The newly introduced 'cpu' variable is only used inside of an optional
block, so we get a warning without CONFIG_SCSI_LPFC_DEBUG_FS:

drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_io_cmd_wqe_cmpl':
drivers/scsi/lpfc/lpfc_nvme.c:968:30: error: unused variable 'cpu' [-Werror=unused-variable]
  uint32_t code, status, idx, cpu;

Move the declaration into the same block to avoid the warning.

Fixes: 63df6d63 ("scsi: lpfc: Adapt cpucheck debugfs logic to Hardware Queues")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Switch to bitmap_zalloc() to show clearly what we are allocating.  Besides
that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In "XFS over network block device" scenario XFS can create IO requests with
slab-based XFS metadata. During processing such requests tcp_sendpage() can
merge skb fragments with neighbour slab objects.

If receiving side is located on the same host tcp_recvmsg() can trigger
BUG_ON in hardening check and crash the host with following message:

usercopy: kernel memory exposure attempt detected
		from XXXXXXXX (kmalloc-512) (1024 bytes)

This patch redirect such requests from sednpage to sendmsg path.  The
problem is similar to one described in recent commit 7e241f64
("libceph: fall back to sendmsg for slab pages")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Depending on the target architecture and configuration, both phys_addr_t
and dma_addr_t may be smaller than 'long long', so we get a warning when
printing either of them using the %llx format string:

drivers/scsi/qla2xxx/qla_iocb.c: In function 'qla24xx_walk_and_build_prot_sglist':
drivers/scsi/qla2xxx/qla_iocb.c:1140:46: error: format '%llx' expects argument of type 'long long unsigned int', but argument 6 has type 'dma_addr_t' {aka 'unsigned int'} [-Werror=format=]
         "%s: page boundary crossing (phys=%llx len=%x)\n",
                                           ~~~^
                                           %x
         __func__, sle_phys, sg->length);
                   ~~~~~~~~
drivers/scsi/qla2xxx/qla_iocb.c:1180:29: error: format '%llx' expects argument of type 'long long unsigned int', but argument 7 has type 'dma_addr_t' {aka 'unsigned int'} [-Werror=format=]
        "%s: sg[%x] (phys=%llx sglen=%x) ldma_sg_len: %x dif_bundl_len: %x ldma_needed: %x\n",
                          ~~~^

There are special %pad and %pap format strings in Linux that we could use
here, but since the driver already does 64-bit arithmetic on the values,
using a plain 'u64' seems more consistent here.

Note: A possible related issue may be that the driver possibly checks the
wrong kind of overflow: when an IOMMU is in use, buffers that cross a
32-bit boundary in physical addresses would still be mapped into dma
addresses within the low 4GB space, so I suspect that we actually want to
check sg_dma_address() instead of sg_phys() here.

Fixes: 50b81275 ("scsi: qla2xxx: Fix DMA error when the DIF sg buffer crosses 4GB boundary")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The patch that replaced io channels for hdw_queues now reports the
following static checker warning:

drivers/scsi/lpfc/lpfc_init.c:11136 lpfc_sli4_hba_unset()
 error: we previously assumed 'phba->pport' could be null (see line 11074)

Resolve by adding a pport NULL check.

[mkp: tag tweak]

Fixes: cdb42bec ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu"_
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The outer routine lpfc_sli_issue_iocb(), which decomposes into the
SLI3 (s3) or SLI4 (s4) subroutines takes out the locks. For s3, it takes
out the hbalock. For s4, it takes out the ring_lock. The lockdep check in
the s3 and s4 subroutines both check hbalock, which is incorrect for s4.

Revise the s4 subroutine to lockdep check the ring_lock.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Without CONFIG_OF, the of_match_node() helper does not evaluate its
argument, and the compiler warns about the unused variable:

drivers/scsi/ufs/ufs-hisi.c: In function 'ufs_hisi_probe':
drivers/scsi/ufs/ufs-hisi.c:673:17: error: unused variable 'dev' [-Werror=unused-variable]

Rework this code to pass the data directly, and while we're at it,
correctly handle the const pointers.

Fixes: 653fcb07 ("scsi: ufs: Add HI3670 SoC UFS driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When trying to display tgt_counters in the debugfs, a panic can result.

