- 24 Oct, 2019 4 commits
-
-
Alain Volmat authored
Remove the following warning: drivers/i2c/busses/i2c-stm32f7.c:315: warning: cannot understand function prototype: 'struct stm32f7_i2c_spec i2c_specs[] = Replace a comment starting with /** by simply /* to avoid having it interpreted as a kernel-doc comment. Fixes: aeb068c5 ("i2c: i2c-stm32f7: add driver") Signed-off-by:
Alain Volmat <alain.volmat@st.com> Reviewed-by:
Pierre-Yves MORDRET <pierre-yves.mordret@st.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de>
-
Fabrice Gasnier authored
When in slave mode, an arbitration loss (ARLO) may be detected before the slave had a chance to detect the stop condition (STOPF in ISR). This is seen when two master + slave adapters switch their roles. It provokes the i2c bus to be stuck, busy as SCL line is stretched. - the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag remains set until next master xfer (e.g. when STOPIE irq get unmasked). In this case, completion is generated too early: immediately upon new transfer request (then it doesn't send all data). - Some data get stuck in TXDR register. As a consequence, the controller stretches the SCL line: the bus gets busy until a future master transfer triggers the bus busy / recovery mechanism (this can take time... and may never happen at all) So choice is to let the STOPF being detected by the slave isr handler, to properly handle this stop condition. E.g. don't mask IRQs in error handler, when the slave is running. Fixes: 60d609f3 ("i2c: i2c-stm32f7: Add slave support") Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by:
-
Fabrice Gasnier authored
The slave-interface documentation [1] states "the bus driver should transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event: - 'val': backend returns first byte to be sent The driver currently ignores the 1st byte to send on this event. [1] https://www.kernel.org/doc/Documentation/i2c/slave-interface Fixes: 60d609f3 ("i2c: i2c-stm32f7: Add slave support") Signed-off-by:
-
Fabien Parent authored
Since commit abf4923e ("i2c: mediatek: disable zero-length transfers for mt8183"), there is a NULL pointer dereference for all the SoCs that don't have any quirk. mtk_i2c_functionality is not checking that the quirks pointer is not NULL before starting to use it. This commit add a call to i2c_check_quirks which will check whether the quirks pointer is set, and if so will check if the IP has the NO_ZERO_LEN quirk. Fixes: abf4923e ("i2c: mediatek: disable zero-length transfers for mt8183") Signed-off-by:
Fabien Parent <fparent@baylibre.com> Reviewed-by:
Cengiz Can <cengiz@kernel.wtf> Reviewed-by:
Hsin-Yi Wang <hsinyi@chromium.org> Tested-by:
Ulrich Hecht <uli@fpond.eu> Signed-off-by:
-
- 21 Oct, 2019 1 commit
-
-
Jae Hyun Yoo authored
In case of master pending state, it should not trigger a master command, otherwise data could be corrupted because this H/W shares the same data buffer for slave and master operations. It also means that H/W command queue handling is unreliable because of the buffer sharing issue. To fix this issue, it clears command queue if a master command is queued in pending state to use S/W solution instead of H/W command queue handling. Also, it refines restarting mechanism of the pending master command. Fixes: 2e57b7ce ("i2c: aspeed: Add multi-master use case support") Signed-off-by:
Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by:
Brendan Higgins <brendanhiggins@google.com> Acked-by:
Joel Stanley <joel@jms.id.au> Tested-by:
Tao Ren <taoren@fb.com> Signed-off-by:
-
- 20 Oct, 2019 6 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
Merge tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull more Kbuild fixes from Masahiro Yamada: - fix a bashism of setlocalversion - do not use the too new --sort option of tar * tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kheaders: substituting --sort in archive creation scripts: setlocalversion: fix a bashism kbuild: update comment about KBUILD_ALLDIRS
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A small set of x86 fixes: - Prevent a NULL pointer dereference in the X2APIC code in case of a CPU hotplug failure. - Prevent boot failures on HP superdome machines by invalidating the level2 kernel pagetable entries outside of the kernel area as invalid so BIOS reserved space won't be touched unintentionally. Also ensure that memory holes are rounded up to the next PMD boundary correctly. - Enable X2APIC support on Hyper-V to prevent boot failures. - Set the paravirt name when running on Hyper-V for consistency - Move a function under the appropriate ifdef guard to prevent build warnings" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/boot/acpi: Move get_cmdline_acpi_rsdp() under #ifdef guard x86/hyperv: Set pv_info.name to "Hyper-V" x86/apic/x2apic: Fix a NULL pointer deref when handling a dying cpu x86/hyperv: Make vapic support x2apic mode x86/boot/64: Round memory hole size up to next PMD page x86/boot/64: Make level2_kernel_pgt pages invalid outside kernel area -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "A small set of irq chip driver fixes and