Pull block fixes from Jens Axboe:
 "A small collection of fixes/changes for the current series.  This
  contains:

   - Removal of dead code from Gu Zheng.

   - Revert of two bad fixes that went in earlier in this round, marking
     things as __init that were not purely used from init.

   - A fix for blk_mq_start_hw_queue() using the __blk_mq_run_hw_queue(),
     which could place us wrongly.  Make it use the non __ variant,
     which handles cases where we are called from the wrong CPU set.
     From me.

   - A fix for drbd, which allocates discard requests without room for
     the SCSI payload.  From Lars Ellenberg.

   - A fix for user-after-free in the blkcg code from Tejun.

   - Addition of limiting gaps in SG lists, if the hardware needs it.
     This is the last pre-req patch for blk-mq to enable the full NVMe
     conversion.  Could wait until 3.17, but it's simple enough so would
     be nice to have everything we need for the NVMe port in the 3.17
     release.  From me"

* 'for-linus' of git://git.kernel.dk/linux-block:
  drbd: fix NULL pointer deref in blk_add_request_payload
  blk-mq: blk_mq_start_hw_queue() should use blk_mq_run_hw_queue()
  block: add support for limiting gaps in SG lists
  bio: remove unused macro bip_vec_idx()
  Revert "block: add __init to elv_register"
  Revert "block: add __init to blkcg_policy_register"
  blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt an atomic_t
  floppy: format block0 read error message properly

blkdev_read_iter() wants to cap the iov_iter by the amount of data
remaining to the end of device.  That's what iov_iter_truncate() is for
(trim iter->count if it's above the given limit).  So far, so good, but
the argument of iov_iter_truncate() is size_t, so on 32bit boxen (in
case of a large device) we end up with that upper limit truncated down
to 32 bits *before* comparing it with iter->count.

Easily fixed by making iov_iter_truncate() take 64bit argument - it does
the right thing after such change (we only reach the assignment in there
when the current value of iter->count is greater than the limit, i.e.
for anything that would get truncated we don't reach the assignment at
all) and that argument is not the new value of iter->count - it's an
upper limit for such.

The overhead of passing u64 is not an issue - the thing is inlined, so
callers passing size_t won't pay any penalty.
Reported-and-tested-by: Theodore Tso <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull CIFS fixes from Steve French:
 "Small set of misc cifs/smb3 fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] fix mount failure with broken pathnames when smb3 mount with mapchars option
  cifs: revalidate mapping prior to satisfying read_iter request with cache=loose
  fs/cifs: fix regression in cifs_create_mf_symlink()

Pull hwmon fixes from Guenter Roeck:
 "Various minor fixes"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (gpio-fan) Change name used in hwmon_device_register_with_groups
  hwmon: (emc1403) Fix missing 'select REGMAP_I2C' in Kconfig
  hwmon: (ntc_thermistor) Use the manufacturer name properly
  devicetree: bindings: Document murata vendor prefix
  hwmon: (w83l786ng) Report correct minimum fan speed

Pull networking fixes from David Miller:

 1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.

 2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.

 3) Really really really fix locking issues in slip and slcan tty write
    wakeups, from Tyler Hall.

 4) Fix checksum offloading in fec driver, from Fugang Duan.

 5) Off by one in BPF instruction limit test, from Kees Cook.

 6) Need to clear all TSO capability flags when doing software TSO in
    tg3 driver, from Prashant Sreedharan.

 7) Fix memory leak in vlan_reorder_header() error path, from Li
    RongQing.

 8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
    from David Vrabel and Wei Liu.

 9) Fix deadlock in cxgb4 driver, from Li RongQing.

10) Prevent double free of no-cache DST entries, from Eric Dumazet.

11) Bad csum_start handling in skb_segment() leads to crashes when
    forwarding, from Tom Herbert.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: fix setting csum_start in skb_segment()
  ipv4: fix dst race in sk_dst_get()
  net: filter: Use kcalloc/kmalloc_array to allocate arrays
  trivial: net: filter: Change kerneldoc parameter order
  trivial: net: filter: Fix typo in comment
  net: allwinner: emac: Add missing free_irq
  cxgb4: use dev_port to identify ports
  xen-netback: bookkeep number of active queues in our own module
  tg3: Change nvram command timeout value to 50ms
  cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
  be2net: fix qnq mode detection on VFs
  of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
  at86rf230: fix irq setup
  net: phy: at803x: fix coccinelle warnings
  net/mlx4_core: Fix the error flow when probing with invalid VF configuration
  tulip: Poll link status more frequently for Comet chips
  net: huawei_cdc_ncm: increase command buffer size
  drivers: net: cpsw: fix dual EMAC stall when connected to same switch
  xen-netfront: recreate queues correctly when reconnecting
  xen-netfront: fix oops when disconnected from backend
  ...

