When in hardware lag and the NIC has more than 2 ports when one port
goes down need to distribute the traffic between the remaining
active ports.

For better spread in such cases instead of using 1-to-1 mapping and only
4 slots in the hash, use many.

Each port will have many slots that point to it. When a port goes down
go over all the slots that pointed to that port and spread them between
the remaining active ports. Once the port comes back restore the default
mapping.

We will have number_of_ports * MLX5_LAG_MAX_HASH_BUCKETS slots.
Each MLX5_LAG_MAX_HASH_BUCKETS belong to a different port.
The native mapping is such that:

port 1: The first MLX5_LAG_MAX_HASH_BUCKETS slots are: [1, 1, .., 1]
which means if a packet is hased into one of this slots it will hit the
wire via port 1.

port 2: The second MLX5_LAG_MAX_HASH_BUCKETS slots are: [2, 2, .., 2]
which means if a packet is hased into one of this slots it will hit the
wire via port2.

and this mapping is the same of the rest of the ports.
On a failover, lets say port 2 goes down (port 1, 3, 4 are still up).
the new mapping for port 2 will be:

port 2: The second MLX5_LAG_MAX_HASH_BUCKETS are: [1, 3, 1, 4, .., 4]
which means the mapping was changed from the native mapping to a mapping
that consists of only the active ports.

With this if a port goes down the traffic will be split between the
active ports randomly
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Combine dmesg lag prints into a single function.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Increase the define MLX5_MAX_PORTS to 4 as the driver is ready
to support NICs with 4 ports.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Refactor the entire lag code to use ldev->ports instead of hard-coded
defines (like MLX5_MAX_PORTS) for its operations.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Downstream patches will add support for lag over 4 ports.
In that mode we will only use hash as the uplink selection method.
Using hash instead of queue affinity (before this patch) offers key
advantages like:

- Align ports selection method with the method used by the bond device

- Better packets distribution where a single queue can transmit from
  multiple ports (with queue affinity a queue is bound to a single port
  regardless of the packet being sent).

- In case of failover we traffic is split between multiple ports and not
  a single one like in queue affinity.

Going forward it was decided that queue affinity will be deprecated
as using hash provides a better user experience which means on 4 ports
HCAs hash will always be used.

Future work will add hash support for 2 ports HCAs as well.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

E-Switch currently doesn't support more than 2 E-Switch managers
being aggregated under a single hardware lag. Have specific checks
to disallow creating lag when the code doesn't support it.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Store the number of lag ports inside the lag object. Lag object is a single
shared object managing the lag state of multiple mlx5 devices on the same
physical HCA.

Downstream patches will allow hardware lag to be created over devices with
more than 2 ports.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When search for a peer lag device we can filter based on that
device's capabilities.

Downstream patch will be less strict when filtering compatible devices
and remove the limitation where we require exact MLX5_MAX_PORTS and
change it to a range.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Use a lag specific lock instead of depending on external locks to
synchronise the lag creation/destruction.

With this, taking E-Switch mode lock is no longer needed for syncing
lag logic.

Cleanup any dead code that is left over and don't export functions that
aren't used outside the E-Switch core code.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

There is no need to expose E-Switch function for something that can be
checked with already present API inside lag code.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Devcom API is intended to be used between 2 devices only add this
implied assumption into the code and check when it's no true.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Downstream patches will add support for hardware lag with
more than 2 ports. Add a way for users to query the number of lag ports.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, health recovery will reload driver to recover it from fatal
errors. During the driver's load process, it would wait for FW to set the
pre-init bit for up to 120 seconds, beyond this threshold it would abort
the load process. In some cases, such as a FW upgrade on the DPU, this
timeout period is insufficient, and the user has no way to recover the
host device.

To solve this issue, introduce a new FW pre-init timeout for health
recovery, which is set to 2 hours.

The timeout for devlink reload and probe will use the original one because
they are user triggered flows, and therefore should not have a
significantly long timeout, during which the user command would hang.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, removing a device needs to get the driver interface lock before
doing any cleanup. If the driver is waiting in a loop for FW init, there
is no way to cancel the wait, instead the device cleanup waits for the
loop to conclude and release the lock.

To allow immediate response to remove device commands, check the TEARDOWN
flag while waiting for FW init, and exit the loop if it has been set.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Simon Horman says:

====================
nfp: support Corigine PCIE vendor ID

Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. This patch extends the driver to also support NFP
chips, which at this point are assumed to be otherwise identical from
a software perspective, that have Corigine's PCIE vendor ID (0x1da8).

This patchset begins by cleaning up strings to make them:
* Vendor neutral for the NFP chip
* Relate to Corigine for the driver itself

It then adds support to the driver for the Corigine's PCIE vendor ID
====================

Link: https://lore.kernel.org/r/20220508173816.476357-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. This patch extends the driver to also support NFP
chips, which at this point are assumed to be otherwise identical from
a software perspective, that have Corigine's PCIE vendor ID (0x1da8).

