* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
  block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
  xen-blkfront: fix missing out label
  blkdev: fix blkdev_issue_zeroout return value
  block: update request stacking methods to support discards
  block: fix missing export of blk_types.h
  writeback: fix bad _bh spinlock nesting
  drbd: revert "delay probes", feature is being re-implemented differently
  drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
  drbd: Disable delay probes for the upcomming release
  writeback: cleanup bdi_register
  writeback: add new tracepoints
  writeback: remove unnecessary init_timer call
  writeback: optimize periodic bdi thread wakeups
  writeback: prevent unnecessary bdi threads wakeups
  writeback: move bdi threads exiting logic to the forker thread
  writeback: restructure bdi forker loop a little
  writeback: move last_active to bdi
  writeback: do not remove bdi from bdi_list
  writeback: simplify bdi code a little
  writeback: do not lose wake-ups in bdi threads
  ...

Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (94 commits)
  V4L/DVB: tvp7002: fix write to H-PLL Feedback Divider LSB register
  V4L/DVB: dvb: siano: free spinlock before schedule()
  V4L/DVB: media: video: pvrusb2: remove custom hex_to_bin()
  V4L/DVB: drivers: usbvideo: remove custom implementation of hex_to_bin()
  V4L/DVB: Report supported QAM modes on bt8xx
  V4L/DVB: media: ir-keytable: null dereference in debug code
  V4L/DVB: ivtv: convert to the new control framework
  V4L/DVB: ivtv: convert gpio subdev to new control framework
  V4L/DVB: wm8739: convert to the new control framework
  V4L/DVB: cs53l32a: convert to new control framework
  V4L/DVB: wm8775: convert to the new control framework
  V4L/DVB: cx2341x: convert to the control framework
  V4L/DVB: cx25840: convert to the new control framework
  V4L/DVB: cx25840/ivtv: replace ugly priv control with s_config
  V4L/DVB: saa717x: convert to the new control framework
  V4L/DVB: msp3400: convert to the new control framework
  V4L/DVB: saa7115: convert to the new control framework
  V4L/DVB: v4l2: hook up the new control framework into the core framework
  V4L/DVB: Documentation: add v4l2-controls.txt documenting the new controls API
  V4L/DVB: v4l2-ctrls: Whitespace cleanups
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: hpwdt: formatting of pointers in printk()
  watchdog: Adding support for ARM Primecell SP805 Watchdog
  watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG
  watchdog: sch311x_wdt.c: set parent before registeriing the misc device in probe() function
  watchdog: wdt_pci.c: move ids to pci_ids.h
  watchdog: s3c2410_wdt - Fix removing of platform device

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cxgb4: Obtain RDMA QID ranges from LLD/FW

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add USB-ID for PL-3601 Xbox 360 pad
  Input: cy8ctmg100_ts - signedness bug
  Input: elantech - report position also with 3 fingers
  Input: elantech - discard the first 2 positions on some firmwares
  Input: adxl34x - do not mark device as disabled on startup
  Input: gpio_keys - add hooks to enable/disable device
  Input: evdev - rearrange ioctl handling
  Input: dynamically allocate ABS information
  Input: switch to input_abs_*() access functions
  Input: add static inline accessors for ABS properties

