Pull SCSI fixes from James Bottomley:
 "Two patches, both in drivers.

  The iscsi one is fixing the cpumask issue you commented on and the ufs
  one is a late arriving fix for conditions that can occur in Host
  Performance Booster reads"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: core: Fix referencing invalid rsp field
  scsi: target: Fix incorrect use of cpumask_t

Pull kvm fixes from Paolo Bonzini:
 "ARM:

   - Correctly expose GICv3 support even if no irqchip is created so
     that userspace doesn't observe it changing pointlessly (fixing a
     regression with QEMU)

   - Don't issue a hypercall to set the id-mapped vectors when protected
     mode is enabled (fix for pKVM in combination with CPUs affected by
     Spectre-v3a)

  x86 (five oneliners, of which the most interesting two are):

   - a NULL pointer dereference on INVPCID executed with paging
     disabled, but only if KVM is using shadow paging

   - an incorrect bsearch comparison function which could truncate the
     result and apply PMU event filtering incorrectly. This one comes
     with a selftests update too"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86/mmu: fix NULL pointer dereference on guest INVPCID
  KVM: x86: hyper-v: fix type of valid_bank_mask
  KVM: Free new dirty bitmap if creating a new memslot fails
  KVM: eventfd: Fix false positive RCU usage warning
  selftests: kvm/x86: Verify the pmu event filter matches the correct event
  selftests: kvm/x86: Add the helper function create_pmu_event_filter
  kvm: x86/pmu: Fix the compare function used by the pmu event filter
  KVM: arm64: Don't hypercall before EL2 init
  KVM: arm64: vgic-v3: Consistently populate ID_AA64PFR0_EL1.GIC
  KVM: x86/mmu: Update number of zapped pages even if page list is stable

Pull clk fixes from Stephen Boyd:
 "Three clk driver fixes to close out the release

   - Fix a divider calculation breaking boot on Broadcom bcm2835

   - Fix HDMI output on Tanix TX6 mini board by reverting a patch

   - Fix clk_set_rate_range() calls on at91 by considering the range
     while calculating the divisor"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: at91: generated: consider range when calculating best rate
  Revert "clk: sunxi-ng: sun6i-rtc: Add support for H6"
  clk: bcm2835: fix bcm2835_clock_choose_div

Pull drm fixes from Dave Airlie:
 "Few final fixes for 5.18, one amdgpu, core dp mst leak fix, dma-buf
  two fixes, and i915 has a few fixes, one for a regression on older
  GM45 chipsets,

  dma-buf:
   - ioctl userspace use fix
   - fix dma-buf sysfs name generation

  core:
   - dp/mst leak fix

  amdgpu:
   - suspend/resume regression fix

  i915:
   - fix for #5806: GPU hangs and display artifacts on Intel GM45
   - reject DMC with out-of-spec MMIO
   - correctly mark guilty contexts on GuC reset"

* tag 'drm-fixes-2022-05-21' of git://anongit.freedesktop.org/drm/drm:
  drm/i915: Use i915_gem_object_ggtt_pin_ww for reloc_iomap
  drm/amd: Don't reset dGPUs if the system is going to s2idle
  drm/dp/mst: fix a possible memory leak in fetch_monitor_name()
  dma-buf: fix use of DMA_BUF_SET_NAME_{A,B} in userspace
  i915/guc/reset: Make __guc_reset_context aware of guilty engines
  drm/i915/dmc: Add MMIO range restrictions
  dma-buf: ensure unique directory name for dmabuf stats

Merge tag 'drm-intel-fixes-2022-05-20' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- fix for #5806: GPU hangs and display artifacts on 5.18-rc3 on Intel GM45
- reject DMC with out-of-spec MMIO (Cc: stable)
- correctly mark guilty contexts on GuC reset.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YocqqvG6PbYx3QgJ@jlahtine-mobl.ger.corp.intel.com

Fix for a memory leak in dp_mst, a (userspace) build fix for
DMA_BUF_SET_NAME defines and a directory name generation fix for dmabuf
stats
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520072408.cpjzy2taugagvrh7@houat

Norbert reported that it's possible to race sys_perf_event_open() such
that the looser ends up in another context from the group leader,
triggering many WARNs.

