My recent hack to allocate the hash table under 1GB on cell was poorly
tested, *cough*. It turns out on blades with large amounts of memory we
fail to allocate the hash table at all. This is because RTAS has been
instantiated just below 768MB, and 0-x MB are used by the kernel,
leaving no areas that are both large enough and also naturally-aligned.

For the cell IOMMU hack the page tables must be under 2GB, so use that
as the limit instead. This has been tested on real hardware and boots
happily.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Once again, this time with feeling....

						- Ted

>From c91cfaabc17f8a53807a2f31f067a732e34a1550 Mon Sep 17 00:00:00 2001
From: Theodore Ts'o <tytso@mit.edu>
Date: Wed, 12 Mar 2008 11:50:39 -0400
Subject: Export empty_zero_page

The empty_zero_page symbol is exported by most other architectures
(s390, ia64, x86, um), and an upcoming ext4 patch needs it because
ZERO_PAGE() references empty_zero_page, and we need it to zero out an
unitialized extents in ext4 files.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The iSeries viodasd drivers does some very strange things with
scatterlists, one of these causing a BUG_ON to trigger when
scatterlist debugging is enabled due to initializing the
scatterlist with memset instead of sg_init_table().

This fixes it by using sg_init_table().  The rest of the stuff
it does to that poor list is still pretty awful but it will work.

I may look into fixing things in a nicer way some other time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When building arch/powerpc/platforms/powermac/pic.c when !CONFIG_ADB_PMU
we get the following warnings:

arch/powerpc/platforms/powermac/pic.c: In function 'pmacpic_find_viaint':
arch/powerpc/platforms/powermac/pic.c:623: warning: label 'not_found' defined but not used

This fixes it.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When building drivers/macintosh/mediabay.c if CONFIG_ADB_PMU isn't
defined we get:

drivers/built-in.o: In function `media_bay_step':
mediabay.c:(.text+0x92b84): undefined reference to `pmu_suspend'
mediabay.c:(.text+0x92c08): undefined reference to `pmu_resume'

Create empty place holders in that scenario.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

pmu_sys_suspended is declared extern when:
	defined(CONFIG_PM_SLEEP) && defined(CONFIG_PPC32)
but only defined when:
	defined(CONFIG_SUSPEND) && defined(CONFIG_PPC32)
which is wrong.  Let's fix that.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Currently, if drivers/macintosh/apm_emu is a module and the config
doesn't have CONFIG_SUSPEND we get:

ERROR: "pmu_batteries" [drivers/macintosh/apm_emu.ko] undefined!
ERROR: "pmu_battery_count" [drivers/macintosh/apm_emu.ko] undefined!
ERROR: "pmu_power_flags" [drivers/macintosh/apm_emu.ko] undefined!

on PPC32.  The variables aren't wrapped in '#if defined(CONFIG_SUSPEND)'
so we probably shouldn't wrap the exports either.  This removes the
CONFIG_SUSPEND part of the export, which fixes compilation on ppc32.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The PMU backlight code would kick in during sleep/resume even on
machines that use a different backlight method.  This breaks
sleep on some PowerBooks.

This fixes it by adding a flag to indicate whether the backlight
is controlled by the PMU, and testing that before trying to use
the PMU to turn off the backlight during sleep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

A bogus test for unassigned resources that came from our 32-bit
PCI code ended up being "merged" by my previous patch series,
breaking some 64-bit setups where devices have legal resources
ending at 0xffffffff.

This fixes it by completely changing the test.  We now test for
res->start == 0, as the generic code expects, and we also only
do so on platforms that don't have the PPC_PCI_PROBE_ONLY flag
set, as there are cases of pSeries and iSeries where it could
be a valid value and those can't reassign devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The pattern substitution rules were failing when used with zImage-dtb
targets.  If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.