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (148 commits)
  USB: serial: fix stalled writes
  USB: remove fake "address-of" expressions
  USB: fix thread-unsafe anchor utiliy routines
  USB: usbtest: support test device with only one iso-in or iso-out endpoint
  USB: usbtest: avoid to free coherent buffer in atomic context
  USB: xhci: Set DMA mask for host.
  USB: xhci: Don't flush doorbell writes.
  USB: xhci: Reduce reads and writes of interrupter registers.
  USB: xhci: Make xhci_set_hc_event_deq() static.
  USB: xhci: Minimize HW event ring dequeue pointer writes.
  USB: xhci: Make xhci_handle_event() static.
  USB: xhci: Remove unnecessary reads of IRQ_PENDING register.
  USB: xhci: Performance - move xhci_work() into xhci_irq()
  USB: xhci: Performance - move interrupt handlers into xhci-ring.c
  USB: xhci: Performance - move functions that find ep ring.
  USB:: fix linux/usb.h kernel-doc warnings
  USB: add USB serial ssu100 driver
  USB: usb-storage: implement autosuspend
  USB: ehci: fix remove of ehci debugfs dir
  USB: Add USB 2.0 to ssb ohci driver
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (68 commits)
  U6715 16550A serial driver support
  Char: nozomi, set tty->driver_data appropriately
  Char: nozomi, fix tty->count counting
  serial: max3107: Fix gpiolib support
  hsu: call PCI pm hooks in suspend/resume function
  hsu: some code cleanup
  hsu: add a periodic timer to check dma rx channel
  hsu: driver for Medfield High Speed UART device
  mxser: remove unnesesary NULL check
  serial: add support for OX16PCI958 card
  serial: 68328serial.c: remove dead (ALMA_ANS | DRAGONIXVZ | M68EZ328ADS)
  timbuart: use __devinit and __devexit macros for probe and remove
  serial: MMIO32 support for 8250_early.c
  serial: mcf: don't take spinlocks in already protected functions
  serial: general fixes in the serial_rs485 structure
  serial: fix missing bit coverage of ASYNC_FLAGS
  serial: "altera_uart: simplify altera_uart_console_putc()" checkpatch fixes
  serial: crisv10: formatting of pointers in printk()
  vt: Fix warning: statement with no effect due to vt_kern.h
  tty_io: remove casts from void*
  ...

As David VomLehn points out, it was possible to receive an interrupt
before clearing the free-urb flag which could lead to the urb being
incorrectly marked as busy.

For the same reason, move tx_bytes accounting so that it will never be
negative.

Note that the free-flags set and clear operations do not need any
additional locking as they are manipulated while USB_SERIAL_WRITE_BUSY
is set.
Reported-by: David VomLehn <dvomlehn@cisco.com>
Tested-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fake "address-of" expressions that evaluate to NULL generally confuse
readers and can provoke compiler warnings.  This patch (as1412)
removes three such fake expressions, using "#ifdef"s in their place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes a race condition in two utility routines
related to the removal/unlinking of urbs from an anchor.

If two threads are concurrently accessing the same anchor,
both could end up with the same urb - thinking they are
the exclusive owner.

Alan Stern pointed out a related issue in
usb_unlink_anchored_urbs:

"The URB isn't removed from the anchor until it completes
 (as a by-product of completion, in fact), which might not
 be for quite some time after the unlink call returns.
 In the meantime, the subroutine will keep trying to unlink
 it, over and over again."

Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It is very common that one altsetting may include only one iso-in or iso-out
single endpoint, especially for high bandwidth endpoint, so support it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes the warning below:
[30753.755998] ------------[ cut here ]------------
[30753.755998] WARNING: at /home/tom/git/linux-2.6/linux-2.6-next/arch/x86/include/asm/dma-mapping.h:155 hcd_buffer_free+0xb1/0xd4 [usbcore]()
[30753.755998] Hardware name: 6475EK2
[30753.755998] Modules linked in: uvcvideo ehci_hcd usbtest cdc_ether usbnet vfat fat usb_storage nfsd lockd nfs_acl auth_rpcgss exportfs mii tun videodev v4l1_compat v4l2_compat_ioctl32 fuse bridge stp llc sunrpc ipv6 cpufreq_ondemand acpi_cpufreq freq_table mperf kvm_intel kvm arc4 ecb ath5k usbhid mac80211 snd_hda_codec_conexant ch341 usbserial ath cfg80211 thinkpad_acpi snd_hda_intel pcspkr wmi hwmon yenta_socket iTCO_wdt iTCO_vendor_support i2c_i801 e1000e snd_hda_codec snd_hwdep snd_pcm snd_timer snd soundcore snd_page_alloc pata_acpi uhci_hcd ohci_hcd usbcore i915 drm_kms_helper drm i2c_algo_bit i2c_core video output [last unloaded: uvcvideo]
[30753.755998] Pid: 0, comm: swapper Tainted: G        W   2.6.35-rc6-gkh-wl+ #49
[30753.755998] Call Trace:
[30753.755998]  <IRQ>  [<ffffffff8104478a>] warn_slowpath_common+0x80/0x98
[30753.755998]  [<ffffffff810447b7>] warn_slowpath_null+0x15/0x17
[30753.755998]  [<ffffffffa00ce02d>] hcd_buffer_free+0xb1/0xd4 [usbcore]
[30753.755998]  [<ffffffffa00c1345>] usb_free_coherent+0x1c/0x1e [usbcore]
[30753.755998]  [<ffffffffa00b13e4>] simple_free_urb+0x23/0x2f [usbtest]
[30753.755998]  [<ffffffffa00b210b>] iso_callback+0xbb/0x10f [usbtest]
[30753.755998]  [<ffffffffa00c7390>] usb_hcd_giveback_urb+0x8c/0xc0 [usbcore]
[30753.755998]  [<ffffffffa0449b35>] ehci_urb_done+0x84/0x95 [ehci_hcd]
[30753.755998]  [<ffffffffa044b5a5>] ehci_work+0x41a/0x7dd [ehci_hcd]
[30753.755998]  [<ffffffffa044e298>] ehci_irq+0x33b/0x370 [ehci_hcd]
[30753.755998]  [<ffffffff8100fb05>] ? sched_clock+0x9/0xd
[30753.755998]  [<ffffffff8105e641>] ? sched_clock_local+0x1c/0x82
[30753.755998]  [<ffffffff8105e76a>] ? sched_clock_cpu+0xc3/0xce
[30753.755998]  [<ffffffff81067c7e>] ? trace_hardirqs_off+0xd/0xf
[30753.755998]  [<ffffffff8105e7b8>] ? cpu_clock+0x43/0x5e
[30753.755998]  [<ffffffffa00c6999>] usb_hcd_irq+0x45/0xa1 [usbcore]
[30753.755998]  [<ffffffff81092e02>] handle_IRQ_event+0x20/0xa5
[30753.755998]  [<ffffffff81094cea>] handle_fasteoi_irq+0x92/0xd2
[30753.755998]  [<ffffffff8100c0ed>] handle_irq+0x1f/0x2a
[30753.755998]  [<ffffffff8100b75d>] do_IRQ+0x57/0xbe
[30753.755998]  [<ffffffff8136a693>] ret_from_intr+0x0/0x16
[30753.755998]  <EOI>  [<ffffffff81223baa>] ? acpi_idle_enter_bm+0x231/0x269
[30753.755998]  [<ffffffff81223ba3>] ? acpi_idle_enter_bm+0x22a/0x269
[30753.755998]  [<ffffffff812c4b6b>] cpuidle_idle_call+0x99/0xce
[30753.755998]  [<ffffffff81008dd5>] cpu_idle+0x61/0xaa
[30753.755998]  [<ffffffff8136374b>] start_secondary+0x1c2/0x1c6
[30753.755998] ---[ end trace 904cfaf7ab4cb1a2 ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Tell the USB core that we can do DMA directly (instead of needing it to
memory-map the buffers for PIO).  If the xHCI host supports 64-bit addresses,
set the DMA mask accordingly.  Otherwise indicate the host can handle 32-bit DMA
addresses.

This improves performance because the USB core doesn't have to spend time
remapping buffers in high memory into the 32-bit address range.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

To tell the host controller that there are transfers on the endpoint
rings, we need to ring the endpoint doorbell.  This is a PCI MMIO write,
which can be delayed until another register read is queued.

The previous code would flush the doorbell write by reading the doorbell
register after the write.  This may take time, and it's not necessary to
force the host controller to know about the transfers right away.  Don't
flush the doorbell register writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The interrupter register set includes a register that says whether interrupts
are pending for each event ring (the IP bit).  Each MSI-X vector will get its
own interrupter set with separate IP bits.  The status register includes an
"Event Interrupt (EINT)" bit that is set when an IP bit is set in any of the
interrupters.

