Add xfs_set_inode32() to be used to enable inode32 allocation mode. this
will reduce the amount of duplicated code needed to mount/remount a
filesystem with inode32 option.  This patch also changes
xfs_set_inode64() to return the maximum AG number that inodes can be
allocated instead of set mp->m_maxagi by itself, so that the behaviour
is the same as xfs_set_inode32().  This simplifies code that calls these
functions and needs to know the maximum AG that inodes can be allocated
in.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

since 64-bit inodes can be accessed while using inode32, and these can
also be used on 32-bit kernels, there is no reason to still keep inode32
as the default mount option.  If the filesystem cannot handle 64bit
inode numbers (i.e CONFIG_LBDAF is not enabled and BITS_PER_LONG == 32),
XFS_MOUNT_SMALL_INUMS will still be set by default, so inode64 is not an
unconditional default value.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

xfs_ialloc_next_ag() currently resets m_agirotor when it is equal to
m_maxagi:

         if (++mp->m_agirotor == mp->m_maxagi)
	         mp->m_agirotor = 0;

But, if for some reason mp->m_maxagi changes to a lower value than
current m_agirotor, this condition will never be true, causing
m_agirotor to exceed the maximum allowed value (m_maxagi).

This implies mainly during lookups for xfs_perag structs in its radix
tree, since the agno value used for the lookup is based on m_agirotor.
An out-of-range m_agirotor may cause a lookup failure which in case will
return NULL.

As an example, the value of m_maxagi is decreased during
inode64->inode32 remount process, case where I've found this problem.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Actually, there is no reason about why a user must umount and mount a
XFS filesystem to enable 'inode64' option. So, this patch makes this a
remountable option.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Cancel work of the xfs_sync_worker before teardown of the log in
xfs_unmountfs.  This prevents occasional crashes on unmount like so:

PID: 21602  TASK: ee9df060  CPU: 0   COMMAND: "kworker/0:3"
 #0 [c5377d28] crash_kexec at c0292c94
 #1 [c5377d80] oops_end at c07090c2
 #2 [c5377d98] no_context at c06f614e
 #3 [c5377dbc] __bad_area_nosemaphore at c06f6281
 #4 [c5377df4] bad_area_nosemaphore at c06f629b
 #5 [c5377e00] do_page_fault at c070b0cb
 #6 [c5377e7c] error_code (via page_fault) at c070892c
    EAX: f300c6a8  EBX: f300c6a8  ECX: 000000c0  EDX: 000000c0  EBP: c5377ed0
    DS:  007b      ESI: 00000000  ES:  007b      EDI: 00000001  GS:  ffffad20
    CS:  0060      EIP: c0481ad0  ERR: ffffffff  EFLAGS: 00010246
 #7 [c5377eb0] atomic64_read_cx8 at c0481ad0
 #8 [c5377ebc] xlog_assign_tail_lsn_locked at f7cc7c6e [xfs]
 #9 [c5377ed4] xfs_trans_ail_delete_bulk at f7ccd520 [xfs]
#10 [c5377f0c] xfs_buf_iodone at f7ccb602 [xfs]
#11 [c5377f24] xfs_buf_do_callbacks at f7cca524 [xfs]
#12 [c5377f30] xfs_buf_iodone_callbacks at f7cca5da [xfs]
#13 [c5377f4c] xfs_buf_iodone_work at f7c718d0 [xfs]
#14 [c5377f58] process_one_work at c024ee4c
#15 [c5377f98] worker_thread at c024f43d
#16 [c5377fbc] kthread at c025326b
#17 [c5377fe8] kernel_thread_helper at c070e834

PID: 26653  TASK: e79143b0  CPU: 3   COMMAND: "umount"
 #0 [cde0fda0] __schedule at c0706595
 #1 [cde0fe28] schedule at c0706b89
 #2 [cde0fe30] schedule_timeout at c0705600
 #3 [cde0fe94] __down_common at c0706098
 #4 [cde0fec8] __down at c0706122
 #5 [cde0fed0] down at c025936f
 #6 [cde0fee0] xfs_buf_lock at f7c7131d [xfs]
 #7 [cde0ff00] xfs_freesb at f7cc2236 [xfs]
 #8 [cde0ff10] xfs_fs_put_super at f7c80f21 [xfs]
 #9 [cde0ff1c] generic_shutdown_super at c0333d7a
#10 [cde0ff38] kill_block_super at c0333e0f
#11 [cde0ff48] deactivate_locked_super at c0334218
#12 [cde0ff58] deactivate_super at c033495d
#13 [cde0ff68] mntput_no_expire at c034bc13
#14 [cde0ff7c] sys_umount at c034cc69
#15 [cde0ffa0] sys_oldumount at c034ccd4
#16 [cde0ffb0] system_call at c0707e66

commit 11159a05 added this to xfs_log_unmount and needs to be cleaned up
at a later date.
Signed-off-by: Ben Myers <bpm@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>

xfs_seek_hole() refinement with hole searching from page cache for unwritten extent.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

xfs_seek_data() refinement with unwritten extents check up from page cache.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Introduce helpers to probe data or hole offset from page cache.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

The type is already indicated by the function naming explicitly, so this argument
can be omitted from those calls.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

While xfs_buftarg_shrink() is freeing buffers from the dispose list (filled with
buffers from lru list), there is a possibility to have xfs_buf_stale() racing
with it, and removing buffers from dispose list before xfs_buftarg_shrink() does
it.

