If udevd is configured to rename interfaces according to persistent
naming rules and if a network interface has phys_port_name in sysfs,
its contents will be appended to the interface name.
However, register_netdev creates device in sysfs and if
devlink_port_register is called after that, there is a timeframe in
which udevd may read an empty phys_port_name value. The consequence is
that the interface will lose this suffix and its name will not be
really persistent.

The solution is to register the port before registering a netdev.

Fixes: c6acd629 ("net/mlx5e: Add support for devlink-port in non-representors mode")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The original condition rejected all egress rules that
are not on tunnel device.
Also, the whole point of this egress reject was to disallow bad
rules because of egdev which doesn't exists today, so remove
this check entirely.

Fixes: 0a7fcb78 ("net/mlx5e: Support inner header rewrite with goto action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Register loopback which is needed for tunnel restoration, is now always
enabled if supported and not just with metadata enabled, check for
that instead.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the following warnings: [-Werror=frame-larger-than=]

In function ‘mlx5_tc_ct_entry_add_rule’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:541:1:
error: the frame size of 1136 bytes is larger than 1024 bytes

In function ‘__mlx5_tc_ct_flow_offload’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:1049:1:
error: the frame size of 1168 bytes is larger than 1024 bytes

Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>

If CONFIG_MLX5_TC_CT isn't enabled, all offloading of eswitch tc rules
fails on parsing ct match, even if there is no ct match.

Return success if there is no ct match, regardless of config.

Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:
 In function mlx5_tc_ct_parse_match:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:699:36: warning:
 variable unnew set but not used [-Wunused-but-set-variable]

Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Restore modify header writes the chain mapping on the packet.
This modify header and action is added on all prios connections,
and gets overwritten with the same value consecutively in prios
of the same chain.

Use the chain's modify header only for the last prio of a given tc
chain.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, if firmware doesn't support fwd and modify, driver fails
initializing eswitch chains while entering switchdev mode.

Instead, on such cases, disable the chains and prio feature (as we can't
restore the chain on miss) and the usage of fwd and modify.

Fixes: 8f1e0b97 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When CONFIG_MLX5_ESWITCH is unset, clang warns:

In file included from drivers/net/ethernet/mellanox/mlx5/core/main.c:58:
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:670:1: warning: unused
function 'esw_add_restore_rule' [-Wunused-function]
esw_add_restore_rule(struct mlx5_eswitch *esw, u32 tag)
^
1 warning generated.

This stub function is missing inline; add it to suppress the warning.

Fixes: 11b717d6 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

XDP-redirect is broken in this driver sfc. XDP_REDIRECT requires
tailroom for skb_shared_info when creating an SKB based on the
redirected xdp_frame (both in cpumap and veth).

The fix requires some initial explaining. The driver uses RX page-split
when possible. It reserves the top 64 bytes in the RX-page for storing
dma_addr (struct efx_rx_page_state). It also have the XDP recommended
headroom of XDP_PACKET_HEADROOM (256 bytes). As it doesn't reserve any
tailroom, it can still fit two standard MTU (1500) frames into one page.

The sizeof struct skb_shared_info in 320 bytes. Thus drivers like ixgbe
and i40e, reduce their XDP headroom to 192 bytes, which allows them to
fit two frames with max 1536 bytes into a 4K page (192+1536+320=2048).

The fix is to reduce this drivers headroom to 128 bytes and add the 320
bytes tailroom. This account for reserved top 64 bytes in the page, and
still fit two frame in a page for normal MTUs.

We must never go below 128 bytes of headroom for XDP, as one cacheline
is for xdp_frame area and next cacheline is reserved for metadata area.

Fixes: eb9a36be ("sfc: perform XDP processing on received packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rearrange the config files for remoteproc and IPA to fix their
interdependencies.

First, have CONFIG_QCOM_Q6V5_MSS select QCOM_Q6V5_IPA_NOTIFY so the
notification code is built regardless of whether IPA needs it.

Next, represent QCOM_IPA as being dependent on QCOM_Q6V5_MSS rather
than setting its value to match QCOM_Q6V5_COMMON (which is selected
by QCOM_Q6V5_MSS).

