- 16 Jan, 2015 8 commits
-
-
Takashi Iwai authored
commit c507de88 upstream. stac_store_hints() does utterly wrong for masking the values for gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately, this feature is used very rarely, so the impact must be really small. Reported-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Felipe Balbi authored
commit 7ce67a38 upstream. The CPSW IP implements pulse-signaled interrupts. Due to that we must write a correct, pre-defined value to the CPDMA_MACEOIVECTOR register so the controller generates a pulse on the correct IRQ line to signal the End Of Interrupt. The way the driver is written today, all four IRQ lines are requested using the same IRQ handler and, because of that, we could fall into situations where a TX IRQ fires but we tell the controller that we ended an RX IRQ (or vice-versa). This situation triggers an IRQ storm on the reserved IRQ 127 of INTC which will in turn call ack_bad_irq() which will, then, print a ton of: unexpected IRQ trap at vector 00 In order to fix the problem, we are moving all calls to cpdma_ctlr_eoi() inside the IRQ handler and making sure we *always* write the correct value to the CPDMA_MACEOIVECTOR register. Note that the algorithm assumes that IRQ numbers and value-to-be-written-to-EOI are proportional, meaning that a write of value 0 would trigger an EOI pulse for the RX_THRESHOLD Interrupt and that's the IRQ number sitting in the 0-th index of our irqs_table array. This, however, is safe at least for current implementations of CPSW so we will refrain from making the check smarter (and, as a side-effect, slower) until we actually have a platform where IRQ lines are swapped. This patch has been tested for several days with AM335x- and AM437x-based platforms. AM57x was left out because there are still pending patches to enable ethernet in mainline for that platform. A read of the TRM confirms the statement on previous paragraph. Reported-by:
Yegor Yefremov <yegorslists@googlemail.com> Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly) Signed-off-by:
Felipe Balbi <balbi@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Chris Mason authored
commit 6f896054 upstream. Commit 1d52c78a (Btrfs: try not to ENOSPC on log replay) added a check to skip delayed inode updates during log replay because it confuses the enospc code. But the delayed processing will end up ignoring delayed refs from log replay because the inode itself wasn't put through the delayed code. This can end up triggering a warning at commit time: WARNING: CPU: 2 PID: 778 at fs/btrfs/delayed-inode.c:1410 btrfs_assert_delayed_root_empty+0x32/0x34() Which is repeated for each commit because we never process the delayed inode ref update. The fix used here is to change btrfs_delayed_delete_inode_ref to return an error if we're currently in log replay. The caller will do the ref deletion immediately and everything will work properly. Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Alan Stern authored
commit 511833ac upstream. Commit ac61d195 (scsi: set correct completion code in scsi_send_eh_cmnd()) introduced a bug. It changed the stored return value from a queuecommand call, but it didn't take into account that the return value was used again later on. This patch fixes the bug by changing the later usage. There is a big comment in the middle of scsi_send_eh_cmnd() which does a good job of explaining how the routine works. But it mentions a "rtn = FAILURE" value that doesn't exist in the code. This patch adjusts the code to match the comment (I assume the comment is right and the code is wrong). This fixes Bugzilla #88341. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Андрей Аладьев <aladjev.andrew@gmail.com> Tested-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Steev Klimaszewski authored
commit 007487f1 upstream. Currently we enable Exynos devices in the multi v7 defconfig, however, when testing on my ODROID-U3, I noticed that USB was not working. Enabling this option causes USB to work, which enables networking support as well since the ODROID-U3 has networking on the USB bus. [arnd] Support for odroid-u3 was added in 3.10, so it would be nice to backport this fix at least that far. Signed-off-by:
Steev Klimaszewski <steev@gentoo.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Tomi Valkeinen authored
commit 30ea9c52 upstream. fb_deferred_io_fsync() returns the value of schedule_delayed_work() as an error code, but schedule_delayed_work() does not return an error. It returns true/false depending on whether the work was already queued. Fix this by ignoring the return value of schedule_delayed_work(). Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Tomi Valkeinen authored
