Let general purpose I2C/SMBus bus drivers add SPD to their class. Once
this is done, we will be able to tell the eeprom driver to only probe
for SPD EEPROMs and similar on these buses.

Note that I took a conservative approach here, adding I2C_CLASS_SPD to
many drivers that have no idea whether they can host SPD EEPROMs or not.
This is to make sure that the eeprom driver doesn't stop probing buses
where SPD EEPROMs or equivalent live.

So, bus driver maintainers and users should feel free to remove the SPD
class from drivers those buses never have SPD EEPROMs or they don't
want the eeprom driver to bind to them. Likewise, feel free to add the
SPD class to any bus driver I might have missed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Let framebuffer drivers set their I2C bus class to DDC. Once this is
done, we will be able to tell the eeprom driver to only probe for
EDID EEPROMs on these buses.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Bugfixes to the i2c-cpm driver

- enable correct interrupts (I2CER_TXE instead of I2CER_BUSY)
- replace forgotten iic with i2c
- prefix debug-output on init with 0x and add frequency
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This driver uses the port of 2.4 code from Vitaly Bordug
<vitb@kernel.crashing.org> and the actual algorithm used by the i2c
driver of the DBox code on cvs.tuxboc.org from Felix Domke
(tmbinc@gmx.net) and Gillem (htoa@gmx.net) converted to an
of_platform_driver. Tested on CPM1 (MPC823 on dbox2 hardware) and
CPM2 (MPC8272).
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This is part of the effort to get rid of the BKL.

[JD: In fact i2c-dev doesn't need more locking than is already done
for the other i2c drivers, so we can simply switch to unlocked_ioctl.]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

New i2c bus driver for the Intel SCH chipsets (AF82US15W, AF82US15L,
AF82UL11L).
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c_del_driver() can be simplified a bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Use list_for_each_entry_safe() in i2c_del_adapter() and i2c_del_driver().
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Fix errorcode to be more descriptive when ioremap fails.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Give a more concrete error code, when the bus is not idle.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Many PC SMBus host controller drivers don't properly handle the case
where they are requested to achieve a transaction they do not support.
Update them so that the consistently print a warning message and
return a single error value in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The i2c-piix4 driver was used recently as a model to write a new SMBus
host controller driver and this made me realize that the code of this
old driver wasn't exactly good. So, here are many cleanups and minor
fixes to this driver, so that these minor mistakes aren't duplicated
again:

* Delete unused structure.
* Delete needless forward function declaration.
* Properly announce the SMBus host controller as we find it.
* Spell it SMBus not SMB.
* Return -EBUSY instead of -ENODEV when the I/O region is already in
  use.
* Drop useless masks on the 7-bit address and the R/W bit.
* Reject block transaction requests with an invalid block length.
* Check and report block transaction replies with an invalid block
  length.
* Delete a useless comment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM").  Build tested, with eyeball
review.

One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Defend the i2c refcount calls against NULL pointers, as is important
(and conventional) for such calls.  Note that none of the current
callers of i2c_use_client() use its return value.

[JD: I hate this but apparently all the other subsystems do it so...]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Provide kerneldoc for most of the I2C and SMBus I/O calls.  Add a
comment summarizing some fault reporting issues which affect the
ability to provide clean fault reports through I2C master transfer
calls.  (Making it hard to precisely specify their return values...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

That function is actually named i2c_smbus_xfer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Function i2c_smbus_write_quick has no users left, so we can delete it.

Also update the list of these helper functions which are gone but
could be added back if needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The list of I2C/SMBus bus drivers is growing and it is sometimes
difficult for the users to figure out what drivers they should enable.
By grouping the drivers by type, I hope to make the selection easier.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

More updates to the I2C stack's fault reporting:  make the core stop
returning "-1" (usually "-EPERM") for all faults.  Instead, pass lower
level fault code up the stack, or return some appropriate errno.

This patch happens to touch almost exclusively SMBus calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-core doesn't use seq files, so doesn't need to include
<linux/seq_file.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Create Documentation/i2c/fault-codes to help standardize
fault/error code usage in the I2C stack.  It turns out that
returning -1 (-EPERM) for everything was not at all helpful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Since only a few Blackfins lack TWI, just list them in a depends
statement.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This patch contains the scheduled removal of i2c-i810, i2c-prosavage
and i2c-savage4.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Just like the Tyan S4882, the S4985 uses a multiplexer to give access
to all 16 memory module SPD EEPROMs. This specific i2c-nforce2-s4985
driver adds support for this. It is heavily based on the older
i2c-amd756-s4882 driver.