Dave Jones reported that a crash is occurring in

csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive

It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1 ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull NFS client fixes from Trond Myklebust:
 "Highlights include:

   - Stable fix for a data corruption case due to incorrect cache
     validation
   - Fix a couple of false positive cache invalidations
   - Fix NFSv4 security negotiation issues"

* tag 'nfs-for-3.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: test SECINFO RPC_AUTH_GSS pseudoflavors for support
  NFS Return -EPERM if no supported or matching SECINFO flavor
  NFS check the return of nfs4_negotiate_security in nfs4_submount
  NFS: Don't mark the data cache as invalid if it has been flushed
  NFS: Clear NFS_INO_REVAL_PAGECACHE when we update the file size
  nfs: Fix cache_validity check in nfs_write_pageuptodate()

When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.

In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.

DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.

Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kcalloc/kmalloc_array to make it clear we're allocating arrays. No
integer overflow can actually happen here, since len/flen is guaranteed
to be less than BPF_MAXINSNS (4096). However, this changed makes sure
we're not going to get one if BPF_MAXINSNS were ever increased.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the order of the parameters to sk_unattached_filter_create() in
the kerneldoc to reflect the order they appear in the actual function.

This fix is only cosmetic, in the generated doc they still appear in the
correct order without the fix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3f85944f ("net: Add sysfs file
for port number") introduce dev_port to network devices. cxgb4 adapters
have multiple ports on the same PCI function, and used dev_id to
identify those ports. That use was removed by commit
8c367fcb ("cxgb4: Do not set
net_device::dev_id to VI index"), since dev_id should be used only when
devices share the same MAC address.

Using dev_port for cxgb4 allows different ports on the same PCI function
to be identified.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original code uses netdev->real_num_tx_queues to bookkeep number of
queues and invokes netif_set_real_num_tx_queues to set the number of
queues. However, netif_set_real_num_tx_queues doesn't allow
real_num_tx_queues to be smaller than 1, which means setting the number
to 0 will not work and real_num_tx_queues is untouched.

This is bogus when xenvif_free is invoked before any number of queues is
allocated. That function needs to iterate through all queues to free
resources. Using the wrong number of queues results in NULL pointer
dereference.

So we bookkeep the number of queues in xen-netback to solve this
problem. This fixes a regression introduced by multiqueue patchset in
3.16-rc1.

There's another bug in original code that the real number of RX queues
is never set. In current Xen multiqueue design, the number of TX queues
and RX queues are in fact the same. We need to set the numbers of TX and
RX queues to the same value.

Also remove xenvif_select_queue and leave queue selection to core
driver, as suggested by David Miller.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
CC: Ian Campbell <ian.campbell@citrix.com>
CC: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 506724c4 "tg3: Override clock,
link aware and link idle mode during NVRAM dump" changed the timeout
value for nvram command execution from 100ms to 1ms. But the 1ms
timeout value was only sufficient for nvram read operations but not
write operations for most of the devices supported by tg3 driver.
This patch sets the MAX to 50ms. Also it uses usleep_range instead
of udelay.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 648cd48c
The hwmon name attributes must not include '-' so the name must be
rename from gpio-fan to gpio_fan
Signed-off-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull ARM SoC fixes from Arnd Bergmann:
 "A new set of bug fixes for 3.16, containing patches for seven
  platforms:

  at91:
    - drivers/misc fix for Kconfig PWM symbol
    - correction of several values in DT after conversion to CCF
    - fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

  imx:
    - Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
      because controller base CD/WP is not working in esdhc driver due to
      runtime PM support
    - A couple of random ventana gw5xxx board fixes
    - Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
      IPUv3 driver out of staging tree
    - Fix enet/fec clock selection on imx6sl
    - Fix display node on imx53-m53evk board
    - A couple of Cubox-i updates from Russell, which were omitted from
      the merge window due to dependency

