AT91 DT for v6.1 #2

It contains:
- new SAMA5D3 based board, namely SAMA5D3-EDS
- adjustments to pass the DT binding validations
- disable AES on some LAN966 based boards as they are reserverd by
  secure OS

* tag 'at91-dt-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  spi: dt-bindings: atmel,at91rm9200-spi: Add DMA related properties
  ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
  ARM: dts: at91: sam9x60ek: Add DBGU compatibles to uart1
  ARM: dts: at91: sama7g5: Swap rx and tx for spi11
  dts: arm: at91: Add SAMA5D3-EDS Board
  dt-bindings: arm: at91: Add info on SAMA5D3-EDS
  ARM: dts: lan966x: disable aes

Link: https://lore.kernel.org/r/20220916105407.1287452-1-claudiu.beznea@microchip.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The DT nodes of the SPI IP's may contain DMA related properties so
make sure that the binding is able to properly validate those as
well by making it aware of these optional properties.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-5-sergiu.moga@microchip.com

Add the missing required DT property `atmel,usart-mode` to the serial
nodes of Atmel/Microchip DT files.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-4-sergiu.moga@microchip.com

Maintain consistency among the compatibles of the serial nodes of
sam9x60ek and highlight the incremental characteristic of its serial
IP's by making sure that all serial nodes contain both the sam9x60
and sam9260 usart/dbgu compatibles.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-3-sergiu.moga@microchip.com

Swap the rx and tx of the DMA related DT properties of the spi11 node
in order to maintain consistency across Microchip/Atmel SoC files.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-2-sergiu.moga@microchip.com

This pull request contains Broadcom ARM64-based SoC changes for 6.1,
please pull the following:

- Rafal adds the BCM4908 LED controller node and describes all 32 LED
pins, he also adds support for the Asus GC-AC5300 LEDs

* tag 'arm-soc/for-6.1/devicetree-arm64' of https://github.com/Broadcom/stblinux:
  arm64: dts: broadcom: bcm4908: add Asus GT-AC5300 LEDs
  arm64: dts: broadcom: bcm4908: add LEDs controller block
  arm64: dts: broadcom: bcm4908: add remaining LED pins

Link: https://lore.kernel.org/r/20220915023044.2350782-3-f.fainelli@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

This pull request contains Broadcom ARM-based SoC Device Tree updates
for 6.1, please pull the following:

- Rafal improves the BCM5301X PCIe DT nodes schema validation by
flagging the PCIe controller with a missing "device_type" property

- William merges BCM4908 within BCMBCA since this chip is part of the
Broadcom Broadband Carrier Access group and follows the architecture of
those chips

* tag 'arm-soc/for-6.1/devicetree' of https://github.com/Broadcom/stblinux:
  arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA
  arm64: dts: Add BCM4908 generic board dts
  arm64: dts: Move BCM4908 dts to bcmbca folder
  arm64: dts: bcmbca: update BCM4908 board dts files
  dt-bindings: arm64: bcmbca: Update BCM4908 description
  dt-bindings: arm64: bcmbca: Merge BCM4908 into BCMBCA
  ARM: dts: BCM5301X: Add basic PCI controller properties

Link: https://lore.kernel.org/r/20220915023044.2350782-2-f.fainelli@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The SAMA5D3-EDS board is an Ethernet Development Platform allowing for
evaluating many Microchip ethernet switch and PHY products.  Various
daughter cards can connect via an RGMII connector or an RMII connector.

The EDS board is not intended for stand-alone use and has no ethernet
capabilities when no daughter board is connected.  As such, this device
tree is intended to be used with a DT overlay defining the add-on board.
To better ensure consistency, some items are defined here as a form of
documentation so that all add-on overlays will use the same terms.