This happens because xfs_buftarg_shrink() handle the dispose list without
locking and the test condition in xfs_buf_stale() checks for the buffer being in
*any* list:

if (!list_empty(&bp->b_lru))

If the buffer happens to be on dispose list, this causes the buffer counter of
lru list (btp->bt_lru_nr) to be decremented twice (once in xfs_buftarg_shrink()
and another in xfs_buf_stale()) causing a wrong account usage of the lru list.

This may cause xfs_buftarg_shrink() to return a wrong value to the memory
shrinker shrink_slab(), and such account error may also cause an underflowed
value to be returned; since the counter is lower than the current number of
items in the lru list, a decrement may happen when the counter is 0, causing
an underflow on the counter.

The fix uses a new flag field (and a new buffer flag) to serialize buffer
handling during the shrink process. The new flag field has been designed to use
btp->bt_lru_lock/unlock instead of xfs_buf_lock/unlock mechanism.

dchinner, sandeen, aquini and aris also deserve credits for this.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

If range.start or range.minlen is bigger than filesystem size, return
invalid value error. This fixes possible overflow in BTOBB macro when
passed value was nearly ULLONG_MAX.
Signed-off-by: Tomas Racek <tracek@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Also update some commens in the area to make the code easier to read.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

I noticed that "struct xfs_mount_args" was still declared in
"fs/xfs/xfs_mount.h".  That struct doesn't even exist any more (and
is obviously not referenced elsewhere in that header file).  While
in there, delete four other unneeded struct declarations in that
file.

Doing so highlights that "fs/xfs/xfs_trace.h" was relying indirectly
on "xfs_mount.h" to be #included in order to declare "struct
xfs_bmbt_irec", so add that declaration to resolve that issue.
Signed-off-by: Alex Elder <elder@inktank.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Results in this assert failure in generic/090:

XFS: Assertion failed: *nmap >= 1, file: fs/xfs/xfs_bmap.c, line: 4363
.....
Call Trace:
 [<ffffffff814680db>] xfs_bmapi_read+0x6b/0x370
 [<ffffffff814b64b2>] xfs_rtbuf_get+0x42/0x130
 [<ffffffff814b6f09>] xfs_rtget_summary+0x89/0x120
 [<ffffffff814b7bfe>] xfs_rtallocate_extent_size+0xce/0x340
 [<ffffffff814b89f0>] xfs_rtallocate_extent+0x240/0x290
 [<ffffffff81462c1a>] xfs_bmap_rtalloc+0x1ba/0x340
 [<ffffffff81463a65>] xfs_bmap_alloc+0x35/0x40
 [<ffffffff8146f111>] xfs_bmapi_allocate+0xf1/0x350
 [<ffffffff8146f9de>] xfs_bmapi_write+0x66e/0xa60
 [<ffffffff8144538a>] xfs_iomap_write_direct+0x22a/0x3f0
 [<ffffffff8143707b>] __xfs_get_blocks+0x38b/0x5d0
 [<ffffffff814372d4>] xfs_get_blocks_direct+0x14/0x20
 [<ffffffff811b0081>] do_blockdev_direct_IO+0xf71/0x1eb0
 [<ffffffff811b1015>] __blockdev_direct_IO+0x55/0x60
 [<ffffffff814355ca>] xfs_vm_direct_IO+0x11a/0x1e0
 [<ffffffff8112d617>] generic_file_direct_write+0xd7/0x1b0
 [<ffffffff8143e16c>] xfs_file_dio_aio_write+0x13c/0x320
 [<ffffffff8143e6f2>] xfs_file_aio_write+0x1c2/0x1d0
 [<ffffffff81174a07>] do_sync_write+0xa7/0xe0
 [<ffffffff81175288>] vfs_write+0xa8/0x160
 [<ffffffff81175702>] sys_pwrite64+0x92/0xb0
 [<ffffffff81b68f69>] system_call_fastpath+0x16/0x1b
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1

Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
	SIRFSOC_TIMER_LATCH);

Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized.  Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>

The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work.  Replace it with a fresh
method.  In particular:

 * always attempt to do an atomic open+lookup, both for the create case
   and for lookups of existing files.
 * fix symlink handling by returning 1 to the VFS so that we can follow
   the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>

setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Pull MIPS updates from Ralf Baechle:
 "The lion share of this pull request are fixes for clk-related breakage
  caused by other changes during this merge window.  For some platforms
  the fix was as simple as selecting HAVE_CLK, for others like the
  Loongson 2 significant restructuring was required.