commit 92b004d1 upstream. If the probe of an fb driver has been deferred due to missing dependencies, and the probe is later ran when a module is loaded, the fbdev framework will try to find a logo to use. However, the logos are __initdata, and have already been freed. This causes sometimes page faults, if the logo memory is not mapped, sometimes other random crashes as the logo data is invalid, and sometimes nothing, if the fbdev decides to reject the logo (e.g. the random value depicting the logo's height is too big). This patch adds a late_initcall function to mark the logos as freed. In reality the logos are freed later, and fbdev probe may be ran between this late_initcall and the freeing of the logos. In that case we will miss drawing the logo, even if it would be possible. Signed-off-by:
-
Andy Lutomirski authored
commit 1ddf0b1b upstream. In Linux 3.18 and below, GCC hoists the lsl instructions in the pvclock code all the way to the beginning of __vdso_clock_gettime, slowing the non-paravirt case significantly. For unknown reasons, presumably related to the removal of a branch, the performance issue is gone as of e76b027e x86,vdso: Use LSL unconditionally for vgetcpu but I don't trust GCC enough to expect the problem to stay fixed. There should be no correctness issue, because the __getcpu calls in __vdso_vlock_gettime were never necessary in the first place. Note to stable maintainers: In 3.18 and below, depending on configuration, gcc 4.9.2 generates code like this: 9c3: 44 0f 03 e8 lsl %ax,%r13d 9c7: 45 89 eb mov %r13d,%r11d 9ca: 0f 03 d8 lsl %ax,%ebx This patch won't apply as is to any released kernel, but I'll send a trivial backported version if needed. [ Backported by Andy Lutomirski. Should apply to all affected versions. This fixes a functionality bug as well as a performance bug: buggy kernels can infinite loop in __vdso_clock_gettime on affected compilers. See, for exammple: https://bugzilla.redhat.com/show_bug.cgi?id=1178975 ] Fixes: 51c19b4f x86: vdso: pvclock gettime support Cc: Marcelo Tosatti <mtosatti@redhat.com> Acked-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Andy Lutomirski <luto@amacapital.net> [ luis: backported to 3.16: used Andy's backport for stable kernels ] Signed-off-by:
-
- 15 Jan, 2015 32 commits
-
-
Andrew Jackson authored
commit 3475c3d0 upstream. Flush the FIFOs when the stream is prepared for use. This avoids an inadvertent swapping of the left/right channels if the FIFOs are not empty at startup. Signed-off-by:
Andrew Jackson <Andrew.Jackson@arm.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Ilia Mirkin authored
commit 4761703b upstream. Several users have, over time, reported issues with MSI on these IGPs. They're old, rarely available, and MSI doesn't provide such huge advantages on them. Just disable. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87361 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74492 Fixes: fa8c9ac7 ("drm/nv4c/mc: nv4x igp's have a different msi rearm register") Signed-off-by:
Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Andy Lutomirski authored
commit 394f56fe upstream. The theory behind vdso randomization is that it's mapped at a random offset above the top of the stack. To avoid wasting a page of memory for an extra page table, the vdso isn't supposed to extend past the lowest PMD into which it can fit. Other than that, the address should be a uniformly distributed address that meets all of the alignment requirements. The current algorithm is buggy: the vdso has about a 50% probability of being at the very end of a PMD. The current algorithm also has a decent chance of failing outright due to incorrect handling of the case where the top of the stack is near the top of its PMD. This fixes the implementation. The paxtest estimate of vdso "randomisation" improves from 11 bits to 18 bits. (Disclaimer: I don't know what the paxtest code is actually calculating.) It's worth noting that this algorithm is inherently biased: the vdso is more likely to end up near the end of its PMD than near the beginning. Ideally we would either nix the PMD sharing requirement or jointly randomize the vdso and the stack to reduce the bias. In the mean time, this is a considerable improvement with basically no risk of compatibility issues, since the allowed outputs of the algorithm are unchanged. As an easy test, doing this: for i in `seq 10000` do grep -P vdso /proc/self/maps |cut -d- -f1 done |sort |uniq -d used to produce lots of output (1445 lines on my most recent run). A tiny subset looks like this: 7fffdfffe000 7fffe01fe000 7fffe05fe000 7fffe07fe000 7fffe09fe000 7fffe0bfe000 7fffe0dfe000 Note the suspicious fe000 endings. With the fix, I get a much more palatable 76 repeated addresses. Reviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Ville Syrjälä authored