The move_group case checks for races against itself, but the
!move_group case doesn't, seemingly relying on the previous
group_leader->ctx == ctx check. However, that check is racy due to not
holding any locks at that time.

Therefore, re-check the result after acquiring locks and bailing
if they no longer match.

Additionally, clarify the not_move_group case from the
move_group-vs-move_group race.

Fixes: f63a8daa ("perf: Fix event->ctx locking")
Reported-by: Norbert Slusarek <nslusarek@gmx.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull gpio fixes from Bartosz Golaszewski:

 - fix bitops logic in gpio-vf610

 - return an error if the user tries to use inverted polarity in
   gpio-mvebu

* tag 'gpio-fixes-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: mvebu/pwm: Refuse requests with inverted polarity
  gpio: gpio-vf610: do not touch other bits when set the target bit

Pull MMC fix from Ulf Hansson:
 "MMC core:

   - Fix busy polling for MMC_SEND_OP_COND again"

* tag 'mmc-v5.18-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: Fix busy polling for MMC_SEND_OP_COND again

Pull ceph fix from Ilya Dryomov:
 "A fix for a nasty use-after-free, marked for stable"

* tag 'ceph-for-5.18-rc8' of https://github.com/ceph/ceph-client:
  libceph: fix misleading ceph_osdc_cancel_request() comment
  libceph: fix potential use-after-free on linger ping and resends

Pull RISC-V fixes from Palmer Dabbelt:

 - fix the fu540-c000 device tree to avoid a schema check failure on the
   DMA node name

 - fix typo in the PolarFire SOC device tree

* tag 'riscv-for-linus-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: dts: microchip: fix gpio1 reg property typo
  riscv: dts: sifive: fu540-c000: align dma node name with dtschema

Pull arm64 fixes from Will Deacon:
 "Three arm64 fixes for -rc8/final.

  The MTE and stolen time fixes have been doing the rounds for a little
  while, but review and testing feedback was ongoing until earlier this
  week. The kexec fix showed up on Monday and addresses a failure
  observed under Qemu.

  Summary:

   - Add missing write barrier to publish MTE tags before a pte update

   - Fix kexec relocation clobbering its own data structures

   - Fix stolen time crash if a timer IRQ fires during CPU hotplug"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mte: Ensure the cleared tags are visible before setting the PTE
  arm64: kexec: load from kimage prior to clobbering
  arm64: paravirt: Use RCU read locks to guard stolen_time

With shadow paging enabled, the INVPCID instruction results in a call
to kvm_mmu_invpcid_gva.  If INVPCID is executed with CR0.PG=0, the
invlpg callback is not set and the result is a NULL pointer dereference.
Fix it trivially by checking for mmu->invlpg before every call.

There are other possibilities:

- check for CR0.PG, because KVM (like all Intel processors after P5)
  flushes guest TLB on CR0.PG changes so that INVPCID/INVLPG are a
  nop with paging disabled

- check for EFER.LMA, because KVM syncs and flushes when switching
  MMU contexts outside of 64-bit mode

All of these are tricky, go for the simple solution.  This is CVE-2022-1789.
Reported-by: Yongkang Jia <kangel@zju.edu.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

In kvm_hv_flush_tlb(), valid_bank_mask is declared as unsigned long,
but is used as u64, which is wrong for i386, and has been spotted by
LKP after applying "KVM: x86: hyper-v: replace bitmap_weight() with
hweight64()"

https://lore.kernel.org/lkml/20220510154750.212913-12-yury.norov@gmail.com/

But it's wrong even without that patch because now bitmap_weight()
dereferences a word after valid_bank_mask on i386.

