- 25 Jun, 2019 40 commits
-
-
Andy Strohman authored
commit f77bf486 upstream. When dumping stations, memory allocated for station_info's pertid member will leak if the nl80211 header cannot be added to the sk_buff due to insufficient tail room. I noticed this leak in the kmalloc-2048 cache. Cc: stable@vger.kernel.org Fixes: 8689c051 ("cfg80211: dynamically allocate per-tid stats for station info") Signed-off-by: Andy Strohman <andy@uplevelsystems.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Yu Wang authored
commit 79c92ca4 upstream. When receiving a deauthentication/disassociation frame from a TDLS peer, a station should not disconnect the current AP, but only disable the current TDLS link if it's enabled. Without this change, a TDLS issue can be reproduced by following the steps as below: 1. STA-1 and STA-2 are connected to AP, bidirection traffic is running between STA-1 and STA-2. 2. Set up TDLS link between STA-1 and STA-2, stay for a while, then teardown TDLS link. 3. Repeat step #2 and monitor the connection between STA and AP. During the test, one STA may send a deauthentication/disassociation frame to another, after TDLS teardown, with reason code 6/7, which means: Class 2/3 frame received from nonassociated STA. On receive this frame, the receiver STA will disconnect the current AP and then reconnect. It's not a expected behavior, purpose of this frame should be disabling the TDLS link, not the link with AP. Cc: stable@vger.kernel.org Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Manikanta Pubbisetty authored
commit 33d915d9 upstream. As per the current design, in the case of sw crypto controlled devices, it is the device which advertises the support for AP/VLAN iftype based on it's ability to tranmsit packets encrypted in software (In VLAN functionality, group traffic generated for a specific VLAN group is always encrypted in software). Commit db3bdcb9 ("mac80211: allow AP_VLAN operation on crypto controlled devices") has introduced this change. Since 4addr AP operation also uses AP/VLAN iftype, this conditional way of advertising AP/VLAN support has broken 4addr AP mode operation on crypto controlled devices which do not support VLAN functionality. In the case of ath10k driver, not all firmwares have support for VLAN functionality but all can support 4addr AP operation. Because AP/VLAN support is not advertised for these devices, 4addr AP operations are also blocked. Fix this by allowing 4addr operation on devices which do not support AP/VLAN iftype but can support 4addr AP operation (decision is based on the wiphy flag WIPHY_FLAG_4ADDR_AP). Cc: stable@vger.kernel.org Fixes: db3bdcb9 ("mac80211: allow AP_VLAN operation on crypto controlled devices") Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johannes Berg authored
commit 588f7d39 upstream. When receiving a robust management frame, drop it if we don't have rx->sta since then we don't have a security association and thus couldn't possibly validate the frame. Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Biggers authored
commit 4f488fbc upstream. In wiphy_new_nm(), if an error occurs after dev_set_name() and device_initialize() have already been called, it's necessary to call put_device() (via wiphy_free()) to avoid a memory leak. Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com Fixes: 1f87f7d3 ("cfg80211: add rfkill support") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Christian Brauner authored
commit d728cf79 upstream. When propagating mounts across mount namespaces owned by different user namespaces it is not possible anymore to move or umount the mount in the less privileged mount namespace. Here is a reproducer: sudo mount -t tmpfs tmpfs /mnt sudo --make-rshared /mnt # create unprivileged user + mount namespace and preserve propagation unshare -U -m --map-root --propagation=unchanged # now change back to the original mount namespace in another terminal: sudo mkdir /mnt/aaa sudo mount -t tmpfs tmpfs /mnt/aaa # now in the unprivileged user + mount namespace mount --move /mnt/aaa /opt Unfortunately, this is a pretty big deal for userspace since this is e.g. used to inject mounts into running unprivileged containers. So this regression really needs to go away rather quickly. The problem is that a recent change falsely locked the root of the newly added mounts by setting MNT_LOCKED. Fix this by only locking the mounts on copy_mnt_ns() and not when adding a new mount. Fixes: 3bd045cc ("separate copying and locking mount tree on cross-userns copies") Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Tested-by: Christian Brauner <christian@brauner.io> Acked-by: Christian Brauner <christian@brauner.io> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Christian Brauner <christian@brauner.io> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andy Lutomirski authored
