- 24 Oct, 2019 40 commits
-
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header file related to media Drivers for Analog TV Tuners. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Sakari Ailus authored
Rename the confusingly named smiapp_update_mode() function as smiapp_pll_blanking_update(). The function is used to calculate new PLL and blanking configuration after binning or scaling configuration has been changed. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Sakari Ailus authored
Earlier it was possible that the parts of the driver that assumed runtime PM was enabled were being called before runtime PM was enabled in the driver's probe function. So enable runtime PM before registering the sub-device. Signed-off-by:
-
Sakari Ailus authored
Use non-binned limits when binning is disabled and binned when they're enabled. Signed-off-by:
-
Sakari Ailus authored
The sensor configuration since it was previously powered off was not changed, so no need to update the PLL configuration etc. What is necessary though is to re-apply the configuration to the sensor's registers. Signed-off-by:
-
Sakari Ailus authored
Only write the binning configuration at stream start. It has no effect otherwise. Signed-off-by:
-
Sakari Ailus authored
The driver implementation assumed the binning limits could change dynamically based on the binning configuration. This is not actually the case; these limits are static and suitable to be used with all binning configurations but possibly not optimal limit for many of those configurations. Signed-off-by:
-
Sakari Ailus authored
Destroy the mutex initialised by the driver in probe. Signed-off-by:
-
Sakari Ailus authored
The nokia,nvm-size property was used to tell the size of the NVM memory accessible through the sensor's register interface. However, while the size isn't directly readable through the sensor's register interface, it can be detected reading the NVM memory until the selected page is no longer available. Thus remove this property. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Sakari Ailus authored
The interface supports probing for the NVM size but this was not implemented in the driver. Do that now. This will also make nokia,nvm-size property redundant. Signed-off-by:
-
Sakari Ailus authored
Only some devices require polling for NVM ready. Do the polling only on devices that need it. Signed-off-by:
-
Sakari Ailus authored
The data transfer capability register was defined but its bits were not. Do that now. Signed-off-by:
-
Sakari Ailus authored
Split out reading a single NVM page into a separate function. Signed-off-by:
-
Sakari Ailus authored
If NVM reading failed, the device was left powered on. Fix that. Signed-off-by:
-
Sakari Ailus authored
The BIT macro is a better way to define register bits, for 1 << bit is risky for 32-bit registers. Also remove the definition of SMIAPP_DATA_TRANSFER_IF_1_CTRL_RD_EN which has a value of zero. Signed-off-by:
-
Chuhong Yuan authored
devm_regulator_get may return an error but mipi_csis_phy_init misses a check for it. This may lead to problems when regulator_set_voltage uses the unchecked pointer. This patch adds a check for devm_regulator_get to avoid potential risk. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Reviewed-by:
Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by:
-
Chuhong Yuan authored
mipid02_probe misses a check for devm_gpiod_get_optional and may miss the failure. Add a check to fix the problem. Signed-off-by:
-
Manivannan Sadhasivam authored
Add driver for Sony IMX290 CMOS image sensor driver. The driver only supports I2C interface for programming and MIPI CSI-2 for sensor output. [Sakari Ailus: Rewrapped a few lines over 80 chars a little.] Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
Manivannan Sadhasivam authored
Add devicetree binding for IMX290 CMOS image sensor. Let's also add MAINTAINERS entry for the binding and driver. Signed-off-by:
-
YueHaibing authored
If VIDEO_OV5695 is y and V4L2_FWNODE is m, building fails: drivers/media/i2c/ov5695.o: In function `ov5695_probe': ov5695.c:(.text+0xf4c): undefined reference to `v4l2_async_register_subdev_sensor_common' Select V4L2_FWNODE like OV5675 does. Fixes: 623df5d7 ("media: i2c: ov5695: Modify the function of async register subdev related devices") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Ricardo Ribalda Delgado authored
According to the datasheet, both AD5821 and AD5820 share a compatible register-set: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5821.pdf Some camera modules also refer that AD5823 is a replacement of AD5820: https://download.kamami.com/p564094-OV8865_DS.pdfSuggested-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Ricardo Ribalda Delgado <ribalda@kernel.org> Acked-by:
-
Ricardo Ribalda Delgado authored
Document new compatible devices. Cc: devicetree@vger.kernel.org Signed-off-by:
-
Ricardo Ribalda Delgado authored
Since kernel 4.16, i2c devices with DT compatible tag are modprobed using their DT modalias. Without this patch, if this driver is build as module it would never be autoprobed. There is no need to mask it with CONFIG_OF to allow ACPI loading, this also builds find with CONFIG_OF=n. Signed-off-by:
-
Ricardo Ribalda Delgado authored
This patch adds support for a programmable enable pin. It can be used in situations where the ANA-vcc is not configurable (dummy-regulator), or just to have a more fine control of the power saving. The use of the enable pin is optional. Signed-off-by:
-
Ricardo Ribalda Delgado authored
Document new enable-gpio field. It can be used to disable the part without turning down its regulator. Cc: devicetree@vger.kernel.org Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
-
Ricardo Ribalda Delgado authored
Without this patch, media_device_register_entity throws a warning: dev_warn(mdev->dev, "Entity type for entity %s was not initialized!\n", entity->name); Signed-off-by:
-
Benoit Parrot authored
