- 26 Sep, 2018 40 commits
-
-
Stefan Agner authored
[ Upstream commit 127407e3 ] The stack assumes that SDHC controller which support SD3.0 (SDR104) do support HS200. This is not the case for Tegra 3, which does support SD 3.0 but only supports eMMC spec 4.41. Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not support HS200. Note that commit 156e14b1 ("mmc: sdhci: fix caps2 for HS200") added the tie between SD3.0 (SDR104) and HS200. I don't think that this is necessarly true. It is fully legitimate to support SD3.0 and not support HS200. The quirk naming suggests something is broken in the controller, but this is not the case: The controller simply does not support HS200. Fixes: 7ad2ed1d ("mmc: tegra: enable UHS-I modes") Signed-off-by:
Stefan Agner <stefan@agner.ch> Tested-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Enrico Scholz authored
[ Upstream commit d36d0e63 ] mbus_code_to_bus_cfg() can fail on unknown mbus codes; pass back the error to the caller. Signed-off-by:
Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by:
Jan Luebbe <jlu@pengutronix.de> [p.zabel@pengutronix.de - renamed rc to ret for consistency] Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit 81646a3d ] of_find_compatible_node() returns a device node with refcount incremented and thus needs an explicit of_node_put(). Further relying on an unchecked of_iomap() which can return NULL is problematic here, after all ctrl_base is critical enough for hix5hd2_set_cpu() to call BUG() if not available so a check seems mandated here. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> 0002 Fixes: commit 06cc5c1d ("ARM: hisi: enable hix5hd2 SoC") Signed-off-by:
Wei Xu <xuwei5@hisilicon.com> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit 9f30b5ae ] of_iomap() can return NULL which seems critical here and thus should be explicitly flagged so that the cause of system halting can be understood. As of_find_compatible_node() is returning a device node with refcount incremented it must be explicitly decremented here. Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit d396cb18 ] Relying on an unchecked of_iomap() which can return NULL is problematic here, an explicit check seems mandatory. Also the call to of_find_compatible_node() returns a device node with refcount incremented therefor an explicit of_node_put() is needed here. Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit 61f0d555 ] The following commit: 7e1550b8 ("efi: Drop type and attribute checks in efi_mem_desc_lookup()") refactored the implementation of efi_mem_desc_lookup() so that the type check is moved to the callers, one of which is the x86 version of efi_arch_mem_reserve(), where we added a modified check that only takes EFI_BOOT_SERVICES_DATA regions into account. This is reasonable, since it is the only memory type that requires this, but doing so uncovered some unexpected behavior in the ESRT code, which permits the ESRT table to reside in other types of memory than what the UEFI spec mandates (i.e., EFI_BOOT_SERVICES_DATA), and unconditionally calls efi_mem_reserve() on the region in question. This may result in errors such as esrt: Reserving ESRT space from 0x000000009c810318 to 0x000000009c810350. efi: Failed to lookup EFI memory descriptor for 0x000000009c810318 when the ESRT table is not in EFI_BOOT_SERVICES_DATA memory, but we try to reserve it nonetheless. So make the call to efi_mem_reserve() conditional on the memory type. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Mike Christie authored
[ Upstream commit cc57c073 ] This patch fixes a bug where configfs_register_group had added a group in a tree, and userspace has done a rmdir on a dir somewhere above that group and we hit a kernel crash. The problem is configfs_rmdir will detach everything under it and unlink groups on the default_groups list. It will not unlink groups added with configfs_register_group so when configfs_unregister_group is called to drop its references to the group/items we crash when we try to access the freed dentrys. The patch just adds a check for if a rmdir has been done above us and if so just does the unlink part of unregistration. Sorry if you are getting this multiple times. I thouhgt I sent this to some of you and lkml, but I do not see it. Signed-off-by:
Mike Christie <mchristi@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Paul Burton authored
