This patch moves all the romImage related header files into
the mach/ directory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds support for LED9, LED10 and LED11 on
the Solution Engine 7724 board. If CONFIG_PM is enabled
then these LEDs are used to show the hardware sleep
mode used by the processor. Useful to debug cpuidle.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds support for the NAND flash chip
attached to CS4 on the KFR2R09 board. The device is
driven by the platform device driver "onenand-flash".
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds support for the WQVGA LCD display used by
the KFR2R09 board. The LCD module is a TX07D34VM0AAA made
by Hitachi, and this module is made up by a R61517 chip
together with a 240x400 pixel display. The screen is
attached to the SuperH Mobile LCDC using a 18-bit SYS bus.

The register settings used by the SYS panel setup code are
based on an out-of-tree driver which apart from duplicating
all LCDC driver code and writing to non-existing hardware
registers also never was posted for upstream merge.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fix the SuperH Mobile LCDC driver to make use of the full
18-bit DRD field in the LDDRDR register. Without this patch
only 16-bit register access is possible. Needed by 18-bit
SYS panels such as the one used on kfr2r09.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Update the SuperH Mobile LCDC driver to wait for SYS bus to
become idle after reading or writing. This is needed by the
kfr2r09 board, but also fixes potential problems on other
boards making use of the LCDC in a SYS configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Missing endif in the early printk case, fix it up..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

There was no big meaning in the support of SVGA,
but 720p support is necessary for ms7724se board.
So, this patch support 720p instead of SVGA.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch removes the unused MSTPCRn register definitions
from the SuperH Mobile code for sh7722, sh7723 and sh7724.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds hwblk support for the sh7724 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds early printk support for SH770x (tested on SH7709 based hp6xx).
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Adds an archhelp blurb for the romImage target so it is reflected in
'make help'.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch is romImage support for the kfr2r09 board V2.

The partner-jet-setup.txt file is converted into assembly code
which becomes the first code to execute from the reset vector.

The file partner-jet-setup.txt can also be used to setup
the hardware using a JTAG debugger so booting from RAM can
be done without burning the code to flash.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch contains support for the romImage build target V2.

The resulting romImage file should be burned to rom
or flash and could be used as small boot loader.

Board code should keep their setup code in the file
romimage.h located in their mach include directory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This cleans up the irqflags tracing code quite a bit and ties it
in to various missing callsites that caused an imbalance when
CONFIG_PROVE_LOCKING was enabled.

Previously this was catching on:

 987 #ifdef CONFIG_PROVE_LOCKING
 988     DEBUG_LOCKS_WARN_ON(!p->hardirqs_enabled);
 989     DEBUG_LOCKS_WARN_ON(!p->softirqs_enabled);
 990 #endif
 991     retval = -EAGAIN;

with hardirqs being doubly enabled, and subsequently bailing out
with the following call trace:

	Call trace:
	[<88035224>] __lock_acquire+0x616/0x6a6
	[<88015a8c>] do_fork+0xf8/0x2b0
	[<880331ec>] trace_hardirqs_on_caller+0xd4/0x114
	[<88241074>] _spin_unlock_irq+0x20/0x64
	[<88035224>] __lock_acquire+0x616/0x6a6
	[<8800386c>] kernel_thread+0x48/0x70
	[<88024ecc>] ____call_usermodehelper+0x0/0x110
	[<88024ecc>] ____call_usermodehelper+0x0/0x110
	[<88003894>] kernel_thread_helper+0x0/0x14
	[<88024bac>] __call_usermodehelper+0x38/0x70
	[<88025dc0>] worker_thread+0x150/0x274
	[<88035b9c>] lock_release+0x0/0x198
	[<88024b74>] __call_usermodehelper+0x0/0x70
	[<88028cf0>] autoremove_wake_function+0x0/0x30
	[<88028bf2>] kthread+0x3e/0x70
	[<88025c70>] worker_thread+0x0/0x274
	[<8800389c>] kernel_thread_helper+0x8/0x14
	[<88028bb4>] kthread+0x0/0x70
	[<88003894>] kernel_thread_helper+0x0/0x14
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This reverts commit 1d29ebeb.

