Introduces routines that test whether a given network address is
equal to a node's own network address or if it lies within the node's
own network cluster, and which work properly regardless of whether
the node is using the default network address <0.0.0> or a non-zero
network address that is assigned later on. In essence, these routines
ensure that address <0.0.0> is treated as an alias for "this node",
regardless of which network address the node is actually using.

Old users of the pre-existing more strict match in_own_cluster()
have been accordingly redirected to what is now called
in_own_cluster_exact() --- which does not extend matching to <0,0,0>.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

No longer increments counter of number of publications by a node
if an attempt to add a new publication fails. This prevents TIPC from
incorrectly blocking future publications because the configured maximum
number of publications has been reached.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Ensures that node-scope name publications that exist prior to the
configuration of a node's network address are properly re-initialized
with that address when it is assigned. TIPC's node-scope publications
are now tracked using a publications list like the lists used for
cluster-scope and zone-scope publications so they can be easily updated
when required.

The inclusion of node scope name publications in a conventional publication
list means that they must now also be withdrawn, just like cluster and zone
scope publications are currently withdrawn.  So some conditional tests on
scope ==/!= TIPC_NODE_SCOPE are inserted/removed accordingly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Utilizes distinct lists to track zone-scope and cluster-scope names
published by a node. For now, TIPC continues to process the entries
in both lists in the same way; however, an upcoming patch will utilize
the existence of the lists to prevent the sending of cluster-scope names
to nodes that are not part of the local cluster.

To achieve this, an array of publication lists is introduced, so
that they can be iterated over and accessed via publ->scope as
an index where convenient.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

This is done so that it can be reused with differing publication
lists, instead of being hard coded to the cluster publicaton list.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

There is currently a single list that is containing both cluster-scope and
zone-scope publications, and the list count is a separate free floating
variable.  Create a struct to bind the count to the list, and to pave
the way for factoring out the publications into zone/cluster/node scope.

The current "publ_root" most matches what will be the cluster scope
list, so it is named accordingly in this commit.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: majianpeng <majianpeng@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver does not always use the same timing for what looks like
the same operations.

- DCR0
  Use the same udelay everywhere for reset. Upper bound is 100 us.
- DCR9
  Use 5us delay for srom clock. 1us delay for phy_write_1bit (writes
  PHY_DATA_[01]) are not changed as they stay withing a 2,5MHz MDIO
  clock range.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix mixed space and tabs.

Put bpf_jit_load_*[] externs into bpf_jit.h

"while(0)" --> "while (0)"
"COND (X)" --> "COND(X)"
Document branch offset calculations, and bpf_error's return
sequence.

Document the reason we need to emit three nops between the
%y register write and the divide instruction.

Remove erroneous trailing semicolons from emit_read_y() and
emit_write_y().

Based upon feedback from Sam Ravnborg.
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct conventions comments.  %o4 and %o5 were swapped,
%g3 was not documented.

Use r_TMP instead of r_SKB_DATA + r_OFF where possible in
assembler stubs.

Correct discussion of %o4 and %o5 in one of bpf_jit_compile()'s
comments.

Based upon feedback from Richard Mortimer.
Signed-off-by: David S. Miller <davem@davemloft.net>

Compared with previous chipsets, it needs no special action trough the
jumbo{enable/disable} helpers to operate with jumbo frames.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Put some settings of 8111f into one function which may be reused.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Hayes Wang <hayeswang@realtek.com>

New chipsets need it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>

Adjust r810x_pll_power_down, r810x_pll_power_up, and r8168_pll_power_up.
Always power up device during rtl_open. For r810x, turn off more power
when the WOL is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>

The new 84xx stopped flying below the radars.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Suggested by Hayes.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Fix printk format warning (from i386 build):

drivers/net/hippi/rrunner.c:146:9: warning: format '%08llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc:	linux-hippi@sunsite.dk
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch converts the drivers in drivers/net/can/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-can@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Make cgw_list static to remove the following sparse warning:
net/can/gw.c:69:1: warning: symbol 'cgw_list' was not declared.
Should it be static?
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Commit b82d1bb4 inadvertendly placed unrelated new code between
TCPCB_EVER_RETRANS and TCPCB_RETRANS and the other macros that refer
to the sacked field in the struct tcp_skb_cb (probably because there
was a misleading empty line there). This commit fixes up the
formatting so that all macros related to the sacked field are adjacent
again.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 109d2446

    "net/mlx4_en: Set max rate-limit for a TC"

introduced 64 bit math operations into mlx4_en_dcbnl_ieee_setmaxrate()

causing the following final link failure on an x86_32 allmodconfig

  ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko] undefined!