[ Upstream commit cd87668d ] The PCI_OHCI_INT_REG case in pci_ohci_read_reg() contains the following if statement: if ((lo & 0x00000f00) == CS5536_USB_INTR) CS5536_USB_INTR expands to the constant 11, which gives us the following condition which can never evaluate true: if ((lo & 0xf00) == 11) At least when using GCC 8.1.0 this falls foul of the tautoligcal-compare warning, and since the code is built with the -Werror flag the build fails. Fix this by shifting lo right by 8 bits in order to match the corresponding PCI_OHCI_INT_REG case in pci_ohci_write_reg(). Signed-off-by:
Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19861/ Cc: Huacai Chen <chenhc@lemote.com> Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Signed-off-by:
-
Matthew Garrett authored
[ Upstream commit e2861fa7 ] When EVM attempts to appraise a file signed with a crypto algorithm the kernel doesn't have support for, it will cause the kernel to trigger a module load. If the EVM policy includes appraisal of kernel modules this will in turn call back into EVM - since EVM is holding a lock until the crypto initialisation is complete, this triggers a deadlock. Add a CRYPTO_NOLOAD flag and skip module loading if it's set, and add that flag in the EVM case in order to fail gracefully with an error message instead of deadlocking. Signed-off-by:
Matthew Garrett <mjg59@google.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Jann Horn authored
[ Upstream commit 6c6bc9ea ] The first checks in mtdchar_read() and mtdchar_write() attempt to limit `count` such that `*ppos + count <= mtd->size`. However, they ignore the possibility of `*ppos > mtd->size`, allowing the calculation of `count` to wrap around. `mtdchar_lseek()` prevents seeking beyond mtd->size, but the pread/pwrite syscalls bypass this. I haven't found any codepath on which this actually causes dangerous behavior, but it seems like a sensible change anyway. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by:
-
Ronny Chevalier authored
[ Upstream commit baa2a4fd ] audit_add_watch stores locally krule->watch without taking a reference on watch. Then, it calls audit_add_to_parent, and uses the watch stored locally. Unfortunately, it is possible that audit_add_to_parent updates krule->watch. When it happens, it also drops a reference of watch which could free the watch. How to reproduce (with KASAN enabled): auditctl -w /etc/passwd -F success=0 -k test_passwd auditctl -w /etc/passwd -F success=1 -k test_passwd2 The second call to auditctl triggers the use-after-free, because audit_to_parent updates krule->watch to use a previous existing watch and drops the reference to the newly created watch. To fix the issue, we grab a reference of watch and we release it at the end of the function. Signed-off-by:
Ronny Chevalier <ronny.chevalier@hp.com> Reviewed-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Maciej W. Rozycki authored
[ Upstream commit 2f819db5 ] The regset API documented in <linux/regset.h> defines -ENODEV as the result of the `->active' handler to be used where the feature requested is not available on the hardware found. However code handling core file note generation in `fill_thread_core_info' interpretes any non-zero result from the `->active' handler as the regset requested being active. Consequently processing continues (and hopefully gracefully fails later on) rather than being abandoned right away for the regset requested. Fix the problem then by making the code proceed only if a positive result is returned from the `->active' handler. Signed-off-by:
Maciej W. Rozycki <macro@mips.com> Signed-off-by:
-
Trond Myklebust authored
commit 994b15b9 upstream. The previous fix broke recovery of delegated stateids because it assumes that if we did not mark the delegation as suspect, then the delegation has effectively been revoked, and so it removes that delegation irrespectively of whether or not it is valid and still in use. While this is "mostly harmless" for ordinary I/O, we've seen pNFS fail with LAYOUTGET spinning in an infinite loop while complaining that we're using an invalid stateid (in this case the all-zero stateid). What we rather want to do here is ensure that the delegation is always correctly marked as needing testing when that is the case. So we want to close the loophole offered by nfs4_schedule_stateid_recovery(), which marks the state as needing to be reclaimed, but not the delegation that may be backing it. Fixes: 0e3d3e5d ("NFSv4.1 fix infinite loop on IO BAD_STATEID error") Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Cc: stable@vger.kernel.org # v4.11+ Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Yabin Cui authored