commit ff17bbe0 upstream. GCC 5.5.0 sometimes cleverly hoists reads of the pvclock and/or hvclock pages before the vclock mode checks. This creates a path through vclock_gettime() in which no vclock is enabled at all (due to disabled TSC on old CPUs, for example) but the pvclock or hvclock page nevertheless read. This will segfault on bare metal. This fixes commit 459e3a21 ("gcc-9: properly declare the {pv,hv}clock_page storage") in the sense that, before that commit, GCC didn't seem to generate the offending code. There was nothing wrong with that commit per se, and -stable maintainers should backport this to all supported kernels regardless of whether the offending commit was present, since the same crash could just as easily be triggered by the phase of the moon. On GCC 9.1.1, this doesn't seem to affect the generated code at all, so I'm not too concerned about performance regressions from this fix. Cc: stable@vger.kernel.org Cc: x86@kernel.org Cc: Borislav Petkov <bp@alien8.de> Reported-by: Duncan Roe <duncan_roe@optusnet.com.au> Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Steve French authored
commit 8d526d62 upstream. Some servers such as Windows 10 will return STATUS_INSUFFICIENT_RESOURCES as the number of simultaneous SMB3 requests grows (even though the client has sufficient credits). Return EAGAIN on STATUS_INSUFFICIENT_RESOURCES so that we can retry writes which fail with this status code. This (for example) fixes large file copies to Windows 10 on fast networks. Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marcel Holtmann authored
commit 693cd8ce upstream. When trying to align the minimum encryption key size requirement for Bluetooth connections, it turns out doing this in a central location in the HCI connection handling code is not possible. Original Bluetooth version up to 2.0 used a security model where the L2CAP service would enforce authentication and encryption. Starting with Bluetooth 2.1 and Secure Simple Pairing that model has changed into that the connection initiator is responsible for providing an encrypted ACL link before any L2CAP communication can happen. Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and before devices are causing a regression. The encryption key size check needs to be moved out of the HCI connection handling into the L2CAP channel setup. To achieve this, the current check inside hci_conn_security() has been moved into l2cap_check_enc_key_size() helper function and then called from four decisions point inside L2CAP to cover all combinations of Secure Simple Pairing enabled devices and device using legacy pairing and legacy service security model. Fixes: d5bb334a ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections") Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marcel Holtmann authored
commit d5bb334a upstream. The minimum encryption key size for LE connections is 56 bits and to align LE with BR/EDR, enforce 56 bits of minimum encryption key size for BR/EDR connections as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Gao Xiang authored
commit 5efe5137 upstream. There are some backward incompatible features pending for months, mainly due to on-disk format expensions. However, we should ensure that it cannot be mounted with old kernels. Otherwise, it will causes unexpected behaviors. Fixes: ba2b77a8 ("staging: erofs: add super block operations") Cc: <stable@vger.kernel.org> # 4.19+ Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Gao Xiang <gaoxiang25@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Todd Kjos authored
commit a370003c upstream. There is a race between the binder driver cleaning up a completed transaction via binder_free_transaction() and a user calling binder_ioctl(BC_FREE_BUFFER) to release a buffer. It doesn't matter which is first but they need to be protected against running concurrently which can result in a UAF. Signed-off-by: Todd Kjos <tkjos@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ville Syrjälä authored
commit 475df5d0 upstream. We're now calling intel_pipe_config_compare(..., true) uncoditionally which means we're always going clobber the calculated M/N values with the old values if the fuzzy M/N check passes. That causes problems because the fuzzy check allows for a huge difference in the values. I'm actually tempted to just make the M/N checks exact, but that might prevent fastboot from kicking in when people want it. So for now let's overwrite the computed values with the old values only if decide to skip the modeset. v2: Copy has_drrs along with M/N M2/N2 values Cc: stable@vger.kernel.org Cc: Blubberbub@protonmail.com Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Tested-by: Blubberbub@protonmail.com Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110782 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110675 Fixes: d19f958d ("drm/i915: Enable fastset for non-boot modesets.") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190612172423.25231-1-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com> (cherry picked from commit f0521558) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190619120929.4057-1-ville.syrjala@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Hellstrom authored