  integrator:
    - fix an OF-related regression against 3.15

  mvebu:
    - mvebu (v7)
       - Fix broken SoC ID detection
       - Select ARM_CPU_SUSPEND for v7
       - Remove armada38x compatible string (no users yet)
       - Enable Dove SoC in mvebu_v7_defconfig
    - kirkwood
       - Fix phy-connection-type on GuruPlug board

  qcom:
    - enable gsbi driver in defconfig
    - fix section mismatch warning in serial driver

  samsung:
    - use WFI macro in platform_do_lowpower because exynos cpuhotplug
      includes a hardcoded WFI instruction and it causes compile error
      in Thumb-2 mode.
    - fix GIC reg sizes for exynos4 SoCs
    - remove reset timer counter value during boot and resume for mct
      to fix a big jump in printk timestamps
    - fix pm code to check cortex-A9 for another exynos SoCs
    - don't rely on firmware's secondary_cpu_start for mcpm

  sti:
    - Ethernet clocks were wrongly defined for STiH415/416 platforms
    - STiH416 B2020 revision E DTS file name contained uppercase, change to
      lowercase"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols
  ARM: integrator: fix OF-related regression
  ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
  ARM: dts: kirkwood: fix phy-connection-type for Guruplug
  ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
  ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
  ARM: dts: imx51-babbage: Fix esdhc setup
  ARM: dts: mx5: Move the display out of soc {} node
  ARM: dts: mx5: Fix IPU port node placement
  ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
  ARM: mvebu: Fix broken SoC ID detection
  ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
  ARM: multi_v7_defconfig: Add QCOM GSBI driver
  ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
  tty: serial: msm: Fix section mismatch warning
  ...

Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:

- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols

Merge "mvebu fixes for v3.16" from Jason Cooper:

 - mvebu
    - Fix broken SoC ID detection
    - Select ARM_CPU_SUSPEND for v7
    - Remove armada38x compatible string (no users yet)

 - kirkwood
    - Fix phy-connection-type on GuruPlug board

* tag 'mvebu-fixes-3.16' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
  ARM: dts: kirkwood: fix phy-connection-type for Guruplug
  ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
  ARM: mvebu: Fix broken SoC ID detection

Pull Ceph fix from Sage Weil:
 "This fixes a corner case for cloned RBD images"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: handle parent_overlap on writes correctly

The at91sam9261 doesn't actually have a slow RC oscillator, remove it from the
dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Discards don't have any payload.
But the scsi layer still expects a bio_vec it can use internally,
see sd_setup_discard_cmnd() and blk_add_request_payload().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Define at91sam9261ek's slow crystal frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

mainck (CKGR_MCFR register) is actually using main_osc (CKGR_MOR register).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

In commit 4cab259f, the emc1403 driver was converted to use regmap but the
necessary Kconfig option was not added.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Currently it calls __blk_mq_run_hw_queue(), which depends on the
CPU placement being correct. This means it's not possible to call
blk_mq_start_hw_queues(q) from a context that is correct for all
queues, leading to triggering the

WARN_ON(!cpumask_test_cpu(raw_smp_processor_id(), hctx->cpumask));

in __blk_mq_run_hw_queue().
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.

This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt

Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add Murata Manufacturing Co., Ltd. to the list of device tree
vendor prefixes.

Murata manufactures NTC (Negative Temperature Coefficient) based
Thermistors for small scale applications like Mobiles and PDAs.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Current code is buggy, it shows the current fan speed as minimum fan speed.
Fix up show_fan_reg macro to correctly report fan and fan_min speed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull powerpc fixes and cleanups from Ben Herrenschmidt:
 "Here are a handful or two of powerpc fixes and simple/trivial
  cleanups.  A bunch of them fix ftrace with the new ABI v2 in Little
  Endian, the rest is a scattering of fairly simple things"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Don't skip ePAPR spin-table CPUs
  powerpc/module: Fix TOC symbol CRC
  powerpc/powernv: Remove OPAL v1 takeover
  powerpc/kmemleak: Do not scan the DART table
  selftests/powerpc: Use the test harness for the TM DSCR test
  powerpc/cell: cbe_thermal.c: Cleaning up a variable is of the wrong type
  powerpc/kprobes: Fix jprobes on ABI v2 (LE)
  powerpc/ftrace: Use pr_fmt() to namespace error messages
  powerpc/ftrace: Fix nop of modules on 64bit LE (ABIv2)
  powerpc/ftrace: Fix inverted check of create_branch()
  powerpc/ftrace: Fix typo in mask of opcode
  powerpc: Add ppc_global_function_entry()
  powerpc/macintosh/smu.c: Fix closing brace followed by if
  powerpc: Remove __arch_swab*
  powerpc: Remove ancient DEBUG_SIG code
  powerpc/kerenl: Enable EEH for IO accessors