commit 7d47559e upstream. The flip stall detector kicks in when pending>=INTEL_FLIP_COMPLETE. That means if we first call intel_prepare_page_flip() but don't call intel_finish_page_flip(), the next stall check will erroneosly think the page flip was somehow stuck. With enough debug spew emitted from the interrupt handler my 830 hangs when this happens. My theory is that the previous vblank interrupt gets sufficiently delayed that the handler will see the pending bit set in IIR, but ISR still has the bit set as well (ie. the flip was processed by CS but didn't complete yet). In this case the handler will proceed to call intel_check_page_flip() immediately after intel_prepare_page_flip(). It then tries to print a backtrace for the stuck flip WARN, which apparetly results in way too much debug spew delaying interrupt processing further. That then seems to cause an endless loop in the interrupt handler, and the machine is dead until the watchdog kicks in and reboots. At least limiting the number of iterations of the loop in the interrupt handler also prevented the hang. So it seems better to not call intel_prepare_page_flip() without immediately calling intel_finish_page_flip(). The IIR/ISR trickery avoids races here so this is a perfectly safe thing to do. v2: Fix typo in commit message (checkpatch) Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88381 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85888Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Hisashi Nakamura authored
commit 01576056 upstream. SH-MSIOF driver is enabled autosuspend API of spi framework. But autosuspend framework doesn't work during initializing. So runtime PM lock is added in SH-MSIOF driver initializing. Fixes: e2a0ba54 (spi: sh-msiof: Convert to spi core auto_runtime_pm framework) Signed-off-by:
Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by:
Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by:
-
Luis Henriques authored
Signed-off-by: -
Sasha Levin authored
commit a3a87844 upstream. When a key is being garbage collected, it's key->user would get put before the ->destroy() callback is called, where the key is removed from it's respective tracking structures. This leaves a key hanging in a semi-invalid state which leaves a window open for a different task to try an access key->user. An example is find_keyring_by_name() which would dereference key->user for a key that is in the process of being garbage collected (where key->user was freed but ->destroy() wasn't called yet - so it's still present in the linked list). This would cause either a panic, or corrupt memory. Fixes CVE-2014-9529. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
David Howells <dhowells@redhat.com> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by:
-
Al Viro authored
commit ca5358ef upstream. ... by not hitting rename_retry for reasons other than rename having happened. In other words, do _not_ restart when finding that between unlocking the child and locking the parent the former got into __dentry_kill(). Skip the killed siblings instead... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by:
-
Al Viro authored
commit 946e51f2 upstream. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by:
-
Sven Eckelmann authored
commit 5b6698b0 upstream. The fragmentation code was replaced in 610bfc6b ("batman-adv: Receive fragmented packets and merge"). The new code provided a mostly unused parameter skb for the merging function. It is used inside the function to calculate the additionally needed skb tailroom. But instead of increasing its own tailroom, it is only increasing the tailroom of the first queued skb. This is not correct in some situations because the first queued entry can be a different one than the parameter. An observed problem was: 1. packet with size 104, total_size 1464, fragno 1 was received - packet is queued 2. packet with size 1400, total_size 1464, fragno 0 was received - packet is queued at the end of the list 3. enough data was received and can be given to the merge function (1464 == (1400 - 20) + (104 - 20)) - merge functions gets 1400 byte large packet as skb argument 4. merge function gets first entry in queue (104 byte) - stored as skb_out 5. merge function calculates the required extra tail as total_size - skb->len - pskb_expand_head tail of skb_out with 64 bytes 6. merge function tries to squeeze the extra 1380 bytes from the second queued skb (1400 byte aka skb parameter) in the 64 extra tail bytes of skb_out Instead calculate the extra required tail bytes for skb_out also using skb_out instead of using the parameter skb. The skb parameter is only used to get the total_size from the last received packet. This is also the total_size used to decide that all fragments were received. Reported-by:
Philipp Psurek <philipp.psurek@gmail.com> Signed-off-by:
Sven Eckelmann <sven@narfation.org> Acked-by:
Martin Hundebøll <martin@hundeboll.net> Signed-off-by:
-
Michael Mullin authored