updates: - Update the SIFIVE PLIC interrupt driver to use the fasteoi handler to address the shortcomings of the existing flow handling which was prone to lose interrupts - Use the proper limit for GIC interrupt line numbers - Add retrigger support for the recently merged Anapurna Labs Fabric interrupt controller to make it complete - Enable the ATMEL AIC5 interrupt controller driver on the new SAM9X60 SoC" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/sifive-plic: Switch to fasteoi flow irqchip/gic-v3: Fix GIC_LINE_NR accessor irqchip/atmel-aic5: Add support for sam9x60 irqchip irqchip/al-fic: Add support for irq retrigger -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull hrtimer fixlet from Thomas Gleixner: "A single commit annotating the lockcless access to timer->base with READ_ONCE() and adding the WRITE_ONCE() counterparts for completeness" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: hrtimer: Annotate lockless access to timer->base
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull stop-machine fix from Thomas Gleixner: "A single fix, amending stop machine with WRITE/READ_ONCE() to address the fallout of KCSAN" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: stop_machine: Avoid potential race behaviour
-
- 19 Oct, 2019 29 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: "I was battling a cold after some recent trips, so quite a bit piled up meanwhile, sorry about that. Highlights: 1) Fix fd leak in various bpf selftests, from Brian Vazquez. 2) Fix crash in xsk when device doesn't support some methods, from Magnus Karlsson. 3) Fix various leaks and use-after-free in rxrpc, from David Howells. 4) Fix several SKB leaks due to confusion of who owns an SKB and who should release it in the llc code. From Eric Biggers. 5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet. 6) Jumbo packets don't work after resume on r8169, as the BIOS resets the chip into non-jumbo mode during suspend. From Heiner Kallweit. 7) Corrupt L2 header during MPLS push, from Davide Caratti. 8) Prevent possible infinite loop in tc_ctl_action, from Eric Dumazet. 9) Get register bits right in bcmgenet driver, based upon chip version. From Florian Fainelli. 10) Fix mutex problems in microchip DSA driver, from Marek Vasut. 11) Cure race between route lookup and invalidation in ipv4, from Wei Wang. 12) Fix performance regression due to false sharing in 'net' structure, from Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits) net: reorder 'struct net' fields to avoid false sharing net: dsa: fix switch tree list net: ethernet: dwmac-sun8i: show message only when switching to promisc net: aquantia: add an error handling in aq_nic_set_multicast_list net: netem: correct the parent's backlog when corrupted packet was dropped net: netem: fix error path for corrupted GSO frames macb: propagate errors when getting optional clocks xen/netback: fix error path of xenvif_connect_data() net: hns3: fix mis-counting IRQ vector numbers issue net: usb: lan78xx: Connect PHY before registering MAC vsock/virtio: discard packets if credit is not respected vsock/virtio: send a credit update when buffer size is changed mlxsw: spectrum_trap: Push Ethernet header before reporting trap net: ensure correct skb->tstamp in various fragmenters net: bcmgenet: reset 40nm EPHY on energy detect net: bcmgenet: soft reset 40nm EPHYs before MAC init net: phy: bcm7xxx: define soft_reset for 40nm EPHY net: bcmgenet: don't set phydev->link from MAC net: Update address for MediaTek ethernet driver in MAINTAINERS ipv4: fix race condition between route lookup and invalidation ... -
Eric Dumazet authored
Intel test robot reported a ~7% regression on TCP_CRR tests that they bisected to the cited commit. Indeed, every time a new TCP socket is created or deleted, the atomic counter net->count is touched (via get_net(net) and put_net(net) calls) So cpus might have to reload a contended cache line in net_hash_mix(net) calls. We need to reorder 'struct net' fields to move @hash_mix in a read mostly cache line. We move in the first cache line fields that can be dirtied often. We probably will have to address in a followup patch the __randomize_layout that was added in linux-4.13, since this might break our placement choices. Fixes: 355b9855 ("netns: provide pure entropy for net_hash_mix()") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
kernel test robot <oliver.sang@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
If there are multiple switch trees on the device, only the last one will be listed, because the arguments of list_add_tail are swapped. Fixes: 83c0afae ("net: dsa: Add new binding implementation") Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Mans Rullgard authored
Printing the info message every time more than the max number of mac addresses are requested generates unnecessary log spam. Showing it only when the hw is not already in promiscous mode is equally informative without being annoying. Signed-off-by:
Mans Rullgard <mans@mansr.com> Signed-off-by:
-
Chenwandun authored
