- 17 Jun, 2017 40 commits
-
-
Daniel Vetter authored
[ Upstream commit e6e7b48b ] I was under the misconception that the sysfs dev stuff can be fully set up, and then registered all in one step with device_add. That's true for properties and property groups, but not for parents and child devices. Those must be fully registered before you can register a child. Add a bit of tracking to make sure that asynchronous mst connector hotplugging gets this right. For consistency we rely upon the implicit barriers of the connector->mutex, which is taken anyway, to ensure that at least either the connector or device registration call will work out. Mildly tested since I can't reliably reproduce this on my mst box here. Reported-by:
Dave Hansen <dave.hansen@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Acked-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1484237756-2720-1-git-send-email-daniel.vetter@ffwll.chSigned-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Vetter authored
[ Upstream commit e73ab00e ] If we're unlucky then the registration from a hotplugged connector might race with the final registration step on driver load. And since MST topology discover is asynchronous that's even somewhat likely. v2: Also update the kerneldoc for @registered! v3: Review from Chris: - Improve kerneldoc for late_register/early_unregister callbacks. - Use mutex_destroy. Reviewed-by:
Sean Paul <seanpaul@chromium.org> Reported-by:
-
Hans Verkuil authored
[ Upstream commit f9f96fc1 ] Due to an incorrect condition the last_la used for the initial attempt at claiming a logical address could be wrong. The last_la wasn't converted to a mask when ANDing with type2mask, so that test was broken. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit 827e1579 ] The commit 04ff5a09 ("pinctrl: baytrail: Rectify debounce support") almost fixes the logic of debuonce but missed couple of things, i.e. typo in mask when disabling debounce and lack of enabling it back. This patch addresses above issues. Reported-by:
Jean Delvare <jdelvare@suse.de> Fixes: 04ff5a09 ("pinctrl: baytrail: Rectify debounce support") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Arseny Solokha authored
[ Upstream commit 4af0e5bb ] In spite of switching to paged allocation of Rx buffers, the driver still called dma_unmap_single() in the Rx queues tear-down path. The DMA region unmapping code in free_skb_rx_queue() basically predates the introduction of paged allocation to the driver. While being refactored, it apparently hasn't reflected the change in the DMA API usage by its counterpart gfar_new_page(). As a result, setting an interface to the DOWN state now yields the following: # ip link set eth2 down fsl-gianfar ffe24000.ethernet: DMA-API: device driver frees DMA memory with wrong function [device address=0x000000001ecd0000] [size=40] ------------[ cut here ]------------ WARNING: CPU: 1 PID: 189 at lib/dma-debug.c:1123 check_unmap+0x8e0/0xa28 CPU: 1 PID: 189 Comm: ip Tainted: G O 4.9.5 #1 task: dee73400 task.stack: dede2000 NIP: c02101e8 LR: c02101e8 CTR: c0260d74 REGS: dede3bb0 TRAP: 0700 Tainted: G O (4.9.5) MSR: 00021000 <CE,ME> CR: 28002222 XER: 00000000 GPR00: c02101e8 dede3c60 dee73400 000000b6 dfbd033c dfbd36c4 1f622000 dede2000 GPR08: 00000007 c05b1634 1f622000 00000000 22002484 100a9904 00000000 00000000 GPR16: 00000000 db4c849c 00000002 db4c8480 00000001 df142240 db4c84bc 00000000 GPR24: c0706148 c0700000 00029000 c07552e8 c07323b4 dede3cb8 c07605e0 db535540 NIP [c02101e8] check_unmap+0x8e0/0xa28 LR [c02101e8] check_unmap+0x8e0/0xa28 Call Trace: [dede3c60] [c02101e8] check_unmap+0x8e0/0xa28 (unreliable) [dede3cb0] [c02103b8] debug_dma_unmap_page+0x88/0x9c [dede3d30] [c02dffbc] free_skb_resources+0x2c4/0x404 [dede3d80] [c02e39b4] gfar_close+0x24/0xc8 [dede3da0] [c0361550] __dev_close_many+0xa0/0xf8 [dede3dd0] [c03616f0] __dev_close+0x2c/0x4c [dede3df0] [c036b1b8] __dev_change_flags+0xa0/0x174 [dede3e10] [c036b2ac] dev_change_flags+0x20/0x60 [dede3e30] [c03e130c] devinet_ioctl+0x540/0x824 [dede3e90] [c0347dcc] sock_ioctl+0x134/0x298 [dede3eb0] [c0111814] do_vfs_ioctl+0xac/0x854 [dede3f20] [c0111ffc] SyS_ioctl+0x40/0x74 [dede3f40] [c000f290] ret_from_syscall+0x0/0x3c --- interrupt: c01 at 0xff45da0 LR = 0xff45cd0 Instruction dump: 811d001c 7c66482e 813d0020 9061000c 807f000c 5463103a 7cc6182e 3c60c052 386309ac 90c10008 4cc63182 4826b845 <0fe00000> 4bfffa60 3c80c052 388402c4 ---[ end trace 695ae6d7ac1d0c47 ]--- Mapped at: [<c02e22a8>] gfar_alloc_rx_buffs+0x178/0x248 [<c02e3ef0>] startup_gfar+0x368/0x570 [<c036aeb4>] __dev_open+0xdc/0x150 [<c036b1b8>] __dev_change_flags+0xa0/0x174 [<c036b2ac>] dev_change_flags+0x20/0x60 Even though the issue was discovered in 4.9 kernel, the code in question is identical in the current net and net-next trees. Fixes: 75354148 ("gianfar: Add paged allocation and Rx S/G") Signed-off-by:
Arseny Solokha <asolokha@kb.kras.ru> Acked-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jack Morgenstein authored
[ Upstream commit d585df1c ] Some Hypervisors detach VFs from VMs by instantly causing an FLR event to be generated for a VF. In the mlx4 case, this will cause that VF's comm channel to be disabled before the VM has an opportunity to invoke the VF device's "shutdown" method. The result is that the VF driver on the VM will experience a command timeout during the shutdown process when the Hypervisor does not deliver a command-completion event to the VM. To avoid FW command timeouts on the VM when the driver's shutdown method is invoked, we detect the absence of the VF's comm channel at the very start of the shutdown process. If the comm-channel has already been disabled, we cause all FW commands during the device shutdown process to immediately return success (and thus avoid all command timeouts). Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Ben Skeggs authored
[ Upstream commit 96692b09 ] Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Ben Skeggs authored
[ Upstream commit c966b627 ] Signed-off-by:
-
Dimitris Michailidis authored
[ Upstream commit 90427ef5 ] ip6_make_flowlabel() determines the flow label for IPv6 packets. It's supposed to be passed a flow label, which it returns as is if non-0 and in some other cases, otherwise it calculates a new value. The problem is callers often pass a flowi6.flowlabel, which may also contain traffic class bits. If the traffic class is non-0 ip6_make_flowlabel() mistakes the non-0 it gets as a flow label and returns the whole thing. Thus it can return a 'flow label' longer than 20b and the low 20b of that is typically 0 resulting in packets with 0 label. Moreover, different packets of a flow may be labeled differently. For a TCP flow with ECN non-payload and payload packets get different labels as exemplified by this pair of consecutive packets: (pure ACK) Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2:: 0110 .... = Version: 6 .... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT) .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0) .... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0) .... .... .... 0001 1100 1110 0100 1001 = Flow Label: 0x1ce49 Payload Length: 32 Next Header: TCP (6) (payload) Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2:: 0110 .... = Version: 6 .... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0)) .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0) .... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2) .... .... .... 0000 0000 0000 0000 0000 = Flow Label: 0x00000 Payload Length: 688 Next Header: TCP (6) This patch allows ip6_make_flowlabel() to be passed more than just a flow label and has it extract the part it really wants. This was simpler than modifying the callers. With this patch packets like the above become Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2:: 0110 .... = Version: 6 .... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT) .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0) .... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0) .... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e Payload Length: 32 Next Header: TCP (6) Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2:: 0110 .... = Version: 6 .... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0)) .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0) .... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2) .... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e Payload Length: 688 Next Header: TCP (6) Signed-off-by:
Dimitris Michailidis <dmichail@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
David Howells authored
[ Upstream commit 62deb818 ] Initialise the stores_lock in fscache netfs cookies. Technically, it shouldn't be necessary, since the netfs cookie is an index and stores no data, but initialising it anyway adds insignificant overhead. Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Jeff Layton <jlayton@redhat.com> Acked-by:
Steve Dickson <steved@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
David Howells authored
[ Upstream commit 6bdded59 ] fscache_disable_cookie() needs to clear the outstanding writes on the cookie it's disabling because they cannot be completed after. Without this, fscache_nfs_open_file() gets stuck because it disables the cookie when the file is opened for writing but can't uncache the pages till afterwards - otherwise there's a race between the open routine and anyone who already has it open R/O and is still reading from it. Looking in /proc/pid/stack of the offending process shows: [<ffffffffa0142883>] __fscache_wait_on_page_write+0x82/0x9b [fscache] [<ffffffffa014336e>] __fscache_uncache_all_inode_pages+0x91/0xe1 [fscache] [<ffffffffa01740fa>] nfs_fscache_open_file+0x59/0x9e [nfs] [<ffffffffa01ccf41>] nfs4_file_open+0x17f/0x1b8 [nfsv4] [<ffffffff8117350e>] do_dentry_open+0x16d/0x2b7 [<ffffffff811743ac>] vfs_open+0x5c/0x65 [<ffffffff81184185>] path_openat+0x785/0x8fb [<ffffffff81184343>] do_filp_open+0x48/0x9e [<ffffffff81174710>] do_sys_open+0x13b/0x1cb [<ffffffff811747b9>] SyS_open+0x19/0x1b [<ffffffff81001c44>] do_syscall_64+0x80/0x17a [<ffffffff8165c2da>] return_from_SYSCALL_64+0x0/0x7a [<ffffffffffffffff>] 0xffffffffffffffff Reported-by:
Jianhong Yin <jiyin@redhat.com> Signed-off-by:
-
David Howells authored
[ Upstream commit e26bfebd ] Under some circumstances, an fscache object can become queued such that it fscache_object_work_func() can be called once the object is in the OBJECT_DEAD state. This results in the kernel oopsing when it tries to invoke the handler for the state (which is hard coded to 0x2). The way this comes about is something like the following: (1) The object dispatcher is processing a work state for an object. This is done in workqueue context. (2) An out-of-band event comes in that isn't masked, causing the object to be queued, say EV_KILL. (3) The object dispatcher finishes processing the current work state on that object and then sees there's another event to process, so, without returning to the workqueue core, it processes that event too. It then follows the chain of events that initiates until we reach OBJECT_DEAD without going through a wait state (such as WAIT_FOR_CLEARANCE). At this point, object->events may be 0, object->event_mask will be 0 and oob_event_mask will be 0. (4) The object dispatcher returns to the workqueue processor, and in due course, this sees that the object's work item is still queued and invokes it again. (5) The current state is a work state (OBJECT_DEAD), so the dispatcher jumps to it - resulting in an OOPS. When I'm seeing this, the work state in (1) appears to have been either LOOK_UP_OBJECT or CREATE_OBJECT (object->oob_table is fscache_osm_lookup_oob). The window for (2) is very small: (A) object->event_mask is cleared whilst the event dispatch process is underway - though there's no memory barrier to force this to the top of the function. The window, therefore is from the time the object was selected by the workqueue processor and made requeueable to the time the mask was cleared. (B) fscache_raise_event() will only queue the object if it manages to set the event bit and the corresponding event_mask bit was set. The enqueuement is then deferred slightly whilst we get a ref on the object and get the per-CPU variable for workqueue congestion. This slight deferral slightly increases the probability by allowing extra time for the workqueue to make the item requeueable. Handle this by giving the dead state a processor function and checking the for the dead state address rather than seeing if the processor function is address 0x2. The dead state processor function can then set a flag to indicate that it's occurred and give a warning if it occurs more than once per object. If this race occurs, an oops similar to the following is seen (note the RIP value): BUG: unable to handle kernel NULL pointer dereference at 0000000000000002 IP: [<0000000000000002>] 0x1 PGD 0 Oops: 0010 [#1] SMP Modules linked in: ... CPU: 17 PID: 16077 Comm: kworker/u48:9 Not tainted 3.10.0-327.18.2.el7.x86_64 #1 Hardware name: HP ProLiant DL380 Gen9/ProLiant DL380 Gen9, BIOS P89 12/27/2015 Workqueue: fscache_object fscache_object_work_func [fscache] task: ffff880302b63980 ti: ffff880717544000 task.ti: ffff880717544000 RIP: 0010:[<0000000000000002>] [<0000000000000002>] 0x1 RSP: 0018:ffff880717547df8 EFLAGS: 00010202 RAX: ffffffffa0368640 RBX: ffff880edf7a4480 RCX: dead000000200200 RDX: 0000000000000002 RSI: 00000000ffffffff RDI: ffff880edf7a4480 RBP: ffff880717547e18 R08: 0000000000000000 R09: dfc40a25cb3a4510 R10: dfc40a25cb3a4510 R11: 0000000000000400 R12: 0000000000000000 R13: ffff880edf7a4510 R14: ffff8817f6153400 R15: 0000000000000600 FS: 0000000000000000(0000) GS:ffff88181f420000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000002 CR3: 000000000194a000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffffffffa0363695 ffff880edf7a4510 ffff88093f16f900 ffff8817faa4ec00 ffff880717547e60 ffffffff8109d5db 00000000faa4ec18 0000000000000000 ffff8817faa4ec18 ffff88093f16f930 ffff880302b63980 ffff88093f16f900 Call Trace: [<ffffffffa0363695>] ? fscache_object_work_func+0xa5/0x200 [fscache] [<ffffffff8109d5db>] process_one_work+0x17b/0x470 [<ffffffff8109e4ac>] worker_thread+0x21c/0x400 [<ffffffff8109e290>] ? rescuer_thread+0x400/0x400 [<ffffffff810a5acf>] kthread+0xcf/0xe0 [<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140 [<ffffffff816460d8>] ret_from_fork+0x58/0x90 [<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140 Signed-off-by:
Jeremy McNicoll <jeremymc@redhat.com> Tested-by:
Frank Sorenson <sorenson@redhat.com> Tested-by:
Benjamin Coddington <bcodding@redhat.com> Reviewed-by:
-
Dimitris Michailidis authored
[ Upstream commit 1a2a1444 ] Commit cdba756f ("net: move ndo_features_check() close to ndo_start_xmit()") inadvertently moved the doc comment for .ndo_fix_features instead of .ndo_features_check. Fix the comment ordering. Fixes: cdba756f ("net: move ndo_features_check() close to ndo_start_xmit()") Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 6d9f66ac ] The Generic PHY drivers gets assigned after we checked that the current PHY driver is NULL, so we need to check a few things before we can safely dereference d->driver. This would be causing a NULL deference to occur when a system binds to the Generic PHY driver. Update phy_attach_direct() to do the following: - grab the driver module reference after we have assigned the Generic PHY drivers accordingly, and remember we came from the generic PHY path - update the error path to clean up the module reference in case the Generic PHY probe function fails - split the error path involving phy_detacht() to avoid double free/put since phy_detach() does all the clean up - finally, have phy_detach() drop the module reference count before we call device_release_driver() for the Generic PHY driver case Fixes: cafe8df8 ("net: phy: Fix lack of reference count on PHY driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Mao Wenan authored
[ Upstream commit cafe8df8 ] There is currently no reference count being held on the PHY driver, which makes it possible to remove the PHY driver module while the PHY state machine is running and polling the PHY. This could cause crashes similar to this one to show up: [ 43.361162] BUG: unable to handle kernel NULL pointer dereference at 0000000000000140 [ 43.361162] IP: phy_state_machine+0x32/0x490 [ 43.361162] PGD 59dc067 [ 43.361162] PUD 0 [ 43.361162] [ 43.361162] Oops: 0000 [#1] SMP [ 43.361162] Modules linked in: dsa_loop [last unloaded: broadcom] [ 43.361162] CPU: 0 PID: 1299 Comm: kworker/0:3 Not tainted 4.10.0-rc5+ #415 [ 43.361162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014 [ 43.361162] Workqueue: events_power_efficient phy_state_machine [ 43.361162] task: ffff880006782b80 task.stack: ffffc90000184000 [ 43.361162] RIP: 0010:phy_state_machine+0x32/0x490 [ 43.361162] RSP: 0018:ffffc90000187e18 EFLAGS: 00000246 [ 43.361162] RAX: 0000000000000000 RBX: ffff8800059e53c0 RCX: ffff880006a15c60 [ 43.361162] RDX: ffff880006782b80 RSI: 0000000000000000 RDI: ffff8800059e5428 [ 43.361162] RBP: ffffc90000187e48 R08: ffff880006a15c40 R09: 0000000000000000 [ 43.361162] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800059e5428 [ 43.361162] R13: ffff8800059e5000 R14: 0000000000000000 R15: ffff880006a15c40 [ 43.361162] FS: 0000000000000000(0000) GS:ffff880006a00000(0000) knlGS:0000000000000000 [ 43.361162] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 43.361162] CR2: 0000000000000140 CR3: 0000000005979000 CR4: 00000000000006f0 [ 43.361162] Call Trace: [ 43.361162] process_one_work+0x1b4/0x3e0 [ 43.361162] worker_thread+0x43/0x4d0 [ 43.361162] ? __schedule+0x17f/0x4e0 [ 43.361162] kthread+0xf7/0x130 [ 43.361162] ? process_one_work+0x3e0/0x3e0 [ 43.361162] ? kthread_create_on_node+0x40/0x40 [ 43.361162] ret_from_fork+0x29/0x40 [ 43.361162] Code: 56 41 55 41 54 4c 8d 67 68 53 4c 8d af 40 fc ff ff 48 89 fb 4c 89 e7 48 83 ec 08 e8 c9 9d 27 00 48 8b 83 60 ff ff ff 44 8b 73 98 <48> 8b 90 40 01 00 00 44 89 f0 48 85 d2 74 08 4c 89 ef ff d2 8b Keep references on the PHY driver module right before we are going to utilize it in phy_attach_direct(), and conversely when we don't use it anymore in phy_detach(). Signed-off-by:
Mao Wenan <maowenan@huawei.com> [florian: rebase, rework commit message] Signed-off-by:
-
Stanislaw Gruszka authored
[ Upstream commit 3808d348 ] If ->get_regs_len() callback return 0, we allocate 0 bytes of memory, what print ugly warning in dmesg, which can be found further below. This happen on mac80211 devices where ieee80211_get_regs_len() just return 0 and driver only fills ethtool_regs structure and actually do not provide any dump. However I assume this can happen on other drivers i.e. when for some devices driver provide regs dump and for others do not. Hence preventing to to print warning in ethtool code seems to be reasonable. ethtool: vmalloc: allocation failure: 0 bytes, mode:0x24080c2(GFP_KERNEL|__GFP_HIGHMEM|__GFP_ZERO) <snip> Call Trace: [<ffffffff813bde47>] dump_stack+0x63/0x8c [<ffffffff811b0a1f>] warn_alloc+0x13f/0x170 [<ffffffff811f0476>] __vmalloc_node_range+0x1e6/0x2c0 [<ffffffff811f0874>] vzalloc+0x54/0x60 [<ffffffff8169986c>] dev_ethtool+0xb4c/0x1b30 [<ffffffff816adbb1>] dev_ioctl+0x181/0x520 [<ffffffff816714d2>] sock_do_ioctl+0x42/0x50 <snip> Mem-Info: active_anon:435809 inactive_anon:173951 isolated_anon:0 active_file:835822 inactive_file:196932 isolated_file:0 unevictable:0 dirty:8 writeback:0 unstable:0 slab_reclaimable:157732 slab_unreclaimable:10022 mapped:83042 shmem:306356 pagetables:9507 bounce:0 free:130041 free_pcp:1080 free_cma:0 Node 0 active_anon:1743236kB inactive_anon:695804kB active_file:3343288kB inactive_file:787728kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:332168kB dirty:32kB writeback:0kB shmem:0kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 1225424kB writeback_tmp:0kB unstable:0kB pages_scanned:0 all_unreclaimable? no Node 0 DMA free:15900kB min:136kB low:168kB high:200kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15984kB managed:15900kB mlocked:0kB slab_reclaimable:0kB slab_unreclaimable:0kB kernel_stack:0kB pagetables:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB lowmem_reserve[]: 0 3187 7643 7643 Node 0 DMA32 free:419732kB min:28124kB low:35152kB high:42180kB active_anon:541180kB inactive_anon:248988kB active_file:1466388kB inactive_file:389632kB unevictable:0kB writepending:0kB present:3370280kB managed:3290932kB mlocked:0kB slab_reclaimable:217184kB slab_unreclaimable:4180kB kernel_stack:160kB pagetables:984kB bounce:0kB free_pcp:2236kB local_pcp:660kB free_cma:0kB lowmem_reserve[]: 0 0 4456 4456 Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Ard Biesheuvel authored
commit 29905b52 upstream. The function order_base_2() is defined (according to the comment block) as returning zero on input zero, but subsequently passes the input into roundup_pow_of_two(), which is explicitly undefined for input zero. This has gone unnoticed until now, but optimization passes in GCC 7 may produce constant folded function instances where a constant value of zero is passed into order_base_2(), resulting in link errors against the deliberately undefined '____ilog2_NaN'. So update order_base_2() to adhere to its own documented interface. [ See http://marc.info/?l=linux-kernel&m=147672952517795&w=2 and follow-up discussion for more background. The gcc "optimization pass" is really just broken, but now the GCC trunk problem seems to have escaped out of just specially built daily images, so we need to work around it in mainline. - Linus ] Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 4f40c6e5 ] After much waiting I finally reproduced a KASAN issue, only to find my trace-buffer empty of useful information because it got spooled out :/ Make kasan_report honour the /proc/sys/kernel/traceoff_on_warning interface. Link: http://lkml.kernel.org/r/20170125164106.3514-1-aryabinin@virtuozzo.comSigned-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by:
Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Kirill A. Shutemov authored
[ Upstream commit 253fd0f0 ] Syzkaller fuzzer managed to trigger this: BUG: sleeping function called from invalid context at mm/shmem.c:852 in_atomic(): 1, irqs_disabled(): 0, pid: 529, name: khugepaged 3 locks held by khugepaged/529: #0: (shrinker_rwsem){++++..}, at: [<ffffffff818d7ef1>] shrink_slab.part.59+0x121/0xd30 mm/vmscan.c:451 #1: (&type->s_umount_key#29){++++..}, at: [<ffffffff81a63630>] trylock_super+0x20/0x100 fs/super.c:392 #2: (&(&sbinfo->shrinklist_lock)->rlock){+.+.-.}, at: [<ffffffff818fd83e>] spin_lock include/linux/spinlock.h:302 [inline] #2: (&(&sbinfo->shrinklist_lock)->rlock){+.+.-.}, at: [<ffffffff818fd83e>] shmem_unused_huge_shrink+0x28e/0x1490 mm/shmem.c:427 CPU: 2 PID: 529 Comm: khugepaged Not tainted 4.10.0-rc5+ #201 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: shmem_undo_range+0xb20/0x2710 mm/shmem.c:852 shmem_truncate_range+0x27/0xa0 mm/shmem.c:939 shmem_evict_inode+0x35f/0xca0 mm/shmem.c:1030 evict+0x46e/0x980 fs/inode.c:553 iput_final fs/inode.c:1515 [inline] iput+0x589/0xb20 fs/inode.c:1542 shmem_unused_huge_shrink+0xbad/0x1490 mm/shmem.c:446 shmem_unused_huge_scan+0x10c/0x170 mm/shmem.c:512 super_cache_scan+0x376/0x450 fs/super.c:106 do_shrink_slab mm/vmscan.c:378 [inline] shrink_slab.part.59+0x543/0xd30 mm/vmscan.c:481 shrink_slab mm/vmscan.c:2592 [inline] shrink_node+0x2c7/0x870 mm/vmscan.c:2592 shrink_zones mm/vmscan.c:2734 [inline] do_try_to_free_pages+0x369/0xc80 mm/vmscan.c:2776 try_to_free_pages+0x3c6/0x900 mm/vmscan.c:2982 __perform_reclaim mm/page_alloc.c:3301 [inline] __alloc_pages_direct_reclaim mm/page_alloc.c:3322 [inline] __alloc_pages_slowpath+0xa24/0x1c30 mm/page_alloc.c:3683 __alloc_pages_nodemask+0x544/0xae0 mm/page_alloc.c:3848 __alloc_pages include/linux/gfp.h:426 [inline] __alloc_pages_node include/linux/gfp.h:439 [inline] khugepaged_alloc_page+0xc2/0x1b0 mm/khugepaged.c:750 collapse_huge_page+0x182/0x1fe0 mm/khugepaged.c:955 khugepaged_scan_pmd+0xfdf/0x12a0 mm/khugepaged.c:1208 khugepaged_scan_mm_slot mm/khugepaged.c:1727 [inline] khugepaged_do_scan mm/khugepaged.c:1808 [inline] khugepaged+0xe9b/0x1590 mm/khugepaged.c:1853 kthread+0x326/0x3f0 kernel/kthread.c:227 ret_from_fork+0x31/0x40 arch/x86/entry/entry_64.S:430 The iput() from atomic context was a bad idea: if after igrab() somebody else calls iput() and we left with the last inode reference, our iput() would lead to inode eviction and therefore sleeping. This patch should fix the situation. Link: http://lkml.kernel.org/r/20170131093141.GA15899@node.shutemov.nameSigned-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