Link: https://www.microchip.com/en-us/development-tool/SAMA5D3-ETHERNET-DEVELOPMENT-SYSTEMSigned-off-by: Jerry Ray <jerry.ray@microchip.com>
[claudiu.beznea: s/gpio-inputs/gpio-keys in at91-sama5d3_eds.dts]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909163022.13022-2-jerry.ray@microchip.com

Adding the SAMA5D3-EDS board from Microchip into the atmel AT91 board
description yaml file.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909163022.13022-1-jerry.ray@microchip.com

Disable AES node on lan966x pcb8290, pcb891 and pcb8309 because these
boards have lan966x that uses secure OS which reserves the AES block.
Therefore it can't be exposed to non-secure world.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220908070451.3730608-1-horatiu.vultur@microchip.com

Merge tag 'samsung-dt64-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt

Samsung DTS ARM64 changes for v6.0

1. Add binding headers for several Exynos850 and ExynosAutov9 clocks.
2. ExynosAutov9: Add FSYS clock controller nodes.
3. ExynosAutov9: Document serial compatible (used in DTS).
4. Exynos850: Add Audio, IS, MFC clock controllers. Add IOMMU nodes.

* tag 'samsung-dt64-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  dt-bindings: serial: samsung: add exynosautov9-uart compatible
  arm64: dts: exynos: Add SysMMU nodes for Exynos850
  arm64: dts: exynos: Add CMU_AUD, CMU_IS and CMU_MFCMSCL for Exynos850
  arm64: dts: exynosautov9: add fsys0/1 clock DT nodes
  dt-bindings: clock: exynos850: Add Exynos850 CMU_MFCMSCL
  dt-bindings: clock: exynos850: Add Exynos850 CMU_IS
  dt-bindings: clock: exynos850: Add Exynos850 CMU_AUD
  dt-bindings: clock: exynosautov9: add schema for cmu_fsys0/1
  dt-bindings: clock: exynosautov9: add fsys1 clock definitions
  dt-bindings: clock: exynosautov9: add fys0 clock definitions
  dt-bindings: clock: exynosautov9: correct clock numbering of peric0/c1

Link: https://lore.kernel.org/r/20220909150849.820523-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'stm32-dt-for-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT for v6.1, round 1

Highlights:
----------

- MPU:
  - General:
    - Add I2C support (5 instances) on STM32MP13.
    - Add SPI support (5 instabces) on STM32MP13.
    - Add timer interrupts support on STM32MP15.

  - ST boards:
    - Enable I2C1 and I2C5 on stm32mp135f-dk board.
    - Add SPI5 on stm32mp135f-dk board but disabled as only available on
      the GPIO expansion connector.

  - ARGON:
    - Remove spidev node as not used by the code.

* tag 'stm32-dt-for-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: argon: remove spidev node
  ARM: dts: stm32: Create separate pinmux for qspi cs pin in stm32mp15-pinctrl.dtsi
  ARM: dts: stm32: Fix typo in license text for Engicam boards
  ARM: dts: stm32: Add timer interrupts on stm32mp15
  ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk
  ARM: dts: stm32: add spi nodes into stm32mp131.dtsi
  ARM: dts: stm32: enable i2c1 and i2c5 on stm32mp135f-dk.dts
  ARM: dts: stm32: add i2c nodes into stm32mp131.dtsi

Link: https://lore.kernel.org/r/d80afc20-2745-24a2-ab70-a5a03439bd50@foss.st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'v6.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt

Adapt emac nodes to make them conform to the newly yaml-converted binding.

* tag 'v6.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: restyle emac nodes
  ARM: dts: rockchip: fix rk3036 emac node compatible string

Link: https://lore.kernel.org/r/4766760.31r3eYUQgx@philSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'v6.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt

New boards the Anberic RG353P and RG503, Radxa Rock4c+ (variant with
different display outputs), Pine64 Pinephone Pro, Open AI Lab EAIDK-610.

New components of the rk356x (Video encoder/decoder, pcie, CSI dphy).

New board-peripherals for rock3a (pcie, i2c, regulators, rtc), quartz64-b
(pcie, analog audio) and BPI-R2-Pro (pcie), ROCK Pi (leds), Odroid Go (charger)

Usage of the new-ish bclk special handling for audio on rk3399.