Convert it to use div_u64() instead.

Cc: Amir Vadai <amirv@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/atheros/atlx/atl1.c
	drivers/net/ethernet/atheros/atlx/atl1.h

Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds FDB bridge ops to the macvlan device passthru mode.
Additionally a flags field was added and a NOPROMISC bit to
allow users to use passthru mode without the driver calling
dev_set_promiscuity(). The flags field is a u16 placed in a
4 byte hole (consuming 2 bytes) of the macvlan_dev struct.

We want to do this so that the macvlan driver or stack
above the macvlan driver does not have to process every
packet. For the use case where we know all the MAC addresses
of the endstations above us this works well.

This patch is a result of Roopa Prabhu's work. Follow up
patches are needed for VEPA and VEB macvlan modes.

v2: Change from distinct nopromisc mode to a flags field to
    configure this. This avoids the tendency to add a new
    mode every time we need some slightly different behavior.
v3: fix error in dev_set_promiscuity and add change and get
    link attributes for flags.

CC: Roopa Prabhu <roprabhu@cisco.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The UTA table was being set to the functional equivalent of promiscuous
mode.  This was resulting in traffic from the virtual function being
flooded onto the wire and the PF device. This resulted in additional
overhead for VF traffic sent to the network and in the case of traffic
sent to the PF or another VF resulted in unwanted packets on the wire.

This was actually not the intended behavior. Now that we can program
the embedded switch correctly we can remove this snippit of code. Users
who want to support this should configure the FDB correctly using the
FDB ops.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows RAR table updates while in promiscuous. With
SR-IOV enabled it is valuable to allow the RAR table to
be updated even when in promisc mode to configure forwarding
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable FDB ops on ixgbe when in SR-IOV mode.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is useful to be able to monitor for FDB events in user space.
This patch adds support to generate netlink events when a change
is made to a device supporting the FDB ops.

This brings embedded switches inline with the SW net/bridge which
triggers events on FDB updates as well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a generic dump routine drivers can call. It
should be sufficient to handle any bridging model that
uses the unicast address list. This should be most SR-IOV
enabled NICs.

v2: return error on nlmsg_put and use -EMSGSIZE instead
    of -ENOMEM this is inline other usages
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a dev_uc_add_excl() and dev_mc_add_excl() calls
similar to the original dev_{uc|mc}_add() except it sets
the global bit and returns -EEXIST for duplicat entires.

This is useful for drivers that support SR-IOV, macvlan
devices and any other devices that need to manage the
unicast and multicast lists.

v2: fix typo UNICAST should be MULTICAST in dev_mc_add_excl()

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.

The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.

Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.

There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.

To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.

A basic setup with a SR-IOV enabled NIC looks like this,

          veth0  veth2
            |      |
          ------------
          |  bridge0 |   <---- software bridging
          ------------
               /
               /
  ethx.y      ethx
    VF         PF
     \         \          <---- propagate FDB entries to HW
     \         \
  --------------------
  |  Embedded Bridge |    <---- hardware offloaded switching
  --------------------

In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.

Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:

# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port    mac addr                flags
veth0   22:35:19:ac:60:58       static
veth0   9a:5f:81:f7:f6:ec       local
eth3    00:1b:21:55:23:59       local
eth3    22:35:19:ac:60:59       static
veth0   22:35:19:ac:60:57       static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port    mac addr                flags
veth0   22:35:19:ac:60:58       static
veth0   9a:5f:81:f7:f6:ec       local
eth3    00:1b:21:55:23:59       local
eth3    22:35:19:ac:60:59       static
veth0   22:35:19:ac:60:57       static
eth3    22:35:19:ac:60:59       local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3

I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.

[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
    http://patchwork.ozlabs.org/patch/117664/

Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.

v2: fixed api descriptions and error case with both NTF_SELF and
    NTF_MASTER set plus updated patch description.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent interrupts lost they should be dropped only if
they are scheduled via napi interfaces. In other case, there is
exists situation when napi handler process TX interrupt, stay in
RX processing and in that moment any other interrupt received.
Then before this patch TX bit in ISR will be cleaned, napi
schedule will not occur in case of currently processing event and
TX interrupt definitely will be lost.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the rx/tx handled inside napi handler, the cycle is
not needed now, because only the rx/tx need such kind of
processing.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unfortunately it is not clear from code is usage of
IMR register possible or not. So, to prevent possible
side-effects of reading this register i prefer store
interrupts enable flag separately.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>