Pull vhost cleanups from Michael S Tsirkin:
 "Two cleanup patches removing code duplication that got introduced by
  changes in rc1.  Not fixing crashes, but I'd rather not carry the
  duplicate code until the next merge window"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost-scsi: don't open-code kvfree
  vhost-net: don't open-code kvfree

Merge tag 'trace-fixes-v3.16-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing cleanups and fixes from Steven Rostedt:
 "This includes three patches from Oleg Nesterov.  The first is a fix to
  a race condition that happens between enabling/disabling syscall
  tracepoints and new process creations (the check to go into the ptrace
  path for a process can be set when it shouldn't, or not set when it
  should).  Not a major bug but one that should be fixed and even
  applied to stable.

  The other two patches are cleanup/fixes that are not that critical,
  but for an -rc1 release would be nice to have.  They both deal with
  syscall tracepoints.

  It also includes a patch to introduce a new macro for the
  TRACE_EVENT() format called __field_struct().  Originally, __field()
  was used to record any variable into a trace event, but with the
  addition of setting the "is signed" attribute, the check causes
  anything but a primitive variable to fail to compile.  That is,
  structs and unions can't be used as they once were.  When the "is
  signed" check was introduce there were only primitive variables being
  recorded.  But that will change soon and it was reported that
  __field() causes build failures.

  To solve the __field() issue, __field_struct() is introduced to allow
  trace_events to be able to record complex types too"

* tag 'trace-fixes-v3.16-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Add __field_struct macro for TRACE_EVENT()
  tracing: syscall_regfunc() should not skip kernel threads
  tracing: Change syscall_*regfunc() to check PF_KTHREAD and use for_each_process_thread()
  tracing: Fix syscall_*regfunc() vs copy_process() race

AT91 symbols AT91SAM9263, AT91SAM9RL, and AT91SAM9G45 do not exist and this
patch changes them to their correct ARCH_* version.
These symbols are chosen instead of the SOC_* ones because this driver is not
converted to DT.
Anyway, the ATMEL_PWM symbol and the associated driver will be removed soon,
during the move to the PWM sub-system.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Commit 59a53afe "powerpc: Don't setup
CPUs with bad status" broke ePAPR SMP booting.  ePAPR says that CPUs
that aren't presently running shall have status of disabled, with
enable-method being used to determine whether the CPU can be enabled.

Fix by checking for spin-table, which is currently the only supported
enable-method.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The commit 71ec7c55 introduced the magic symbol ".TOC." for ELFv2 ABI.
This symbol is built manually and has no CRC value computed. A zero value
is put in the CRC section to avoid modpost complaining about a missing CRC.
Unfortunately, this breaks the kernel module loading when the kernel is
relocated (kdump case for instance) because of the relocation applied to
the kcrctab values.

This patch compute a CRC value for the TOC symbol which will match the one
compute by the kernel when it is relocated - aka '0 - relocate_start' done in
maybe_relocated called by check_version (module.c).
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 27f44888 "Add OPAL takeover from PowerVM" we added support
for "takeover" on OPAL v1 machines.

This was a mode of operation where we would boot under pHyp, and query
for the presence of OPAL. If detected we would then do a special
sequence to take over the machine, and the kernel would end up running
in hypervisor mode.

OPAL v1 was never a supported product, and was never shipped outside
IBM. As far as we know no one is still using it.

Newer versions of OPAL do not use the takeover mechanism. Although the
query for OPAL should be harmless on machines with newer OPAL, we have
seen a machine where it causes a crash in Open Firmware.