commit 02e18447 upstream. Perf can record user stack data in response to a synchronous request, such as a tracepoint firing. If this happens under set_fs(KERNEL_DS), then we end up reading user stack data using __copy_from_user_inatomic() under set_fs(KERNEL_DS). I think this conflicts with the intention of using set_fs(KERNEL_DS). And it is explicitly forbidden by hardware on ARM64 when both CONFIG_ARM64_UAO and CONFIG_ARM64_PAN are used. So fix this by forcing USER_DS when recording user stack data. Signed-off-by:
Yabin Cui <yabinc@google.com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 88b0193d ("perf/callchain: Force USER_DS when invoking perf_callchain_user()") Link: http://lkml.kernel.org/r/20180823225935.27035-1-yabinc@google.comSigned-off-by:
-
Dan Carpenter authored
commit 56446f21 upstream. The problem is that "entryptr + next_offset" and "entryptr + len + size" can wrap. I ended up changing the type of "entryptr" because it makes the math easier when we don't have to do so much casting. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Aurelien Aptel <aaptel@suse.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
-
Dan Carpenter authored
commit 8ad8aa35 upstream. The "old_entry + le32_to_cpu(pDirInfo->NextEntryOffset)" can wrap around so I have added a check for integer overflow. Reported-by:
Dr Silvio Cesare of InfoSect <silvio.cesare@gmail.com> Reviewed-by:
Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by:
-
Oliver Neukum authored
commit df3aa13c upstream. This reverts commit a81cf979. The patch causes a regression, which I cannot find the reason for. So let's revert for now, as a revert hurts only performance. Original report: I was trying to resolve the problem with Oliver but we don't get any conclusion for 5 months, so I am now sending this to mail list and cdc_acm authors. I am using simple request-response protocol to obtain the boiller parameters in constant intervals. A simple one transaction is: 1. opening the /dev/ttyACM0 2. sending the following 10-bytes request to the device: unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03}; 3. reading response (frame of 74 bytes length). 4. closing the descriptor I am doing this transaction with 5 seconds intervals. Before the bad commit everything was working correctly: I've got a requests and a responses in a timely manner. After the bad commit more time I am using the kernel module, more problems I have. The graph [2] is showing the problem. As you can see after module load all seems fine but after about 30 minutes I've got a plenty of EAGAINs when doing read()'s and trying to read back the data. When I rmmod and insmod the cdc_acm module again, then the situation is starting over again: running ok shortly after load, and more time it is running, more EAGAINs I have when calling read(). As a bonus I can see the problem on the device itself: The device is configured as you can see here on this screen [3]. It has two transmision LEDs: TX and RX. Blink duration is set for 100ms. This is a recording before the bad commit when all is working fine: [4] And this is with the bad commit: [5] As you can see the TX led is blinking wrongly long (indicating transmission?) and I have problems doing read() calls (EAGAIN). Reported-by:
Mariusz Bialonczyk <manio@skyboo.net> Signed-off-by:
Oliver Neukum <oneukum@suse.com> Fixes: a81cf979 ("cdc-acm: implement put_char() and flush_chars()") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Jia-Ju Bai authored
commit 6e22e3af upstream. wdm_in_callback() is a completion handler function for the USB driver. So it should not sleep. But it calls service_outstanding_interrupt(), which calls usb_submit_urb() with GFP_KERNEL. To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC. This bug is found by my static analysis tool DSAC. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Ben Hutchings authored
