A couple design choices were made here. First I use a new ring
pointer structure xdp_ring[] in the adapter struct instead of
pushing the newly allocated XDP TX rings into the tx_ring[]
structure. This means we have to duplicate loops around rings
in places we want to initialize both TX rings and XDP rings.
But by making it explicit it is obvious when we are using XDP
rings and when we are using TX rings. Further we don't have
to do ring arithmatic which is error prone. As a proof point
for doing this my first patches used only a single ring structure
and introduced bugs in FCoE code and macvlan code paths.

Second I am aware this is not the most optimized version of
this code possible. I want to get baseline support in using
the most readable format possible and then once this series
is included I will optimize the TX path in another series
of patches.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Basic XDP drop support for ixgbe. Uses READ_ONCE/xchg semantics on XDP
programs instead of RCU primitives as suggested by Daniel Borkmann and
Alex Duyck.

v2: fix the build issues seen w/ XDP when page sizes are larger than 4K
    and made minor fixes based on feedback from Jakub Kicinski
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent firmware change fixed an issue to acquire the PHY semaphore before
accessing PHY registers. This led to a case where  SW can issue a device
reset clearing the MDIO registers. This patch makes SW acquire the PHY
semaphore before issuing a device reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Daniel Borkmann says:

====================
Misc BPF updates

This set cleans up ldimm64 leftovers from early eBPF days and
adds couple of test cases related to this to the verifier test
suite. It also cleans up the kallsyms spinlock (had same patch
also in queue) by relaxing it through switching to _bh variant.
It fixes up test_progs in relation to htons/ntohs and adds
accessor macros for the percpu tests in test_maps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To overcome bugs as described and fixed in 89087c45 ("bpf: Fix
values type used in test_maps"), provide a generic BPF_DECLARE_PERCPU()
and bpf_percpu() accessor macro for all percpu map values used in
tests.

Declaring variables works as follows (also works for structs):

  BPF_DECLARE_PERCPU(uint32_t, my_value);

They can then be accessed normally as uint32_t type through:

  bpf_percpu(my_value, <cpu_nr>)

For example:

  bpf_percpu(my_value, 0)++;

Implicitly, we make sure that the passed type is allocated and aligned
by gcc at least on a 8-byte boundary, so that it works together with
the map lookup/update syscall for percpu maps. We use it as a usage
example in test_maps, so that others are free to adapt this into their
code when necessary.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dave reported that on sparc test_progs generates buggy swapped
eth->h_proto protocol comparisons:

  10: (15) if r3 == 0xdd86 goto pc+9
   R0=imm2,min_value=2,max_value=2 R1=pkt(id=0,off=0,r=14) R2=pkt_end R3=inv
   R4=pkt(id=0,off=14,r=14) R5=inv56 R10=fp

This is due to the unconditional ...

  #define htons __builtin_bswap16
  #define ntohs __builtin_bswap16

... in test_progs that causes this. Make use of asm/byteorder.h
and use __constant_htons() where possible and only perform the
bswap16 when on little endian in non-constant case.

Fixes: 6882804c ("selftests/bpf: add a test for overlapping packet range checks")
Fixes: 37821613 ("selftests/bpf: add l4 load balancer test based on sched_cls")
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hannes rightfully spotted that the bpf_lock doesn't need to be
irqsave variant. We never perform any such updates where this
would be necessary (neither right now nor in future), therefore
relax this further.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add several test cases around ldimm64, fp arithmetic and direct
packet access.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For both cases, the verifier is already rejecting such invalid
formed instructions. Thus, remove these artifacts from old times
and align it with ppc64, sparc64 and s390x JITs that don't have
them in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2017-04-28

Just one patch to fix a misplaced spin_unlock_bh in an error path.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2017-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Another set of patches for -next:
 * API support for concurrent scheduled scan requests
 * API changes for roaming reporting
 * BSS max idle support in mac80211
 * API changes for TX status reporting in mac80211
 * API changes for RX rate reporting in mac80211
 * rewrite monitor logic to prepare for BPF filters
 * bugfix for rare devices without 2.4 GHz support
 * a bugfix for recent DFS changes
 * some further cleanups

The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 6d684e54 ("rhashtable: Cap total number of entries
to 2^31") breaks rhashtable users that do not set max_size.  This
is because when max_size is zero max_elems is also incorrectly set
to zero instead of 2^31.

This patch fixes it by only lowering max_elems when max_size is not
zero.

Fixes: 6d684e54 ("rhashtable: Cap total number of entries to 2^31")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.

The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.

Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with  'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.

An example scenario is as below:

In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash  while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif

ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
	(Reason: 3=DEAUTH_LEAVING)

	WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
	[<bf77272c>] (sta_info_alloc [mac80211])
	[<bf78776c>] (ieee80211_add_station [mac80211]))
	[<bf73cc50>] (nl80211_new_station [cfg80211])

	Unable to handle kernel NULL pointer dereference at virtual
	address 00000014
	pgd = d5f4c000
	Internal error: Oops: 17 [#1] PREEMPT SMP ARM
	PC is at sta_info_alloc+0x380/0x3fc [mac80211]
	LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
	[<bf772738>] (sta_info_alloc [mac80211])
	[<bf78776c>] (ieee80211_add_station [mac80211])
	[<bf73cc50>] (nl80211_new_station [cfg80211]))

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.

