bugzilla.kernel.org/show_bug.cgi?id=84911 https://bugzilla.kernel.org/show_bug.cgi?id=72471 http://marc.info/?l=linux-wireless&m=139108549530402&w=2 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591 Panic happened because we eat 4 bytes of skb headroom on each (re)transmission when sending frame without the payload and the header length not being multiple of 4 (i.e. QoS header has 26 bytes). On such case because paylad_aling=2 is bigger than header_align=0 we increase header_align by 4 bytes. To prevent that we could change the check to: if (payload_length && payload_align > header_align) header_align += 4; but not aligning payload at all is more effective and alignment is not really needed by H/W (that has been tested on OpenWrt project for few years now). Reported-and-tested-by:
Antti S. Lankila <alankila@bel.fi> Debugged-by:
Henrik Asp <solenskiner@gmail.com> Originally-From: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Thomas Körper authored
commit 5247a589 upstream. ikfree_skb() is Called in can_free_echo_skb(), which might be called from (TX Error) interrupt, which triggers the folloing warning: [ 1153.360705] ------------[ cut here ]------------ [ 1153.360715] WARNING: CPU: 0 PID: 31 at net/core/skbuff.c:563 skb_release_head_state+0xb9/0xd0() [ 1153.360772] Call Trace: [ 1153.360778] [<c167906f>] dump_stack+0x41/0x52 [ 1153.360782] [<c105bb7e>] warn_slowpath_common+0x7e/0xa0 [ 1153.360784] [<c158b909>] ? skb_release_head_state+0xb9/0xd0 [ 1153.360786] [<c158b909>] ? skb_release_head_state+0xb9/0xd0 [ 1153.360788] [<c105bc42>] warn_slowpath_null+0x22/0x30 [ 1153.360791] [<c158b909>] skb_release_head_state+0xb9/0xd0 [ 1153.360793] [<c158be90>] skb_release_all+0x10/0x30 [ 1153.360795] [<c158bf06>] kfree_skb+0x36/0x80 [ 1153.360799] [<f8486938>] ? can_free_echo_skb+0x28/0x40 [can_dev] [ 1153.360802] [<f8486938>] can_free_echo_skb+0x28/0x40 [can_dev] [ 1153.360805] [<f849a12c>] esd_pci402_interrupt+0x34c/0x57a [esd402] [ 1153.360809] [<c10a75b5>] handle_irq_event_percpu+0x35/0x180 [ 1153.360811] [<c10a7623>] ? handle_irq_event_percpu+0xa3/0x180 [ 1153.360813] [<c10a7731>] handle_irq_event+0x31/0x50 [ 1153.360816] [<c10a9c7f>] handle_fasteoi_irq+0x6f/0x120 [ 1153.360818] [<c10a9c10>] ? handle_edge_irq+0x110/0x110 [ 1153.360822] [<c1011b61>] handle_irq+0x71/0x90 [ 1153.360823] <IRQ> [<c168152c>] do_IRQ+0x3c/0xd0 [ 1153.360829] [<c1680b6c>] common_interrupt+0x2c/0x34 [ 1153.360834] [<c107d277>] ? finish_task_switch+0x47/0xf0 [ 1153.360836] [<c167c27b>] __schedule+0x35b/0x7e0 [ 1153.360839] [<c10a5334>] ? console_unlock+0x2c4/0x4d0 [ 1153.360842] [<c13df500>] ? n_tty_receive_buf_common+0x890/0x890 [ 1153.360845] [<c10707b6>] ? process_one_work+0x196/0x370 [ 1153.360847] [<c167c723>] schedule+0x23/0x60 [ 1153.360849] [<c1070de1>] worker_thread+0x161/0x460 [ 1153.360852] [<c1090fcf>] ? __wake_up_locked+0x1f/0x30 [ 1153.360854] [<c1070c80>] ? rescuer_thread+0x2f0/0x2f0 [ 1153.360856] [<c1074f01>] kthread+0xa1/0xc0 [ 1153.360859] [<c1680401>] ret_from_kernel_thread+0x21/0x30 [ 1153.360861] [<c1074e60>] ? kthread_create_on_node+0x110/0x110 [ 1153.360863] ---[ end trace 5ff83639cbb74b35 ]--- This patch replaces the kfree_skb() by dev_kfree_skb_any(). Signed-off-by:
Thomas Körper <thomas.koerper@esd.eu> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Thor Thayer authored
commit 0a8727e6 upstream. An IOCTL call that calls spi_setup() and then dw_spi_setup() will overwrite the persisted last transfer speed. On each transfer, the SPI speed is compared to the last transfer speed to determine if the clock divider registers need to be updated (did the speed change?). This bug was observed with the spidev driver using spi-config to update the max transfer speed. This fix: Don't overwrite the persisted last transaction clock speed when updating the SPI parameters in dw_spi_setup(). On the next transaction, the new speed won't match the persisted last speed and the hardware registers will be updated. On initialization, the persisted last transaction clock speed will be 0 but will be updated after the first SPI transaction. Move zeroed clock divider check into clock change test because chip->clk_div is zero on startup and would cause a divide-by-zero error. The calculation was wrong as well (can't support odd #). Reported-by:
Vlastimil Setka <setka@vsis.cz> Signed-off-by:
Thor Thayer <tthayer@opensource.altera.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Sagi Grimberg authored
commit 3b726ae2 upstream. In this case the cm_id->context is the isert_np, and the cm_id->qp is NULL, so use that to distinct the cases. Since we don't expect any other events on this cm_id we can just return -1 for explicit termination of the cm_id by the cma layer. Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Roland Dreier authored
commit 885e7b0e upstream. If an initiator sends a zero-length command (e.g. TEST UNIT READY) but sets the transfer direction in the transport layer to indicate a data-out phase, we still shouldn't try to transfer data. At best it's a NOP, and depending on the transport, we might crash on an uninitialized sg list. Reported-by:
Craig Watson <craig.watson@vanguard-rugged.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Bart Van Assche authored