commit 7e10f14e upstream. If the written data starts with a digit, yurex_write() tries to parse it as an integer using simple_strtoull(). This requires a null- terminator, and currently there's no guarantee that there is one. (The sample program at https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl writes an integer without a null terminator. It seems like it must have worked by chance!) Always add a null byte after the written data. Enlarge the buffer to allow for this. Cc: stable@vger.kernel.org Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Johan Hovold authored
commit 5dfdd24e upstream. Similarly to a recently reported bug in io_ti, a malicious USB device could set port_number to a negative value and we would underflow the port array in the interrupt completion handler. As these devices only have one or two ports, fix this by making sure we only consider the seventh bit when determining the port number (and ignore bits 0xb0 which are typically set to 0x30). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Jia-Ju Bai authored
commit bc8acc21 upstream. async_complete() in uss720.c is a completion handler function for the USB driver. So it should not sleep, but it is can sleep according to the function call paths (from bottom to top) in Linux-4.16. [FUNC] set_1284_register(GFP_KERNEL) drivers/usb/misc/uss720.c, 372: set_1284_register in parport_uss720_frob_control drivers/parport/ieee1284.c, 560: [FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail drivers/parport/ieee1284.c, 577: parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt ./include/linux/parport.h, 474: parport_ieee1284_interrupt in parport_generic_irq drivers/usb/misc/uss720.c, 116: parport_generic_irq in async_complete [FUNC] get_1284_register(GFP_KERNEL) drivers/usb/misc/uss720.c, 382: get_1284_register in parport_uss720_read_status drivers/parport/ieee1284.c, 555: [FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail drivers/parport/ieee1284.c, 577: parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt ./include/linux/parport.h, 474: parport_ieee1284_interrupt in parport_generic_irq drivers/usb/misc/uss720.c, 116: parport_generic_irq in async_complete Note that [FUNC_PTR] means a function pointer call is used. To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC. These bugs are found by my static analysis tool DSAC. Signed-off-by:
-
Johan Hovold authored
commit 691a03cf upstream. As reported by Dan Carpenter, a malicious USB device could set port_number to a negative value and we would underflow the port array in the interrupt completion handler. As these devices only have one or two ports, fix this by making sure we only consider the seventh bit when determining the port number (and ignore bits 0xb0 which are typically set to 0x30). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reported-by:
-
Alan Stern authored
commit dec3c23c upstream. Commit f16443a0 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks") was based on a serious misunderstanding. It introduced regressions into both the dummy-hcd and net2280 drivers. The problem in dummy-hcd was fixed by commit 7dbd8f4c ("USB: dummy-hcd: Fix erroneous synchronization change"), but the problem in net2280 remains. Namely: the ->disconnect(), ->suspend(), ->resume(), and ->reset() callbacks must be invoked without the private lock held; otherwise a deadlock will occur when the callback routine tries to interact with the UDC driver. This patch largely is a reversion of the relevant parts of f16443a0. It also drops the private lock around the calls to ->suspend() and ->resume() (something the earlier patch forgot to do). This is safe from races with device interrupts because it occurs within the interrupt handler. Finally, the patch changes where the ->disconnect() callback is invoked when net2280_pullup() turns the pullup off. Rather than making the callback from within stop_activity() at a time when dropping the private lock could be unsafe, the callback is moved to a point after the lock has already been dropped. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Fixes: f16443a0 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks") Reported-by:
D. Ziesche <dziesche@zes.com> Tested-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Yoshihiro Shimoda authored
commit dfe1a51d upstream. This patch fixes an issue that maxpacket size of ep0 is incorrect for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't work correctly on this driver because its control read data size is more than 64 bytes. Reported-by:
Junki Kato <junki.kato.xk@renesas.com> Fixes: 746bfe63 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by:
-
Maxence Duprès authored