When PCI interrupts are used, the EINT bit exactly mirrors the IP bit in the
single interrupter set, and it is a waste of time to check both registers when
trying to figure out if the xHC interrupted or another device on the shared IRQ
line interrupted.  Only check the IP bit to reduce register reads.

The IP bit is automatically cleared by the xHC when MSI or MSI-X is enabled.  It
doesn't make sense to read that register to check for shared interrupts (since
MSI and MSI-X aren't shared).  It also doesn't make sense to write to that
register to clear the IP bit, since it is cleared by the hardware.

We can tell whether MSI or MSI-X is enabled by looking at the irq number in
hcd->irq.  If it's -1, we know MSI or MSI-X is enabled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Now that the event handler functions no longer use xhci_set_hc_event_deq()
to update the event ring dequeue pointer, that function is not used by
anything in xhci-ring.c.  Move that function into xhci-mem.c and make it
static.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The xHCI specification suggests that writing the hardware event ring dequeue
pointer register too often can be an expensive operation for the xHCI hardware
to manage.  It suggests minimizing the number of writes to that register.

Originally, the driver wrote the event ring dequeue pointer after each
event was processed.  Depending on how the event ring moderation register
is set up and how fast the transfers are completing, there may be several
events processed for each interrupt.  This patch makes the hardware event
ring dequeue pointer be written only once per interrupt.

Make the transfer event handler and port status event handler only write
the software event ring dequeue pointer.  Move the updating of the
hardware event ring dequeue pointer into the interrupt function.  Move the
contents of xhci_set_hc_event_deq() into the interrupt handler.  The
interrupt handler must clear the event handler busy flag, so it might as
well also write the dequeue pointer to the same register.  This eliminates
two 32-bit PCI reads and two 32-bit PCI writes.
Reported-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

xhci_handle_event() is now only called from within xhci-ring.c, so make it
static.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Remove a duplicate register read of the interrupt pending register from
xhci_irq().  Also, remove waiting on the posted write of that register.
The host will see it eventually.  It will probably read the register
itself before deciding whether to interrupt the system again, forcing the
posted write to complete.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When we move xhci_work() into xhci_irq(), we don't need to read the operational
register status field twice.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Most of the work for interrupt handling is done in xhci-ring.c, so it makes
sense to move the functions that are first called when an interrupt happens
(xhci_irq() or xhci_msi_irq()) into xhci-ring.c, so that the compiler can better
optimize them.

Shorten some lines to make it pass checkpatch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I've been using perf to measure the top symbols while transferring 1GB of data
on a USB 3.0 drive with dd.  This is using the raw disk with /dev/sdb, with a
block size of 1K.

During performance testing, the top symbol was xhci_triad_to_transfer_ring(), a
function that should return immediately if streams are not enabled for an
endpoint.  It turned out that the functions to find the endpoint ring was
defined in xhci-mem.c and used in xhci-ring.c and xhci-hcd.c.  I moved a copy of
xhci_triad_to_transfer_ring() and xhci_urb_to_transfer_ring() into xhci-ring.c
and declared them static.  I also made a static version of
xhci_urb_to_transfer_ring() in xhci.c.

This improved throughput on a 1GB read of the raw disk with dd from
186MB/s to 195MB/s, and perf reported sampling the xhci_triad_to_transfer_ring()
0.06% of the time, rather than 9.26% of the time.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix kernel-doc warnings in linux/usb.h:

Warning(include/linux/usb.h:185): No description found for parameter 'resetting_device'
Warning(include/linux/usb.h:1212): No description found for parameter 'stream_id'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add support for the Quatech SSU-100 single port usb to serial device.
This driver is based on the ftdi_sio.c driver and the original
serqt_usb driver from Quatech.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1400) adds runtime-PM support to usb-storage.  It
utilizes the SCSI layer's runtime-PM implementation, so its scope is
limited.  Currently the only effect is that disk-like devices (such as
card readers or flash drives) will be autosuspended if they aren't
mounted and their device files aren't open.  This would apply, for
example, to card readers that don't contain a memory card.