Drop all dependencies from QCOM_Q6V5_IPA_NOTIFY.  The notification
code will be built whenever QCOM_Q6V5_MSS is set, and it has no other
dependencies.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This path fixes the suspicious RCU usage warning reported by
kernel test robot.

net/kcm/kcmproc.c:#RCU-list_traversed_in_non-reader_section

There is no need to use list_for_each_entry_rcu() in
kcm_stats_seq_show() as the list is always traversed under
knet->mutex held.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove set but not used variables 'sw_comp_cons' and 'hw_comp_cons'
to fix gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:20:
 warning: variable sw_comp_cons set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:6:
 warning: variable hw_comp_cons set but not used [-Wunused-but-set-variable]

After removing 'hw_comp_cons',the memory barrier 'rmb()' and its comments become useless,
so remove them as well.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For a single pedit action, multiple offload entries may be used. Set the
hw_stats_type to all of them.

Fixes: 44f86580 ("sched: act: allow user to specify type of HW stats for a filter")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dejin Zheng says:

====================
net: stmmac: Use readl_poll_timeout() to simplify the code

This patch sets just for replace the open-coded loop to the
readl_poll_timeout() helper macro for simplify the code in
stmmac driver.

v2 -> v3:
	- return whatever error code by readl_poll_timeout() returned.
v1 -> v2:
	- no changed. I am a newbie and sent this patch a month
	  ago (February 6th). So far, I have not received any comments or
	  suggestion. I think it may be lost somewhere in the world, so
	  resend it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The dwmac4_dma_reset() function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The init_systime() function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/crypto/chelsio/chcr_ktls.c: In function chcr_ktls_cpl_set_tcb_rpl:
drivers/crypto/chelsio/chcr_ktls.c:662:11: warning:
 variable status set but not used [-Wunused-but-set-variable]

commit 8a30923e ("cxgb4/chcr: Save tx keys and handle HW response")
involved this unused variable, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Netlink support of extended packet number cipher suites,
allows adding and updating XPN macsec interfaces.

Added support in:
    * Creating interfaces with GCM-AES-XPN-128 and GCM-AES-XPN-256 suites.
    * Setting and getting 64bit packet numbers with of SAs.
    * Setting (only on SA creation) and getting ssci of SAs.
    * Setting salt when installing a SAK.

Added 2 cipher suite identifiers according to 802.1AE-2018 table 14-1:
    * MACSEC_CIPHER_ID_GCM_AES_XPN_128
    * MACSEC_CIPHER_ID_GCM_AES_XPN_256

In addition, added 2 new netlink attribute types:
    * MACSEC_SA_ATTR_SSCI
    * MACSEC_SA_ATTR_SALT

Depends on: macsec: Support XPN frame handling - IEEE 802.1AEbw.
Signed-off-by: Era Mayflower <mayflowerera@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support extended packet number cipher suites (802.1AEbw) frames handling.
This does not include the needed netlink patches.

    * Added xpn boolean field to `struct macsec_secy`.
    * Added ssci field to `struct_macsec_tx_sa` (802.1AE figure 10-5).
    * Added ssci field to `struct_macsec_rx_sa` (802.1AE figure 10-5).
    * Added salt field to `struct macsec_key` (802.1AE 10.7 NOTE 1).
    * Created pn_t type for easy access to lower and upper halves.
    * Created salt_t type for easy access to the "ssci" and "pn" parts.
    * Created `macsec_fill_iv_xpn` function to create IV in XPN mode.
    * Support in PN recovery and preliminary replay check in XPN mode.

In addition, according to IEEE 802.1AEbw figure 10-5, the PN of incoming
frame can be 0 when XPN cipher suite is used, so fixed the function
`macsec_validate_skb` to fail on PN=0 only if XPN is off.
Signed-off-by: Era Mayflower <mayflowerera@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: dsa: improve serdes integration

Depends on "net: mii clause 37 helpers".

Andrew Lunn mentioned that the Serdes PCS found in Marvell DSA switches
does not automatically update the switch MACs with the link parameters.
Currently, the DSA code implements a work-around for this.

This series improves the Serdes integration, making use of the recent
phylink changes to support split MAC/PCS setups.  One noticable
improvement for userspace is that ethtool can now report the link
partner's advertisement.

This repost has no changes compared to the previous posting; however,
the regression Andrew had found which exists even without this patch
set has now been fixed by Andrew and merged into the net-next tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the status of the PHY_DETECT bit to determine whether we need to
force the MAC settings in mac_link_up() and mac_link_down().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port_link_state method is only used by mv88e6xxx_port_setup_mac(),
which is now only called during port setup, rather than also being
called via phylink's mac_config method.