commit ab477c1f upstream. It is not guaranteed to that srp_sq_size is supported by the HCA. So if we failed to create the QP with ENOMEM, try with a smaller srp_sq_size. Keep it up until we hit MIN_SRPT_SQ_SIZE, then fail the connection. Reported-by:
Mark Lehrer <lehrer@gmail.com> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit a1f9a407 upstream. The xpad wireless endpoint is not a bulk endpoint on my devices, but rather an interrupt one, so the USB core complains when it is submitted. I'm guessing that the author really did mean that this should be an interrupt urb, but as there are a zillion different xpad devices out there, let's cover out bases and handle both bulk and interrupt endpoints just as easily. Signed-off-by:
"Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Thomas Petazzoni authored
commit 995ab518 upstream. Under extremely rare conditions, in an MPCore node consisting of at least 3 CPUs, two CPUs trying to perform a STREX to data on the same shared cache line can enter a livelock situation. This patch enables the HW mechanism that overcomes the bug. This fixes the incorrect setup of the STREX backoff delay bit due to a wrong description in the specification. Note that enabling the STREX backoff delay mechanism is done by leaving the bit *cleared*, while the bit was currently being set by the proc-v7.S code. [Thomas: adapt to latest mainline, slightly reword the commit log, add stable markers.] Fixes: de490193 ("arm: mm: Add support for PJ4B cpu and init routines") Signed-off-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit ef59a20b upstream. According to the manuals I have, XScale auxiliary register should be reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to also use c1, c0, 1. The issue was primarily noticed thanks to qemu reporing "unsupported instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255 XScale Core manuals and in PXA270 and PXA320 Developers Guides. Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board. Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by:
-
Jurgen Kramer authored
commit 6e84a8d7 upstream. This patch adds a USB control message delay quirk for a few specific Marantz/Denon devices. Without the delay the DACs will not work properly and produces the following type of messages: Nov 15 10:09:21 orwell kernel: [ 91.342880] usb 3-13: clock source 41 is not valid, cannot use Nov 15 10:09:21 orwell kernel: [ 91.343775] usb 3-13: clock source 41 is not valid, cannot use There are likely other Marantz/Denon devices using the same USB module which exhibit the same problems. But as this cannot be verified I limited the patch to the devices I could test. The following two devices are covered by this path: - Marantz SA-14S1 - Marantz HD-DAC1 Signed-off-by:
Jurgen Kramer <gtmkramer@xs4all.nl> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Alexey Khoroshilov authored
commit efbd50d2 upstream. It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds the missing deallocation. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by:
Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by:
-
Mathias Nyman authored
commit c3492dbf upstream. A halted endpoint ring must first be reset, then move the ring dequeue pointer past the problematic TRB. If we start the ring too early after reset, but before moving the dequeue pointer we will end up executing the same problematic TRB again. As we always issue a set transfer dequeue command after a reset endpoint command we can skip starting endpoint rings at reset endpoint command completion. Without this fix we end up trying to handle the same faulty TD for contol endpoints. causing timeout, and failing testusb ctrl_out write tests. Fixes: e9df17eb (USB: xhci: Correct assumptions about number of rings per endpoint.) Tested-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Hans de Goede authored
commit 263e80b4 upstream. This wireless mouse receiver needs a reset-resume quirk to properly come out of reset. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Troy Clark authored
commit 204ec6e0 upstream. Add PIDs for new Matrix Orbital GTT series products. Signed-off-by:
Troy Clark <tclark@matrixorbital.ca> [johan: shorten commit message ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Preston Fick authored
commit ffcfe30e upstream. Signed-off-by:
Preston Fick <pffick@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 5d1678a3 upstream. Fix handling of TTY error flags, which are not bitmasks and must specifically not be ORed together as this prevents the line discipline from recognising them. Also insert null characters when reporting overrun errors as these are not associated with the received character. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 855515a6 upstream. Fix reporting of overrun errors, which are not associated with a character. Instead insert a null character and report only once. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 75bcbf29 upstream. Fix reporting of overrun errors, which should only be reported once using the inserted null character. Fixes: 6b8f1ca5 ("USB: ssu100: set tty_flags in ssu100_process_packet") Signed-off-by:
-
Cristina Ciocan authored
commit ccf54555 upstream. The direction field is set on 7 bits, thus we need to AND it with 0111 111 mask in order to retrieve it, that is 0x7F, not 0xCF as it is now. Fixes: ade7ef7b (staging:iio: Differential channel handling) Signed-off-by:
Cristina Ciocan <cristina.ciocan@intel.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Laurent Dufour authored
commit 3b8a3c01 upstream. On pseries system (LPAR) xmon failed to enter when running in LE mode, system is hunging. Inititating xmon will lead to such an output on the console: SysRq : Entering xmon cpu 0x15: Vector: 0 at [c0000003f39ffb10] pc: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70 lr: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70 sp: c0000003f39ffc70 msr: 8000000000009033 current = 0xc0000003fafa7180 paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01 pid = 14617, comm = bash Bad kernel stack pointer fafb4b0 at eca7cc4 cpu 0x15: Vector: 300 (Data Access) at [c000000007f07d40] pc: 000000000eca7cc4 lr: 000000000eca7c44 sp: fafb4b0 msr: 8000000000001000 dar: 10000000 dsisr: 42000000 current = 0xc0000003fafa7180 paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01 pid = 14617, comm = bash cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop xmon: WARNING: bad recursive fault on cpu 0x15 The root cause is that xmon is calling RTAS to turn off the surveillance when entering xmon, and RTAS is requiring big endian parameters. This patch is byte swapping the RTAS arguments when running in LE mode. Signed-off-by:
Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 415072a0 upstream. Instead of the arch specific quirk which we are deprecating Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 746c9e9f upstream. We have a historical hack that treats missing ranges properties as the equivalent of an empty one. This is needed for ancient PowerMac "bad" device-trees, and shouldn't be enabled for any other PowerPC platform, otherwise we get some nasty layout of devices in sysfs or even duplication when a set of otherwise identically named devices is created multiple times under a different parent node with no ranges property. This fix is needed for the PowerNV i2c busses to be exposed properly and will fix a number of other embedded cases. Signed-off-by:
Grant Likely <grant.likely@linaro.org> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Charles Keepax authored
commit 9da7a5a9 upstream. We should not free any buffers associated with writing out coefficients to the DSP until all the async writes have completed. This patch updates the out of memory path when allocating a new buffer to include a call to regmap_async_complete. Reported-by:
JS Park <aitdark.park@samsung.com> Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Fabio Estevam authored
commit c251ea7b upstream. On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen 5 seconds after the end of a playback. The SMALL_POP bit should fix this, but its definition is incorrect: according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not bit 1. Fix the definition accordingly and enable the bit as intended per the code comment. After applying this change, no loud 'click' sound is heard after playback Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit f144d149 upstream. This can be set by quirks/drivers to be used by the architecture code that assigns the MSI addresses. We additionally add verification in the core MSI code that the values assigned by the architecture do satisfy the limitation in order to fail gracefully if they don't (ie. the arch hasn't been updated to deal with that quirk yet). Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Jiri Bohac authored
[ Upstream commit 01462405 ] This fixes an old regression introduced by commit b0d0d915 (ipx: remove the BKL). When a recvmsg syscall blocks waiting for new data, no data can be sent on the same socket with sendmsg because ipx_recvmsg() sleeps with the socket locked. This breaks mars-nwe (NetWare emulator): - the ncpserv process reads the request using recvmsg - ncpserv forks and spawns nwconn - ncpserv calls a (blocking) recvmsg and waits for new requests - nwconn deadlocks in sendmsg on the same socket Commit b0d0d915 has simply replaced BKL locking with lock_sock/release_sock. Unlike now, BKL got unlocked while sleeping, so a blocking recvmsg did not block a concurrent sendmsg. Only keep the socket locked while actually working with the socket data and release it prior to calling skb_recv_datagram(). Signed-off-by:
Jiri Bohac <jbohac@suse.cz> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Mathias Krause authored
[ Upstream commit a5f6fc28 ] pptp_getname() only partially initializes the stack variable sa, particularly only fills the pptp part of the sa_addr union. The code thereby discloses 16 bytes of kernel stack memory via getsockname(). Fix this by memset(0)'ing the union before. Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by:
Mathias Krause <minipli@googlemail.com> Signed-off-by:
-
Martin Hauke authored
[ Upstream commit bb2bdeb8 ] Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e) Signed-off-by:
Martin Hauke <mardnh@gmx.de> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit 8c2dd544 ] In case of any failure ieee802154fake_probe() just calls unregister_netdev(). But it does not look safe to unregister netdevice before it was registered. The patch implements straightforward resource deallocation in case of failure in ieee802154fake_probe(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
-