Also, Rename the macro definitions PCI_DEVICE_ID_NERTONEOME_NFPXXXX
to PCI_DEVICE_ID_NFPXXXX, as they are now used in conjunction with two
PCIE vendor IDs.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. In preparation for extending the to also support NFP
chips that have Corigine's PCIE vendor ID (0x1da8) make printk statements
relating to the chip vendor neutral.

An alternate approach is to set the string based on the PCI vendor ID.
In our judgement this proved to cumbersome so we have taken this simpler
approach.

Update strings relating to the driver to use Corigine, who have taken
over maintenance of the driver.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2022-05-06

Marcin Szycik says:

This patchset adds support for systemd defined naming scheme for port
representors, as well as re-enables displaying PCI bus-info in ethtool.

bus-info information has previously been removed from ethtool for port
representors, as a workaround for a bug in lshw tool, where the tool would
sometimes display wrong descriptions for port representors/PF. Now the bug
has been fixed in lshw tool [1].

Removing the workaround can be considered a regression (user might be
running an older, unpatched version of lshw) (see [2] for discussion).
However, calling SET_NETDEV_DEV also produces the same effect as removing
the workaround, i.e. lshw is able to access PCI bus-info (this time not
via ethtool, but in some other way) and the bug can occur.

Adding SET_NETDEV_DEV is important, as it greatly improves netdev naming -
- port representors are named based on PF name. Currently port representors
are named "ethX", which might be confusing, especially when spawning VFs on
multiple PFs. Furthermore, it's currently harder to determine to which PF
does a particular port representor belong, as bus-info is not shown in
ethtool.

Consider the following three cases:

Case 1: current code - driver workaround in place, no SET_NETDEV_DEV,
lshw with or without fix. Port representors are not displayed because they
don't have bus-info (the workaround), PFs are labelled correctly:

$ sudo ./lshw -c net -businfo
Bus info          Device      Class          Description
========================================================
pci@0000:02:00.0  ens6f0      network        Ethernet Controller E810-XXV for SFP <-- PF
pci@0000:02:00.1  ens6f1      network        Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0  ens6f0v0    network        Ethernet Adaptive Virtual Function <-- VF
pci@0000:02:01.1  ens6f0v1    network        Ethernet Adaptive Virtual Function
...

Case 2: driver workaround in place, SET_NETDEV_DEV, no lshw fix. Port
representors have predictable names. lshw is able to get bus-info because
of SET_NETDEV_DEV and netdevs CAN be mislabelled:

$ sudo ./lshw -c net -businfo
Bus info          Device           Class          Description
=============================================================
pci@0000:02:00.0  ens6f0npf0vf60   network        Ethernet Controller E810-XXV for SFP <-- mislabeled port representor
pci@0000:02:00.1  ens6f1           network        Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0  ens6f0v0         network        Ethernet Adaptive Virtual Function
pci@0000:02:01.1  ens6f0v1         network        Ethernet Adaptive Virtual Function
...
pci@0000:02:00.0  ens6f0npf0vf26   network        Ethernet interface
pci@0000:02:00.0  ens6f0           network        Ethernet interface <-- mislabeled PF
pci@0000:02:00.0  ens6f0npf0vf81   network        Ethernet interface
...
$ sudo ethtool -i ens6f0npf0vf60
driver: ice
...
bus-info:
...

Output of lshw would be the same with workaround removed; it does not
change the fact that lshw labels netdevs incorrectly, while at the same
time it prevents ethtool from displaying potentially useful data
(bus-info).

Case 3: workaround removed, SET_NETDEV_DEV, lshw fix:

$ sudo ./lshw -c net -businfo
Bus info          Device           Class          Description
=============================================================
pci@0000:02:00.0  ens6f0npf0vf73   network        Ethernet Controller E810-XXV for SFP
pci@0000:02:00.1  ens6f1           network        Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0  ens6f0v0         network        Ethernet Adaptive Virtual Function
pci@0000:02:01.1  ens6f0v1         network        Ethernet Adaptive Virtual Function
...
pci@0000:02:00.0  ens6f0npf0vf5    network        Ethernet Controller E810-XXV for SFP
pci@0000:02:00.0  ens6f0           network        Ethernet Controller E810-XXV for SFP
pci@0000:02:00.0  ens6f0npf0vf60   network        Ethernet Controller E810-XXV for SFP
...
$ sudo ethtool -i ens6f0npf0vf73
driver: ice
...
bus-info: 0000:02:00.0
...

In this case poort representors have predictable names, netdevs are not
mislabelled in lshw, and bus-info is shown in ethtool.