commit cc0ba0d8 upstream. The HB port may not be available for various reasons. Either it has been disabled by a config option or by the hypervisor for other reasons. In that case, make sure we have a backup plan and use the backdoor port instead with a performance penalty. Cc: stable@vger.kernel.org Fixes: 89da76fd ("drm/vmwgfx: Add VMWare host messaging capability") Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Amir Goldstein authored
commit 6dde1e42 upstream. Relax the condition that overlayfs supports nfs export, to require that i_ino is consistent with st_ino/d_ino. It is enough to require that st_ino and d_ino are consistent. This fixes the failure of xfstest generic/504, due to mismatch of st_ino to inode number in the output of /proc/locks. Fixes: 12574a9f ("ovl: consistent i_ino for non-samefs with xino") Cc: <stable@vger.kernel.org> # v4.19 Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sean Christopherson authored
commit b6b80c78 upstream. SVM's Nested Page Tables (NPT) reuses x86 paging for the host-controlled page walk. For 32-bit KVM, this means PAE paging is used even when TDP is enabled, i.e. the PAE root array needs to be allocated. Fixes: ee6268ba ("KVM: x86: Skip pae_root shadow allocation if tdp enabled") Cc: stable@vger.kernel.org Reported-by: Jiri Palecek <jpalecek@web.de> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Anisse Astier authored
commit adeaa21a upstream. Fix ssbd.c which depends implicitly on asm/ptrace.h including linux/prctl.h (through for example linux/compat.h, then linux/time.h, linux/seqlock.h, linux/spinlock.h and linux/irqflags.h), and uses PR_SPEC* defines. This is an issue since we'll soon be removing the include from asm/ptrace.h. Fixes: 9cdc0108 ("arm64: ssbd: Add prctl interface for per-thread mitigation") Cc: stable@vger.kernel.org Signed-off-by: Anisse Astier <aastier@freebox.fr> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Anisse Astier authored
commit 35341ca0 upstream. Pulling linux/prctl.h into asm/ptrace.h in the arm64 UAPI headers causes userspace build issues for any program (e.g. strace and qemu) that includes both <sys/prctl.h> and <linux/ptrace.h> when using musl libc: | error: redefinition of 'struct prctl_mm_map' | struct prctl_mm_map { See https://github.com/foundriesio/meta-lmp/commit/6d4a106e191b5d79c41b9ac78fd321316d3013c0 for a public example of people working around this issue. Although it's a bit grotty, fix this breakage by duplicating the prctl constant definitions. Since these are part of the kernel ABI, they cannot be changed in future and so it's not the end of the world to have them open-coded. Fixes: 43d4da2c ("arm64/sve: ptrace and ELF coredump support") Cc: stable@vger.kernel.org Acked-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Anisse Astier <aastier@freebox.fr> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Faiz Abbas authored
commit 88a74841 upstream. If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Since am571x-, am572x- and am574x-idk don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Faiz Abbas authored
commit c3c0b70c upstream. Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest dra76x data manual[1]. The new iodelay values will have better marginality and should prevent issues in corner cases. Also this particular pinctrl-array is using spaces instead of tabs for spacing between the values and the comments. Fix this as well. [1] http://www.ti.com/lit/ds/symlink/dra76p.pdf Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> [tony@atomide.com: updated description with a bit more info] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jan Kundrát authored
commit cc538ca4 upstream. Compared to kernel 5.0, patches merged for 5.1 added support for A38x' PHY guarded by a config option which was not enabled by default. As a result, there was no eth1 and eth2 on a Solid Run Clearfog Base. Ensure that A38x PHY is enabled on mvebu. [gregory: issue appeared in 5.1 not in 5.2 and added Fixes tag] Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: David S. Miller <davem@davemloft.net> Cc: Maxime Chevallier <maxime.chevallier@bootlin.com> Fixes: a10c1c81 ("net: marvell: neta: add comphy support") Cc: stable@kernel.org Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Fabio Estevam authored