The code in early_init_devtree() to copy boot_command_line into cmd_line
was added in commit 817c21ad "Get kernel command line accross OPAL
takeover", and AFAIK is only used by takeover, so should also be
removed.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

cxgb4_netdev maybe lead to dead lock, since it uses a spin lock, and be called
in both thread and softirq context, but not disable BH, the lockdep report is
below; In fact, cxgb4_netdev only reads adap_rcu_list with RCU protection, so
not need to hold spin lock again.
	=================================
	[ INFO: inconsistent lock state ]
	3.14.7+ #24 Tainted: G         C O
	---------------------------------
	inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
	radvd/3794 [HC0[0]:SC1[1]:HE1:SE0] takes:
	 (adap_rcu_lock){+.?...}, at: [<ffffffffa09989ea>] clip_add+0x2c/0x116 [cxgb4]
	{SOFTIRQ-ON-W} state was registered at:
	  [<ffffffff810fca81>] __lock_acquire+0x34a/0xe48
	  [<ffffffff810fd98b>] lock_acquire+0x82/0x9d
	  [<ffffffff815d6ff8>] _raw_spin_lock+0x34/0x43
	  [<ffffffffa09989ea>] clip_add+0x2c/0x116 [cxgb4]
	  [<ffffffffa0998beb>] cxgb4_inet6addr_handler+0x117/0x12c [cxgb4]
	  [<ffffffff815da98b>] notifier_call_chain+0x32/0x5c
	  [<ffffffff815da9f9>] __atomic_notifier_call_chain+0x44/0x6e
	  [<ffffffff815daa32>] atomic_notifier_call_chain+0xf/0x11
	  [<ffffffff815b1356>] inet6addr_notifier_call_chain+0x16/0x18
	  [<ffffffffa01f72e5>] ipv6_add_addr+0x404/0x46e [ipv6]
	  [<ffffffffa01f8df0>] addrconf_add_linklocal+0x5f/0x95 [ipv6]
	  [<ffffffffa01fc3e9>] addrconf_notify+0x632/0x841 [ipv6]
	  [<ffffffff815da98b>] notifier_call_chain+0x32/0x5c
	  [<ffffffff810e09a1>] __raw_notifier_call_chain+0x9/0xb
	  [<ffffffff810e09b2>] raw_notifier_call_chain+0xf/0x11
	  [<ffffffff8151b3b7>] call_netdevice_notifiers_info+0x4e/0x56
	  [<ffffffff8151b3d0>] call_netdevice_notifiers+0x11/0x13
	  [<ffffffff8151c0a6>] netdev_state_change+0x1f/0x38
	  [<ffffffff8152f004>] linkwatch_do_dev+0x3b/0x49
	  [<ffffffff8152f184>] __linkwatch_run_queue+0x10b/0x144
	  [<ffffffff8152f1dd>] linkwatch_event+0x20/0x27
	  [<ffffffff810d7bc0>] process_one_work+0x1cb/0x2ee
	  [<ffffffff810d7e3b>] worker_thread+0x12e/0x1fc
	  [<ffffffff810dd391>] kthread+0xc4/0xcc
	  [<ffffffff815dc48c>] ret_from_fork+0x7c/0xb0
	irq event stamp: 3388
	hardirqs last  enabled at (3388): [<ffffffff810c6c85>]
	__local_bh_enable_ip+0xaa/0xd9
	hardirqs last disabled at (3387): [<ffffffff810c6c2d>]
	__local_bh_enable_ip+0x52/0xd9
	softirqs last  enabled at (3288): [<ffffffffa01f1d5b>]
	rcu_read_unlock_bh+0x0/0x2f [ipv6]
	softirqs last disabled at (3289): [<ffffffff815ddafc>]
	do_softirq_own_stack+0x1c/0x30

	other info that might help us debug this:
	 Possible unsafe locking scenario:

	       CPU0
	       ----
	  lock(adap_rcu_lock);
	  <Interrupt>
	    lock(adap_rcu_lock);

	 *** DEADLOCK ***

	5 locks held by radvd/3794:
	 #0:  (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffffa020b85a>]
	rawv6_sendmsg+0x74b/0xa4d [ipv6]
	 #1:  (rcu_read_lock){.+.+..}, at: [<ffffffff8151ac6b>]
	rcu_lock_acquire+0x0/0x29
	 #2:  (rcu_read_lock){.+.+..}, at: [<ffffffffa01f4cca>]
	rcu_lock_acquire.constprop.16+0x0/0x30 [ipv6]
	 #3:  (rcu_read_lock){.+.+..}, at: [<ffffffff810e09b4>]
	rcu_lock_acquire+0x0/0x29
	 #4:  (rcu_read_lock){.+.+..}, at: [<ffffffffa0998782>]
	rcu_lock_acquire.constprop.40+0x0/0x30 [cxgb4]

