Some sdio chips of rome QCA6174's regulatory domain code of EEPROM is
empty, then ath_is_world_regd will return false for this case, and
it will lead function __ath_reg_dyn_country not work, thus the regdomain
will not update for NL80211_REGDOM_SET_BY_COUNTRY_IE type, it result
ath10k set the same regdomain/reg_5ghz_ctl/reg_2ghz_ctl to firmware,
then the tx power will not changed with different regdomain's AP. The
regulatory domain code of EEPROM of some QCA6174 PCIE chip is 0x6c, it
means world wide regdomain, for this chip, it does not have the issue.

For empty reulatory domain code chip, set it to world regulatory domain
in functio ath_regd_sanitize, then it will fix the issue.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For max bundle size 32, the bundle mask is not same with 8/16.
Change it to match the max bundle size of htc. Otherwise it
will not match with firmware, for example, when bundle count
is 17, then flags of ath10k_htc_hdr is 0x4, if without this
patch, it will be considered as non-bundled packet because it
does not have mask 0xF0, then trigger error message later:
payload length 56747 exceeds max htc length: 4088.

htc->max_msgs_per_htc_bundle is the min value of
HTC_HOST_MAX_MSG_PER_RX_BUNDLE and
msg->ready_ext.max_msgs_per_htc_bundle of ath10k_htc_wait_target,
it will be sent to firmware later in ath10k_htc_start, then
firmware will use it as the final max rx bundle count, in
WLAN.RMH.4.4.1-00029, msg->ready_ext.max_msgs_per_htc_bundle
is 32, it is same with HTC_HOST_MAX_MSG_PER_RX_BUNDLE, so the
final max rx bundle count will be set to 32 in firmware.

This patch only effect sdio chips.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Fixes: 22477652 ("ath10k: change max RX bundle size from 8 to 32 for sdio")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.

This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.

Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.

call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
  skb_gro_receive ([kernel.kallsyms])
  tcp4_gro_receive ([kernel.kallsyms])
  inet_gro_receive ([kernel.kallsyms])
  dev_gro_receive ([kernel.kallsyms])
  napi_gro_receive ([kernel.kallsyms])
  ieee80211_deliver_skb ([mac80211])
  ieee80211_rx_handlers ([mac80211])
  ieee80211_prepare_and_rx_handle ([mac80211])
  ieee80211_rx_napi ([mac80211])
  ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
  ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
  ath10k_sdio_napi_poll ([ath10k_sdio])
  net_rx_action ([kernel.kallsyms])
  softirqentry_text_start ([kernel.kallsyms])
  do_softirq ([kernel.kallsyms])

call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
 _tcp_ack_snd_check ([kernel.kallsyms])
 tcp_v4_do_rcv ([kernel.kallsyms])
 tcp_v4_rcv ([kernel.kallsyms])
 local_deliver_finish ([kernel.kallsyms])
 ip_local_deliver ([kernel.kallsyms])
 ip_rcv_finish ([kernel.kallsyms])
 ip_rcv ([kernel.kallsyms])
 netif_receive_skb_core ([kernel.kallsyms])
 netif_receive_skb_one_core([kernel.kallsyms])
 netif_receive_skb ([kernel.kallsyms])
 netif_receive_skb_internal ([kernel.kallsyms])
 napi_gro_complete ([kernel.kallsyms])
 napi_gro_flush ([kernel.kallsyms])
 napi_complete_done ([kernel.kallsyms])
 ath10k_sdio_napi_poll ([ath10k_sdio])
 net_rx_action ([kernel.kallsyms])
 __softirqentry_text_start ([kernel.kallsyms])
 do_softirq ([kernel.kallsyms])

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Firmware expects all the required REO destination rings setup
while processing wmi_init command. Not doing this causes connected
stations getting disconnected and not able to connect back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is to prepare REO ring setup before sending wmi_init command.
Firmware expects all the required REO rings to be setup while processing
wmi_init command. But as per the current initialization sequence, REO ring
configurations are done only after wmi_init command is sent.
Also refactoring ath11k_mac_create() into ath11k_mac_alloc() and
ath11k_mac_register() to it mac80211 hw structure available before sending
wmi_init command.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently HTT_PPDU_STATS_TAG_USR_COMPLTN_ACK_BA_STATUS tag of PPDU stats
doesn't have valid success bytes info of management frames.
So skip update peer stats for management packets.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Update tx duration in station info form PPDU stats
so that users can dump tx duration of the station.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Guard interval value which comes from VHT_SIG_A TLV has a mapping
where value 0 corresponds to LGI, 1 and 3 corresponds to SGI.