add an error handling in aq_nic_set_multicast_list, it may not work when hw_multicast_list_set error; and at the same time it will remove gcc Wunused-but-set-variable warning. Signed-off-by:
Chenwandun <chenwandun@huawei.com> Reviewed-by:
Igor Russkikh <igor.russkikh@aquantia.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== net: netem: fix further issues with packet corruption This set is fixing two more issues with the netem packet corruption. First patch (which was previously posted) avoids NULL pointer dereference if the first frame gets freed due to allocation or checksum failure. v2 improves the clarity of the code a little as requested by Cong. Second patch ensures we don't return SUCCESS if the frame was in fact dropped. Thanks to this commit message for patch 1 no longer needs the "this will still break with a single-frame failure" disclaimer. ==================== Signed-off-by: -
Jakub Kicinski authored
If packet corruption failed we jump to finish_segs and return NET_XMIT_SUCCESS. Seeing success will make the parent qdisc increment its backlog, that's incorrect - we need to return NET_XMIT_DROP. Fixes: 6071bd1a ("netem: Segment GSO packets on enqueue") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
To corrupt a GSO frame we first perform segmentation. We then proceed using the first segment instead of the full GSO skb and requeue the rest of the segments as separate packets. If there are any issues with processing the first segment we still want to process the rest, therefore we jump to the finish_segs label. Commit 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames") started using the pointer to the first segment in the "rest of segments processing", but as mentioned above the first segment may had already been freed at this point. Backlog corrections for parent qdiscs have to be adjusted. Fixes: 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames") Reported-by:
kbuild test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Michael Tretter authored
The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver marks clock as not available if it receives an error when trying to get a clock. This is wrong, because a clock controller might return -EPROBE_DEFER if a clock is not available, but will eventually become available. In these cases, the driver would probe successfully but will never be able to adjust the clocks, because the clocks were not available during probe, but became available later. For example, the clock controller for the ZynqMP is implemented in the PMU firmware and the clocks are only available after the firmware driver has been probed. Use devm_clk_get_optional() in instead of devm_clk_get() to get the optional clock and propagate all errors to the calling function. Signed-off-by:
Michael Tretter <m.tretter@pengutronix.de> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Tested-by:
-
Juergen Gross authored
xenvif_connect_data() calls module_put() in case of error. This is wrong as there is no related module_get(). Remove the superfluous module_put(). Fixes: 279f438e ("xen-netback: Don't destroy the netdev until the vif is shut down") Cc: <stable@vger.kernel.org> # 3.12 Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Paul Durrant <paul@xen.org> Reviewed-by:
Wei Liu <wei.liu@kernel.org> Signed-off-by:
-
Yonglong Liu authored
Currently, the num_msi_left means the vector numbers of NIC, but if the PF supported RoCE, it contains the vector numbers of NIC and RoCE(Not expected). This may cause interrupts lost in some case, because of the NIC module used the vector resources which belongs to RoCE. This patch adds a new variable num_nic_msi to store the vector numbers of NIC, and adjust the default TQP numbers and rss_size according to the value of num_nic_msi. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Linus Torvalds authored
Merge misc fixes from Andrew Morton: "Rather a lot of fixes, almost all affecting mm/" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits) scripts/gdb: fix debugging modules on s390 kernel/events/uprobes.c: only do FOLL_SPLIT_PMD for uprobe register mm/thp: allow dropping THP from page cache mm/vmscan.c: support removing arbitrary sized pages from mapping mm/thp: fix node page state in split_huge_page_to_list() proc/meminfo: fix output alignment mm/init-mm.c: include <linux/mman.h> for vm_committed_as_batch mm/filemap.c: include <linux/ramfs.h> for generic_file_vm_ops definition mm: include <linux/huge_mm.h> for is_vma_temporary_stack zram: fix race between backing_dev_show and backing_dev_store mm/memcontrol: update lruvec counters in mem_cgroup_move_account ocfs2: fix panic due to ocfs2_wq is null hugetlbfs: don't access uninitialized memmaps in pfn_range_valid_gigantic() mm: memblock: do not enforce current limit for memblock_phys* family mm: memcg: get number of pages on the LRU list in memcgroup base on lru_zone_size mm/gup: fix a misnamed "write" argument, and a related bug mm/gup_benchmark: add a missing "w" to getopt string ocfs2: fix error handling in ocfs2_setattr() mm: memcg/slab: fix panic in __free_slab() caused by premature memcg pointer release mm/memunmap: don't access uninitialized memmap in memunmap_pages() ...