Remove this now unnecessary optimisation, which allows us to remove the
port_link_state methods as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting the speed independently of duplex makes little sense; the two
parameters result from negotiation or fixed setup, and may have inter-
dependencies. Moreover, they are always controlled via the same
register - having them split means we have to read-modify-write this
register twice.

Combine the two operations into a single port_set_speed_duplex()
operation. Not only is this more efficient, it reduces the size of the
code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylink_mac_change() is supposed to be called with a 'false' argument
if the link has gone down since it was last reported up; this is to
ensure that link events along with renegotiation events are always
correctly reported to userspace.

Read the BMSR once when we have an interrupt, and report the link
latched status to phylink via phylink_mac_change().  phylink will deal
automatically with re-reading the link state once it has processed the
link-down event.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which
handle the PCS layer of such links.

- Implement phylink PCS link state reading, so that we can provide
  ethtool with the linkmodes and link speed in the expected manner.
  Note: this will only be called for in-band negotiation, which is
  only supported by the serdes interfaces.
- Implement phylink PCS configuration, so that the in-band AN and
  advertisement can be configured.
- Implement phylink PCS negotiation restart, so that the in-band AN
  can be restarted.
- Implement phylink PCS link up, so that when operating out-of-band,
  the Serdes can be configured for the appropriate fixed speed mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only configure the interface settings in mac_config(), leaving the
speed and duplex settings to mac_link_up to deal with.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SGMII/1000base-X serdes register set is a clause 22 register set
offset at 0x2000 in the PHYXS device. Rather than inventing our own
defintions, use those that already exist, and name the register
MV88E6390_SGMII_BMCR.  Also remove the unused MV88E6390_SGMII_STATUS
definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Issue a warning to the kernel log if phylink_mac_link_state() returns
an error. This should not occur, but let's make it visible.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: mii clause 37 helpers

This is a re-post of two patches that are common to two series that
I've sent in recent weeks; I'm re-posting them separately in the hope
that they can be merged.  No changes from either of the previous
postings.

These patches:

1. convert the existing (unused) mii_lpa_to_ethtool_lpa_x() function
   to a linkmode variant.

2. add a helper for clause 37 advertisements, supporting both the
   1000baseX and defacto 2500baseX variants. Note that ethtool does
   not support half duplex for either of these, and we make no effort
   to do so.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper to convert a linkmode advertisement to a clause 37
advertisement value for 1000base-x and 2500base-x.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a LPA to linkmode decoder for 1000BASE-X protocols; this decoder
only provides the modify semantics similar to other such decoders.
This replaces the unused mii_lpa_to_ethtool_lpa_x() helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16.

Fixes: 0fa81b30 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block")
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
mptcp: simplify mptcp_accept()

Currently we allocate the MPTCP master socket at accept time.

The above makes mptcp_accept() quite complex, and requires checks is several
places for NULL MPTCP master socket.

These series simplify the MPTCP accept implementation, moving the master socket
allocation at syn-ack time, so that we drop unneeded checks with the follow-up
patch.

v1 -> v2:
- rebased on top of 2398e399
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch subflow->conn is always != NULL and
is never changed. We can drop a bunch of now unneeded checks.

v1 -> v2:
 - rebased on top of commit 2398e399 ("mptcp: always
   include dack if possible.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change moves the mptcp socket allocation from mptcp_accept() to
subflow_syn_recv_sock(), so that subflow->conn is now always set
for the non fallback scenario.

It allows cleaning up a bit mptcp_accept() reducing the additional
locking and will allow fourther cleanup in the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify code, which
contains platform_get_resource and devm_ioremap_resource.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Being a non-physical port, the CPU port does not have an ocelot_port
structure, so the ocelot_port_writel call inside the
ocelot_port_set_maxlen() function would access data behind a NULL
pointer.

This is a patch for net-next only, the net tree boots fine, the bug was
introduced during the net -> net-next merge.

Fixes: 1d343579 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Fixes: a8015ded ("net: mscc: ocelot: properly account for VLAN header length when setting MRU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling:
tipc_node_link_down()->
   - tipc_node_write_unlock()->tipc_mon_peer_down()
   - tipc_mon_peer_down()
  just after disabling bearer could be caused kernel oops.

Fix this by adding a sanity check to make sure valid memory
access.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checking and returning 'true' boolean is useless as it will be
returning at end of function
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>