>> include/asm-generic/bitops/const_hweight.h:21:76: warning: right shift count >= width of type
+[-Wshift-count-overflow]
      21 | #define __const_hweight64(w) (__const_hweight32(w) + __const_hweight32((w) >> 32))
         |                                                                            ^~
   include/asm-generic/bitops/const_hweight.h:10:16: note: in definition of macro '__const_hweight8'
      10 |          ((!!((w) & (1ULL << 0))) +     \
         |                ^
   include/asm-generic/bitops/const_hweight.h:20:31: note: in expansion of macro '__const_hweight16'
      20 | #define __const_hweight32(w) (__const_hweight16(w) + __const_hweight16((w) >> 16))
         |                               ^~~~~~~~~~~~~~~~~
   include/asm-generic/bitops/const_hweight.h:21:54: note: in expansion of macro '__const_hweight32'
      21 | #define __const_hweight64(w) (__const_hweight32(w) + __const_hweight32((w) >> 32))
         |                                                      ^~~~~~~~~~~~~~~~~
   include/asm-generic/bitops/const_hweight.h:29:49: note: in expansion of macro '__const_hweight64'
      29 | #define hweight64(w) (__builtin_constant_p(w) ? __const_hweight64(w) : __arch_hweight64(w))
         |                                                 ^~~~~~~~~~~~~~~~~
   arch/x86/kvm/hyperv.c:1983:36: note: in expansion of macro 'hweight64'
    1983 |                 if (hc->var_cnt != hweight64(valid_bank_mask))
         |                                    ^~~~~~~~~

CC: Borislav Petkov <bp@alien8.de>
CC: Dave Hansen <dave.hansen@linux.intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: Jim Mattson <jmattson@google.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Sean Christopherson <seanjc@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: Wanpeng Li <wanpengli@tencent.com>
CC: kvm@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: x86@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Message-Id: <20220519171504.1238724-1-yury.norov@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Fix a goof in kvm_prepare_memory_region() where KVM fails to free the
new memslot's dirty bitmap during a CREATE action if
kvm_arch_prepare_memory_region() fails.  The logic is supposed to detect
if the bitmap was allocated and thus needs to be freed, versus if the
bitmap was inherited from the old memslot and thus needs to be kept.  If
there is no old memslot, then obviously the bitmap can't have been
inherited

The bug was exposed by commit 86931ff7 ("KVM: x86/mmu: Do not create
SPTEs for GFNs that exceed host.MAXPHYADDR"), which made it trivally easy
for syzkaller to trigger failure during kvm_arch_prepare_memory_region(),
but the bug can be hit other ways too, e.g. due to -ENOMEM when
allocating x86's memslot metadata.

The backtrace from kmemleak:

  __vmalloc_node_range+0xb40/0xbd0 mm/vmalloc.c:3195
  __vmalloc_node mm/vmalloc.c:3232 [inline]
  __vmalloc+0x49/0x50 mm/vmalloc.c:3246
  __vmalloc_array mm/util.c:671 [inline]
  __vcalloc+0x49/0x70 mm/util.c:694
  kvm_alloc_dirty_bitmap virt/kvm/kvm_main.c:1319
  kvm_prepare_memory_region virt/kvm/kvm_main.c:1551
  kvm_set_memslot+0x1bd/0x690 virt/kvm/kvm_main.c:1782
  __kvm_set_memory_region+0x689/0x750 virt/kvm/kvm_main.c:1949
  kvm_set_memory_region virt/kvm/kvm_main.c:1962
  kvm_vm_ioctl_set_memory_region virt/kvm/kvm_main.c:1974
  kvm_vm_ioctl+0x377/0x13a0 virt/kvm/kvm_main.c:4528
  vfs_ioctl fs/ioctl.c:51
  __do_sys_ioctl fs/ioctl.c:870
  __se_sys_ioctl fs/ioctl.c:856
  __x64_sys_ioctl+0xfc/0x140 fs/ioctl.c:856
  do_syscall_x64 arch/x86/entry/common.c:50
  do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
  entry_SYSCALL_64_after_hwframe+0x44/0xae