As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.

Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[use C99 initializers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Makes further cleanups more readable
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack
struct ieee80211_tx_status instead of struct ieee80211_tx_info.

This struct can be used to pass extra information, e.g. for dynamic tx
power control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of hand-coding the bit manipulations, use the bitfield
macros to generate the code for the encoded bitrate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This field will need to be used again for HE, so rename it now.

Again, mostly done with this spatch:

@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We currently use a lot of flags that are mutually incompatible,
separate this out into actual encoding and bandwidth enum values.

Much of this again done with spatch, with manual post-editing,
mostly to add the switch statements and get rid of the conversions.

@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_80MHZ
+status->bw = RATE_INFO_BW_80
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_40MHZ
+status->bw = RATE_INFO_BW_40
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_20MHZ
+status->bw = RATE_INFO_BW_20
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_160MHZ
+status->bw = RATE_INFO_BW_160
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_5MHZ
+status->bw = RATE_INFO_BW_5
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_10MHZ
+status->bw = RATE_INFO_BW_10

@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_VHT
+status->encoding = RX_ENC_VHT
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_HT
+status->encoding = RX_ENC_HT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_VHT
+status.encoding = RX_ENC_VHT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_HT
+status.encoding = RX_ENC_HT

@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_HT)
+(status->encoding == RX_ENC_HT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_VHT)
+(status->encoding == RX_ENC_VHT)

@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_5MHZ)
+(status->bw == RATE_INFO_BW_5)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_10MHZ)
+(status->bw == RATE_INFO_BW_10)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_40MHZ)
+(status->bw == RATE_INFO_BW_40)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_80MHZ)
+(status->bw == RATE_INFO_BW_80)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_160MHZ)
+(status->bw == RATE_INFO_BW_160)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In preparation for adding support for HE rates, clean up
the driver report encoding for rate/bandwidth reporting
on RX frames.

Much of this patch was done with the following spatch:

@@
expression status;
@@
-status->flag & (RX_FLAG_HT | RX_FLAG_VHT)
+status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT)

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORTPRE
+status->enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status->flag & RX_FLAG_SHORTPRE
+status->enc_flags & RX_ENC_FLAG_SHORTPRE

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT
+status->enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status->flag & RX_FLAG_HT
+status->enc_flags & RX_ENC_FLAG_HT

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_40MHZ
+status->enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_40MHZ
+status->enc_flags & RX_ENC_FLAG_40MHZ

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORT_GI
+status->enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status->flag & RX_FLAG_SHORT_GI
+status->enc_flags & RX_ENC_FLAG_SHORT_GI

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT_GF
+status->enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status->flag & RX_FLAG_HT_GF
+status->enc_flags & RX_ENC_FLAG_HT_GF

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_VHT
+status->enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status->flag & RX_FLAG_VHT
+status->enc_flags & RX_ENC_FLAG_VHT

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_STBC_MASK
+status->enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status->flag & RX_FLAG_STBC_MASK
+status->enc_flags & RX_ENC_FLAG_STBC_MASK

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_LDPC
+status->enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status->flag & RX_FLAG_LDPC
+status->enc_flags & RX_ENC_FLAG_LDPC

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_10MHZ
+status->enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_10MHZ
+status->enc_flags & RX_ENC_FLAG_10MHZ

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_5MHZ
+status->enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_5MHZ
+status->enc_flags & RX_ENC_FLAG_5MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_80MHZ
+status->enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_80MHZ
+status->enc_flags & RX_ENC_FLAG_80MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_160MHZ
+status->enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_160MHZ
+status->enc_flags & RX_ENC_FLAG_160MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_BF
+status->enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_BF
+status->enc_flags & RX_ENC_FLAG_BF

@@
assignment operator op;
expression status, STBC;
@@
-status->flag op STBC << RX_FLAG_STBC_SHIFT
+status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORTPRE
+status.enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status.flag & RX_FLAG_SHORTPRE
+status.enc_flags & RX_ENC_FLAG_SHORTPRE

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT
+status.enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status.flag & RX_FLAG_HT
+status.enc_flags & RX_ENC_FLAG_HT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_40MHZ
+status.enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_40MHZ
+status.enc_flags & RX_ENC_FLAG_40MHZ

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORT_GI
+status.enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status.flag & RX_FLAG_SHORT_GI
+status.enc_flags & RX_ENC_FLAG_SHORT_GI

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT_GF
+status.enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status.flag & RX_FLAG_HT_GF
+status.enc_flags & RX_ENC_FLAG_HT_GF

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_VHT
+status.enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status.flag & RX_FLAG_VHT
+status.enc_flags & RX_ENC_FLAG_VHT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_STBC_MASK
+status.enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status.flag & RX_FLAG_STBC_MASK
+status.enc_flags & RX_ENC_FLAG_STBC_MASK