This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Some drivers (such as V4L2) have code that causes gcc to generate
calls to __ucmpdi2 when compiling for 32-bit powerpc, which results
in either a link-time error or a module that can't be loaded, as
we don't currently have a __ucmpdi2.  This adds one so these drivers
can be used.
Signed-off-by: Paul Mackerras <paulus@samba.org>

At present, we can hit the BUG_ON in __spu_update_sched_info by reading
the regs file of a context between two calls to spu_run. The
spu_release_saved called by spufs_regs_read() is resulting in the (now
non-runnable) context being placed back on the run queue, so the next
call to spu_run ends up in the bug condition.

This change uses the SPU_SCHED_SPU_RUN flag to only reschedule a context
if it's still in spu_run().
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

commit 4ef11014 introduced a usage of SCHED_IDLE to detect when
a context is within spu_run.

Instead of SCHED_IDLE (which has other meaning), add a flag to
sched_flags to tell if a context should be running.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

The function was returning NULL the second time it was
called if the firmware was uploaded from the boot loader
or the first time it was called if the firmware was
uploaded from the kernel.
Signed-off-by: Ionut Nicu <ionut.nicu@freescale.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Not all e300 cores support the performance monitors, and the ones
that don't will be confused by the mf/mtpmr instructions.  This
allows the support to be optional, so the 8349 can turn it off
while the 8379 can turn it on.  Sadly, those aren't config options,
so it will be left to the defconfigs and the users to make that
determination.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This makes swap routines operate correctly on the ppc_8xx based machines.

Recent kernel's size makes swap feature very important on low-memory platfor
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The following patch allows interrupts to occur on the
sbc8548. Currently PCI and PCI-X devices get assigned an IRQ
but the interrupt count never increases.  This solves the
problem and adds PCI support as well.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html

Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This makes swap routines operate correctly on the ppc_8xx based machines.
Code has been revalidated on mpc885ads (8M sdram) with recent kernel. Based
on patch from Yuri Tikhonov <yur@emcraft.com> to do the same on arch/ppc
instance.

Recent kernel's size makes swap feature very important on low-memory platforms,
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces.  The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
  sh: Fix up the sh64 build.
  sh: Fix up SH7710 VoIP-GW build.
  sh: Flag PMB support as EXPERIMENTAL.
  sh: Update r7780mp defconfig.
  fb: hitfb: Balance probe/remove section annotations.
  sh: hp6xx: Fix up hp6xx_apm build failure.
  fb: pvr2fb: Fix up remaining section mismatch.
  sh: Fix up section mismatches.
  sh: hp6xx: Correct APM output.
  sh: update se7780 defconfig
  sh: replace remaining __FUNCTION__ occurrences
  sh: export copy-page() to modules
  sh_ksyms_32.c update for gcc 4.3
  sh/mm/pg-sh7705.c must #include <linux/fs.h>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
  [Blackfin] arch: current_l1_stack_save is a pointer, so use NULL rather than 0
  [Blackfin] arch: fix atomic and32/xor32 comments and ENDPROC markings
  [Blackfin] arch: fix bug - allow SDH driver to be used as module
  [Blackfin] arch: to kill syscalls missing warning by adding new timerfd syscalls

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] kprobes arch consolidation build fix
  [IA64] update efi region debugging to use MB, GB and TB as well as KB
  [IA64] use dev_printk in video quirk
  [IA64] remove remaining __FUNCTION__ occurrences
  [IA64] remove unnecessary nfs includes from sys_ia32.c
  [IA64] remove CONFIG_SMP ifdef in ia64_send_ipi()
  [IA64] arch_ptrace() cleanup
  [IA64] remove duplicate code from arch_ptrace()
  [IA64] convert sys_ptrace to arch_ptrace
  [IA64] remove find_thread_for_addr()
  [IA64] do not sync RBS when changing PT_AR_BSP or PT_CFM
  [IA64] access user RBS directly

ia64 named their handler kprobes_fault_handler while all other
arches used kprobe_fault_handler.  Change the function definition
and header declaration.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

When EFI_DEBUG is defined to a non-zero value in arch/ia64/kernel/efi.c,
the efi memory regions are displayed. This patch enhances the
display code in a few ways:

1. Use TB, GB and MB as well as KB as units.
   Although this introduces rounding errors (KB doesn't as
   size is always a multiple of 4Kb), it does make
   things a lot more readable.