And the relevant sequence of KVM events:

  ioctl(3, KVM_CREATE_VM, 0)              = 4
  ioctl(4, KVM_SET_USER_MEMORY_REGION, {slot=0,
                                        flags=KVM_MEM_LOG_DIRTY_PAGES,
                                        guest_phys_addr=0x10000000000000,
                                        memory_size=4096,
                                        userspace_addr=0x20fe8000}
       ) = -1 EINVAL (Invalid argument)

Fixes: 244893fa ("KVM: Dynamically allocate "new" memslots from the get-go")
Cc: stable@vger.kernel.org
Reported-by: syzbot+8606b8a9cc97a63f1c87@syzkaller.appspotmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220518003842.1341782-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The driver doesn't take struct pwm_state::polarity into account when
configuring the hardware, so refuse requests for inverted polarity.

Fixes: 757642f9 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.

Fixes: 659d8a62 ("gpio: vf610: add imx7ulp support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The splat below can be seen when running kvm-unit-test:

     =============================
     WARNING: suspicious RCU usage
     5.18.0-rc7 #5 Tainted: G          IOE
     -----------------------------
     /home/kernel/linux/arch/x86/kvm/../../../virt/kvm/eventfd.c:80 RCU-list traversed in non-reader section!!

     other info that might help us debug this:

     rcu_scheduler_active = 2, debug_locks = 1
     4 locks held by qemu-system-x86/35124:
      #0: ffff9725391d80b8 (&vcpu->mutex){+.+.}-{4:4}, at: kvm_vcpu_ioctl+0x77/0x710 [kvm]
      #1: ffffbd25cfb2a0b8 (&kvm->srcu){....}-{0:0}, at: vcpu_enter_guest+0xdeb/0x1900 [kvm]
      #2: ffffbd25cfb2b920 (&kvm->irq_srcu){....}-{0:0}, at: kvm_hv_notify_acked_sint+0x79/0x1e0 [kvm]
      #3: ffffbd25cfb2b920 (&kvm->irq_srcu){....}-{0:0}, at: irqfd_resampler_ack+0x5/0x110 [kvm]

     stack backtrace:
     CPU: 2 PID: 35124 Comm: qemu-system-x86 Tainted: G          IOE     5.18.0-rc7 #5
     Call Trace:
      <TASK>
      dump_stack_lvl+0x6c/0x9b
      irqfd_resampler_ack+0xfd/0x110 [kvm]
      kvm_notify_acked_gsi+0x32/0x90 [kvm]
      kvm_hv_notify_acked_sint+0xc5/0x1e0 [kvm]
      kvm_hv_set_msr_common+0xec1/0x1160 [kvm]
      kvm_set_msr_common+0x7c3/0xf60 [kvm]
      vmx_set_msr+0x394/0x1240 [kvm_intel]
      kvm_set_msr_ignored_check+0x86/0x200 [kvm]
      kvm_emulate_wrmsr+0x4f/0x1f0 [kvm]
      vmx_handle_exit+0x6fb/0x7e0 [kvm_intel]
      vcpu_enter_guest+0xe5a/0x1900 [kvm]
      kvm_arch_vcpu_ioctl_run+0x16e/0xac0 [kvm]
      kvm_vcpu_ioctl+0x279/0x710 [kvm]
      __x64_sys_ioctl+0x83/0xb0
      do_syscall_64+0x3b/0x90
      entry_SYSCALL_64_after_hwframe+0x44/0xae

resampler-list is protected by irq_srcu (see kvm_irqfd_assign), so fix
the false positive by using list_for_each_entry_srcu().
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1652950153-12489-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Add a test to demonstrate that when the guest programs an event select
it is matched correctly in the pmu event filter and not inadvertently
filtered.  This could happen on AMD if the high nybble[1] in the event
select gets truncated away only leaving the bottom byte[2] left for
matching.

This is a contrived example used for the convenience of demonstrating
this issue, however, this can be applied to event selects 0x28A (OC
Mode Switch) and 0x08A (L1 BTB Correction), where 0x08A could end up
being denied when the event select was only set up to deny 0x28A.