Bumping up the earlytimer initialization causes IRQs to be enabled too
early, which blows up lockdep:

...
NR_IRQS:256 nr_irqs:256
------------[ cut here ]------------
Badness at kernel/lockdep.c:2128

Pid : 0, Comm:          swapper
CPU : 0                 Not tainted  (2.6.31-rc3-00205-g3ed6e12-dirty #2443)

PC is at trace_hardirqs_on_caller+0x48/0x10c
PR is at trace_hardirqs_on_caller+0x3c/0x10c
...

Revert it back to late_time_init time, which fixes up lockdep.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This fixes up the dev_pm_ops conversion and wires up the callbacks needed
for hibernation.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds a defconfig and a mach-types entry for
the kfr2r09 board.

At this point only a few devices like SCIF, KEYSC and
NOR Flash are supported together with sh7724 devices
such as IIC0, IIC1 and the multimedia blocks exported
via UIO.

Kexec is supported, but booting from flash is not (yet).
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds KEYSC keypad support to the kfr2r09 board.

The keys driven by the sh7724 on-chip KEYSC block are
described as a platform device and platform data for
the sh_keysc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds NOR flash support to the kfr2r09 board.

NOR flash support is added by describing the NOR flash
chip hooked up to CS0 as platform device data for the
physmap-flash MTD driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().

This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().

A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().

This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().

The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.

This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.

It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.

The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Move r8a66597 hardware register definitions from the host
controller header file to the platform data header file.

With this change in place we can easily share register
definitions between the host controller driver and a future
gadget driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix UP compile failure caused by irq_thread_check_affinity

Merge branch 'lockdep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep

* 'lockdep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep:
  lockdep: Fix lockdep annotation for pipe_double_lock()

Since genirq: Delegate irq affinity setting to the irq thread
(591d2fb0) compilation with
CONFIG_SMP=n fails with following error:

/usr/src/linux-2.6/kernel/irq/manage.c:
   In function 'irq_thread_check_affinity':
/usr/src/linux-2.6/kernel/irq/manage.c:475:
   error: 'struct irq_desc' has no member named 'affinity'
make[4]: *** [kernel/irq/manage.o] Error 1

That commit adds a new function irq_thread_check_affinity() which
uses struct irq_desc.affinity which is only available for CONFIG_SMP=y.
Move that function under #ifdef CONFIG_SMP.

[ tglx@brownpaperbag: compile and boot tested on UP and SMP ]
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
LKML-Reference: <20090722222232.2eb3e1c4@neptune.home>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The presumed use of the pipe_double_lock() routine is to lock 2 locks in
a deadlock free way by ordering the locks by their address. However it
fails to keep the specified lock classes in order and explicitly
annotates a deadlock.

Rectify this.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
LKML-Reference: <1248163763.15751.11098.camel@twins>

Merge branch 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf

* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
  perf_counter tools: Give perf top inherit option
  perf_counter tools: Fix vmlinux symbol generation breakage
  perf_counter: Detect debugfs location
  perf_counter: Add tracepoint support to perf list, perf stat
  perf symbol: C++ demangling
  perf: avoid structure size confusion by using a fixed size
  perf_counter: Fix throttle/unthrottle event logging
  perf_counter: Improve perf stat and perf record option parsing
  perf_counter: PERF_SAMPLE_ID and inherited counters
  perf_counter: Plug more stack leaks
  perf: Fix stack data leak
  perf_counter: Remove unused variables
  perf_counter: Make call graph option consistent
  perf_counter: Add perf record option to log addresses
  perf_counter: Log vfork as a fork event
  perf_counter: Synthesize VDSO mmap event
  perf_counter: Make sure we dont leak kernel memory to userspace
  perf_counter tools: Fix index boundary check
  perf_counter: Fix the tracepoint channel to perfcounters
  perf_counter, x86: Extend perf_counter Pentium M support
  ...

Merge branch 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softirq: introduce tasklet_hrtimer infrastructure

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clocksource: Prevent NULL pointer dereference
  timer: Avoid reading uninitialized data

Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Delegate irq affinity setting to the irq thread

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: fix nr_uninterruptible accounting of frozen tasks really
  sched: fix load average accounting vs. cpu hotplug
  sched: Account for vruntime wrapping

* 'tj-block-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
  virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch
  block: sysfs fix mismatched queue_var_{store,show} in 64bit kernel
  ataflop: adjust NULL test
  block: fix failfast merge testing in elv_rq_merge_ok()
  z2ram: Small cleanup for z2ram.c

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  fs/Kconfig: move nilfs2 out