When driver fails to start the heartbeat timer, exit from FW init.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For SRIOV based adapters, driver should not set the STOP_ADP bit as part of
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For Invader series, if FW supports more than 8 MSI-x vectors, driver needs
to enable combined reply queue mode. For Ventura series, driver enables
combined reply queue mode in case of more than 16 MSI-x vectors.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Module parameter description for rdpq_enable incorrectly lists the default
as enabled.  Also, provide range of valid values for resetwaittime in the
description.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

During init, if pci_alloc_irq_vectors() fails, the driver has not yet setup
the IRQs. Fix the goto labels and error handling for this case.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Change copyright to Broadcom Inc. Also update any references to Avago with
Broadcom. Update copyright duration wherever required.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For SAS3 and later controllers, FW sets the reset adapter bit indicating
the driver to perform a controller reset.  Driver needs to check if this
bit is set before doing a reset.  This reduces the driver probe failure
time to 180seconds in case there is a faulty controller connected.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In megasas_transition_to_ready() driver waits 180seconds for controller to
change FW state. Here we are calling msleep(1) in a loop for this.  As
explained in timers-howto.txt, msleep(1) will actually sleep longer than
1ms. If a faulty controller is connected, we will end up waiting for much
more than 180 seconds causing unnecessary delays during load.

Change the granularity of msleep() call from 1ms to 1000ms.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Latest firmware adds a mechanism to save firmware logs just before
controller reset on pre-allocated internal controller DRAM. This feature is
called snapdump which will help debugging firmware issues.  This feature
requires extra time and firmware reports these values through new driver
interface. Before initiating an OCR, driver needs to inform FW to save a
snapdump and then wait for a specified time for the snapdump to complete.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently driver checks for Firmware state change from ISR context, and
only when there are interrupts tied with no I/O completions.  We have seen
multiple cases where doorbell interrupts sent by firmware to indicate FW
state change are not processed by driver and it takes long time for driver
to trigger OCR. And if there are no IOs running, since we only check the FW
state as part of ISR code, fault goes undetected by driver and OCR will not
be triggered.

This patch introduces a separate workqueue that runs every one second to
detect Firmware FAULT state and trigger reset immediately.  As an
additional gain, removing PCI reads from ISR to check FW state results in
improved performance as well.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Modify driver version to 27.100.00.00 (which is equivalent to PH8 OOB
driver)
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently driver is modifying both current & NVRAM/persistent data in
Manufacturing page11. Driver should change only current copy of
Manufacturing page11. It should not modify the persistent data.

So removed the section of code where driver is modifying the persistent
data of Manufacturing page11.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If EEDPTagMode field in manufacturing page11 is set then unset it. This is
needed to fix a hardware bug only in SAS3/SAS2 cards. So, skipping
EEDPTagMode changes in Manufacturing page11 for SAS 3.5 controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This is to fix SYNC CACHE and START STOP command failures with
DID_NO_CONNECT during driver unload.

In driver's IO submission patch (i.e. in driver's .queuecommand()) driver
won't allow any SCSI commands to the IOC when ioc->remove_host flag is set
and hence SYNC CACHE commands which are issued to the target drives (where
write cache is enabled) during driver unload time is failed with
DID_NO_CONNECT status.

Now modified the driver to allow SYNC CACHE and START STOP commands to IOC,
even when remove_host flag is set.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Call sas_remove_host() before removing the target devices in the driver's
.remove() callback function(i.e. during driver unload time).  So that
driver can provide a way to allow SYNC CACHE, START STOP unit commands
etc. (which are issued from SML) to the target drives during driver unload
time.

Once sas_remove_host() is called before removing the target drives then
driver can just clean up the resources allocated for target devices and no
need to call sas_port_delete_phy(), sas_port_delete() API's as these API's
internally called from sas_remove_host().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

No functional change. Doing code refactor of function
mpt3sas_wait_for_ioc() for better readability.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

No functional changes. This section of code "wait for IOC to be
operational" is used in many places across the driver.  Factor this code
out into a new mpt3sas_wait_for_ioc().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Added new #define variable IOC_OPERATIONAL_WAIT_COUNT and it replaces hard
coded value '10' in all the places where driver is waiting for the IOC to
become operational.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add support for Aero/Sea controllers and add warning for configurable
secure type IOC.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Updating MPI headers to the latest version 2.6.7 to add support to the
driver to detect the new 3816 and 3916 chip based controllers.  Separate
out firmware image data from mpi2_ioc.h to new file mpi2_image.h
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

Pull scheduler fixes from Ingo Molnar:
 "A memory (under-)allocation fix and a comment fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/topology: Fix off by one bug
  sched/rt: Update comment in pick_next_task_rt()

Pull x86 fixes from Ingo Molnar:
 "A number of fixes and some late updates:

   - make in_compat_syscall() behavior on x86-32 similar to other
     platforms, this touches a number of generic files but is not
     intended to impact non-x86 platforms.