[1] bits 35:32 in the event select register and bits 11:8 in the event
    select.
[2] bits 7:0 in the event select register and bits 7:0 in the event
    select.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Message-Id: <20220517051238.2566934-3-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Add a helper function that creates a pmu event filter given an event
list.  Currently, a pmu event filter can only be created with the same
hard coded event list.  Add a way to create one given a different event
list.

Also, rename make_pmu_event_filter to alloc_pmu_event_filter to clarify
it's purpose given the introduction of create_pmu_event_filter.

No functional changes intended.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Message-Id: <20220517051238.2566934-2-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

When returning from the compare function the u64 is truncated to an
int.  This results in a loss of the high nybble[1] in the event select
and its sign if that nybble is in use.  Switch from using a result that
can end up being truncated to a result that can only be: 1, 0, -1.

[1] bits 35:32 in the event select register and bits 11:8 in the event
    select.

Fixes: 7ff775ac ("KVM: x86/pmu: Use binary search to check filtered events")
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220517051238.2566934-1-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull crypto fix from Herbert Xu:
 "Fix a regression in a recent fix to qcom-rng"

* tag 'v5.18-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: qcom-rng - fix infinite loop on requests not multiple of WORD_SZ

Fix referencing sense data when it is invalid. When the length of the data
segment is 0, there is no valid information in the rsp field, so
ufshpb_rsp_upiu() is returned without additional operation.

Link: https://lore.kernel.org/r/252651381.41652940482659.JavaMail.epsvc@epcpadp4
Fixes: 4b5f4907 ("scsi: ufs: ufshpb: L2P map management for HPB read")
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix reg address typo in the gpio1 stanza.
Signed-off-by: Conor Paxton <conor.paxton@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: 528a5b1f ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Link: https://lore.kernel.org/r/20220517104058.2004734-1-conor.paxton@microchip.comSigned-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Fixes dtbs_check warnings like:

  dma@3000000: $nodename:0: 'dma@3000000' does not match '^dma-controller(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220407193856.18223-1-krzysztof.kozlowski@linaro.org
Fixes: c5ab54e9 ("riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00")
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Pull parisc architecture fixes from Helge Deller:
 "We had two big outstanding issues after v5.18-rc6:

   a) 32-bit kernels on 64-bit machines (e.g. on a C3700 which is able
      to run 32- and 64-bit kernels) failed early in userspace.

   b) 64-bit kernels on PA8800/PA8900 CPUs (e.g. in a C8000) showed
      random userspace segfaults. We assumed that those problems were
      caused by the tmpalias flushes.

  Dave did a lot of testing and reorganization of the current flush code
  and fixed the 32-bit cache flushing. For PA8800/PA8900 CPUs he
  switched the code to flush using the virtual address of user and
  kernel pages instead of using tmpalias flushes. The tmpalias flushes
  don't seem to work reliable on such CPUs.

  We tested the patches on a wide range machines (715/64, B160L, C3000,
  C3700, C8000, rp3440) and they have been in for-next without any
  conflicts.

  Summary:

   - Rewrite the cache flush code for PA8800/PA8900 CPUs to flush using
     the virtual address of user and kernel pages instead of using
     tmpalias flushes. Testing showed, that tmpalias flushes don't work
     reliably on PA8800/PA8900 CPUs

   - Fix flush code to allow 32-bit kernels to run on 64-bit capable
     machines, e.g. a 32-bit kernel on C3700 machines"

* tag 'for-5.18/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix patch code locking and flushing
  parisc: Rewrite cache flush code for PA8800/PA8900
  parisc: Disable debug code regarding cache flushes in handle_nadtlb_fault()

Pull ARM fixes from Russell King:
 "Two further fixes for Spectre-BHB from Ard for Cortex A15 and to use
  the wide branch instruction for Thumb2"

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9197/1: spectre-bhb: fix loop8 sequence for Thumb2
  ARM: 9196/1: spectre-bhb: enable for Cortex-A15

