- 25 Oct, 2021 40 commits
-
-
David Awogbemila authored
This enables the driver to receive RX packets spread across multiple buffers: For a given multi-fragment packet the "packet continuation" bit is set on all descriptors except the last one. These descriptors' payloads are combined into a single SKB before the SKB is handed to the networking stack. This change adds a "packet buffer size" notion for RX queues. The CreateRxQueue AdminQueue command sent to the device now includes the packet_buffer_size. We opt for a packet_buffer_size of PAGE_SIZE / 2 to give the driver the opportunity to flip pages where we can instead of copying. Signed-off-by:
David Awogbemila <awogbemila@google.com> Signed-off-by:
Jeroen de Borst <jeroendb@google.com> Reviewed-by:
Catherine Sullivan <csully@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Awogbemila authored
This refactor moves the skb_head and skb_tail fields into a new gve_rx_ctx struct. This new struct will contain information about the current packet being processed. This is in preparation for multi-descriptor RX packets. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== selftests: mlxsw: Various updates This patchset contains various updates to mlxsw selftests. Patch #1 replaces open-coded compatibility checks with dedicated helpers. These helpers are used to skip tests when run on incompatible machines. Patch #2 avoids spurious failures in some tests by using permanent neighbours instead of reachable ones. Patch #3 reduces the run time of a test by not iterating over all the available trap policers. ==================== Signed-off-by: -
Ido Schimmel authored
Instead of iterating over all the available trap policers, only perform the tests with three policers: The first, the last and the one in the middle of the range. On a Spectrum-3 system, this reduces the run time from almost an hour to a few minutes. Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
-
Ido Schimmel authored
The nexthop objects tests configure dummy reachable neighbours so that the nexthops will have a MAC address and be programmed to the device. Since these are dummy reachable neighbours, they can be transitioned by the kernel to a failed state if they are around for too long. This can happen, for example, if the "TIMEOUT" variable is configured with a too high value. Make the tests more robust by configuring the neighbours as permanent, so that the tests do not depend on the configured timeout value. Signed-off-by:
-
Petr Machata authored
A number of mlxsw-specific selftests currently detect whether they are run on a compatible machine, and bail out silently when not. These tests are however done in a somewhat impenetrable manner by directly comparing PCI IDs against a blacklist or a whitelist, and bailing out silently if the machine is not compatible. Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying the supported machines in a human-readable manner. If the current machine is incompatible, the helper emits a SKIP message and returns an error code, based on which the caller can gracefully bail out in a suitable way. This allows a more readable conditions such as: mlxsw_only_on_spectrum 2+ || return Convert all existing open-coded guards to the new helper. Also add two new guards to do_mark_test() and do_drop_test(), which are supported only on Spectrum-2+, but the corresponding check was not there. Signed-off-by:
-
David S. Miller authored
Luo Jie says: ==================== net: phy: Add qca8081 ethernet phy driver This patch series add the qca8081 ethernet phy driver support, which improve the wol feature, leverage at803x phy driver and add the fast retrain, master/slave seed and CDT feature. Changes in v7: * update Reviewed-by tags. Changes in v6: * add Reviewed-by tags on the applicable patches. Changes in v5: * rebase the patches on net-next/master. Changes in v4: * handle other interrupts in set_wol. * add genphy_c45_fast_retrain. Changes in v3: * correct a typo "excpet". * remove the suffix "PHY" from phy name. Changes in v2: * add definitions of fast retrain related registers in mdio.h. * break up the patch into small patches. * improve the at803x legacy code. Changes in v1: * merge qca8081 phy driver into at803x. * add cdt feature. * leverage at803x phy driver helpers. ==================== Signed-off-by: -
Luo Jie authored
To perform CDT of qca8081 phy: 1. disable hibernation. 2. force phy working in MDI mode. 3. force phy working in 1000BASE-T mode. 4. configure the related thresholds. Signed-off-by:
Luo Jie <luoj@codeaurora.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Luo Jie authored
1. The master/slave seed needs to be updated when the link can't be created. 2. The case where two qca8081 PHYs are connected each other and master/slave seed is generated as the same value also needs to be considered, so adding this code change into read_status instead of link_change_notify. Signed-off-by:
-
Luo Jie authored
qca8081 phy is a single port phy, configure phy the lower seed value to make it linked as slave mode easier. Signed-off-by:
-
Luo Jie authored
Add the qca8081 phy driver config_init function, which includes: 1. Enable fast restrain. 2. Add 802.3az configurations. 3. Initialize ADC threshold as 100mv. Signed-off-by:
-
Luo Jie authored
Add generic fast retrain auto-negotiation function for C45 PHYs. Signed-off-by:
-
Luo Jie authored
Add the constants for 2.5G fast retrain capability in 10G AN control register, fast retrain status and control register and THP bypass register into mdio.h. Signed-off-by:
-
Luo Jie authored
Reuse at803x phy driver config_aneg excepting adding 2500M auto-negotiation. Signed-off-by:
-
Luo Jie authored