[1] https://ezix.org/src/pkg/lshw/commit/9bf4e4c9c1
[2] https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20220321144731.3935-1-marcin.szycik@linux.intel.com

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  Revert "ice: Hide bus-info in ethtool for PRs in switchdev mode"
  ice: link representors to PCI device
====================

Link: https://lore.kernel.org/r/20220506180052.5256-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eliminate the follow smatch warning:

net/rose/rose_route.c:1136 rose_node_show() warn: inconsistent
indenting.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220507034207.18651-1-jiapeng.chong@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Guangbin Huang says:

====================
net: hns3: updates for -next

This series includes some updates for the HNS3 ethernet driver.

Change logs:
V1 -> V2:
 - Fix some sparse warnings of patch 3# and 4#.
 - Add patch #6 to fix sparse warnings of incorrect type of argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The argument rss_ind_tbl_size is type u16 in function definition of
hclge_comm_get_rss_indir_tbl(), but it is set to type __le16 in function
declaration by mistake, so fix it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new mailbox opcode to query map relation between
vf ring and vector.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch uses __le16/__32 to define mailbox data structures. Then byte
order conversion are added for mailbox messages from VF to PF.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, hns3 mailbox processing between PF and VF missed to convert
message byte order and use data type u16 instead of __le16 for mailbox
data process. These processes may cause problems between different
architectures.

So this patch uses __le16/__le32 data type to define mailbox data
structures. To be compatible with old hns3 driver, these structures use
one-byte alignment. Then byte order conversions are added to mailbox
messages from PF to VF.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vector0 is used for common interrupt control events and is
irrelevant to performance. Currently, the driver sets the
default affinity of vector0 to NUMA nodes, which is unnecessary.
Therefore, the default setting is removed, and the driver does
not set the affinity for vector0.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When set tx-buf-size as 0 by ethtool, hns3_init_tx_spare_buffer()
will return directly and priv->ring->tx_spare->len is uninitialized,
then print function access priv->ring->tx_spare->len will cause
this issue.

When set tx-buf-size as 0 by ethtool, the print function will
print 0 directly and not access priv->ring->tx_spare->len.

Fixes: 2373b35c ("net: hns3: add log for setting tx spare buf size")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuiko Oshino says:

====================
net: phy: add LAN8742 phy support

add LAN8742 phy support
update LAN88xx phy ID and phy ID mask so that it can coexist with LAN8742

The current phy IDs on the available hardware.
    LAN8742 0x0007C130, 0x0007C131
    LAN88xx 0x0007C132

v3->v4:
- fixed the one tab missing issue in the smsc.c.

v2->v3:
-added comments about the 0xfffffff2 mask that is for the differentiation and the future revisions.

v1->v2:
-removed "REVIEW REQUEST3" from the PATCH 1/2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current phy IDs on the available hardware.
        LAN8742 0x0007C130, 0x0007C131
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

update LAN88xx phy ID and phy ID mask because the existing code conflicts with the LAN8742 phy.

The current phy IDs on the available hardware.
        LAN8742 0x0007C130, 0x0007C131
        LAN88xx 0x0007C132
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Oleksij Rempel says:

====================
add ti dp83td510 support

changes v4:
- dp83td510: remove unused variables
- s/base1/baset1
- s/genphy_c45_baset1_read_master_slave/genphy_c45_pma_baset1_read_master_slave

changes v3:
- export reusable code snippets and make use of it in the dp83td510
  driver

changes v2:
- rewrite the driver reduce usage of common code and to reduce amount of
  quirks.
- add genphy_c45_baset1_an_config_aneg fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The DP83TD510E is an ultra-low power Ethernet physical layer transceiver
that supports 10M single pair cable.

This driver was tested with NXP SJA1105, STMMAC and ASIX AX88772B USB Ethernet
controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export genphy_c45_baset1_read_status() to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since MDIO_PMA_PMD_BT1_CTRL register shows actual configuration (and
forced state configuration is equal to the state), we should show
this configuration for ethtool.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move baset1 specific part of genphy_c45_read_pma() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not change default master/slave forced configuration if no changes was
requested.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move baset1 specific part of genphy_c45_pma_setup_forced() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not change default master/slave autoneg configuration if no
changes was requested.

Fixes: 3da8ffd8 ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alaa Mohamed says:

====================
propagate extack to vxlan_fdb_delete

In order to propagate extack to vxlan_fdb_delete and vxlan_fdb_parse,
add extack to .ndo_fdb_del and edit all fdb del handelers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds extack msg support to vxlan_fdb_delete and vxlan_fdb_parse.
extack is used to propagate meaningful error msgs to the user of vxlan
fdb netlink api
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack support to .ndo_fdb_del in netdevice.h and
all related methods.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>