commit b25af2ff upstream. Since commit 1e434b70 ("ARM: imx: update the cpu power up timing setting on i.mx6sx") some characters loss is noticed on i.MX6ULL UART as reported by Christoph Niedermaier. The intention of such commit was to increase the SW2ISO field for i.MX6SX only, but since cpuidle-imx6sx is also used on i.MX6UL/i.MX6ULL this caused unintended side effects on other SoCs. Fix this problem by keeping the original SW2ISO value for i.MX6UL/i.MX6ULL and only increase SW2ISO in the i.MX6SX case. Cc: stable@vger.kernel.org Fixes: 1e434b70 ("ARM: imx: update the cpu power up timing setting on i.mx6sx") Reported-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Naveen N. Rao authored
commit 758f2046 upstream. BPF_ALU64 div/mod operations are currently using signed division, unlike BPF_ALU32 operations. Fix the same. DIV64 and MOD64 overflow tests pass with this fix. Fixes: 156d0e29 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
ShihPo Hung authored
commit bf587caa upstream. Because RISC-V compliant implementations can cache invalid entries in TLB, an SFENCE.VMA is necessary after changes to the page table. This patch adds an SFENCE.vma for the vmalloc_fault path. Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com> [paul.walmsley@sifive.com: reversed tab->whitespace conversion, wrapped comment lines] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: linux-riscv@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Willem de Bruijn authored
commit fd704bd5 upstream. CAN supports software tx timestamps as of the below commit. Purge any queued timestamp packets on socket destroy. Fixes: 51f31cab ("ip: support for TX timestamps on UDP and RAW sockets") Reported-by: syzbot+a90604060cb40f5bdd16@syzkaller.appspotmail.com Signed-off-by: Willem de Bruijn <willemb@google.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joakim Zhang authored
commit 247e5356 upstream. Current we can meet timeout issue when setting a small bitrate like 10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock = 30MHZ): | root@imx6ul7d:~# ip link set can0 up type can bitrate 10000 A link change request failed with some changes committed already. Interface can0 may have been left with an inconsistent configuration, please check. | RTNETLINK answers: Connection timed out It is caused by calling of flexcan_chip_unfreeze() timeout. Originally the code is using usleep_range(10, 20) for unfreeze operation, but the patch (8badd65e can: flexcan: avoid calling usleep_range from interrupt context) changed it into udelay(10) which is only a half delay of before, there're also some other delay changes. After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue. Meanwhile, Rasmus Villemoes reported that even with a timeout of 100, flexcan_probe() fails on the MPC8309, which requires a value of at least 140 to work reliably. 250 works for everyone. Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Anssi Hannula authored
commit 904044dd upstream. Commit 9e5f1b27 ("can: xilinx_can: add support for Xilinx CAN FD core") added a new can_bittiming_const structure for CAN FD cores that support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN cores, but the commit did not actually take that into use. Fix that. Tested with CAN FD core on a ZynqMP board. Fixes: 9e5f1b27 ("can: xilinx_can: add support for Xilinx CAN FD core") Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com> Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Naohiro Aota authored
commit c4e0540d upstream. Currently, btrfs does not consult seed devices to start readahead. As a result, if readahead zone is added to the seed devices, btrfs_reada_wait() indefinitely wait for the reada_ctl to finish. You can reproduce the hung by modifying btrfs/163 to have larger initial file size (e.g. xfs_io pwrite 4M instead of current 256K). Fixes: 7414a03f ("btrfs: initial readahead code and prototypes") Cc: stable@vger.kernel.org # 3.2+: ce7791ff: Btrfs: fix race between readahead and device replace/removal Cc: stable@vger.kernel.org # 3.2+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Arnd Bergmann authored
[ Upstream commit 1dac6f5b ] gcc gets a bit confused by the logic in ovl_setup_trap() and can't figure out whether the local 'trap' variable in the caller was initialized or not: fs/overlayfs/super.c: In function 'ovl_fill_super': fs/overlayfs/super.c:1333:4: error: 'trap' may be used uninitialized in this function [-Werror=maybe-uninitialized] iput(trap); ^~~~~~~~~~ fs/overlayfs/super.c:1312:17: note: 'trap' was declared here Reword slightly to make it easier for the compiler to understand. Fixes: 146d62e5 ("ovl: detect overlapping layers") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Miklos Szeredi authored