commit b90b3c4a upstream. Add support for the acer c720p touchscreen. Tested manually by using the touchscreen on the acer c720p-2664 Based on the following patch by Dave Parker <dparker@chromium.org>: https://chromium-review.googlesource.com/#/c/167136/Signed-off-by:
Michael Mullin <masmullin@gmail.com> Reviewed-by:
Benson Leung <bleung@chromium.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Cc: Scot Doyle <lkml14@scotdoyle.com> Signed-off-by:
-
Gene Chen authored
commit 963cb6fa upstream. Add support for Leon touch devices, which is the same as falco/peppy/wolf on the same buses using the LynxPoint-LP I2C via the i2c-designware-pci driver. Based on these patches from the chromeos-3.8 kernel: https://chromium-review.googlesource.com/168351 https://chromium-review.googlesource.com/173445Signed-off-by:
Gene Chen <gene.chen@intel.com> Signed-off-by:
Scot Doyle <lkml14@scotdoyle.com> Reviewed-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Mohammed Habibulla authored
commit 0e1e5e59 upstream. Add support for Dell Chromebook 11's touch device, which is the same as falco/peppy on the same bus using the LynxPoint-LP I2C via the i2c-designware-pci driver. Based on these patches from the chromeos-3.8 kernel: https://chromium-review.googlesource.com/#/c/65320/ https://chromium-review.googlesource.com/#/c/174664/Signed-off-by:
Mohammed Habibulla <moch@chromium.org> Signed-off-by:
-
Benson Leung authored
commit 5ea9567f upstream. Add support for the trackpad on HP Chromebook 14. Signed-off-by:
-
Mika Westerberg authored
commit da3b0ab7 upstream. Acer C720 has touchpad and light sensor connected to a separate I2C buses. Since the designware I2C host controller driver has two instances on this particular machine we need a way to match the correct instance. Add support for this and then register both C720 touchpad and light sensor. This code is based on following patch from Benson Leung: https://patchwork.kernel.org/patch/3074411/Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
-
Jan Kara authored
commit e237ec37 upstream. Check that length specified in a component of a symlink fits in the input buffer we are reading. Also properly ignore component length for component types that do not use it. Otherwise we read memory after end of buffer for corrupted udf image. Reported-by:
Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Jan Kara authored
commit a1d47b26 upstream. UDF specification allows arbitrarily large symlinks. However we support only symlinks at most one block large. Check the length of the symlink so that we don't access memory beyond end of the symlink block. Reported-by:
Carl Henrik Lunde <chlunde@gmail.com> Signed-off-by:
-
Jan Kara authored
commit e159332b upstream. Verify that inode size is sane when loading inode with data stored in ICB. Otherwise we may get confused later when working with the inode and inode size is too big. Reported-by:
-
Jan Kara authored
commit 0e5cc9a4 upstream. Symlink reading code does not check whether the resulting path fits into the page provided by the generic code. This isn't as easy as just checking the symlink size because of various encoding conversions we perform on path. So we have to check whether there is still enough space in the buffer on the fly. Reported-by:
-
Rabin Vincent authored
commit 7e77bdeb upstream. If a request is backlogged, it's complete() handler will get called twice: once with -EINPROGRESS, and once with the final error code. af_alg's complete handler, unlike other users, does not handle the -EINPROGRESS but instead always completes the completion that recvmsg() is waiting on. This can lead to a return to user space while the request is still pending in the driver. If userspace closes the sockets before the requests are handled by the driver, this will lead to use-after-frees (and potential crashes) in the kernel due to the tfm having been freed. The crashes can be easily reproduced (for example) by reducing the max queue length in cryptod.c and running the following (from http://www.chronox.de/libkcapi.html) on AES-NI capable hardware: $ while true; do kcapi -x 1 -e -c '__ecb-aes-aesni' \ -k 00000000000000000000000000000000 \ -p 00000000000000000000000000000000 >/dev/null & done Signed-off-by:
Rabin Vincent <rabin.vincent@axis.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Jan Kara authored
commit 4e202462 upstream. We didn't check length of rock ridge ER records before printing them. Thus corrupted isofs image can cause us to access and print some memory behind the buffer with obvious consequences. Reported-and-tested-by:
-
Johannes Berg authored
commit d6ca18de upstream. With a significant number of deployed APs, enabling uAPSD leads to the AP never using aggregation sessions (likely due to the complexities involved in handling uAPSD in those.) This obviously results in a large drop in throughput with such APs. On the other hand, uAPSD can result in some power consumption benefits, but for now just disable it to get performance with affected APs back up. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Jason Baron authored