   - objtool fixes

   - PAT preemption fix

   - paravirt fixes/cleanups

   - cpufeatures updates for new instructions

   - earlyprintk quirk

   - make microcode version in sysfs world-readable (it is already
     world-readable in procfs)

   - minor cleanups and fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  compat: Cleanup in_compat_syscall() callers
  x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
  objtool: Support GCC 9 cold subfunction naming scheme
  x86/numa_emulation: Fix uniform-split numa emulation
  x86/paravirt: Remove unused _paravirt_ident_32
  x86/mm/pat: Disable preemption around __flush_tlb_all()
  x86/paravirt: Remove GPL from pv_ops export
  x86/traps: Use format string with panic() call
  x86: Clean up 'sizeof x' => 'sizeof(x)'
  x86/cpufeatures: Enumerate MOVDIR64B instruction
  x86/cpufeatures: Enumerate MOVDIRI instruction
  x86/earlyprintk: Add a force option for pciserial device
  objtool: Support per-function rodata sections
  x86/microcode: Make revision and processor flags world-readable

Pull perf updates and fixes from Ingo Molnar:
 "These are almost all tooling updates: 'perf top', 'perf trace' and
  'perf script' fixes and updates, an UAPI header sync with the merge
  window versions, license marker updates, much improved Sparc support
  from David Miller, and a number of fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
  perf intel-pt/bts: Calculate cpumode for synthesized samples
  perf intel-pt: Insert callchain context into synthesized callchains
  perf tools: Don't clone maps from parent when synthesizing forks
  perf top: Start display thread earlier
  tools headers uapi: Update linux/if_link.h header copy
  tools headers uapi: Update linux/netlink.h header copy
  tools headers: Sync the various kvm.h header copies
  tools include uapi: Update linux/mmap.h copy
  perf trace beauty: Use the mmap flags table generated from headers
  perf beauty: Wire up the mmap flags table generator to the Makefile
  perf beauty: Add a generator for MAP_ mmap's flag constants
  tools include uapi: Update asound.h copy
  tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
  tools include uapi: Update linux/fs.h copy
  perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
  perf cs-etm: Correct CPU mode for samples
  perf unwind: Take pgoff into account when reporting elf to libdwfl
  perf top: Do not use overwrite mode by default
  perf top: Allow disabling the overwrite mode
  perf trace: Beautify mount's first pathname arg
  ...

Pull irq fixes from Ingo Molnar:
 "An irqchip driver fix and a memory (over-)allocation fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
  irq/matrix: Fix memory overallocation

With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.

Fixed: 051f3ca0 ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes who have come in near or during the merge window:

   - Removal of a VLA usage in Marvell mpp platform code

   - Enable some IPMI options for ARM64 servers by default, helps
     testing

   - Enable PREEMPT on 32-bit ARMv7 defconfig

   - Minor fix for stm32 DT (removal of an unused DMA property)

   - Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
  ARM: orion: avoid VLA in orion_mpp_conf
  ARM: defconfig: Update multi_v7 to use PREEMPT
  arm64: defconfig: Enable some IPMI configs
  soc: ti: QMSS: Fix usage of irq_set_affinity_hint
  ARM: OMAP1: ams-delta: Fix impossible .irq < 0

Pull more arm64 updates from Catalin Marinas:

 - fix W+X page (mark RO) allocated by the arm64 kprobes code

 - Makefile fix for .i files in out of tree modules

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kprobe: make page to RO mode when allocate it
  arm64: kdump: fix small typo
  arm64: makefile fix build of .i file in external module case

Pull dma-mapping fix from Christoph Hellwig:
 "Avoid compile warnings on non-default arm64 configs"

* tag 'dma-mapping-4.20-2' of git://git.infradead.org/users/hch/dma-mapping:
  arm64: fix warnings without CONFIG_IOMMU_DMA

Pull Kbuild updates from Masahiro Yamada:

 - clean-up leftovers in Kconfig files

 - remove stale oldnoconfig and silentoldconfig targets

 - remove unneeded cc-fullversion and cc-name variables

 - improve merge_config script to allow overriding option prefix

* tag 'kbuild-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: remove cc-name variable
  kbuild: replace cc-name test with CONFIG_CC_IS_CLANG
  merge_config.sh: Allow to define config prefix
  kbuild: remove unused cc-fullversion variable
  kconfig: remove silentoldconfig target
  kconfig: remove oldnoconfig target
  powerpc: PCI_MSI needs PCI
  powerpc: remove CONFIG_MCA leftovers
  powerpc: remove CONFIG_PCI_QSPAN
  scsi: aha152x: rename the PCMCIA define

Pull cifs fixes and updates from Steve French:
 "Three small fixes (one Kerberos related, one for stable, and another
  fixes an oops in xfstest 377), two helpful debugging improvements,
  three patches for cifs directio and some minor cleanup"

* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix signed/unsigned mismatch on aio_read patch
  cifs: don't dereference smb_file_target before null check
  CIFS: Add direct I/O functions to file_operations
  CIFS: Add support for direct I/O write
  CIFS: Add support for direct I/O read
  smb3: missing defines and structs for reparse point handling
  smb3: allow more detailed protocol info on open files for debugging
  smb3: on kerberos mount if server doesn't specify auth type use krb5
  smb3: add trace point for tree connection
  cifs: fix spelling mistake, EACCESS -> EACCES
  cifs: fix return value for cifs_listxattr

Pull 9p fix from Al Viro:
 "Regression fix for net/9p handling of iov_iter; broken by braino when
  switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"

* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  iov_iter: Fix 9p virtio breakage

Pull more SCSI updates from James Bottomley:
 "This is a set of minor small (and safe changes) that didn't make the
  initial pull request plus some bug fixes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: mvsas: Remove set but not used variable 'id'
  scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
  scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
  scsi: qla2xxx: Remove a set-but-not-used variable
  scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
  scsi: qla2xxx: Declare local functions 'static'
  scsi: qla2xxx: Improve several kernel-doc headers
  scsi: qla2xxx: Modify fall-through annotations
  scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
  scsi: mvsas: Use dma_pool_zalloc
  scsi: target: Don't request modules that aren't even built
  scsi: target: Set response length for REPORT TARGET PORT GROUPS

Merge more updates from Andrew Morton:

 - more ocfs2 work

 - various leftovers

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  memory_hotplug: cond_resched in __remove_pages
  bfs: add sanity check at bfs_fill_super()
  kernel/sysctl.c: remove duplicated include
  kernel/kexec_file.c: remove some duplicated includes
  mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
  ocfs2: fix clusters leak in ocfs2_defrag_extent()
  ocfs2: dlmglue: clean up timestamp handling
  ocfs2: don't put and assigning null to bh allocated outside
  ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
  ocfs2: don't use iocb when EIOCBQUEUED returns
  ocfs2: without quota support, avoid calling quota recovery
  ocfs2: remove ocfs2_is_o2cb_active()
  mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
  include/linux/notifier.h: SRCU: fix ctags
  mm: handle no memcg case in memcg_kmem_charge() properly

We have received a bug report that unbinding a large pmem (>1TB) can
result in a soft lockup:

  NMI watchdog: BUG: soft lockup - CPU#9 stuck for 23s! [ndctl:4365]
  [...]
  Supported: Yes
  CPU: 9 PID: 4365 Comm: ndctl Not tainted 4.12.14-94.40-default #1 SLE12-SP4
  Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.01.00.0833.051120182255 05/11/2018
  task: ffff9cce7d4410c0 task.stack: ffffbe9eb1bc4000
  RIP: 0010:__put_page+0x62/0x80
  Call Trace:
   devm_memremap_pages_release+0x152/0x260
   release_nodes+0x18d/0x1d0
   device_release_driver_internal+0x160/0x210
   unbind_store+0xb3/0xe0
   kernfs_fop_write+0x102/0x180
   __vfs_write+0x26/0x150
   vfs_write+0xad/0x1a0
   SyS_write+0x42/0x90
   do_syscall_64+0x74/0x150
   entry_SYSCALL_64_after_hwframe+0x3d/0xa2
  RIP: 0033:0x7fd13166b3d0

It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large.  Fix the issue by calling
cond_resched once per memory section.

Link: http://lkml.kernel.org/r/20181031125840.23982-1-mhocko@kernel.orgSigned-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>