There is no null check for qpair after it is assigned in the for-loop.
Unless vha->hw->queue_pair_map array is completely filled with entries, the
system will panic dereferencing a null pointer.
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas takes 1+ seconds to load while waiting for firmware:

[2.822603] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[3.871003] megaraid_sas 0000:03:00.0: FW now in Ready state

This is due to the following loop in megasas_transition_to_ready(), which
waits a minimum of 1 second, even though the FW becomes ready in tens of
millisecs:

        /*
         * The cur_state should not last for more than max_wait secs
         */
        for (i = 0; i < max_wait; i++) {
                ...
                msleep(1000);
        ...
        dev_info(&instance->pdev->dev, "FW now in Ready state\n");

This is a regression, caused by a change of the msleep granularity from 1
to 1000 due to concern about waiting too long on systems with coarse
jiffies.

To fix, increase iterations and use msleep(20), which results in:

[2.670627] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[2.739386] megaraid_sas 0000:03:00.0: FW now in Ready state

Fixes: fb2f3e96d80f ("scsi: megaraid_sas: Fix msleep granularity")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

genlmsg_multicast_allns now returns the correct statuses when a message is
sent to a listener. However in the case of adding a device we want to wait
for the listener otherwise we may miss the the device during startup.
Signed-off-by: Cathy Avery <cavery@redhat.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The virtio scsi spec defines struct virtio_scsi_ctrl_tmf as a set of
device-readable records and a single device-writable response entry:

    struct virtio_scsi_ctrl_tmf
    {
        // Device-readable part
        le32 type;
        le32 subtype;
        u8 lun[8];
        le64 id;
        // Device-writable part
        u8 response;
    }

The above should be organised as two descriptor entries (or potentially
more if using VIRTIO_F_ANY_LAYOUT), but without any extra data after "le64
id" or after "u8 response".

The Linux driver doesn't respect that, with virtscsi_abort() and
virtscsi_device_reset() setting cmd->sc before calling virtscsi_tmf().  It
results in the original scsi command payload (or writable buffers) added to
the tmf.

This fixes the problem by leaving cmd->sc zeroed out, which makes
virtscsi_kick_cmd() add the tmf to the control vq without any payload.

Cc: stable@vger.kernel.org
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When the HARDWARE_ERROR/0x3e/0x1 case is triggered, the logical volume
is offlined.  When reading the kernel log, the reason why the device
got offlined isn't reported to the user.  This situation makes it
difficult for admins to root cause.

Log a message when this condition occurs.

[mkp: tweaked commit message]
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

T6 adapters generates DDP completion message on receiving all iSCSI pdus in
a sequence. Because of this, driver can not keep track of tcp sequence
number for T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Instead of using viid to get pf number, directly get pf number from
lldi->pf.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):

[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access     IBM      2107900          .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838]  sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured

Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.

There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.

Here is the contexts for the three functions so far:

    scsi_alloc_sdev()
        scsi_probe_and_add_lun()
            scsi_sequential_lun_scan()
                __scsi_scan_target()
                    scsi_scan_target()
                        mutex_lock()
                    scsi_scan_channel()
                        scsi_scan_host_selected()
                            mutex_lock()
            scsi_report_lun_scan()
                __scsi_scan_target()
    	            ...
            __scsi_add_device()
                mutex_lock()
            __scsi_scan_target()
                ...
        scsi_report_lun_scan()
            ...
        scsi_get_host_dev()
            mutex_lock()

    scsi_probe_and_add_lun()
        ...

    scsi_add_lun()
        scsi_probe_and_add_lun()
            ...

So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix the following warnings by adding the proper missing breaks:

drivers/scsi/mpt3sas/mpt3sas_base.c: In function  _base_display_OEMs_branding :
drivers/scsi/mpt3sas/mpt3sas_base.c:3548:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
    switch (ioc->pdev->subsystem_device) {
    ^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3566:3: note: here
   case MPI2_MFGPAGE_DEVID_SAS2308_2:
   ^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3567:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
    switch (ioc->pdev->subsystem_device) {
    ^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3601:3: note: here
   case MPI25_MFGPAGE_DEVID_SAS3008:
   ^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3735:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
    switch (ioc->pdev->subsystem_device) {
    ^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3745:3: note: here
   case MPI2_MFGPAGE_DEVID_SAS2308_2:
   ^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3746:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
    switch (ioc->pdev->subsystem_device) {
    ^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3768:3: note: here
   default:
   ^~~~~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add missing break statement and fix identation issue.

This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.

Fixes: 9cb62fa2 ("aacraid: Log firmware AIF messages")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

No users left, kill it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Use request tag instead of the serial number when printing out logging
messages.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Use the request tag for logging instead of the scsi command serial number.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Drop references to scsi_cmnd->serial_number.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Negative constant left-shift is undefined behaviour in the C standard, and
as such newer versions of clang (at least) warn against it. GCC supports it
for a long time, but it would be better to remove it and rely on defined
behaviour.