commit 9b83a1c3 upstream. WORLDE Controller KS49 or Prodipe MIDI 49C USB controller cause a -EPROTO error, a communication restart and loop again. This issue has already been fixed for KS25. https://lore.kernel.org/patchwork/patch/753077/ I just add device 201 for KS49 in quirks.c to get it works. Signed-off-by:
Laurent Roux <xpros64@hotmail.fr> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Jia-Ju Bai authored
commit 6d4f268f upstream. i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function for the USB driver. So it should not sleep, but it is can sleep according to the function call paths (from bottom to top) in Linux-4.16. [FUNC] msleep drivers/usb/host/u132-hcd.c, 2558: msleep in u132_get_frame drivers/usb/core/hcd.c, 2231: [FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number drivers/usb/core/usb.c, 822: usb_hcd_get_frame_number in usb_get_current_frame_number sound/usb/usx2y/usbusx2yaudio.c, 303: usb_get_current_frame_number in i_usX2Y_urb_complete sound/usb/usx2y/usbusx2yaudio.c, 366: i_usX2Y_urb_complete in i_usX2Y_subs_startup Note that [FUNC_PTR] means a function pointer call is used. To fix this bug, msleep() is replaced with mdelay(). This bug is found by my static analysis tool DSAC. Signed-off-by:
-
Mathias Nyman authored
commit f9a5b4f5 upstream. The steps taken by usb core to set a new interface is very different from what is done on the xHC host side. xHC hardware will do everything in one go. One command is used to set up new endpoints, free old endpoints, check bandwidth, and run the new endpoints. All this is done by xHC when usb core asks the hcd to check for available bandwidth. At this point usb core has not yet flushed the old endpoints, which will cause use-after-free issues in xhci driver as queued URBs are cancelled on a re-allocated endpoint. To resolve this add a call to usb_disable_interface() which will flush the endpoints before calling usb_hcd_alloc_bandwidth() Additional checks in xhci driver will also be implemented to gracefully handle stale URB cancel on freed and re-allocated endpoints Cc: <stable@vger.kernel.org> Reported-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by:
-
Oliver Neukum authored
commit 42d1c6d4 upstream. The hope that UAS devices would be less broken than old style storage devices has turned out to be unfounded. Make UAS support more of the quirk flags of the old driver. Signed-off-by:
-
Tim Anderson authored
commit f45681f9 upstream. This device does not correctly handle the LPM operations. Also, the device cannot handle ATA pass-through commands and locks up when attempted while running in super speed. This patch adds the equivalent quirk logic as found in uas. Signed-off-by:
Tim Anderson <tsa@biglakesoftware.com> Acked-by:
-
Alexander Usyskin authored
commit 8d2d8935 upstream. Some of the ME clients are available only for BIOS operation and are removed during hand off to an OS. However the removal is not instant. A client may be visible on the client list when the mei driver requests for enumeration, while the subsequent request for properties will be answered with client not found error value. The default behavior for an error is to perform client reset while this error is harmless and the link reset should be prevented. This issue started to be visible due to suspend/resume timing changes. Currently reported only on the Haswell based system. Fixes: [33.564957] mei_me 0000:00:16.0: hbm: properties response: wrong status = 1 CLIENT_NOT_FOUND [33.564978] mei_me 0000:00:16.0: mei_irq_read_handler ret = -71. [33.565270] mei_me 0000:00:16.0: unexpected reset: dev_state = INIT_CLIENTS fw status = 1E000255 60002306 00000200 00004401 00000000 00000010 Cc: <stable@vger.kernel.org> Reported-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Mathias Nyman authored
commit f3dc41c5 upstream. usb_hc_died() should only be called once, and with the primary HCD as parameter. It will mark both primary and secondary hcd's dead. Remove the extra call to usb_cd_died with the shared hcd as parameter. Fixes: ff9d78b3 ("USB: Set usb_hcd->state and flags for shared roothubs") Signed-off-by:
-
Gustavo A. R. Silva authored
commit de916736 upstream. val is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/misc/hmc6352.c:54 compass_store() warn: potential spectre issue 'map' [r] Fix this by sanitizing val before using it to index map Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
