- 07 Sep, 2019 9 commits
-
-
Sakari Ailus authored
Convert the remaining %pf users to %ps to prepare for the removal of the old %pf conversion specifier support. Fixes: 32350664 ("scsi: lpfc: Migrate to %px and %pf in kernel print calls") Link: https://lore.kernel.org/r/20190904160423.3865-1-sakari.ailus@linux.intel.comSigned-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Himanshu Madhani authored
Signed-off-by:
Himanshu Madhani <hmadhani@marvell.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Link: https://lore.kernel.org/r/20190830222402.23688-7-hmadhani@marvell.comSigned-off-by:
-
Quinn Tran authored
On fast cable pull, where driver is unable to detect device has disappeared and came back based on switch info, qla2xxx would not re-login while remote port has already invalidated the session. This causes IO timeout. This patch would relogin to remote device for RSCN affected port. Signed-off-by:
Quinn Tran <qutran@marvell.com> Signed-off-by:
-
Quinn Tran authored
Login session was stucked on cable pull. When FW is in the middle PRLI PENDING + driver is in Initiator mode, driver fails to check back with FW to see if the PRLI has completed. This patch would re-check with FW again to make sure PRLI would complete before pushing forward with relogin. Signed-off-by:
-
Himanshu Madhani authored
HINT_MBX_INT_PENDING is not guaranteed to be cleared by firmware. Remove check that prevent driver load with ISP82XX. Signed-off-by:
-
Quinn Tran authored
Use adapter specific callback to read flash instead of ISP adapter specific. Signed-off-by:
-
Himanshu Madhani authored
This patch updates log message which indicates number of vectors used by the driver instead of displaying failure to get maximum requested vectors. Driver will always request maximum vectors during initialization. In the event driver is not able to get maximum requested vectors, it will adjust the allocated vectors. This is normal and does not imply failure in driver. Signed-off-by:
Lee Duncan <lduncan@suse.com> Link: https://lore.kernel.org/r/20190830222402.23688-2-hmadhani@marvell.comSigned-off-by:
-
Damien Le Moal authored
For commands completing with a resid not aligned on the device logical sector size, also print the command CDB in addition to the current message to help debug hardware generating such incorrect command completion information. Link: https://lore.kernel.org/r/20190828053511.14818-1-damien.lemoal@wdc.comSigned-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
-
Govindarajulu Varadarajan authored
pci_alloc_irq_vectors() returns number of vectors allocated. Fix the check for error condition. Fixes: cca678df ("scsi: fnic: switch to pci_alloc_irq_vectors") Link: https://lore.kernel.org/r/20190827211340.1095-1-gvaradar@cisco.comSigned-off-by:
Govindarajulu Varadarajan <gvaradar@cisco.com> Acked-by:
Satish Kharat <satishkh@cisco.com> Signed-off-by:
-
- 30 Aug, 2019 1 commit
-
-
John Pittman authored
Port speed printing was added by commit d948e638 ("scsi: fnic: Add port speed stat to fnic debug stats"). As currently configured, this will cause the port speed to be printed to syslog every 2 seconds. To prevent log spamming, only print the vnic port speed at driver initialization and if the speed changes. Also clean up a small typo in fnic_trace.c. Fixes: d948e638 ("scsi: fnic: Add port speed stat to fnic debug stats") Signed-off-by:
John Pittman <jpittman@redhat.com> Reviewed-by:
-
- 29 Aug, 2019 30 commits
-
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_unsol_compl: drivers/scsi/bnx2fc/bnx2fc_hwi.c:636:30: warning: variable task set but not used [-Wunused-but-set-variable] drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_ofld_cmpl: drivers/scsi/bnx2fc/bnx2fc_hwi.c:1125:21: warning: variable port set but not used [-Wunused-but-set-variable] drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_init_seq_cleanup_task: drivers/scsi/bnx2fc/bnx2fc_hwi.c:1468:30: warning: variable orig_task set but not used [-Wunused-but-set-variable] Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhengbin <zhengbin13@huawei.com> Acked-by:
Saurav Kashyap <skashyap@marvell.com> Signed-off-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_seq_cleanup: drivers/scsi/bnx2fc/bnx2fc_io.c:932:19: warning: variable lport set but not used [-Wunused-but-set-variable] drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_cleanup: drivers/scsi/bnx2fc/bnx2fc_io.c:1001:19: warning: variable lport set but not used [-Wunused-but-set-variable] drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_process_scsi_cmd_compl: drivers/scsi/bnx2fc/bnx2fc_io.c:1882:20: warning: variable host set but not used [-Wunused-but-set-variable] Reported-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function bnx2fc_rcv: drivers/scsi/bnx2fc/bnx2fc_fcoe.c:431:26: warning: variable fh set but not used [-Wunused-but-set-variable] Reported-by:
-
Saurav Kashyap authored
Update the driver version to 8.42.3.0. Signed-off-by:
-
Saurav Kashyap authored
There is a race b/w fipvlan request and response path: ===== qedf_fcoe_process_vlan_resp:113]:2: VLAN response, vid=0xffd. qedf_initiate_fipvlan_req:165]:2: vlan = 0x6ffd already set. qedf_set_vlan_id:139]:2: Setting vlan_id=0ffd prio=3. ====== The request thread sees that vlan is already set and fails to call ctrl_link_up. Fix: - While setting vlan_id use local variable and before setting vlan_id. - Call fcoe_ctlr_link_up in next iteration of fipvlan request. Signed-off-by:
-
Hannes Reinecke authored
The list of rports might become stale so we should rather traverse the discovery list when trying relogin. Signed-off-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Saurav Kashyap authored