As more mainboards will use multiplexer chips, we will have to find a
way to support them without having to write a new specfic driver for
each. The recent changes to the i2c subsystem should help us, and the
new gpio subsystem might help, too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

If an interrupt happens before an I2c master read/write,
complete is called on uninitialized structure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

If wait_for_completion_interruptible_timeout exits due
to a signal, the i2c bus was locking up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Interrupts are enabled at the point where the DAVINCI_I2C_IVR_REG is read,
so unless an interrupt happened just at that moment, no interrupt would be
pending. Even though documentation implies you should do this, I see no
reason. If slave support is added, this read would cause a hard to
reproduce bug.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Previously the dev_dbg only printed if no error.
Printing also on an error is more useful
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Ensure psc value gives a clock between 7-12 MHz
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Use class_for_each_device for iteration.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

 # cat devices.list
 c 1:3 r
 # echo 'c 1:3 w' > sub/devices.allow
 # cat sub/devices.list
 c 1:3 w

As illustrated, the parent group has no write permission to /dev/null, so
it's child should not be allowed to add this write permission.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

 # echo "b $((0x7fffffff)):$((0x80000000)) rwm" > devices.allow
 # cat devices.list
 b 214748364:-21474836 rwm

though a major/minor number of 0x800000000 is meaningless, we
should not cast it to a negative value.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  cpusets, hotplug, scheduler: fix scheduler domain breakage

Commit f18f982a ("sched: CPU hotplug events must not destroy scheduler
domains created by the cpusets") introduced a hotplug-related problem as
described below:

Upon CPU_DOWN_PREPARE,

  update_sched_domains() -> detach_destroy_domains(&cpu_online_map)

does the following:

/*
 * Force a reinitialization of the sched domains hierarchy. The domains
 * and groups cannot be updated in place without racing with the balancing
 * code, so we temporarily attach all running cpus to the NULL domain
 * which will prevent rebalancing while the sched domains are recalculated.
 */

The sched-domains should be rebuilt when a CPU_DOWN ops. has been
completed, effectively either upon CPU_DEAD{_FROZEN} (upon success) or
CPU_DOWN_FAILED{_FROZEN} (upon failure -- restore the things to their
initial state). That's what update_sched_domains() also does but only
for !CPUSETS case.

With f18f982a, sched-domains' reinitialization is delegated to
CPUSETS code:

cpuset_handle_cpuhp() -> common_cpu_mem_hotplug_unplug() ->
rebuild_sched_domains()

Being called for CPU_UP_PREPARE and if its callback is called after
update_sched_domains()), it just negates all the work done by
update_sched_domains() -- i.e. a soon-to-be-offline cpu is included in
the sched-domains and that makes it visible for the load-balancer
while the CPU_DOWN ops. is in progress.

__migrate_live_tasks() moves the tasks off a 'dead' cpu (it's already
"offline" when this function is called).

try_to_wake_up() is called for one of these tasks from another CPU ->
the load-balancer (wake_idle()) picks up a "dead" CPU and places the
task on it. Then e.g. BUG_ON(rq->nr_running) detects this a bit later
-> oops.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Paul Menage <menage@google.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: miaox@cn.fujitsu.com
Cc: rostedt@goodmis.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: fix ldt limit for 64 bit

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] bsg: fix oops on remove
  [SCSI] fusion: default MSI to disabled for SPI and FC controllers
  [SCSI] ipr: Fix HDIO_GET_IDENTITY oops for SATA devices
  [SCSI] mptspi: fix oops in mptspi_dv_renegotiate_work()
  [SCSI] erase invalid data returned by device

The current definition of wksidarr works fine on little endian arches
(since cpu_to_le32 is a no-op there), but on big-endian arches, it fails
to compile with this error:

error: braced-group within expression allowed only inside a function

The problem is that this static declaration has cpu_to_le32 embedded
within it, and that expands into a function macro.  We need to use
__constant_cpu_to_le32() instead.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>