K. Y. Srinivasan authored
commit 86503bd3 upstream. Fix a bug in the key delete code - the num_records range from 0 to num_records-1. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reported-by:
David Binderman <dcb314@hotmail.com> Cc: <stable@vger.kernel.org> Reviewed-by:
Michael Kelley <mikelley@microsoft.com> Signed-off-by:
-
Andreas Kemnade authored
commit 3c398f3c upstream. after unbinding mmc I get things like this: [ 185.294067] mmc1: card 0001 removed [ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13 The wakeirq stays in /proc-interrupts rebinding shows this: [ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup) [ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ [ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling That bug seems to be introduced by switching from devm_request_irq() to generic wakeirq handling. So let us cleanup at removal. Signed-off-by:
Andreas Kemnade <andreas@kemnade.info> Fixes: 5b83b223 ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by:
-
Aaron Knister authored
commit 816e846c upstream. Inside of start_xmit() the call to check if the connection is up and the queueing of the packets for later transmission is not atomic which leaves a window where cm_rep_handler can run, set the connection up, dequeue pending packets and leave the subsequently queued packets by start_xmit() sitting on neigh->queue until they're dropped when the connection is torn down. This only applies to connected mode. These dropped packets can really upset TCP, for example, and cause multi-minute delays in transmission for open connections. Here's the code in start_xmit where we check to see if the connection is up: if (ipoib_cm_get(neigh)) { if (ipoib_cm_up(neigh)) { ipoib_cm_send(dev, skb, ipoib_cm_get(neigh)); goto unref; } } The race occurs if cm_rep_handler execution occurs after the above connection check (specifically if it gets to the point where it acquires priv->lock to dequeue pending skb's) but before the below code snippet in start_xmit where packets are queued. if (skb_queue_len(&neigh->queue) < IPOIB_MAX_PATH_REC_QUEUE) { push_pseudo_header(skb, phdr->hwaddr); spin_lock_irqsave(&priv->lock, flags); __skb_queue_tail(&neigh->queue, skb); spin_unlock_irqrestore(&priv->lock, flags); } else { ++dev->stats.tx_dropped; dev_kfree_skb_any(skb); } The patch acquires the netif tx lock in cm_rep_handler for the section where it sets the connection up and dequeues and retransmits deferred skb's. Fixes: 839fcaba ("IPoIB: Connected mode experimental support") Cc: stable@vger.kernel.org Signed-off-by:
Aaron Knister <aaron.s.knister@nasa.gov> Tested-by:
Ira Weiny <ira.weiny@intel.com> Reviewed-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Juergen Gross authored
commit 8edfe2e9 upstream. Commit 822fb18a ("xen-netfront: wait xenbus state change when load module manually") added a new wait queue to wait on for a state change when the module is loaded manually. Unfortunately there is no wakeup anywhere to stop that waiting. Instead of introducing a new wait queue rename the existing module_unload_q to module_wq and use it for both purposes (loading and unloading). As any state change of the backend might be intended to stop waiting do the wake_up_all() in any case when netback_changed() is called. Fixes: 822fb18a ("xen-netfront: wait xenbus state change when load module manually") Cc: <stable@vger.kernel.org> #4.18 Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Bin Yang authored
commit 831b624d upstream. persistent_ram_vmap() returns the page start vaddr. persistent_ram_iomap() supports non-page-aligned mapping. persistent_ram_buffer_map() always adds offset-in-page to the vaddr returned from these two functions, which causes incorrect mapping of non-page-aligned persistent ram buffer. By default ftrace_size is 4096 and max_ftrace_cnt is nr_cpu_ids. Without this patch, the zone_sz in ramoops_init_przs() is 4096/nr_cpu_ids which might not be page aligned. If the offset-in-page > 2048, the vaddr will be in next page. If the next page is not mapped, it will cause kernel panic: [ 0.074231] BUG: unable to handle kernel paging request at ffffa19e0081b000 ... [ 0.075000] RIP: 0010:persistent_ram_new+0x1f8/0x39f ... [ 0.075000] Call Trace: [ 0.075000] ramoops_init_przs.part.10.constprop.15+0x105/0x260 [ 0.075000] ramoops_probe+0x232/0x3a0 [ 0.075000] platform_drv_probe+0x3e/0xa0 [ 0.075000] driver_probe_device+0x2cd/0x400 [ 0.075000] __driver_attach+0xe4/0x110 [ 0.075000] ? driver_probe_device+0x400/0x400 [ 0.075000] bus_for_each_dev+0x70/0xa0 [ 0.075000] driver_attach+0x1e/0x20 [ 0.075000] bus_add_driver+0x159/0x230 [ 0.075000] ? do_early_param+0x95/0x95 [ 0.075000] driver_register+0x70/0xc0 [ 0.075000] ? init_pstore_fs+0x4d/0x4d [ 0.075000] __platform_driver_register+0x36/0x40 [ 0.075000] ramoops_init+0x12f/0x131 [ 0.075000] do_one_initcall+0x4d/0x12c [ 0.075000] ? do_early_param+0x95/0x95 [ 0.075000] kernel_init_freeable+0x19b/0x222 [ 0.075000] ? rest_init+0xbb/0xbb [ 0.075000] kernel_init+0xe/0xfc [ 0.075000] ret_from_fork+0x3a/0x50 Signed-off-by:
Bin Yang <bin.yang@intel.com> [kees: add comments describing the mapping differences, updated commit log] Fixes: 24c3d2f3 ("staging: android: persistent_ram: Make it possible to use memory outside of bootmem") Cc: stable@vger.kernel.org Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Parav Pandit authored
commit 954a8e3a upstream. When AF_IB addresses are used during rdma_resolve_addr() a lock is not held. A cma device can get removed while list traversal is in progress which may lead to crash. ie CPU0 CPU1 ==== ==== rdma_resolve_addr() cma_resolve_ib_dev() list_for_each() cma_remove_one() cur_dev->device mutex_lock(&lock) list_del(); mutex_unlock(&lock); cma_process_remove(); Therefore, hold a lock while traversing the list which avoids such situation. Cc: <stable@vger.kernel.org> # 3.10 Fixes: f17df3b0 ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()") Signed-off-by:
Parav Pandit <parav@mellanox.com> Reviewed-by:
Daniel Jurgens <danielj@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Reviewed-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
-
Xiao Liang authored
[ Upstream commit 21f2706b ] There is a call trace generated after commit 2d408c0d( xen-netfront: fix queue name setting). There is no 'device/vif/xx-q0-tx' file found under /proc/irq/xx/. This patch only picks up device type and id as its name. With the patch, now /proc/interrupts looks like below and the warning message gone: 70: 21 0 0 0 xen-dyn -event vif0-q0-tx 71: 15 0 0 0 xen-dyn -event vif0-q0-rx 72: 14 0 0 0 xen-dyn -event vif0-q1-tx 73: 33 0 0 0 xen-dyn -event vif0-q1-rx 74: 12 0 0 0 xen-dyn -event vif0-q2-tx 75: 24 0 0 0 xen-dyn -event vif0-q2-rx 76: 19 0 0 0 xen-dyn -event vif0-q3-tx 77: 21 0 0 0 xen-dyn -event vif0-q3-rx Below is call trace information without this patch: name 'device/vif/0-q0-tx' WARNING: CPU: 2 PID: 37 at fs/proc/generic.c:174 __xlate_proc_name+0x85/0xa0 RIP: 0010:__xlate_proc_name+0x85/0xa0 RSP: 0018:ffffb85c40473c18 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000006 RCX: 0000000000000006 RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff984c7f516930 RBP: ffffb85c40473cb8 R08: 000000000000002c R09: 0000000000000229 R10: 0000000000000000 R11: 0000000000000001 R12: ffffb85c40473c98 R13: ffffb85c40473cb8 R14: ffffb85c40473c50 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff984c7f500000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f69b6899038 CR3: 000000001c20a006 CR4: 00000000001606e0 Call Trace: __proc_create+0x45/0x230 ? snprintf+0x49/0x60 proc_mkdir_data+0x35/0x90 register_handler_proc+0xef/0x110 ? proc_register+0xfc/0x110 ? proc_create_data+0x70/0xb0 __setup_irq+0x39b/0x660 ? request_threaded_irq+0xad/0x160 request_threaded_irq+0xf5/0x160 ? xennet_tx_buf_gc+0x1d0/0x1d0 [xen_netfront] bind_evtchn_to_irqhandler+0x3d/0x70 ? xenbus_alloc_evtchn+0x41/0xa0 netback_changed+0xa46/0xcda [xen_netfront] ? find_watch+0x40/0x40 xenwatch_thread+0xc5/0x160 ? finish_wait+0x80/0x80 kthread+0x112/0x130 ? kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x35/0x40 Code: 81 5c 00 48 85 c0 75 cc 5b 49 89 2e 31 c0 5d 4d 89 3c 24 41 5c 41 5d 41 5e 41 5f c3 4c 89 ee 48 c7 c7 40 4f 0e b4 e8 65 ea d8 ff <0f> 0b b8 fe ff ff ff 5b 5d 41 5c 41 5d 41 5e 41 5f c3 66 0f 1f ---[ end trace 650e5561b0caab3a ]--- Signed-off-by:
Xiao Liang <xiliang@redhat.com> Reviewed-by:
-
Michael Müller authored
[ Upstream commit 0e7d4d93 ] This patch fixes two typos related to unregistering algorithms supported by SAHARAH 3. In sahara_register_algs the wrong algorithms are unregistered in case of an error. In sahara_unregister_algs the wrong array is used to determine the iteration count. Signed-off-by:
Michael Müller <michael@fds-team.de> Signed-off-by:
-