  The remainder are changes required to get the Lantiq code to work
  again."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Loongson 2: Sort out clock managment.
  MIPS: Loongson 1: more clk support and add select HAVE_CLK
  MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: Lantiq: Platform specific CLK fixup
  MIPS: Lantiq: Add device_tree_init function
  MIPS: Lantiq: Fix interface clock and PCI control register offset

Pull UML fixes from Richard Weinberger:
 "This patch set contains mostly fixes and cleanups.  The UML tty driver
  uses now tty_port and is no longer broken like hell  :-)"

* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Add arch/x86/um to MAINTAINERS
  um: pass siginfo to guest process
  um: fix ubd_file_size for read-only files
  um: pull interrupt_end() into userspace()
  um: split syscall_trace(), pass pt_regs to it
  um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
  um: set BLK_CGROUP=y in defconfig
  um: remove count_lock
  um: fully use tty_port
  um: Remove dead code
  um: remove line_ioctl()
  TTY: um/line, use tty from tty_port
  TTY: um/line, add tty_port

Pull ARM DMA engine updates from Russell King:
 "This looks scary at first glance, but what it is is:
   - a rework of the sa11x0 DMA engine driver merged during the previous
     cycle, to extract a common set of helper functions for DMA engine
     implementations.
   - conversion of amba-pl08x.c to use these helper functions.
   - addition of OMAP DMA engine driver (using these helper functions),
     and conversion of some of the OMAP DMA users to use DMA engine.

  Nothing in the helper functions is ARM specific, so I hope that other
  implementations can consolidate some of their code by making use of
  these helpers.

  This has been sitting in linux-next most of the merge cycle, and has
  been tested by several OMAP folk.  I've tested it on sa11x0 platforms,
  and given it my best shot on my broken platforms which have the
  amba-pl08x controller.

  The last point is the addition to feature-removal-schedule.txt, which
  will have a merge conflict.  Between myself and TI, we're planning to
  remove the old TI DMA implementation next year."

Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}

* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
  ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
  ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
  Add feature removal of old OMAP private DMA implementation
  mtd: omap2: remove private DMA API implementation
  mtd: omap2: add DMA engine support
  spi: omap2-mcspi: remove private DMA API implementation
  spi: omap2-mcspi: add DMA engine support
  ARM: omap: remove mmc platform data dma_mask and initialization
  mmc: omap: remove private DMA API implementation
  mmc: omap: add DMA engine support
  mmc: omap_hsmmc: remove private DMA API implementation
  mmc: omap_hsmmc: add DMA engine support
  dmaengine: omap: add support for cyclic DMA
  dmaengine: omap: add support for setting fi
  dmaengine: omap: add support for returning residue in tx_state method
  dmaengine: add OMAP DMA engine driver
  dmaengine: sa11x0-dma: add cyclic DMA support
  dmaengine: sa11x0-dma: fix DMA residue support
  dmaengine: PL08x: ensure all descriptors are freed when channel is released
  dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
  ...

Pull ARM audit/signal updates from Russell King:
 "ARM audit/signal handling updates from Al and Will.  This improves on
  the work Viro did last merge window, and sorts out some of the issues
  found with that work."

* 'audit' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7475/1: sys_trace: allow all syscall arguments to be updated via ptrace
  ARM: 7474/1: get rid of TIF_SYSCALL_RESTARTSYS
  ARM: 7473/1: deal with handlerless restarts without leaving the kernel
  ARM: 7472/1: pull all work_pending logics into C function
  ARM: 7471/1: Revert "7442/1: Revert "remove unused restart trampoline""
  ARM: 7470/1: Revert "7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK""

Pull ARM fixes from Russell King:
 "This fixes various issues found during July"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7479/1: mm: avoid NULL dereference when flushing gate_vma with VIVT caches
  ARM: Fix undefined instruction exception handling
  ARM: 7480/1: only call smp_send_stop() on SMP
  ARM: 7478/1: errata: extend workaround for erratum #720789
  ARM: 7477/1: vfp: Always save VFP state in vfp_pm_suspend on UP
  ARM: 7476/1: vfp: only clear vfp state for current cpu in vfp_pm_suspend
  ARM: 7468/1: ftrace: Trace function entry before updating index
  ARM: 7467/1: mutex: use generic xchg-based implementation for ARMv6+
  ARM: 7466/1: disable interrupt before spinning endlessly
  ARM: 7465/1: Handle >4GB memory sizes in device tree and mem=size@start option

Signed-off-by: Richard Weinberger <richard@nod.at>

UML guest processes now get correct siginfo_t for SIGTRAP, SIGFPE,
SIGILL and SIGBUS. Specifically, si_addr and si_code are now correct
where previously they were si_addr = NULL and si_code = 128.
Signed-off-by: Martin Pärtel <martin.partel@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

Made ubd_file_size not request write access. Fixes use of read-only images.
Signed-off-by: Martin Pärtel <martin.partel@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

Now that DM_RAID supports raid10, it needs to select that code
to ensure it is included.

Cc: Jonathan Brassow <jbrassow@redhat.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>