   Also as the range is also shown, it is possible to note the exact size
   if it is important. In my experience, the size field is mostly useful
   for getting a general idea of the size of a region.

   On the rx2620 that I use, there actually is an 8TB region (though not
   backed by physical memory, and 8TB really is a lot more readable than
   8589934592KB.

2. pad the size field with leading spaces to further improve readability

   ...
   ... (   8MB)
   ... ( 928MB)
   ... (   3MB)
   ...

   vs

   ...
   ... (8MB)
   ... (928MB)
   ... (3MB)
   ...

3. Pad the attr field out to 64bits using leading zeros,
   to further improve readability.

   ...
   mem05: type= 2, attr=0x0000000000000008, range=[0x0000000004000000-0x000000000481f000) (   8MB)
   mem06: type= 7, attr=0x0000000000000008, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
   mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) (   3MB)
   mem08: type= 4, attr=0x0000000000000008, range=[0x000000003eb8e000-0x000000003ee7a000) (   2MB)
   ...

   ...
   mem05: type= 2, attr=0x8, range=[0x0000000004000000-0x000000000481f000) (   8MB)
   mem06: type= 7, attr=0x8, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
   mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) (   3MB)
   mem08: type= 4, attr=0x8, range=[0x000000003eb8e000-0x000000003ee7a000) (   2MB)
   ...

4. Use %d instead of %u for the index field, as i is a signed int.

N.B: This code is not compiled unless EFI_DEBUG is non 0.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Convert quirk printks to dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

__FUNCTION__ is gcc-specific, use __func__

Long lines have been kept where they exist, some small spacing changes
have been done.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Compilation of 2.6.25-rc2-mm1 on ia64 generates many warnings.

IA64 support 2 ELF format (IA64 binary and IA32 binary),
thus if 2 elf related header included, cause many warning or error.

about 2 week ago, J. Bruce Fields proposed this problem fixed patch.
(http://marc.info/?l=linux-ia64&m=120329313305695&w=2)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

When !CONFIG_SMP, cpu_physical_id() is ia64_get_lid(), which is
functionally identical to

    (ia64_getreg(_IA64_REG_CR_LID) >> 16) & 0xffff

so there's no need for two versions of this code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] xcbc: Fix crash with IPsec
  [CRYPTO] xts: Use proper alignment
  [CRYPTO] digest: Include internal.h for prototypes
  [CRYPTO] authenc: Add missing Kconfig dependency on BLKCIPHER
  [CRYPTO] skcipher: Move chainiv/seqiv into crypto_blkcipher module

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] fix inode leak in xfs_iget_core()
  [XFS] 977545 977545 977545 977545 977545 977545 xfsaild causing too many

Commit ed7b1889 removed page.h from
include/asm-generic/Kbuild so that it shouldn't get exported.

However, it was redundantly listed in asm-mn10300/Kbuild and
asm-x86/Kbuild too. Remove those as well, so it really stops being
exported on those architectures. Also remove the redundant listing of
ptrace.h and termios.h from mn10300.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When using aes-xcbc-mac for authentication in IPsec, 
the kernel crashes. It seems this algorithm doesn't 
account for the space IPsec may make in scatterlist for authtag.
Thus when crypto_xcbc_digest_update2() gets called,
nbytes may be less than sg[i].length. 
Since nbytes is an unsigned number, it wraps
at the end of the loop allowing us to go back 
into loop and causing crash in memcpy.

I used update function in digest.c to model this fix.
Please let me know if it looks ok.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The XTS blockmode uses a copy of the IV which is saved on the stack
and may or may not be properly aligned. If it is not, it will break
hardware cipher like the geode or padlock.
This patch encrypts the IV in place so we don't have to worry about
alignment.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Tested-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

There's still work that needs to be done here, and this should not be
enabled by default on existing boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>