commit 64c7569c upstream. I've confirmed that monitoring the package power usage as well as setting power limits appear to be working as expected. Supports the package and dram domains. Tested aginst cpu: Intel(R) Xeon(R) CPU E5-2650 v3 @ 2.30GHz Signed-off-by:
Jason Baron <jbaron@akamai.com> Acked-by:
Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
-
Liu Bo authored
commit 25ce459c upstream. One of my tests shows that when we really don't have space to reclaim via flush_space and also run out of space, this async reclaim work loops on adding itself into the workqueue and keeps writing something to disk according to iostat's results, and these writes mainly comes from commit_transaction which writes super_block. This's unacceptable as it can be bad to disks, especially memeory storages. This adds a check to avoid the above situation. Signed-off-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
-
Paolo Bonzini authored
commit a629df7e upstream. Since most virtual machines raise this message once, it is a bit annoying. Make it KERN_DEBUG severity. Fixes: 7a2e8aafSigned-off-by:
-
John David Anglin authored
commit 45db0738 upstream. The __ldcw macro has a problem when its argument needs to be reloaded from memory. The output memory operand and the input register operand both need to be reloaded using a register in class R1_REGS when generating 64-bit code. This fails because there's only a single register in the class. Instead, use a memory clobber. This also makes the __ldcw macro a compiler memory barrier. Signed-off-by:
John David Anglin <dave.anglin@bell.net> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Richard Guy Briggs authored
commit 041d7b98 upstream. A regression was caused by commit 780a7654: audit: Make testing for a valid loginuid explicit. (which in turn attempted to fix a regression caused by e1760bd5) When audit_krule_to_data() fills in the rules to get a listing, there was a missing clause to convert back from AUDIT_LOGINUID_SET to AUDIT_LOGINUID. This broke userspace by not returning the same information that was sent and expected. The rule: auditctl -a exit,never -F auid=-1 gives: auditctl -l LIST_RULES: exit,never f24=0 syscall=all when it should give: LIST_RULES: exit,never auid=-1 (0xffffffff) syscall=all Tag it so that it is reported the same way it was set. Create a new private flags audit_krule field (pflags) to store it that won't interact with the public one from the API. Signed-off-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <pmoore@redhat.com> Signed-off-by:
-
Lorenzo Pieralisi authored
commit f43c2718 upstream. On arm64 the TTBR0_EL1 register is set to either the reserved TTBR0 page tables on boot or to the active_mm mappings belonging to user space processes, it must never be set to swapper_pg_dir page tables mappings. When a CPU is booted its active_mm is set to init_mm even though its TTBR0_EL1 points at the reserved TTBR0 page mappings. This implies that when __cpu_suspend is triggered the active_mm can point at init_mm even if the current TTBR0_EL1 register contains the reserved TTBR0_EL1 mappings. Therefore, the mm save and restore executed in __cpu_suspend might turn out to be erroneous in that, if the current->active_mm corresponds to init_mm, on resume from low power it ends up restoring in the TTBR0_EL1 the init_mm mappings that are global and can cause speculation of TLB entries which end up being propagated to user space. This patch fixes the issue by checking the active_mm pointer before restoring the TTBR0 mappings. If the current active_mm == &init_mm, the code sets the TTBR0_EL1 to the reserved TTBR0 mapping instead of switching back to the active_mm, which is the expected behaviour corresponding to the TTBR0_EL1 settings when __cpu_suspend was entered. Fixes: 95322526 ("arm64: kernel: cpu_{suspend/resume} implementation") Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Laura Abbott authored
commit c3684fbb upstream. The function cpu_resume currently lives in the .data section. There's no reason for it to be there since we can use relative instructions without a problem. Move a few cpu_resume data structures out of the assembly file so the .data annotation can be dropped completely and cpu_resume ends up in the read only text section. Reviewed-by:
Mark Rutland <mark.rutland@arm.com> Reviewed-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Laura Abbott <lauraa@codeaurora.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> [ luis: 3.16-stable prereq for f43c2718 "arm64: kernel: fix __cpu_suspend mm switch on warm-boot" ] Signed-off-by:
-
Lorenzo Pieralisi authored