-
Ilya Leoshkevich authored
Currently lx-symbols assumes that module text is always located at module->core_layout->base, but s390 uses the following layout: +------+ <- module->core_layout->base | GOT | +------+ <- module->core_layout->base + module->arch->plt_offset | PLT | +------+ <- module->core_layout->base + module->arch->plt_offset + | TEXT | module->arch->plt_size +------+ Therefore, when trying to debug modules on s390, all the symbol addresses are skewed by plt_offset + plt_size. Fix by adding plt_offset + plt_size to module_addr in load_module_symbols(). Link: http://lkml.kernel.org/r/20191017085917.81791-1-iii@linux.ibm.comSigned-off-by:
Ilya Leoshkevich <iii@linux.ibm.com> Reviewed-by:
Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Song Liu authored
Attaching uprobe to text section in THP splits the PMD mapped page table into PTE mapped entries. On uprobe detach, we would like to regroup PMD mapped page table entry to regain performance benefit of THP. However, the regroup is broken For perf_event based trace_uprobe. This is because perf_event based trace_uprobe calls uprobe_unregister twice on close: first in TRACE_REG_PERF_CLOSE, then in TRACE_REG_PERF_UNREGISTER. The second call will split the PMD mapped page table entry, which is not the desired behavior. Fix this by only use FOLL_SPLIT_PMD for uprobe register case. Add a WARN() to confirm uprobe unregister never work on huge pages, and abort the operation when this WARN() triggers. Link: http://lkml.kernel.org/r/20191017164223.2762148-6-songliubraving@fb.com Fixes: 5a52c9df ("uprobe: use FOLL_SPLIT_PMD instead of FOLL_SPLIT") Signed-off-by:
Song Liu <songliubraving@fb.com> Reviewed-by:
Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: William Kucharski <william.kucharski@oracle.com> Cc: Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by:
-
Kirill A. Shutemov authored
Once a THP is added to the page cache, it cannot be dropped via /proc/sys/vm/drop_caches. Fix this issue with proper handling in invalidate_mapping_pages(). Link: http://lkml.kernel.org/r/20191017164223.2762148-5-songliubraving@fb.com Fixes: 99cb0dbd ("mm,thp: add read-only THP support for (non-shmem) FS") Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
Yang Shi <yang.shi@linux.alibaba.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by:
-
William Kucharski authored
__remove_mapping() assumes that pages can only be either base pages or HPAGE_PMD_SIZE. Ask the page what size it is. Link: http://lkml.kernel.org/r/20191017164223.2762148-4-songliubraving@fb.com Fixes: 99cb0dbd ("mm,thp: add read-only THP support for (non-shmem) FS") Signed-off-by:
William Kucharski <william.kucharski@oracle.com> Signed-off-by:
Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by:
-
Kirill A. Shutemov authored
Make sure split_huge_page_to_list() handles the state of shmem THP and file THP properly. Link: http://lkml.kernel.org/r/20191017164223.2762148-3-songliubraving@fb.com Fixes: 60fbf0ab ("mm,thp: stats for file backed THP") Signed-off-by:
-
Kirill A. Shutemov authored
Patch series "Fixes for THP in page cache", v2. This patch (of 5): Add extra space for FileHugePages and FilePmdMapped, so the output is aligned with other rows. Link: http://lkml.kernel.org/r/20191017164223.2762148-2-songliubraving@fb.com Fixes: 60fbf0ab ("mm,thp: stats for file backed THP") Signed-off-by:
-
Ben Dooks (Codethink) authored
mm_init.c needs to include <linux/mman.h> for the definition of vm_committed_as_batch. Fixes the following sparse warning: mm/mm_init.c:141:5: warning: symbol 'vm_committed_as_batch' was not declared. Should it be static? Link: http://lkml.kernel.org/r/20191016091509.26708-1-ben.dooks@codethink.co.ukSigned-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by:
-
Ben Dooks authored
The generic_file_vm_ops is defined in <linux/ramfs.h> so include it to fix the following warning: mm/filemap.c:2717:35: warning: symbol 'generic_file_vm_ops' was not declared. Should it be static? Link: http://lkml.kernel.org/r/20191008102311.25432-1-ben.dooks@codethink.co.ukSigned-off-by:
-
Ben Dooks authored
Include <linux/huge_mm.h> for the definition of is_vma_temporary_stack to fix the following sparse warning: mm/rmap.c:1673:6: warning: symbol 'is_vma_temporary_stack' was not declared. Should it be static? Link: http://lkml.kernel.org/r/20191009151155.27763-1-ben.dooks@codethink.co.ukSigned-off-by:
Qian Cai <cai@lca.pw> Signed-off-by:
-
Chenwandun authored
CPU0: CPU1: backing_dev_show backing_dev_store ...... ...... file = zram->backing_dev; down_read(&zram->init_lock); down_read(&zram->init_init_lock) file_path(file, ...); zram->backing_dev = backing_dev; up_read(&zram->init_lock); up_read(&zram->init_lock); gets the value of zram->backing_dev too early in backing_dev_show, which resultin the value being NULL at the beginning, and not NULL later. backtrace: d_path+0xcc/0x174 file_path+0x10/0x18 backing_dev_show+0x40/0xb4 dev_attr_show+0x20/0x54 sysfs_kf_seq_show+0x9c/0x10c kernfs_seq_show+0x28/0x30 seq_read+0x184/0x488 kernfs_fop_read+0x5c/0x1a4 __vfs_read+0x44/0x128 vfs_read+0xa0/0x138 SyS_read+0x54/0xb4 Link: http://lkml.kernel.org/r/1571046839-16814-1-git-send-email-chenwandun@huawei.comSigned-off-by:Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <stable@vger.kernel.org> [4.14+] Signed-off-by:
-
Konstantin Khlebnikov authored
Mapped, dirty and writeback pages are also counted in per-lruvec stats. These counters needs update when page is moved between cgroups. Currently is nobody *consuming* the lruvec versions of these counters and that there is no user-visible effect. Link: http://lkml.kernel.org/r/157112699975.7360.1062614888388489788.stgit@buzz Fixes: 00f3ca2c ("mm: memcontrol: per-lruvec stats infrastructure") Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com Signed-off-by:
-
Yi Li authored
mount.ocfs2 failed when reading ocfs2 filesystem superblock encounters an error. ocfs2_initialize_super() returns before allocating ocfs2_wq. ocfs2_dismount_volume() triggers the following panic. Oct 15 16:09:27 cnwarekv-205120 kernel: On-disk corruption discovered.Please run fsck.ocfs2 once the filesystem is unmounted. Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_read_locked_inode:537 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:458 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:491 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_initialize_super:2313 ERROR: status = -30 Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_fill_super:1033 ERROR: status = -30 ------------[ cut here ]------------ Oops: 0002 [#1] SMP NOPTI CPU: 1 PID: 11753 Comm: mount.ocfs2 Tainted: G E 4.14.148-200.ckv.x86_64 #1 Hardware name: Sugon H320-G30/35N16-US, BIOS 0SSDX017 12/21/2018 task: ffff967af0520000 task.stack: ffffa5f05484000 RIP: 0010:mutex_lock+0x19/0x20 Call Trace: flush_workqueue+0x81/0x460 ocfs2_shutdown_local_alloc+0x47/0x440 [ocfs2] ocfs2_dismount_volume+0x84/0x400 [ocfs2] ocfs2_fill_super+0xa4/0x1270 [ocfs2] ? ocfs2_initialize_super.isa.211+0xf20/0xf20 [ocfs2] mount_bdev+0x17f/0x1c0 mount_fs+0x3a/0x160 Link: http://lkml.kernel.org/r/1571139611-24107-1-git-send-email-yili@winhong.comSigned-off-by:Yi Li <yilikernel@gmail.com> Reviewed-by:
Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
David Hildenbrand authored