The sensor data sheet clearly state that 2592x1944 only works at 15 fps make sure we don't try to miss configure the pll out of acceptable range. Signed-off-by:
Benoit Parrot <bparrot@ti.com> Reviewed-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Benoit Parrot authored
In the 1920x1080 register array an extra pair of reset ctrl disable re-enable was causing unwanted init delays. Signed-off-by:
-
Benoit Parrot authored
Add v4l2 controls to report the pixel rates of each mode. This is needed by some CSI2 receiver in order to perform proper DPHY configuration. Signed-off-by:
-
Colin Ian King authored
The variable rval is being initialized with a value that is never read and is being re-assigned a little later on. The assignment is redundant and hence can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Janusz Krzysztofik authored
A hardcoded 12 MHz master clock frequency has been assumed since conversion of the driver from soc_camera sensor to a standalone V4L2 subdevice by commit 23a52386 ("media: ov6650: convert to standalone v4l2 subdevice"). Fix it. Define a static table of supported master clock rates (fix misnamed symbol while being at it), then use v4l2_clk_get/set_rate() to obtain a clock rate matching one of those supported. On success, apply respective master clock hardware divisor provided by the matching element of the table. [Sakari Ailus: Initialize xclk to NULL.] Signed-off-by:
Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by:
-
Janusz Krzysztofik authored
This field of the driver private structure is no longer used, drop it. Signed-off-by:
-
Janusz Krzysztofik authored
As calculation of pixel clock hardware divisor no longer depends on mbus format specific maximum pixel clock, there is no need to reapply the divisor on format change. Drop related code from ov6650_s_fmt() helper. Since a master clock hardware divisor, so far applied only together with the pixel clock divisor in a single operation, will no longer be applied from ov6650_s_fmt(), apply it, still using a hardcoded value for now, from ov6650_prog_dflt() helper so hardware is still initialised correctly on device probe. Signed-off-by:
-
Janusz Krzysztofik authored
As appears from an analysis of to_clkrc() helper code after its pclk_limit argument has been dropped, its result no longer depends on another argument - pclk_max. Moreover, assuming that a constant value of FRAME_RATE_MAX is always used as a denominator of the only significant argument left - a struct v4l2_fract, the result in fact depends only on the numerator value of that argument. As a further consequence, it no longer makes sense to recalculate frame intervals by converting them forth and back with a GET_CLKRC_DIV(to_clkrc(tpf)) construct. Drop use of GET_CLKRC_DIV() on results of to_clkrc() where possible - use the frame interval value directly. Furthermore, replace the to_clkrc() helper function with a simple macro and update its users to always use FRAME_RATE_MAX as frame interval denominator and pass only its numerator as an argument. Signed-off-by:
-
Janusz Krzysztofik authored
That attribute used to be obtained from platform data by a soc_camera host interface and passed to the sensor driver for .s_mbus_fmt() video operation callback, later reused as .set_fmt() pad operation callback, to be able to limit frame rate. The driver stored that value in its private structure for further use from .g/s_parm(), later converted to g/s_frame_interval(). On conversion of the driver from soc_camera sensor to a standalone V4L2 subdevice by commit 23a52386 ("media: ov6650: convert to standalone v4l2 subdevice"), that attribute had been replaced by a constant and hardcoded to an arbitrarily chosen pixel clock limit. Drop it. Host interfaces can limit frame rate if needed by calling .s_frame_interval(). Signed-off-by:
-
Janusz Krzysztofik authored
The driver stores a frame interval value supposed to be in line with hardware state in a device private structure. Since the driver initial submission, the respective field of the structure has never been initialised on device probe. Moreover, if updated from .s_frame_interval(), a new value is stored before it is applied on hardware. If an error occurs during device update, the stored value may no longer reflect hardware state and consecutive calls to .g_frame_interval() may return incorrect information. Assuming a failed update of the device means its actual state hasn't changed, update the frame interval field of the device private structure with a new value only after it is successfully applied on hardware so it always reflects actual hardware state to the extent possible. Also, initialise the field with hardware default frame interval on device probe. Signed-off-by:
-
Sebastian Andrzej Siewior authored
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT. Both PREEMPT and PREEMPT_RT require the same functionality which today depends on CONFIG_PREEMPT. Switch the Kconfig dependency to CONFIG_PREEMPTION. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Alexandre Courbot authored
The request API documentation introduced a new section which should have been a subsection. Fix this. Signed-off-by:
Alexandre Courbot <acourbot@chromium.org> Signed-off-by:
Alexandre Courbot <gnurou@gmail.com> Signed-off-by:
-
Fabio Estevam authored
Pass the v4l2-ctl configuration for the imx6q-sabreauto PAL example for completeness and consistency. Suggested-by:
Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by:
Fabio Estevam <festevam@gmail.com> Acked-by:
-
Fabio Estevam authored
The i.MX6DL sabreauto has different numbering on the I2C bus and I2C muxes compared to the i.MX6Q as shown in the kernel log below: [ 5.159423] imx-media: ipu1_csi0_mux:5 -> ipu1_csi0:0 [ 5.164618] imx-media: ipu1_csi1_mux:5 -> ipu1_csi1:0 [ 5.169953] imx-media: adv7180 4-0021:0 -> ipu1_csi0_mux:4 To avoid confusion, add an entry that shows how to setup the links and configure the pads that are specific to the i.MX6DL sabreauto. Signed-off-by:
-