Unfortunately this won't interact very well with the removable-media
polling normally carried out by hal or DeviceKit.  Maybe those
programs can be changed to use a longer polling interval, or maybe the
default autosuspend time for usb-storage should be set to something
below 1 second.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The patch below on gregkh tree only creates 'lpm' file under
ehci->debug_dir, but not removes it when unloading module,

	 USB: EHCI: EHCI 1.1 addendum: preparation

which can make loading of ehci-hcd module failed after unloading it.

This patch replaces debugfs_remove with debugfs_remove_recursive
to remove ehci debugfs dir and files. It does fix the bug above,
and may simplify the removing procedure.

Also, remove the debug_registers, debug_async and debug_periodic
field from ehci_hcd struct since they are useless now.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds USB 2.0 support to ssb ohci driver.
This patch was used in OpenWRT for a long time now.

CC: Steve Brown <sbrown@cortland.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch is to add a US Interface, Inc. "Navigator" USB device.
Specifically, it's a HAM Radio USB sound modem that also
incorporates three pairs of unique FTDI serial ports.  The standard
Linux FTDI serial driver will only recognize the first two serial
ports of an unknown FDTI derived device and this patch adds in
recognition to these specific new IDs.
Signed-off-by: David A. Ranch <dranch@trinnet.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1410) makes a slight change to the strategy used for
choosing a default configuration.  Currently we skip configs whose
first interface is RNDIS, if the kernel wasn't built with the
corresponding driver.  This risks losing access to the other
interfaces in those configs.  In addition, if there is only one config
then we will end up not configuring the device at all.

This changes the logic; now such configurations will be skipped only
if there is at least one other config.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds the product IDs of Huawei's K3765 and K4505 mobile
broadband usb modems to option.c. It also adds a quirk to the option
probe function so that binding to the device's network interface(class
0xff) is avoided. This is necessary to allow another driver to bind to
that, and to avoid programs like wvdial opening a nonfunctioning tty
during modem discovery.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Moved the serial parameter handling code out of "#ifdef
CONFIG_USB_FILE_STORAGE_TEST".

This modifies Yann Cantin's commit "USB: Add a serial number
parameter to g_file_storage" module as per Alan Stern's request.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Yann Cantin <yann.cantin@laposte.net>

imx21_hc_reset() uses schedule_timeout() without setting state to
STATE_(UN)INTERRUPTIBLE. As it is called in cycle without checking of
pending signals, use schedule_timeout_uninterruptible().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will
enable support for the Segway Robotic Mobility Platform (RMP200) in the
ftdi_sio kernel module.  Currently, users of the Segway RMP200 must use
a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a
udev rule to get the ftdi_sio module to handle the usb interface and
mount it on /dev/ttyXXX.  This is not a good solution because some users
will have multiple USB to Serial converters which will use the ftdi_sio
module.
Signed-off-by: John Rogers <jgrogers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for clock gating of the HS/OTG block. On S5PV210
otg gating clock is initally disabled so the driver needs to get and
enable it before it can access its registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

S5PV210 SoCs has 2 USB PHY interfaces, both enabled by writing zero to
S3C_PHYPWR register. HS/OTG driver uses only PHY0, so do not touch bits
related to PHY1.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/gadget/s3c-hsotg.c: In function ‘s3c_hsotg_otgreset’:
drivers/usb/gadget/s3c-hsotg.c:2816: error: ‘MHZ’ undeclared (first use in this function)
drivers/usb/gadget/s3c-hsotg.c:2816: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/s3c-hsotg.c:2816: error: for each function it appears in.)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz.
This patch adds support to the USB driver for setting the correct register bit
according to the given clock.

This depends on the following patch:
[PATCH] ARM: S3C64XX: Add USB external clock definition
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If there is more data in the request than we could fit into a single
hardware request, then check when the OutDone event is received if
we have more data, and if so, schedule the new data instead of trying
to complete the request (and in the case of EP0, sending a 0 packet
in the middle of a transfer).

Also, move the debug message about the current transfer state before
the warning about a bad transfer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The EP0 out limit is the same as the IN limit, so make them the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>