Pull pin control fixes from Linus Walleij:

 - Fix an altmode in the Ocelot driver

 - Fix the IES control pins in the Mediatek MT8365 driver

 - Sunxi (AMLogic) driver:
    - Fix the UART2 function pin assignments
    - Fix the signal name of the PA2 SPI pin

* tag 'pinctrl-v5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: sunxi: f1c100s: Fix signal name comment for PA2 SPI pin
  pinctrl: sunxi: fix f1c100s uart2 function
  pinctrl: mediatek: mt8365: fix IES control pins
  pinctrl: ocelot: Fix for lan966x alt mode

Pull networking fixes from Paolo Abeni:
 "Including fixes from can, xfrm and netfilter subtrees.

  Notably this reverts a recent TCP/DCCP netns-related change to address
  a possible UaF.

  Current release - regressions:

   - tcp: revert "tcp/dccp: get rid of inet_twsk_purge()"

   - xfrm: set dst dev to blackhole_netdev instead of loopback_dev in
     ifdown

  Previous releases - regressions:

   - netfilter: flowtable: fix TCP flow teardown

   - can: revert "can: m_can: pci: use custom bit timings for Elkhart
     Lake"

   - xfrm: check encryption module availability consistency

   - eth: vmxnet3: fix possible use-after-free bugs in
     vmxnet3_rq_alloc_rx_buf()

   - eth: mlx5: initialize flow steering during driver probe

   - eth: ice: fix crash when writing timestamp on RX rings

  Previous releases - always broken:

   - mptcp: fix checksum byte order

   - eth: lan966x: fix assignment of the MAC address

   - eth: mlx5: remove HW-GRO from reported features

   - eth: ftgmac100: disable hardware checksum on AST2600"

* tag 'net-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
  net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
  ptp: ocp: change sysfs attr group handling
  selftests: forwarding: fix missing backslash
  netfilter: nf_tables: disable expression reduction infra
  netfilter: flowtable: move dst_check to packet path
  netfilter: flowtable: fix TCP flow teardown
  net: ftgmac100: Disable hardware checksum on AST2600
  igb: skip phy status check where unavailable
  nfc: pn533: Fix buggy cleanup order
  mptcp: Do TCP fallback on early DSS checksum failure
  mptcp: fix checksum byte order
  net: af_key: check encryption module availability consistency
  net: af_key: add check for pfkey_broadcast in function pfkey_process
  net/mlx5: Drain fw_reset when removing device
  net/mlx5e: CT: Fix setting flow_source for smfs ct tuples
  net/mlx5e: CT: Fix support for GRE tuples
  net/mlx5e: Remove HW-GRO from reported features
  net/mlx5e: Properly block HW GRO when XDP is enabled
  net/mlx5e: Properly block LRO when XDP is enabled
  net/mlx5e: Block rx-gro-hw feature in switchdev mode
  ...

It turned out that polling period for MMC_SEND_OP_COND, that currently is
set to 1ms, still isn't sufficient. In particular a Micron eMMC on a
Beaglebone platform, is reported to sometimes fail to initialize.

Additional test, shows that extending the period to 4ms is working fine, so
let's make that change.
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Fixes: 1760fdb6 (mmc: core: Restore (almost) the busy polling for MMC_SEND_OP_COND")
Fixes: 76bfc7cc ("mmc: core: adjust polling interval for CMD1")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220517101046.27512-1-ulf.hansson@linaro.org

When removing short term pins, I've changed the the batch buffer
pinning for relocation to use __i915_vma_pin, because
i915_gem_object_ggtt_pin_ww was destroying the old vma. This
caused regressions, because the functions are not identical.

Fix the regressions by calling i915_gem_object_ggtt_pin_ww() again
on ggtt-only platforms, but only if the batch can be pinned without
being moved.