My understanding is "~(-1 << N)" in 2's complement is intended to generate
a bit pattern of zeroes ending with N '1' bits. The same can be achieved by
"(1 << N) - 1" in a well-defined way, so switch to it to remove the
warning.

Tested: building a kernel with generic SCSI tape, and checking basic
operations (mt status, mt eject) on a real LTO unit. Cannot test the osst
driver.
Signed-off-by: Iustin Pop <iustin@k1024.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add this functionality, placing the descriptor being read in the actual
data buffer in the bio.

That is, for both read and write descriptors query upiu, we are using the
job's request_payload.  This in turn, is mapped back in user land to the
applicable sg_io_v4 xferp: dout_xferp for write descriptor, and din_xferp
for read descriptor.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Allow to read descriptors via raw upiu. This in fact was forbidden just as
a precaution, as ufs-bsg actually enforces which functionality is
supported.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When we had a write descriptor query upiu, we appended the descriptor right
after the bsg request.  This was fine as the bsg driver allows to allocate
whatever buffer we needed in its job request.

Still, the proper way to deliver payload, however small (we only write
config descriptors of 144 bytes), is by using the job request payload data
buffer.

So change this ABI now, while ufs-bsg is still new, and nobody is actually
using it.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The UFSHC driver defines a few quirks that are not used anywhere:

UFS_DEVICE_QUIRK_BROKEN_LCC
UFS_DEVICE_NO_VCCQ
UFS_DEVICE_QUIRK_NO_LINK_OFF
UFS_DEVICE_NO_FASTAUTO

Let's remove them.
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This reverts commit 60f01870.

There was one conflict in drivers/scsi/ufs/ufshcd.c

<<<<<<< HEAD
	/* Init check for device descriptor sizes */
	ufshcd_init_desc_sizes(hba);

	ret = ufs_get_device_desc(hba, &card);
	if (ret) {
		dev_err(hba->dev, "%s: Failed getting device info. err = %d\n",
			__func__, ret);
		goto out;
	}

	ufs_fixup_device_setup(hba, &card);
	ufshcd_tune_unipro_params(hba);

	ret = ufshcd_set_vccq_rail_unused(hba,
		(hba->dev_quirks & UFS_DEVICE_NO_VCCQ) ? true : false);
	if (ret)
		goto out;

=======
	ufs_advertise_fixup_device(hba);
>>>>>>> parent of 60f01870... scsi: ufs: disable vccq if it's not needed by UFS device

Resolution: keep HEAD, and delete the ufshcd_set_vccq_rail_unused() call
and corresponding error-handling code.

Clean up loose ends in a follow-up patch.

60f01870 introduced a small power optimization: ignore the vccq load
specified in the UFSHC DT node when said host controller is connected to
specific Flash chips (currently, Samsung and Hynix).

Unfortunately, this optimization breaks UFS on systems where vccq powers
not only the Flash chip, but the host controller as well, such as APQ8098
MEDIABOX or MTP8998:

[    3.929877] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[    5.433815] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[    6.937771] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[    6.937866] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr_retry: query attribute, idn 13, failed with error -11 after 3 retires
[    6.946412] ufshcd-qcom 1da4000.ufshc: ufshcd_disable_auto_bkops: failed to enable exception event -11
[    6.957972] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1587 failed 3 retries
[    6.967181] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1586 failed 3 retries
[    6.975025] ufshcd-qcom 1da4000.ufshc: ufshcd_get_max_pwr_mode: invalid max pwm tx gear read = 0
[    6.982755] ufshcd-qcom 1da4000.ufshc: ufshcd_probe_hba: Failed getting max supported power mode
[    8.505770] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[   10.009807] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[   11.513766] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[   11.513861] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry: query attribute, opcode 5, idn 3, failed with error -11 after 3 retires
[   13.049807] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[   14.553768] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[   16.057767] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[   16.057872] ufshcd-qcom 1da4000.ufshc: ufshcd_read_desc_param: Failed reading descriptor. desc_id 8, desc_index 0, param_offset 0, ret -11
[   16.067109] ufshcd-qcom 1da4000.ufshc: ufshcd_init_icc_levels: Failed reading power descriptor.len = 98 ret = -11
[   37.073787] ufshcd-qcom 1da4000.ufshc: link startup failed 1

In my opinion, the rationale for the original patch is questionable.  If
neither the UFSHC, nor the Flash chip, require any load from vccq, then
that power rail should simply not be specified at all in the DT.