[ Upstream commit 9179c21d ] NFS mounts can be disconnected from fs root. Don't fail the overlapping layer check because of this. The check is not authoritative anyway, since topology can change during or after the check. Reported-by: Antti Antinoja <antti@fennosys.fi> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: 146d62e5 ("ovl: detect overlapping layers") Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Amir Goldstein authored
[ Upstream commit 146d62e5 ] Overlapping overlay layers are not supported and can cause unexpected behavior, but overlayfs does not currently check or warn about these configurations. User is not supposed to specify the same directory for upper and lower dirs or for different lower layers and user is not supposed to specify directories that are descendants of each other for overlay layers, but that is exactly what this zysbot repro did: https://syzkaller.appspot.com/x/repro.syz?x=12c7a94f400000 Moving layer root directories into other layers while overlayfs is mounted could also result in unexpected behavior. This commit places "traps" in the overlay inode hash table. Those traps are dummy overlay inodes that are hashed by the layers root inodes. On mount, the hash table trap entries are used to verify that overlay layers are not overlapping. While at it, we also verify that overlay layers are not overlapping with directories "in-use" by other overlay instances as upperdir/workdir. On lookup, the trap entries are used to verify that overlay layers root inodes have not been moved into other layers after mount. Some examples: $ ./run --ov --samefs -s ... ( mkdir -p base/upper/0/u base/upper/0/w base/lower lower upper mnt mount -o bind base/lower lower mount -o bind base/upper upper mount -t overlay none mnt ... -o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w) $ umount mnt $ mount -t overlay none mnt ... -o lowerdir=base,upperdir=upper/0/u,workdir=upper/0/w [ 94.434900] overlayfs: overlapping upperdir path mount: mount overlay on mnt failed: Too many levels of symbolic links $ mount -t overlay none mnt ... -o lowerdir=upper/0/u,upperdir=upper/0/u,workdir=upper/0/w [ 151.350132] overlayfs: conflicting lowerdir path mount: none is already mounted or mnt busy $ mount -t overlay none mnt ... -o lowerdir=lower:lower/a,upperdir=upper/0/u,workdir=upper/0/w [ 201.205045] overlayfs: overlapping lowerdir path mount: mount overlay on mnt failed: Too many levels of symbolic links $ mount -t overlay none mnt ... -o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w $ mv base/upper/0/ base/lower/ $ find mnt/0 mnt/0 mnt/0/w find: 'mnt/0/w/work': Too many levels of symbolic links find: 'mnt/0/u': Too many levels of symbolic links Reported-by: syzbot+9c69c282adc4edd2b540@syzkaller.appspotmail.com Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Jaesoo Lee authored
[ Upstream commit c8e8c77b ] The Number of Namespaces (nn) field in the identify controller data structure is defined as u32 and the maximum allowed value in NVMe specification is 0xFFFFFFFEUL. This change fixes the possible overflow of the DIV_ROUND_UP() operation used in nvme_scan_ns_list() by casting the nn to u64. Signed-off-by: Jaesoo Lee <jalee@purestorage.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Dave Martin authored
[ Upstream commit ebcc5928 ] Since GCC 9, the compiler warns about evolution of the platform-specific ABI, in particular relating for the marshaling of certain structures involving bitfields. The kernel is a standalone binary, and of course nobody would be so stupid as to expose structs containing bitfields as function arguments in ABI. (Passing a pointer to such a struct, however inadvisable, should be unaffected by this change. perf and various drivers rely on that.) So these warnings do more harm than good: turn them off. We may miss warnings about future ABI drift, but that's too bad. Future ABI breaks of this class will have to be debugged and fixed the traditional way unless the compiler evolves finer-grained diagnostics. Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Robert Hancock authored
[ Upstream commit 4a60570d ] Some chips have attributes which exist on more than one page but the attribute is not presently marked as paged. This causes the attributes to be generated with the same label, which makes it impossible for userspace to tell them apart. Marking all such attributes as paged would result in the page suffix being added regardless of whether they were present on more than one page or not, which might break existing setups. Therefore, we add a second check which treats the attribute as paged, even if not marked as such, if it is present on multiple pages. Fixes: b4ce237b ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers") Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Eduardo Valentin authored