Decrease the LL2 MTU size to 2500. Signed-off-by:
-
Saurav Kashyap authored
Prevent race where we're removing the module and we get link update Signed-off-by:
-
Saurav Kashyap authored
Problem Statement: - Driver has fc_id of 0xcc0200 - Driver gets link down (due to test) and calls fcoe_ctlr_link_down(). - At this point, the fc_id of the initiator port is zeroed out. - Driver gets a link up 14 seconds later. - Driver performs FIP VLAN request, gets a response from the switch. - No change in VLAN is detected. - Driver then notifies libfcoe via fcoe_ctlr_link_up(). - Libfcoe then issues a multicast discovery solicitation as expected. - Cisco FCF responds to that correctly. - Libfcoe at this point starts a 3 sec count-down to allow any other FCFs to be discovered. However, at this point, it has been 20 seconds since the last FKA from the driver (which would have been sent prior to backlink toggle), which causes the CVL to be issued from Cisco CVL from the switch is dropped by the driver as the vx_port identification descriptor is present and has value of 0xcc0200, which does not match the driver's value of 0. Libfcoe completes the 3 sec count down and proceeds to issue FLOGI as per protocol. Switch rejects FLogi request. All subsequent FLOGI requests from libfc are rejected by the switch (possibly because it is now expecting a new solicitation). This situation will continue until the next link toggle. Solution: The Vx_port descriptor in the CVL has three fields: MAC address Fabric ID Port Name Today, the code checks for both #1 and #2 above. In the case where we went through a link down, both these will be zero until FLOGI succeeds. We should change our code to check if any one of these 3 is valid and if so, handle the CVL (basically switching from AND to OR). The port name field is definitely expected to be valid always. Signed-off-by:
-
Saurav Kashyap authored
Log s_id, d_id, type and command to the log message. [mkp: fixed warning] Signed-off-by:
-
Saurav Kashyap authored
The current code doeesn't support 20Gbps speed for current and supported speed. Add support for it. Signed-off-by:
-
Saurav Kashyap authored
Driver was wrongly interpreting the supported cap value returned by qed. Solution: Use QED define macros instead of OS defined for interpreting supporting speeds. Signed-off-by:
-
Saurav Kashyap authored
Add shutdown callback handler. Signed-off-by:
-
Nilesh Javali authored
Update module description. Signed-off-by:
Nilesh Javali <njavali@marvell.com> Signed-off-by:
-
Arun Easi authored
Driver was attempting to print cdb[0], which is not set for resets coming from SCSI ioctls. Check for cmd_len before accessing cmnd. Crash info: [84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null) [84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf] [84790.865204] Call Trace: [84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod] [84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod] [84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod] Signed-off-by:
Arun Easi <aeasi@marvell.com> Signed-off-by:
-
Saurav Kashyap authored
- On some setups fipvlan can be retried for long duration and the connection to switch was not there so it was not getting any reply. - During unload this thread was hanging. Problem Resolution: Check if unload is in progress, then quit from fipvlan thread. Signed-off-by:
-
Saurav Kashyap authored
Print messages during exiting condition to help debugging. Signed-off-by:
-
Don Brace authored
Reviewed-by:
Scott Benesh <scott.benesh@microsemi.com> Reviewed-by:
Gerry Morong <gerry.morong@microsemi.com> Signed-off-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
-
Don Brace authored
Reviewed-by:
Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by:
-
Gilbert Wu authored
Add: PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F 3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808 3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809 Reviewed-by:Gilbert Wu <gilbert.wu@microsemi.com> Signed-off-by:
-
Murthy Bhat authored
Return -EINPROGRESS when a rescan worker is queued. Reviewed-by:
Murthy Bhat <Murthy.Bhat@microsemi.com> Signed-off-by:
-
Gilbert Wu authored
Reviewed-by:
-
Mahesh Rajashekhara authored
When each ld is deleted, a rescan event is triggered in the driver. These can stack up waiting on mutex_lock. Change to mutex_try_lock and schedule a rescan for later. Reviewed-by:
Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Signed-off-by:
-
Gilbert Wu authored
Return identify physical device "Phys_Bay_in_Box" as bay_identifier. Reviewed-by:
-
Murthy Bhat authored
- serial number - model - vendor Reviewed-by:
-
Dave Carroll authored
Reviewed-by:
Dave Carroll <david.carroll@microsemi.com> Signed-off-by:
-
Gilbert Wu authored
Reviewed-by:
-
Gilbert Wu authored
Expose physical devices before logical devices. Reviewed-by:
-
James Smart authored
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair contained a bug: a local variable was set to the queue pair by index. This should have allowed the local variable to be natively used. Instead, the code reused the index relative to the local variable, obtaining a random pointer value that when used eventually faulted the system Convert offending code to use local variable. Fixes: c00f62e6 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair") Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Tested-by:
Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by:
-
James Smart authored
Capturing and downloading dif command data and dif data was done a dozen years ago and no longer being used. Also creates a potential security hole. Remove the debugfs buffer for dif debugging. Signed-off-by:
-