David Lin authored
[ Upstream commit 35f860f9 ] Some versions of ARM GCC compiler such as Android toolchain throws in a '-fpic' flag by default. This causes the gcc-goto check script to fail although some config would have '-fno-pic' flag in the KBUILD_CFLAGS. This patch passes the KBUILD_CFLAGS to the check script so that the script does not rely on the default config from different compilers. Link: http://lkml.kernel.org/r/20170120234329.78868-1-dtwlin@google.comSigned-off-by:
David Lin <dtwlin@google.com> Acked-by:
Steven Rostedt <rostedt@goodmis.org> Cc: Michal Marek <mmarek@suse.com> Signed-off-by:
-
Rafael J. Wysocki authored
[ Upstream commit a9306a63 ] The might_sleep_if() assertions in __pm_runtime_idle(), __pm_runtime_suspend() and __pm_runtime_resume() may generate false-positive warnings in some situations. For example, that happens if a nested pm_runtime_get_sync()/pm_runtime_put() pair is executed with disabled interrupts within an outer pm_runtime_get_sync()/pm_runtime_put() section for the same device. [Generally, pm_runtime_get_sync() may sleep, so it should not be called with disabled interrupts, but in this particular case the previous pm_runtime_get_sync() guarantees that the device will not be suspended, so the inner pm_runtime_get_sync() will return immediately after incrementing the device's usage counter.] That started to happen in the i915 driver in 4.10-rc, leading to the following splat: BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1032 in_atomic(): 1, irqs_disabled(): 0, pid: 1500, name: Xorg 1 lock held by Xorg/1500: #0: (&dev->struct_mutex){+.+.+.}, at: [<ffffffffa0680c13>] i915_mutex_lock_interruptible+0x43/0x140 [i915] CPU: 0 PID: 1500 Comm: Xorg Not tainted Call Trace: dump_stack+0x85/0xc2 ___might_sleep+0x196/0x260 __might_sleep+0x53/0xb0 __pm_runtime_resume+0x7a/0x90 intel_runtime_pm_get+0x25/0x90 [i915] aliasing_gtt_bind_vma+0xaa/0xf0 [i915] i915_vma_bind+0xaf/0x1e0 [i915] i915_gem_execbuffer_relocate_entry+0x513/0x6f0 [i915] i915_gem_execbuffer_relocate_vma.isra.34+0x188/0x250 [i915] ? trace_hardirqs_on+0xd/0x10 ? i915_gem_execbuffer_reserve_vma.isra.31+0x152/0x1f0 [i915] ? i915_gem_execbuffer_reserve.isra.32+0x372/0x3a0 [i915] i915_gem_do_execbuffer.isra.38+0xa70/0x1a40 [i915] ? __might_fault+0x4e/0xb0 i915_gem_execbuffer2+0xc5/0x260 [i915] ? __might_fault+0x4e/0xb0 drm_ioctl+0x206/0x450 [drm] ? i915_gem_execbuffer+0x340/0x340 [i915] ? __fget+0x5/0x200 do_vfs_ioctl+0x91/0x6f0 ? __fget+0x111/0x200 ? __fget+0x5/0x200 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x23/0xc6 even though the code triggering it is correct. Unfortunately, the might_sleep_if() assertions in question are too coarse-grained to cover such cases correctly, so make them a bit less sensitive in order to avoid the false-positives. Reported-and-tested-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 5aff1d24 ] The symbols can no longer be used as loadable modules, leading to a harmless Kconfig warning: arch/arm/configs/imote2_defconfig:60:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE arch/arm/configs/imote2_defconfig:59:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP arch/arm/configs/ezx_defconfig:68:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE arch/arm/configs/ezx_defconfig:67:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP Let's make them built-in. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Linus Lüssing authored
[ Upstream commit a088d1d7 ] When for instance a mobile Linux device roams from one access point to another with both APs sharing the same broadcast domain and a multicast snooping switch in between: 1) (c) <~~~> (AP1) <--[SSW]--> (AP2) 2) (AP1) <--[SSW]--> (AP2) <~~~> (c) Then currently IPv6 multicast packets will get lost for (c) until an MLD Querier sends its next query message. The packet loss occurs because upon roaming the Linux host so far stayed silent regarding MLD and the snooping switch will therefore be unaware of the multicast topology change for a while. This patch fixes this by always resending MLD reports when an interface change happens, for instance from NO-CARRIER to CARRIER state. Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by:
-
Alexey Kardashevskiy authored
[ Upstream commit 930a42de ] If a container already has a group attached, attaching a new group should just program already created IOMMU tables to the hardware via the iommu_table_group_ops::set_window() callback. However commit 6f01cc69 ("vfio/spapr: Add a helper to create default DMA window") did not just simplify the code but also removed the set_window() calls in the case of attaching groups to a container which already has tables so it broke VFIO PCI hotplug. This reverts set_window() bits in tce_iommu_take_ownership_ddw(). Fixes: 6f01cc69 ("vfio/spapr: Add a helper to create default DMA window") Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Marcus Huewe authored
[ Upstream commit a11a7f71 ] Under some circumstances it is possible that no new temporary addresses will be generated. For instance, addrconf_prefix_rcv_add_addr() indirectly calls ipv6_create_tempaddr(), which creates a tentative temporary address and starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls addrconf_verify_rtnl(). Now, assume that the previously created temporary address has the least preferred lifetime among all existing addresses and is still tentative (that is, dad is still running). Hence, the next run of addrconf_verify_rtnl() is performed when the preferred lifetime of the temporary address ends. If dad succeeds before the next run, the temporary address becomes deprecated during the next run, but no new temporary address is generated. In order to fix this, schedule the next addrconf_verify_rtnl() run slightly before the temporary address becomes deprecated, if dad succeeded. Signed-off-by:
Marcus Huewe <suse-tux@gmx.de> Signed-off-by:
-
Thanneeru Srinivasulu authored
[ Upstream commit 075ad765 ] This patch fixes the case where there is no phydev attached to a LMAC in DT due to non-existance of a PHY driver or due to usage of non-stanadard PHY which doesn't support autoneg. Changes dependeds on firmware to send correct info w.r.t PHY and autoneg capability. This patch also covers a case where a 10G/40G interface is used as a 1G with convertors with Cortina PHY in between. Signed-off-by:
Thanneeru Srinivasulu <tsrinivasulu@cavium.com> Signed-off-by:
Sunil Goutham <sgoutham@cavium.com> Signed-off-by:
-
Luis R. Rodriguez authored
[ Upstream commit ed5bd7dc ] The user_header gets caught by kmemleak with the following splat as missing a free: unreferenced object 0xffff99667a733d80 (size 96): comm "swapper/0", pid 1, jiffies 4294892317 (age 62191.468s) hex dump (first 32 bytes): a0 b6 92 b4 ff ff ff ff 00 00 00 00 01 00 00 00 ................ 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: kmemleak_alloc+0x4a/0xa0 __kmalloc+0x144/0x260 __register_sysctl_table+0x54/0x5e0 register_sysctl+0x1b/0x20 user_namespace_sysctl_init+0x17/0x34 do_one_initcall+0x52/0x1a0 kernel_init_freeable+0x173/0x200 kernel_init+0xe/0x100 ret_from_fork+0x2c/0x40 The BUG_ON()s are intended to crash so no need to clean up after ourselves on error there. This is also a kernel/ subsys_init() we don't need a respective exit call here as this is never modular, so just white list it. Link: http://lkml.kernel.org/r/20170203211404.31458-1-mcgrof@kernel.orgSigned-off-by:
Luis R. Rodriguez <mcgrof@kernel.org> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Kees Cook <keescook@chromium.org> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Cc: Serge Hallyn <serge@hallyn.com> Cc: Jan Kara <jack@suse.cz> Signed-off-by:
-
Benjamin Herrenschmidt authored
[ Upstream commit f83e6862 ] Otherwise KVM will fail to pass them through to the host Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Ricardo Ribalda authored
[ Upstream commit f43128c7 ] Since '701dc207 ("i2c: piix4: Avoid race conditions with IMC")' we are using the SMBSLVCNT register at offset 0x8. We need to request it. Fixes: 701dc207 ("i2c: piix4: Avoid race conditions with IMC") Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Ricardo Ribalda authored
[ Upstream commit bbb27fc3 ] SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid multiple buses accessing to the semaphore at the same time. Fixes: 701dc207 ("i2c: piix4: Avoid race conditions with IMC") Reported-by:
-
Stefan Brüns authored
[ Upstream commit 5a70348e ] If a context is configured as dualstack ("IPv4v6"), the modem indicates the context activation with a slightly different indication message. The dual-stack indication omits the link_type (IPv4/v6) and adds additional address fields. IPv6 LSIs are identical to IPv4 LSIs, but have a different link type. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Stefan Brüns authored
[ Upstream commit 764895d3 ] When the context is deactivated, the link_type is set to 0xff, which triggers a warning message, and results in a wrong link status, as the LSI is ignored. Signed-off-by:
-
Kejian Yan authored
[ Upstream commit b85ea006 ] This patch fixes the device being used to DMA map skb->data. Erroneous device assignment causes the crash when SMMU is enabled. This happens during TX since buffer gets DMA mapped with device correspondign to net_device and gets unmapped using the device related to DSAF. Signed-off-by:
Kejian Yan <yankejian@huawei.com> Reviewed-by:
Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
-
Ralf Baechle authored
[ Upstream commit 7ba1b689 ] If a USB-to-serial adapter is unplugged, the driver re-initializes, with dev->hard_header_len and dev->addr_len set to zero, instead of the correct values. If then a packet is sent through the half-dead interface, the kernel will panic due to running out of headroom in the skb when pushing for the AX.25 headers resulting in this panic: [<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50) [<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25]) [<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss]) [<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8) [<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914) [<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0) [<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48) This patch makes mkiss behave like the 6pack driver. 6pack does not panic. In 6pack.c sp_setup() (same function name here) the values for dev->hard_header_len and dev->addr_len are set to the same values as in my mkiss patch. [ralf@linux-mips.org: Massages original submission to conform to the usual standards for patch submissions.] Signed-off-by:
Thomas Osterried <thomas@osterried.de> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Nathan Fontenot authored
[ Upstream commit db5d0b59 ] Initialize condition variables prior to invoking any work that can mark them complete. This resolves a race in the ibmvnic driver where the driver faults trying to complete an uninitialized condition variable. Signed-off-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
-
Nathan Fontenot authored
[ Upstream commit e722af63 ] The failure path in ibmvnic_open() mistakenly makes a second call to napi_enable instead of calling napi_disable. This can result in a BUG_ON for any queues that were enabled in the previous call to napi_enable. Signed-off-by:
-
Ralf Baechle authored
[ Upstream commit 4872e57c ] When sending ARP requests over AX.25 links the hwaddress in the neighbour cache are not getting initialized. For such an incomplete arp entry ax2asc2 will generate an empty string resulting in /proc/net/arp output like the following: $ cat /proc/net/arp IP address HW type Flags HW address Mask Device 192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3 172.20.1.99 0x3 0x0 * bpq0 The missing field will confuse the procfs parsing of arp(8) resulting in incorrect output for the device such as the following: $ arp Address HWtype HWaddress Flags Mask Iface gateway ether 52:54:00:00:5d:5f C ens3 172.20.1.99 (incomplete) ens3 This changes the content of /proc/net/arp to: $ cat /proc/net/arp IP address HW type Flags HW address Mask Device 172.20.1.99 0x3 0x0 * * bpq0 192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3 To do so it change ax2asc to put the string "*" in buf for a NULL address argument. Finally the HW address field is left aligned in a 17 character field (the length of an ethernet HW address in the usual hex notation) for readability. Signed-off-by:
-
Herbert Xu authored
[ Upstream commit 6a254780 ] The function glock_hash_walk walks the rhashtable by hand. This is broken because if it catches the hash table in the middle of a rehash, then it will miss entries. This patch replaces the manual walk by using the rhashtable walk interface. Fixes: 88ffbf3e ("GFS2: Use resizable hash table for glocks") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
[ Upstream commit 9dbbfb0a ] There are two problems with the function tipc_sk_reinit. Firstly it's doing a manual walk over an rhashtable. This is broken as an rhashtable can be resized and if you manually walk over it during a resize then you may miss entries. Secondly it's missing memory barriers as previously the code used spinlocks which provide the barriers implicitly. This patch fixes both problems. Fixes: 07f6c4bc ("tipc: convert tipc reference table to...") Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Jonathan T. Leighton authored
[ Upstream commit ec5e3b0a ] This patch adds a check for the problematic case of an IPv4-mapped IPv6 source address and a destination address that is neither an IPv4-mapped IPv6 address nor in6addr_any, and returns an appropriate error. The check in done before returning from looking up the route. Signed-off-by:
Jonathan T. Leighton <jtleight@udel.edu> Signed-off-by:
-