commit 714f5992 upstream. CPU suspend is the standard kernel interface to be used to enter low-power states on ARM64 systems. Current cpu_suspend implementation by default assumes that all low power states are losing the CPU context, so the CPU registers must be saved and cleaned to DRAM upon state entry. Furthermore, the current cpu_suspend() implementation assumes that if the CPU suspend back-end method returns when called, this has to be considered an error regardless of the return code (which can be successful) since the CPU was not expected to return from a code path that is different from cpu_resume code path - eg returning from the reset vector. All in all this means that the current API does not cope well with low-power states that preserve the CPU context when entered (ie retention states), since first of all the context is saved for nothing on state entry for those states and a successful state entry can return as a normal function return, which is considered an error by the current CPU suspend implementation. This patch refactors the cpu_suspend() API so that it can be split in two separate functionalities. The arm64 cpu_suspend API just provides a wrapper around CPU suspend operation hook. A new function is introduced (for architecture code use only) for states that require context saving upon entry: __cpu_suspend(unsigned long arg, int (*fn)(unsigned long)) __cpu_suspend() saves the context on function entry and calls the so called suspend finisher (ie fn) to complete the suspend operation. The finisher is not expected to return, unless it fails in which case the error is propagated back to the __cpu_suspend caller. The API refactoring results in the following pseudo code call sequence for a suspending CPU, when triggered from a kernel subsystem: /* * int cpu_suspend(unsigned long idx) * @idx: idle state index */ { -> cpu_suspend(idx) |---> CPU operations suspend hook called, if present |--> if (retention_state) |--> direct suspend back-end call (eg PSCI suspend) else |--> __cpu_suspend(idx, &back_end_finisher); } By refactoring the cpu_suspend API this way, the CPU operations back-end has a chance to detect whether idle states require state saving or not and can call the required suspend operations accordingly either through simple function call or indirectly through __cpu_suspend() which carries out state saving and suspend finisher dispatching to complete idle state entry. Reviewed-by:
Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by:
-
Lorenzo Pieralisi authored
commit 18ab7db6 upstream. Suspend init function must be marked as __init, since it is not needed after the kernel has booted. This patch moves the cpu_suspend_init() function to the __init section. Signed-off-by:
-
Richard Guy Briggs authored
commit 54dc77d9 upstream. Eric Paris explains: Since kauditd_send_multicast_skb() gets called in audit_log_end(), which can come from any context (aka even a sleeping context) GFP_KERNEL can't be used. Since the audit_buffer knows what context it should use, pass that down and use that. See: https://lkml.org/lkml/2014/12/16/542 BUG: sleeping function called from invalid context at mm/slab.c:2849 in_atomic(): 1, irqs_disabled(): 0, pid: 885, name: sulogin 2 locks held by sulogin/885: #0: (&sig->cred_guard_mutex){+.+.+.}, at: [<ffffffff91152e30>] prepare_bprm_creds+0x28/0x8b #1: (tty_files_lock){+.+.+.}, at: [<ffffffff9123e787>] selinux_bprm_committing_creds+0x55/0x22b CPU: 1 PID: 885 Comm: sulogin Not tainted 3.18.0-next-20141216 #30 Hardware name: Dell Inc. Latitude E6530/07Y85M, BIOS A15 06/20/2014 ffff880223744f10 ffff88022410f9b8 ffffffff916ba529 0000000000000375 ffff880223744f10 ffff88022410f9e8 ffffffff91063185 0000000000000006 0000000000000000 0000000000000000 0000000000000000 ffff88022410fa38 Call Trace: [<ffffffff916ba529>] dump_stack+0x50/0xa8 [<ffffffff91063185>] ___might_sleep+0x1b6/0x1be [<ffffffff910632a6>] __might_sleep+0x119/0x128 [<ffffffff91140720>] cache_alloc_debugcheck_before.isra.45+0x1d/0x1f [<ffffffff91141d81>] kmem_cache_alloc+0x43/0x1c9 [<ffffffff914e148d>] __alloc_skb+0x42/0x1a3 [<ffffffff914e2b62>] skb_copy+0x3e/0xa3 [<ffffffff910c263e>] audit_log_end+0x83/0x100 [<ffffffff9123b8d3>] ? avc_audit_pre_callback+0x103/0x103 [<ffffffff91252a73>] common_lsm_audit+0x441/0x450 [<ffffffff9123c163>] slow_avc_audit+0x63/0x67 [<ffffffff9123c42c>] avc_has_perm+0xca/0xe3 [<ffffffff9123dc2d>] inode_has_perm+0x5a/0x65 [<ffffffff9123e7ca>] selinux_bprm_committing_creds+0x98/0x22b [<ffffffff91239e64>] security_bprm_committing_creds+0xe/0x10 [<ffffffff911515e6>] install_exec_creds+0xe/0x79 [<ffffffff911974cf>] load_elf_binary+0xe36/0x10d7 [<ffffffff9115198e>] search_binary_handler+0x81/0x18c [<ffffffff91153376>] do_execveat_common.isra.31+0x4e3/0x7b7 [<ffffffff91153669>] do_execve+0x1f/0x21 [<ffffffff91153967>] SyS_execve+0x25/0x29 [<ffffffff916c61a9>] stub_execve+0x69/0xa0 Reported-by:
Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Signed-off-by:
-