* tag 'v6.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
  arm64: dts: rockchip: use BCLK to GPIO switch on rk3399
  arm64: dts: rockchip: Add Hantro encoder node to rk356x
  arm64: dts: rockchip: Add VPU support for RK3568/RK3566
  arm64: dts: rockchip: Enable PCIe controller on rock3a
  arm64: dts: rockchip: add rtc to rock3a
  arm64: dts: rockchip: Add PCIe 2 nodes to quartz64-b
  arm64: dts: rockchip: add Anbernic RG353P and RG503
  dt-bindings: arm: rockchip: Add Anbernic RG353P and RG503
  dt-bindings: vendor-prefixes: add Anbernic
  arm64: dts: rockchip: Add regulator suffix to BPI-R2-Pro
  arm64: dts: rockchip: add LEDs for ROCK 4C+
  arm64: dts: rockchip: add LED for ROCK Pi 4A/B/C/A+/B+
  arm64: dts: rockchip: add rk817 chg to Odroid Go Advance
  arm64: dts: rockchip: Fix SD card controller probe on Pinephone Pro
  arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
  arm64: dts: rockchip: Add RK3399-T OPP table
  dt-bindings: arm: rockchip: Document Radxa ROCK 4C+
  arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
  dt-bindings: arm: rockchip: Add PinePhone Pro bindings
  arm64: dts: rockchip: Add dts for a rk3399 based board EAIDK-610
  ...

Link: https://lore.kernel.org/r/5600929.DvuYhMxLoT@philSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Commit 956b200a ("spi: spidev: Warn loudly if instantiated from DT
as "spidev"") states that there should not be spidev nodes in DTs.
Remove this non-HW description. There won't be a regression because it
won't bind since 2015 anyhow.

Fixes: 16e3e44c ("ARM: dts: stm32: Add support for the emtrion emSBC-Argon")
Cc: Reinhold Mueller <reinhold.mueller@emtrion.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Create a separate pinmux for qspi chip select in stm32mp15-pinctrl.dtsi.
In the case we want to use transfer_one() API to communicate with a SPI
device, chip select signal must be driven individually.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix the Amarula Solutions typo mistake in license text added in below
commits.

commit <3ff0810f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0 10.1" OF")
commit <6ca2898d> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")
commit <adc04961> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")
commit <30f9a9da> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
SoM")
commit <1d278204> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")
commit <f838dae7> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")
commit <0be81dfa> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
SoM")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add pinctrl information and a disabled spi5 node within
stm32mp135f-dk.dts in order to use the spi5 bus which is
available via the GPIO expansion pins of the STM32MP135 Discovery board.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add the 5 instances of spi busses supported by the stm32mp131.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Enable the two i2c busses i2c1 and i2c5 available on the
stm32mp135f-dk Discovery board.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add the 5 instances of i2c busses supported by the stm32mp131.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.

In order to:
  1. prevent BCLK from turning on by other component.
  2. keep BCLK and LRCLK being present at the same time

This patch adjusts the device tree to allow BCLK to switch
to GPIO func before LRCLK output, and switch back during
LRCLK is output.
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220708080726.4170711-1-judyhsiao@chromium.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The RK3566 and RK3568 come with a dedicated Hantro instance solely for
encoding. This patch adds a node for this to the device tree, along with
a node for its MMU.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20220612155346.16288-4-frattaroli.nicolas@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

RK356x has Hantro G1 video decoder capable to decode MPEG2/H.264/VP8
video formats.

This patch enables RK356x video decoder in RK356x device-tree
include.

Tested on [1] with FFmpeg v4l2_request code taken from [2]
with MPEG2, H.642 and VP8 samples with results [3].

[1] https://github.com/warpme/minimyth2
[2] https://github.com/LibreELEC/LibreELEC.tv/blob/master/packages/multimedia/ffmpeg/patches/v4l2-request/ffmpeg-001-v4l2-request.patch
[3] https://github.com/warpme/minimyth2/blob/master/video-test-summary.txtSigned-off-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Link: https://lore.kernel.org/r/20220214212955.1178947-2-piotr.oniszczuk@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the nodes to enable the PCIe controller on the
Radxa ROCK3 Model A board. Run test with the MT7921
pcie wireless card.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20220726023516.6487-1-amadeus@jmu.edu.cnSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add devicetree node for hym8563 rtc to
Radxa ROCK3 Model A board.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20220726023046.5876-1-amadeus@jmu.edu.cnSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds the regulator node to the quartz64-b device tree,
and enables the PCIe 2 controller and combphy for it.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20220718033145.792657-1-frattaroli.nicolas@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The emac_rockchip.txt file is converted to YAML.
Phy nodes are now a subnode of mdio, so restyle
the emac nodes of rk3036/rk3066/rk3188.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20220603163539.537-3-jbx6244@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The Linux kernel has no logic to decide which driver to probe first.
To prevent race conditions remove the rk3036 emac node
fall back compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20220603163539.537-2-jbx6244@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices
from Anbernic.