Value 3 which is SGI(0.4us) in VHT was incorrectly mapped to a GI
of 3.2us(only applicable in HE) resulting in incorrect rx GI stats.
Fixing the mapping.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

remove tail check to avoid last amsdu leak.
recycle skb in ppdu id wrap around case
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Adverise MPDU start spacing as no restriction in ht capabilities,
Since IPQ8074 hw support all sorts of mpdu start spcing. With this
observed minor uplink performance improvement in lower data frame
size case with Veriwave clients.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Set the number of tx and rx chains properly on drv_set_antenna().
This will ensure the related ht/vht/he caps are properly recalculated
based on the tx/rx chains set.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add necessary peer assoc params in WMI debug message
while sending the peer assoc command to firmware
to aid in debugging.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qmi firmware ready event start to initialize the core modules and
the sequence executed with mutex lock. In case of any failure
mutex should be unlocked otherwise it will hang during the recovery.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch will add the support to control the transmit power
for traffic to a station associated with the AP.

Underlying firmware will enforce that the maximum tx power will
be based on the regulatory requirements. If the user given
transmit power is greater than the allowed tx power in the given
channel, then the firmware will use the maximum tx power in the
same channel.

Max and Min tx power values will depends on number of tx chain
masks. The allowed tx power range values are from 6 to 23.

When 0 is sent to the firmware as tx power, it will revert to
the default tx power for the station.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currenly in delba process calling ath11k_peer_rx_tid_delete() updates
reo with desc invalid and add tid queue to the flush list. If station
send data traffic without addba req and before tid flush, hw gives
those packets as invalid desc reo error. Since we are dropping these
invalid desc packets results in traffic stall.

This patch fix this issue by updating the reo queue with bawindow size 1
instead of tid removal in delba process.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Accessing already stored first msdu data after the skb expand trigger
use_after_free, since first msdu got deleted. so do the descriptor copy
operation before the skb expand operation.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WMI_VDEV_SET_WMM_PARAMS commmand expects the txoplimit param in the units of
32 microseconds. convert the txop unit from 32 microseconds to absolute
microseconds leads to the higher burst values which is incorrect. so no need
to convert the txop unit from 32 microseconds to absolute microseconds.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fixes sending the pdev id(0,1,2 for mac0, mac1, mac2)
to FW in wmi cmd pktlog enable/disable.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use pipe_id id instead of ret in for loop.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Copy CE and htc service configs for all pipes.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add missing tracing subsystem define.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

sdio does not support wow, this patch is to enable it. When system enter
sleep state, if wowlan is enabled, then sdio chip will keep power if
platform support keep power, after resume, it will not need to re-load
firmware again.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Change log level from warn to dbg level of mpdu status
of sdio chip.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.

This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For sdio chip, the max credit size in firmware is 1556, the 1556
include payload, ieee80211 header, htt header, htc header. So it
need to set the max mtu to 1500 to forbidden TX packet which exceed
1500 form application.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

On SDIO chips the firmware log does not impact performance. To make it
easier to debug firmware problems keep it enabled on the firmware.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Make sure the number of WBM_IDLE_LINK ring descriptors is power
of 2. This increases the number of descriptors to 32k from the
current ~18k to fix the target assert because of the shortage in
the descriptors in WBM_IDLE_LINK ring. Remove unnecessary
power of 2 calculation in ath11k_dp_link_desc_setup() as it is
not required after this change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

TLV length was 0 for TLV tag 'WMI_TAG_ARRAY_STRUCT' causing
Q6 to crash when trying to configure pktlog filter via debugfs.
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

skb_panic is hit during msdu coalescing whenever
enough tailroom is not allocated based on the remaining
msdu length which is spread across in different rx buffers.