Uninitialized memmaps contain garbage and in the worst case trigger kernel BUGs, especially with CONFIG_PAGE_POISONING. They should not get touched. Let's make sure that we only consider online memory (managed by the buddy) that has initialized memmaps. ZONE_DEVICE is not applicable. page_zone() will call page_to_nid(), which will trigger VM_BUG_ON_PGFLAGS(PagePoisoned(page), page) with CONFIG_PAGE_POISONING and CONFIG_DEBUG_VM_PGFLAGS when called on uninitialized memmaps. This can be the case when an offline memory block (e.g., never onlined) is spanned by a zone. Note: As explained by Michal in [1], alloc_contig_range() will verify the range. So it boils down to the wrong access in this function. [1] http://lkml.kernel.org/r/20180423000943.GO17484@dhcp22.suse.cz Link: http://lkml.kernel.org/r/20191015120717.4858-1-david@redhat.com Fixes: f1dd2cd1 ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e8] Signed-off-by:
David Hildenbrand <david@redhat.com> Reported-by:
Michal Hocko <mhocko@kernel.org> Acked-by:
Mike Kravetz <mike.kravetz@oracle.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: <stable@vger.kernel.org> [4.13+] Signed-off-by:
-
Mike Rapoport authored
Until commit 92d12f95 ("memblock: refactor internal allocation functions") the maximal address for memblock allocations was forced to memblock.current_limit only for the allocation functions returning virtual address. The changes introduced by that commit moved the limit enforcement into the allocation core and as a result the allocation functions returning physical address also started to limit allocations to memblock.current_limit. This caused breakage of etnaviv GPU driver: etnaviv etnaviv: bound 130000.gpu (ops gpu_ops) etnaviv etnaviv: bound 134000.gpu (ops gpu_ops) etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops) etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 etnaviv-gpu 130000.gpu: command buffer outside valid memory window etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 etnaviv-gpu 134000.gpu: command buffer outside valid memory window etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 Restore the behaviour of memblock_phys* family so that these functions will not enforce memblock.current_limit. Link: http://lkml.kernel.org/r/1570915861-17633-1-git-send-email-rppt@kernel.org Fixes: 92d12f95 ("memblock: refactor internal allocation functions") Signed-off-by:
Mike Rapoport <rppt@linux.ibm.com> Reported-by:
Adam Ford <aford173@gmail.com> Tested-by: Adam Ford <aford173@gmail.com> [imx6q-logicpd] Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Honglei Wang authored
Commit 1a61ab80 ("mm: memcontrol: replace zone summing with lruvec_page_state()") has made lruvec_page_state to use per-cpu counters instead of calculating it directly from lru_zone_size with an idea that this would be more effective. Tim has reported that this is not really the case for their database benchmark which is showing an opposite results where lruvec_page_state is taking up a huge chunk of CPU cycles (about 25% of the system time which is roughly 7% of total cpu cycles) on 5.3 kernels. The workload is running on a larger machine (96cpus), it has many cgroups (500) and it is heavily direct reclaim bound. Tim Chen said: : The problem can also be reproduced by running simple multi-threaded : pmbench benchmark with a fast Optane SSD swap (see profile below). : : : 6.15% 3.08% pmbench [kernel.vmlinux] [k] lruvec_lru_size : | : |--3.07%--lruvec_lru_size : | | : | |--2.11%--cpumask_next : | | | : | | --1.66%--find_next_bit : | | : | --0.57%--call_function_interrupt : | | : | --0.55%--smp_call_function_interrupt : | : |--1.59%--0x441f0fc3d009 : | _ops_rdtsc_init_base_freq : | access_histogram : | page_fault : | __do_page_fault : | handle_mm_fault : | __handle_mm_fault : | | : | --1.54%--do_swap_page : | swapin_readahead : | swap_cluster_readahead : | | : | --1.53%--read_swap_cache_async : | __read_swap_cache_async : | alloc_pages_vma : | __alloc_pages_nodemask : | __alloc_pages_slowpath : | try_to_free_pages : | do_try_to_free_pages : | shrink_node : | shrink_node_memcg : | | : | |--0.77%--lruvec_lru_size : | | : | --0.76%--inactive_list_is_low : | | : | --0.76%--lruvec_lru_size : | : --1.50%--measure_read : page_fault : __do_page_fault : handle_mm_fault : __handle_mm_fault : do_swap_page : swapin_readahead : swap_cluster_readahead : | : --1.48%--read_swap_cache_async : __read_swap_cache_async : alloc_pages_vma : __alloc_pages_nodemask : __alloc_pages_slowpath : try_to_free_pages : do_try_to_free_pages : shrink_node : shrink_node_memcg : | : |--0.75%--inactive_list_is_low : | | : | --0.75%--lruvec_lru_size : | : --0.73%--lruvec_lru_size The likely culprit is the cache traffic the lruvec_page_state_local generates. Dave Hansen says: : I was thinking purely of the cache footprint. If it's reading : pn->lruvec_stat_local->count[idx] is three separate cachelines, so 192 : bytes of cache *96 CPUs = 18k of data, mostly read-only. 1 cgroup would : be 18k of data for the whole system and the caching would be pretty : efficient and all 18k would probably survive a tight page fault loop in : the L1. 500 cgroups would be ~90k of data per CPU thread which doesn't : fit in the L1 and probably wouldn't survive a tight page fault loop if : both logical threads were banging on different cgroups. : : It's just a theory, but it's why I noted the number of cgroups when I : initially saw this show up in profiles Fix the regression by partially reverting the said commit and calculate the lru size explicitly. Link: http://lkml.kernel.org/r/20190905071034.16822-1-honglei.wang@oracle.com Fixes: 1a61ab80 ("mm: memcontrol: replace zone summing with lruvec_page_state()") Signed-off-by:
Honglei Wang <honglei.wang@oracle.com> Reported-by:
Tim Chen <tim.c.chen@linux.intel.com> Acked-by:
-
John Hubbard authored
In several routines, the "flags" argument is incorrectly named "write". Change it to "flags". Also, in one place, the misnaming led to an actual bug: "flags & FOLL_WRITE" is required, rather than just "flags". (That problem was flagged by krobot, in v1 of this patch.) Also, change the flags argument from int, to unsigned int. You can see that this was a simple oversight, because the calling code passes "flags" to the fifth argument: gup_pgd_range(): ... if (!gup_huge_pd(__hugepd(pgd_val(pgd)), addr, PGDIR_SHIFT, next, flags, pages, nr)) ...which, until this patch, the callees referred to as "write". Also, change two lines to avoid checkpatch line length complaints, and another line to fix another oversight that checkpatch called out: missing "int" on pdshift. Link: http://lkml.kernel.org/r/20191014184639.1512873-3-jhubbard@nvidia.com Fixes: b798bec4 ("mm/gup: change write parameter to flags in fast walk") Signed-off-by:John Hubbard <jhubbard@nvidia.com> Reported-by:
Kirill A. Shutemov <kirill@shutemov.name> Suggested-by:
Ira Weiny <ira.weiny@intel.com> Acked-by:
-
John Hubbard authored
Even though gup_benchmark.c has code to handle the -w command-line option, the "w" is not part of the getopt string. It looks as if it has been missing the whole time. On my machine, this leads naturally to the following predictable result: $ sudo ./gup_benchmark -w ./gup_benchmark: invalid option -- 'w' ...which is fixed with this commit. Link: http://lkml.kernel.org/r/20191014184639.1512873-2-jhubbard@nvidia.comSigned-off-by:
-