Fixes: b5cfe6f7 ("drm/i915: Remove short-term pins from execbuf, v6.")
Cc: Matthew Auld <matthew.auld@intel.com>
Reported-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5806
Link: https://patchwork.freedesktop.org/patch/msgid/20220511115219.46507-1-maarten.lankhorst@linux.intel.com
(cherry picked from commit 451374ee)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:

       br1
     /    \
    /      \
   /        \
 br0.11    wlan0
   |
   br0
 /  |  \
p1  p2  p3

br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.

A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.

When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().

Fixes: f1c2eddf ("bridge: switchdev: Use an helper to clear forward mark")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.chSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In the detach path, the driver calls sysfs_remove_group() for the
groups it believes has been registered.  However, if the group was
never previously registered, then this causes a splat.

Instead, compute the groups that should be registered in advance,
and then call sysfs_create_groups(), which registers them all at once.

Update the error handling appropriately.

Fixes: c205d53c ("ptp: ocp: Add firmware capability bits for feature gating")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220517214600.10606-1-jonathan.lemon@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'amd-drm-fixes-5.18-2022-05-18' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-5.18-2022-05-18:

amdgpu:
- Suspend/resume regression fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518202045.9123-1-alexander.deucher@amd.com

Fix missing backslash, introduced in f62c5acc.  Causes all tests to
not be installed.

Fixes: f62c5acc ("selftests/net/forwarding: add missing tests to Makefile")
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220518151630.2747773-1-troglobit@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Reduce number of hardware offload retries from flowtable datapath
   which might hog system with retries, from Felix Fietkau.

2) Skip neighbour lookup for PPPoE device, fill_forward_path() already
   provides this and set on destination address from fill_forward_path for
   PPPoE device, also from Felix.

4) When combining PPPoE on top of a VLAN device, set info->outdev to the
   PPPoE device so software offload works, from Felix.

5) Fix TCP teardown flowtable state, races with conntrack gc might result
   in resetting the state to ESTABLISHED and the time to one day. Joint
   work with Oz Shlomo and Sven Auhagen.

6) Call dst_check() from flowtable datapath to check if dst is stale
   instead of doing it from garbage collector path.

7) Disable register tracking infrastructure, either user-space or
   kernel need to pre-fetch keys inconditionally, otherwise register
   tracking assumes data is already available in register that might
   not well be there, leading to incorrect reductions.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nf_tables: disable expression reduction infra
  netfilter: flowtable: move dst_check to packet path
  netfilter: flowtable: fix TCP flow teardown
  netfilter: nft_flow_offload: fix offload with pppoe + vlan
  net: fix dev_fill_forward_path with pppoe + bridge
  netfilter: nft_flow_offload: skip dst neigh lookup for ppp devices
  netfilter: flowtable: fix excessive hw offload attempts after failure
====================

Link: https://lore.kernel.org/r/20220518213841.359653-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull block fix from Jens Axboe:
 "Just a small fix for a missing fifo time assigment for the head
  insertion case in mq-deadline"

* tag 'block-5.18-2022-05-18' of git://git.kernel.dk/linux-block:
  block/mq-deadline: Set the fifo_time member also if inserting at head

Pull io_uring fixes from Jens Axboe:
 "Two small changes fixing issues from the 5.18 merge window:

   - Fix wrong ordering of a tracepoint (Dylan)

   - Fix MSG_RING on IOPOLL rings (me)"

* tag 'io_uring-5.18-2022-05-18' of git://git.kernel.dk/linux-block:
  io_uring: don't attempt to IOPOLL for MSG_RING requests
  io_uring: fix ordering of args in io_uring_queue_async_work

Pull audit fix from Paul Moore:
 "A single audit patch to fix a problem where a task's audit_context was
  not being properly reset with io_uring"

* tag 'audit-pr-20220518' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit,io_uring,io-wq: call __audit_uring_exit for dummy contexts

Pull selinux fix from Paul Moore:
 "A single SELinux patch to fix an error path that was doing the wrong
  thing with respect to freeing memory"

* tag 'selinux-pr-20220518' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: fix bad cleanup on error in hashtab_duplicate()