	stack backtrace:
	CPU: 7 PID: 3794 Comm: radvd Tainted: G         C O 3.14.7+ #24
	Hardware name: Supermicro X7DBU/X7DBU, BIOS 6.00 12/03/2007
	 ffffffff81f15990 ffff88012fdc36a8 ffffffff815d0016 0000000000000006
	 ffff8800c80dc2a0 ffff88012fdc3708 ffffffff815cc727 0000000000000001
	 0000000000000001 ffff880100000000 ffffffff81015b02 ffff8800c80dcb58
	Call Trace:
	 <IRQ>  [<ffffffff815d0016>] dump_stack+0x4e/0x71
	 [<ffffffff815cc727>] print_usage_bug+0x1ec/0x1fd
	 [<ffffffff81015b02>] ? save_stack_trace+0x27/0x44
	 [<ffffffff810fbfaa>] ? check_usage_backwards+0xa0/0xa0
	 [<ffffffff810fc640>] mark_lock+0x11b/0x212
	 [<ffffffff810fca0b>] __lock_acquire+0x2d4/0xe48
	 [<ffffffff810fbfaa>] ? check_usage_backwards+0xa0/0xa0
	 [<ffffffff810fbff6>] ? check_usage_forwards+0x4c/0xa6
	 [<ffffffff810c6c8a>] ? __local_bh_enable_ip+0xaf/0xd9
	 [<ffffffff810fd98b>] lock_acquire+0x82/0x9d
	 [<ffffffffa09989ea>] ? clip_add+0x2c/0x116 [cxgb4]
	 [<ffffffffa0998782>] ? rcu_read_unlock+0x23/0x23 [cxgb4]
	 [<ffffffff815d6ff8>] _raw_spin_lock+0x34/0x43
	 [<ffffffffa09989ea>] ? clip_add+0x2c/0x116 [cxgb4]
	 [<ffffffffa09987b0>] ? rcu_lock_acquire.constprop.40+0x2e/0x30 [cxgb4]
	 [<ffffffffa0998782>] ? rcu_read_unlock+0x23/0x23 [cxgb4]
	 [<ffffffffa09989ea>] clip_add+0x2c/0x116 [cxgb4]
	 [<ffffffffa0998beb>] cxgb4_inet6addr_handler+0x117/0x12c [cxgb4]
	 [<ffffffff810fd99d>] ? lock_acquire+0x94/0x9d
	 [<ffffffff810e09b4>] ? raw_notifier_call_chain+0x11/0x11
	 [<ffffffff815da98b>] notifier_call_chain+0x32/0x5c
	 [<ffffffff815da9f9>] __atomic_notifier_call_chain+0x44/0x6e
	 [<ffffffff815daa32>] atomic_notifier_call_chain+0xf/0x11
	 [<ffffffff815b1356>] inet6addr_notifier_call_chain+0x16/0x18
	 [<ffffffffa01f72e5>] ipv6_add_addr+0x404/0x46e [ipv6]
	 [<ffffffff810fde6a>] ? trace_hardirqs_on+0xd/0xf
	 [<ffffffffa01fb634>] addrconf_prefix_rcv+0x385/0x6ea [ipv6]
	 [<ffffffffa0207950>] ndisc_rcv+0x9d3/0xd76 [ipv6]
	 [<ffffffffa020d536>] icmpv6_rcv+0x592/0x67b [ipv6]
	 [<ffffffff810c6c85>] ? __local_bh_enable_ip+0xaa/0xd9
	 [<ffffffff810c6c85>] ? __local_bh_enable_ip+0xaa/0xd9
	 [<ffffffff810fd8dc>] ? lock_release+0x14e/0x17b
	 [<ffffffffa020df97>] ? rcu_read_unlock+0x21/0x23 [ipv6]
	 [<ffffffff8150df52>] ? rcu_read_unlock+0x23/0x23
	 [<ffffffffa01f4ede>] ip6_input_finish+0x1e4/0x2fc [ipv6]
	 [<ffffffffa01f540b>] ip6_input+0x33/0x38 [ipv6]
	 [<ffffffffa01f5557>] ip6_mc_input+0x147/0x160 [ipv6]
	 [<ffffffffa01f4ba3>] ip6_rcv_finish+0x7c/0x81 [ipv6]
	 [<ffffffffa01f5397>] ipv6_rcv+0x3a1/0x3e2 [ipv6]
	 [<ffffffff8151ef96>] __netif_receive_skb_core+0x4ab/0x511
	 [<ffffffff810fdc94>] ? mark_held_locks+0x71/0x99