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_LDPC
+status.enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status.flag & RX_FLAG_LDPC
+status.enc_flags & RX_ENC_FLAG_LDPC

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_10MHZ
+status.enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_10MHZ
+status.enc_flags & RX_ENC_FLAG_10MHZ

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_5MHZ
+status.enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_5MHZ
+status.enc_flags & RX_ENC_FLAG_5MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_80MHZ
+status.enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_80MHZ
+status.enc_flags & RX_ENC_FLAG_80MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_160MHZ
+status.enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_160MHZ
+status.enc_flags & RX_ENC_FLAG_160MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_BF
+status.enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_BF
+status.enc_flags & RX_ENC_FLAG_BF

@@
assignment operator op;
expression status, STBC;
@@
-status.flag op STBC << RX_FLAG_STBC_SHIFT
+status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT

@@
@@
-RX_FLAG_STBC_SHIFT
+RX_ENC_FLAG_STBC_SHIFT
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge tag 'wireless-drivers-next-for-davem-2017-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.12

Few remaining patches for 4.12 submitted during the last week.

Major changes:

iwlwifi

* the firmware for 7265D and 3168 NICs is frozen at version 29

* more support for the upcoming A000 series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: PTP enhancements.

The patch series contains set of enhancements for qed/qede ptp
implementation.
Patches (1)-(3) adds resource locking implementation to allow
PTP functionality only on the first detected ethernet PF of the port.
The change is required as the adapter currently supports only one
instance of the PTP client on a given port.
Patch (4) removes the un-needed header file.
Patch (5) moves the ptt-lock get/release logic to the ptp specific
code.

Please consider applying this series to "net-next" branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the code for acquiring/releasing ptt_ptp lock to ptp specific
implementations i.e., ptp_enable()/disable() respectively.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch deletes the qed_ptp.h file which is not required.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds necessary changes to the driver to use qed resource
locking functionality. Currently the ptp initialization is spread
between driver probe/open implementations, associated APIs are
qede_ptp_register_phc()/qede_ptp_start(). Clubbed this functionality
into single API qed_ptp_enable() to simplify the usage of qed resource
locking implementation. The new API will be invoked in the probe path.
Similarly the ptp clean-up code is moved to qede_ptp_disable() which
gets invoked in the driver unload path.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support for per-port resource lock in favour of PTP.
PTP module acquires/releases the MFW resource lock while enabling/
disabling the PTP on the interface. The PF instance which has the
ownership of this resource lock will get the exclusive access to the
PTP clock functionality on the port.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds API for default initialization of the MFW resource
locking.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moving the loopback into a VRF breaks networking for the default VRF.
Since the VRF device is the loopback for VRF domains, there is no
reason to move the loopback. Given the repercussions, block attempts
to set lo into a VRF.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return error code -EINVAL from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 622ec2c9 ("net: core: add UID to flows, rules, and routes")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support for l2 multicast flood control was added in commit b6cb5ac8
("net: bridge: add per-port multicast flood flag"). It allows broadcast
as it was introduced specifically for unknown multicast flood control.
But as broadcast is a special case of multicast, this may also need to
be disabled. For this purpose, introduce a flag to disable the flooding
of received l2 broadcasts. This approach is backwards compatible and
provides flexibility in filtering for the desired packet types.

Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Mike Manning <mmanning@brocade.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The func fib_flush already flushes the rt cache if necessary, so it
is not necessary to invoke rt_cache_flush again in fib_disable_ip.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need to verify that cfg->ifname is unique at this point.
register_netdev() will return -EEXIST if asked to create a device with
a name that's alrealy in use.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since netif_carrier_on() will do nothing if device's carrier is already
on, so it's unnecessary to do carrier status check.

It's the same for netif_carrier_off().
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the comment for netif_dormant() function to reflect
the intended usage.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add option to xdp1 and xdp_tx_iptunnel to insert xdp program in
SKB_MODE:
 - update set_link_xdp_fd to take a flags argument that is added to the
   RTM_SETLINK message

 - Add -S option to xdp1 and xdp_tx_iptunnel user code. When passed in
   XDP_FLAGS_SKB_MODE is set in the flags arg passed to set_link_xdp_fd
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When max_size is not set or if it set to a sufficiently large
value, the nelems counter can overflow.  This would cause havoc
with the automatic shrinking as it would then attempt to fit a
huge number of entries into a tiny hash table.

This patch fixes this by adding max_elems to struct rhashtable
to cap the number of elements.  This is set to 2^31 as nelems is
not a precise count.  This is sufficiently smaller than UINT_MAX
that it should be safe.

When max_size is set max_elems will be lowered to at most twice
max_size as is the status quo.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

I wrongly assumed tp->tcp_mstamp was up to date at the time
tcp_rack_reo_timeout() was called.

It is not true, since we only update tcp->tcp_mstamp when receiving
a packet (as initially done in commit 69e996c5 ("tcp: add
tp->tcp_mstamp field")

tcp_rack_reo_timeout() being called by a timer and not an incoming
packet, we need to refresh tp->tcp_mstamp

Fixes: 7c1c7308 ("tcp: do not pass timestamp to tcp_rack_detect_loss()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>