Working around that fact in the driver is detrimental, as evidenced by the
failure to initialize the host controller on MSM8998.
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'wait_and_poll':
drivers/scsi/megaraid/megaraid_sas_fusion.c:936:25: warning:
 variable 'fusion' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_sync_map_info':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1329:6: warning:
 variable 'size_sync_info' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_init_adapter_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1639:39: warning:
 variable 'reg_set' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_is_prp_possible':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1925:25: warning:
 variable 'fusion' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_make_prp_nvme':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2047:25: warning:
 variable 'fusion' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_ldio_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2620:42: warning:
 variable 'req_desc' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_and_issue_cmd_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:3245:25: warning:
 variable 'fusion' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_task_abort_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4398:25: warning:
 variable 'fusion' set but not used [-Wunused-but-set-variable]

drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_reset_target_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4484:25: warning:
 variable 'fusion' set but not used [-Wunused-but-set-variable]

They're not used anymore and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Those are no longer in use since commit 242f9dcb
("block: unify request timeout handling").
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

It was reported that some devices report an OPTIMAL TRANSFER LENGTH of
0xFFFF blocks. That looks bogus, especially for a device with a
4096-byte physical block size.

Ignore OPTIMAL TRANSFER LENGTH if it is not a multiple of the device's
reported physical block size.

To make the sanity checking conditionals more readable--and to
facilitate printing warnings--relocate the checking to a helper
function. No functional change aside from the printks.

Cc: <stable@vger.kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199759Reported-by: Christoph Anton Mitterer <calestyo@scientia.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Nic has been absent for a while and target changes now go through the SCSI
tree. To avoid confusion wrt. the NVMe target, clarify that this entry
refers to the SCSI target subsystem.

Also add patchwork links for both SCSI initiator and target.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

commit 1917d42d ("fcoe: use enum for fip_mode") introduces a separate
enum for the fip_mode that shall be used during initialisation handling
until it is passed to fcoe_ctrl_link_up to set the initial fip_state.  That
change was incomplete and gcc quietly converted in various places between
the fip_mode and the fip_state enum values with implicit enum conversions,
which fortunately cannot cause any issues in the actual code's execution.

clang however warns about these implicit enum conversions in the scsi
drivers. This commit consolidates the use of the two enums, guided by
clang's enum-conversion warnings.

This commit now completes the use of the fip_mode: It expects and uses
fip_mode in {bnx2fc,fcoe}_interface_create and fcoe_ctlr_init, and it calls
fcoe_ctrl_set_set() with the correct values in fcoe_ctlr_link_up().  It
also breaks the association between FIP_MODE_AUTO and FIP_ST_AUTO to
indicate these two enums are distinct.

Link: https://github.com/ClangBuiltLinux/linux/issues/151
Fixes: 1917d42d ("fcoe: use enum for fip_mode")
Reported-by: Dmitry Golovin <dima@golovin.in>
Original-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
CC: Lukas Bulwahn <lukas.bulwahn@gmail.com>
CC: Nick Desaulniers <ndesaulniers@google.com>
CC: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

when create DMA pool for cmd frames failed, we should return -ENOMEM,
instead of 0.
In some case in:

    megasas_init_adapter_fusion()

    -->megasas_alloc_cmds()
       -->megasas_create_frame_pool
          create DMA pool failed,
        --> megasas_free_cmds() [1]

    -->megasas_alloc_cmds_fusion()
       failed, then goto fail_alloc_cmds.
    -->megasas_free_cmds() [2]

we will call megasas_free_cmds twice, [1] will kfree cmd_list,
[2] will use cmd_list.it will cause a problem:

Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd = ffffffc000f70000
[00000000] *pgd=0000001fbf893003, *pud=0000001fbf893003,
*pmd=0000001fbf894003, *pte=006000006d000707
Internal error: Oops: 96000005 [#1] SMP
 Modules linked in:
 CPU: 18 PID: 1 Comm: swapper/0 Not tainted
 task: ffffffdfb9290000 ti: ffffffdfb923c000 task.ti: ffffffdfb923c000
 PC is at megasas_free_cmds+0x30/0x70
 LR is at megasas_free_cmds+0x24/0x70
 ...
 Call trace:
 [<ffffffc0005b779c>] megasas_free_cmds+0x30/0x70
 [<ffffffc0005bca74>] megasas_init_adapter_fusion+0x2f4/0x4d8
 [<ffffffc0005b926c>] megasas_init_fw+0x2dc/0x760
 [<ffffffc0005b9ab0>] megasas_probe_one+0x3c0/0xcd8
 [<ffffffc0004a5abc>] local_pci_probe+0x4c/0xb4
 [<ffffffc0004a5c40>] pci_device_probe+0x11c/0x14c
 [<ffffffc00053a5e4>] driver_probe_device+0x1ec/0x430
 [<ffffffc00053a92c>] __driver_attach+0xa8/0xb0
 [<ffffffc000538178>] bus_for_each_dev+0x74/0xc8
  [<ffffffc000539e88>] driver_attach+0x28/0x34
 [<ffffffc000539a18>] bus_add_driver+0x16c/0x248
 [<ffffffc00053b234>] driver_register+0x6c/0x138
 [<ffffffc0004a5350>] __pci_register_driver+0x5c/0x6c
 [<ffffffc000ce3868>] megasas_init+0xc0/0x1a8
 [<ffffffc000082a58>] do_one_initcall+0xe8/0x1ec
 [<ffffffc000ca7be8>] kernel_init_freeable+0x1c8/0x284
 [<ffffffc0008d90b8>] kernel_init+0x1c/0xe4
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch fixes warning seen when BLK-MQ is enabled and hardware does not
support MQ. This will result into driver requesting MSIx vectors which are
equal or less than pre_desc via PCI IRQ Affinity infrastructure.

    [   19.746300] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 10.00.00.12-k.
    [   19.746599] qla2xxx [0000:02:00.0]-001d: : Found an ISP2432 irq 18 iobase 0x(____ptrval____).
    [   20.203186] ------------[ cut here ]------------
    [   20.203306] WARNING: CPU: 8 PID: 268 at drivers/pci/msi.c:1273 pci_irq_get_affinity+0xf4/0x120
    [   20.203481] Modules linked in: tg3 ptp qla2xxx(+) pps_core sg libphy scsi_transport_fc flash loop autofs4
    [   20.203700] CPU: 8 PID: 268 Comm: systemd-udevd Not tainted 5.0.0-rc5-00358-gdf3865f8 #113
    [   20.203830] Call Trace:
    [   20.203933]  [0000000000461bb0] __warn+0xb0/0xe0
    [   20.204090]  [00000000006c8f34] pci_irq_get_affinity+0xf4/0x120
    [   20.204219]  [000000000068c764] blk_mq_pci_map_queues+0x24/0x120
    [   20.204396]  [00000000007162f4] scsi_map_queues+0x14/0x40
    [   20.204626]  [0000000000673654] blk_mq_update_queue_map+0x94/0xe0
    [   20.204698]  [0000000000676ce0] blk_mq_alloc_tag_set+0x120/0x300
    [   20.204869]  [000000000071077c] scsi_add_host_with_dma+0x7c/0x300
    [   20.205419]  [00000000100ead54] qla2x00_probe_one+0x19d4/0x2640 [qla2xxx]
    [   20.205621]  [00000000006b3c88] pci_device_probe+0xc8/0x160
    [   20.205697]  [0000000000701c0c] really_probe+0x1ac/0x2e0
    [   20.205770]  [0000000000701f90] driver_probe_device+0x50/0x100
    [   20.205843]  [0000000000702134] __driver_attach+0xf4/0x120
    [   20.205913]  [0000000000700644] bus_for_each_dev+0x44/0x80
    [   20.206081]  [0000000000700c98] bus_add_driver+0x198/0x220
    [   20.206300]  [0000000000702950] driver_register+0x70/0x120
    [   20.206582]  [0000000010248224] qla2x00_module_init+0x224/0x284 [qla2xxx]
    [   20.206857] ---[ end trace b1de7a3f79fab2c2 ]---

The fix is to check if the hardware does not have Multi Queue capabiltiy,
use pci_alloc_irq_vectors() call instead of pci_alloc_irq_affinity().

Fixes: f664a3cc ("scsi: kill off the legacy IO path")
Cc: stable@vger.kernel.org #4.19
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch adds new firmware dump template entries for ISP27XX firmware
dump.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch fixes following checkpatch ERROR

 ERROR: space prohibited before that ',' (ctx:WxW)

No change is functionality due to this patch.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Current code hard codes marker request to use request and response queue
0. This patch make use of the qpair as the path to access the
request/response queues.  It allows marker to be place on any hardware
queue.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Prevent user from sending commands through sysfs while FW is not running or
reset is in progress.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch adds sysfs node

1. There is a new sysfs node port_speed
2. The possible values are 2(Auto neg), 8, 16, 32
3. A value outside of the above defaults to Auto neg
4. Any update to the setting causes a link toggle
5. This feature is currently only for ISP27xx
Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>