	 [<ffffffff8151f0c0>] ? process_backlog+0x69/0x15e
	 [<ffffffff8151f045>] __netif_receive_skb+0x49/0x5b
	 [<ffffffff8151f0cf>] process_backlog+0x78/0x15e
	 [<ffffffff8151f571>] ? net_rx_action+0x1a2/0x1cc
	 [<ffffffff8151f47b>] net_rx_action+0xac/0x1cc
	 [<ffffffff810c69b7>] ? __do_softirq+0xad/0x218
	 [<ffffffff810c69ff>] __do_softirq+0xf5/0x218
	 [<ffffffff815ddafc>] do_softirq_own_stack+0x1c/0x30
	 <EOI>  [<ffffffff810c6bb6>] do_softirq+0x38/0x5d
	 [<ffffffffa01f1d5b>] ? ip6_copy_metadata+0x156/0x156 [ipv6]
	 [<ffffffff810c6c78>] __local_bh_enable_ip+0x9d/0xd9
	 [<ffffffffa01f1d88>] rcu_read_unlock_bh+0x2d/0x2f [ipv6]
	 [<ffffffffa01f28b4>] ip6_finish_output2+0x381/0x3d8 [ipv6]
	 [<ffffffffa01f49ef>] ip6_finish_output+0x6e/0x73 [ipv6]
	 [<ffffffffa01f4a70>] ip6_output+0x7c/0xa8 [ipv6]
	 [<ffffffff815b1bfa>] dst_output+0x18/0x1c
	 [<ffffffff815b1c9e>] ip6_local_out+0x1c/0x21
	 [<ffffffffa01f2489>] ip6_push_pending_frames+0x37d/0x427 [ipv6]
	 [<ffffffff81558af8>] ? skb_orphan+0x39/0x39
	 [<ffffffffa020b85a>] ? rawv6_sendmsg+0x74b/0xa4d [ipv6]
	 [<ffffffffa020ba51>] rawv6_sendmsg+0x942/0xa4d [ipv6]
	 [<ffffffff81584cd2>] inet_sendmsg+0x3d/0x66
	 [<ffffffff81508930>] __sock_sendmsg_nosec+0x25/0x27
	 [<ffffffff8150b0d7>] sock_sendmsg+0x5a/0x7b
	 [<ffffffff810fd8dc>] ? lock_release+0x14e/0x17b
	 [<ffffffff8116d756>] ? might_fault+0x9e/0xa5
	 [<ffffffff8116d70d>] ? might_fault+0x55/0xa5
	 [<ffffffff81508cb1>] ? copy_from_user+0x2a/0x2c
	 [<ffffffff8150b70c>] ___sys_sendmsg+0x226/0x2d9
	 [<ffffffff810fcd25>] ? __lock_acquire+0x5ee/0xe48
	 [<ffffffff810fde01>] ? trace_hardirqs_on_caller+0x145/0x1a1
	 [<ffffffff8118efcb>] ? slab_free_hook.isra.71+0x50/0x59
	 [<ffffffff8115c81f>] ? release_pages+0xbc/0x181
	 [<ffffffff810fd99d>] ? lock_acquire+0x94/0x9d
	 [<ffffffff81115e97>] ? read_seqcount_begin.constprop.25+0x73/0x90
	 [<ffffffff8150c408>] __sys_sendmsg+0x3d/0x5b
	 [<ffffffff8150c433>] SyS_sendmsg+0xd/0x19
	 [<ffffffff815dc53d>] system_call_fastpath+0x1a/0x1f
Reported-by: Ben Greear <greearb@candelatech.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix nfs4_negotiate_security to create an rpc_clnt used to test each SECINFO
returned pseudoflavor. Check credential creation  (and gss_context creation)
which is important for RPC_AUTH_GSS pseudoflavors which can fail for multiple
reasons including mis-configuration.

Don't call nfs4_negotiate in nfs4_submount as it was just called by
nfs4_proc_lookup_mountpoint (nfs4_proc_lookup_common)
Signed-off-by: Andy Adamson <andros@netapp.com>
[Trond: fix corrupt return value from nfs_find_best_sec()]
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>