[ Upstream commit c41dd48e ] Drivers may register to hwmon and request for also registering with the thermal subsystem (HWMON_C_REGISTER_TZ). However, some of these driver, e.g. marvell phy, may be probed from Device Tree or being dynamically allocated, and in the later case, it will not have a dev->of_node entry. Registering with hwmon without the dev->of_node may result in different outcomes depending on the device tree, which may be a bit misleading. If the device tree blob has no 'thermal-zones' node, the *hwmon_device_register*() family functions are going to gracefully succeed, because of-thermal, *thermal_zone_of_sensor_register() return -ENODEV in this case, and the hwmon error path handles this error code as success to cover for the case where CONFIG_THERMAL_OF is not set. However, if the device tree blob has the 'thermal-zones' entry, the *hwmon_device_register*() will always fail on callers with no dev->of_node, propagating -EINVAL. If dev->of_node is not present, calling of-thermal does not make sense. For this reason, this patch checks first if the device has a of_node before going over the process of registering with the thermal subsystem of-thermal interface. And in this case, when a caller of *hwmon_device_register*() with HWMON_C_REGISTER_TZ and no dev->of_node will still register with hwmon, but not with the thermal subsystem. If all the hwmon part bits are in place, the registration will succeed. Fixes: d560168b ("hwmon: (core) New hwmon registration API") Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-hwmon@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Eduardo Valentin <eduval@amazon.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Alexandra Winter authored
[ Upstream commit 33572619 ] Enabling sysfs attribute bridge_hostnotify triggers a series of udev events for the MAC addresses of all currently connected peers. In case no VLAN is set for a peer, the device reports the corresponding MAC addresses with VLAN ID 4096. This currently results in attribute VLAN=4096 for all non-VLAN interfaces in the initial series of events after host-notify is enabled. Instead, no VLAN attribute should be reported in the udev event for non-VLAN interfaces. Only the initial events face this issue. For dynamic changes that are reported later, the device uses a validity flag. This also changes the code so that it now sets the VLAN attribute for MAC addresses with VID 0. On Linux, no qeth interface will ever be registered with VID 0: Linux kernel registers VID 0 on all network interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0. Peers with other OSs could register MACs with VID 0. Fixes: 9f48b9db ("qeth: bridgeport support - address notifications") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Julian Wiedmann authored
[ Upstream commit 0cd6783d ] While qeth_l3 uses netif_keep_dst() to hold onto the dst, a skb's dst may still have been obsoleted (via dst_dev_put()) by the time that we end up using it. The dst then points to the loopback interface, which means the neighbour lookup in qeth_l3_get_cast_type() determines a bogus cast type of RTN_BROADCAST. For IQD interfaces this causes us to place such skbs on the wrong HW queue, resulting in TX errors. Fix-up the various call sites to first validate the dst entry with dst_check(), and fall back accordingly. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Julian Wiedmann authored
[ Upstream commit 72c87976 ] When selecting the cast type of a neighbourless IPv4 skb (eg. on a raw socket), qeth_l3 falls back to the packet's destination IP address. For this case we should classify traffic sent to 255.255.255.255 as broadcast. This fixes DHCP requests, which were misclassified as unicast (and for IQD interfaces thus ended up on the wrong HW queue). Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Christian Brauner authored
[ Upstream commit 1fcd0eb3 ] Define __NR_pidfd_send_signal if it isn't to prevent a potential compilation error. To make pidfd-test compile on all arches, irrespective of whether or not syscall numbers are assigned, define the syscall number to -1. If it isn't defined this will cause the kernel to return -ENOSYS. Fixes: 575a0ae9 ("selftests: add tests for pidfd_send_signal()") Signed-off-by: Christian Brauner <christian@brauner.io> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Lucas Stach authored
[ Upstream commit 283f1e38 ] unmap_udmabuf fails to actually unmap the scatterlist, leaving dangling mappings around. Fixes: fbb0de79 ("Add udmabuf misc device") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Link: http://patchwork.freedesktop.org/patch/msgid/20190604202331.17482-1-l.stach@pengutronix.deSigned-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-