Compute the extra length for resizing the skb based on
the total msdu length and the msdu length of the first buffer.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

remove unused counter to avoid taking locks inorder to optimize
cpu load.

Using Flamegraph, cpu usage of ath11k_dp_tx() observed to be decreased
from 5.58% to 3.74% with iperf traffic running with 80MHz bandwidth ap
mode.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In conf_tx() mac operation callback, we are truncating the tx
params cw_min and cw_max due to lower data type cast. so modified
the data type of cwmin and cwmax to avoid the trucation issue.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch drops ath11k_hal_rx_parse_dst_ring_desc(). This function was
creating a huge amount of load, which lead to a signifcant latency delay
when processing data in the RX path.

Pegging the processing on a specific core and running perf --top we get
the following output when running HE80 at a fixed bandwidth of 1gbit.

with patch
    19.19%  [ath11k]       [k] ath11k_dp_process_rx
     5.02%  [ath11k]       [k] ath11k_dp_rx_tid_del_func
     4.39%  [kernel]       [k] v7_dma_inv_range
     4.15%  [kernel]       [k] __slab_alloc.constprop.1
     4.03%  [kernel]       [k] dev_gro_receive
     3.86%  [kernel]       [k] tcp_gro_receive
     3.07%  [ip_tables]    [k] ipt_do_table
     2.96%  [kernel]       [k] dma_cache_maint_page

without patch
    21.64%  [ath11k]       [k] ath11k_hal_rx_parse_dst_ring_desc
    10.80%  [ath11k]       [k] ath11k_dp_process_rx
     3.77%  [kernel]       [k] v7_dma_inv_range
     3.48%  [kernel]       [k] dev_gro_receive
     3.32%  [ath11k]       [k] ath11k_dp_rx_tid_del_func
     3.17%  [mac80211]     [k] ieee80211_rx_napi
     2.70%  [kernel]       [k] dma_cache_maint_page
     2.65%  [mac80211]     [k] ieee80211_sta_ps_transition

When removing the the bandwidth limit and rerunning the test we see an
overall throughput improvement of 3-400mbit when running 4x4 HE80.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It is observed that ath11k STA mode UL throughput is low.
This is due to packets delivered to FW from TCL instead of TQM.
TCL AST search fail causes packet delivered to FW, fix this by
properly configuring the TCL address search type and ast_hash.
STA UL throughput is improved 10times with 11AC AP.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The current ath11k driver failed to parse
wmi_tlv_svc_rdy_ext_parse if there is change in
wmi_mac_phy_capabilities length with below error.

ath11k c000000.wifi1: failed to extract mac caps, idx :0
ath11k c000000.wifi1: failed to parse tlv -22

This is needed to get firmware version
WLAN.HK.2.0.0.1-00240-QCAHKSWPL_SILICONZ-1 working.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Handled the error case with proper resource cleanup and
moved the handling into a separate function from
ath11k_mac_sta_state.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The Previous configuartion of htt stats sounding info and pdev cca stats
are invalid due to that getting time out error.

Changing htt stats sounding info value from 0xFF to 0x00 and htt pdev cca
stats from 0x10 to 0x00
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

During driver load below warn logs are printed in the console if
firmware doesn't support some optional HTC services, ex:pktlog.
It is likely some older fw version may not support PKTLOG HTC
service as legacy fw uses HTC DATA service  for pktlog.
Move this log to debug level to remove un-necessary warn message
on console.

htc.c:803:  ath10k_warn(ar, "unsupported HTC service id: %d\n",
htc.c:881:  ath10k_warn(ar, "unsupported HTC service id: %d\n",
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trigger the WMI call en/disabling OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add target wait time wmi calls to the driver. En/disable the support
from when the bss_config changes. We ignore the cmd completion events.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>