Both devices have:
 - 2 SDMMC slots.
 - A Realtek rtl8821cs WiFi/Bluetooth adapter.
 - A mini HDMI port.
 - A USB C host port and a USB C otg port (currently only working as
   device).
 - Multiple GPIO buttons and a single ADC button.
 - Dual analog joysticks controlled via a GPIO mux.
 - A headphone jack with amplified stereo speakers via a SGM4865 amp.
 - A PWM based vibrator for force feedback.

The RG353P has:
 - 2GB LPDDR4 RAM.
 - A 32GB eMMC.
 - A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
   controlled touchscreen (touchscreen is a Hynitron CST340).

The RG503 has:
 - 1GB LPDDR4 RAM.
 - A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
   with part number ams495qa04. Data for this panel is provided via the
   DSI interface, however commands are sent via a 9-bit 3-wire SPI
   interface. The MISO pin of SPI3 of the SOC is wired to the input of
   the panel, so it must be bitbanged.

This devicetree enables the following hardware:
 - HDMI (plus audio).
 - Analog audio, including speakers.
 - All buttons.
 - All SDMMC/eMMC/SDIO controllers.
 - The ADC joysticks (note a pending patch is required to use them).
 - WiFi/Bluetooth (note out of tree drivers are required).
 - The PWM based vibrator motor.

The following hardware is not enabled:
 - The display panels (drivers are being written and there are issues
   with the upstream DSI and VOP2 subsystems).
 - Battery (driver pending).
 - Touchscreen on the RG353P (note the i2c2 bus is enabled for it).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20220906210324.28986-4-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add entry for the Anbernic RG353P and RG503 handheld devices.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220906210324.28986-3-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Anbernic designs and manufactures portable gaming systems.
https://anbernic.com/Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220906210324.28986-2-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add -regulator suffix to regulator names on Banana Pi R2 Pro board as
discussed on Mailinglist
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220906164212.84835-1-linux@fw-web.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

add support for user LEDs on Radxa ROCK 4C+ board.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220908031726.1307105-2-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

only user_led2 (blue) is supported.

user_led1 (green) is not connected to any gpio so it cannot be
controlled.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220908031726.1307105-1-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the new rk817 charger driver to the Odroid Go Advance. Create a
monitored battery node as well for the charger to use. All values
from monitored battery are gathered from the BSP kernel for the
Odroid Go Advance provided by HardKernel.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20220827021623.23829-5-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Merge tag 'amlogic-arm64-dt-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt

Amlogic ARM64 DT changes for v6.1:
- add Bindings & DT for Beelink GT1 Ultimate
- Remove invalid 'enable-active-low' on SM1 & G12A boards
- add Bindings & DT for the new JetHub D1p

* tag 'amlogic-arm64-dt-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
  arm64: dts: meson: add support for Beelink GT1 Ultimate
  dt-bindings: arm: amlogic: add Beelink GT1 Ultimate binding
  arm64: dts: meson-sm1-sei610: Remove 'enable-active-low'
  arm64: dts: meson-g12a: Remove 'enable-active-low'
  dt-bindings: arm: amlogic: add bindings for Jethub D1p (j110)
  arm64: dts: meson-axg: add support for JetHub D1p (j110)

Link: https://lore.kernel.org/r/d0079686-40ae-58b2-e58b-c8dc6361d7f0@baylibre.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Voltage constraints on vccio_sd are invalid. They don't match the voltages
that LDO9 can generate, and this causes rk808-regulator driver to fail
to probe with -EINVAL when it tries to apply the constraints during boot.

Fix the constraints to something that LDO9 can be actually configured for.

Fixes: 78a21c7d ("arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Tested-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Link: https://lore.kernel.org/r/20220904233652.3197885-1-megi@xff.czSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for Radxa ROCK 4C+ SBC.

Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec

Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220902065057.97425-3-jagan@amarulasolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>