Reuse the at803x phy driver get_features excepting adding 2500M capability. Signed-off-by:
-
Luo Jie authored
1. Separate the function at803x_read_specific_status from the at803x_read_status, since it can be reused by the read_status of qca8081 phy driver excepting adding the 2500M speed. 2. Add the qca8081 read_status function qca808x_read_status. Signed-off-by:
-
Luo Jie authored
qca8081 is a single port ethernet phy chip that supports 10/100/1000/2500 Mbps mode. Add the basic phy driver features, and reuse the at803x phy driver functions. Signed-off-by:
-
Luo Jie authored
Use GENMASK() for the current speed value. Signed-off-by:
-
Luo Jie authored
The wol feature is controlled by the MMD3.8012 bit5, need to set this bit when the wol function is enabled. The reg18 bit0 is for enabling WOL interrupt, when wol occurs, the wol interrupt status reg19 bit0 is set to 1. Call phy_trigger_machine if there are any other interrupt pending in the function set_wol. Signed-off-by:
-
Luo Jie authored
Convert at803x_set_wol to use phy_modify. Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Luo Jie authored
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h. Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: updates for -next This series includes some updates for the HNS3 ethernet driver. for it. off. ==================== Signed-off-by: -
Jiaran Zhang authored
This patch adds himac error recovery module, link_error type and ptp_error type for himac. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Weihang Li authored
This patch adds one ras error of bus related for roce, this error including RRESP/BRESP and read poison error. Signed-off-by:
Weihang Li <liweihang@huawei.com> Signed-off-by:
-
Guangbin Huang authored
Currently, the ethtool advertised link modes of FIBRE port is cleared to zero when autoneg is off, so user can not get the advertised link modes info directly from "ethtool <dev>" command. In order to ameliorate this situation, update data of speeds, fec and pause of advertised link modes when autoneg is off. Signed-off-by:
-
Guangbin Huang authored
The functions of converting speed ability to ethtool link mode just support setting mac->supported currently, to reuse these functions to set ethtool link mode for others(i.e. advertising), delete the argument mac and add argument link_mode. Signed-off-by:
-
Guangbin Huang authored
The mac statistics add pause/pfc durations in device version V3, we can get total active cycle of pause/pfc from these durations. As driver gets register number from firmware to calculate desc number to query mac statistics, it needs to set mac statistics extended enable bit in firmware command 0x701A to tell firmware that driver supports extended mac statistics, otherwise firmware only returns register number of version V1. As pause/pfc durations are not supported by hardware of old version, they should not been shown in command "ethtool -S ethX" in this case, so add checking max register number of each mac statistic in their version. If the max register number of one mac statistic is greater than register number got from firmware, it means hardware does not support this mac statistic, so ignore this statistic when get string and data of mac statistic. Signed-off-by:
-
Guangbin Huang authored
Currently, driver queries number of mac statistics before querying mac statistics. As the number of mac statistics is a fixed value in firmware, it is redundant to query this number everytime before querying mac statistics, it can just be queried once in initialization process and saved in device specifications. Signed-off-by:
-
Guangbin Huang authored
After querying mac statistics from firmware, driver copies data from descriptors to struct mac_stats of hdev, and the number of copied data is just according to the register number queried from firmware. There is a problem that if the register number queried from firmware is larger than data number of struct mac_stats, it will cause a copy overflow. So if the firmware adds more mac statistics in later version, it is not compatible with driver of old version. To fix this problem, the number of copied data needs to be used the minimum value between the register number queried from firmware and data number of struct mac_stats. The first descriptor has three data and there is one reserved, to optimize the copy process, add this reserverd data to struct mac_stats. Signed-off-by:
-
Huazhong Tan authored
Since user may need to check the current configuration of the interrupt coalesce, so add debugfs support for query this info. Create a single file "coalesce_info" for it, and query it by "cat coalesce_info", return the result to userspace. For device whose version is above V3(include V3), the GL's register contains usecs and 1us unit configuration. When get the usecs configuration from this register, it will include the confusing unit configuration, so add a GL mask to get the correct value, and add a QL mask for the frames configuration as well. The display style is below: $ cat coalesce_info tx interrupt coalesce info: VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT... 0 IN_PROG 4 EQE ON_TOP 0... 1 START 3 EQE LEFT 1... rx interrupt coalesce info: VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT... 0 IN_PROG 3 EQE LEFT 1... 1 IN_PROG 0 EQE ON_TOP 0... Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: updates 2021-10-25 please apply the following patch series for qeth to netdev's net-next tree. This brings some minor maintenance improvements, and a bunch of cleanups so that the W=1 build passes without warning. ==================== Signed-off-by: -
Julian Wiedmann authored
qeth_add_hw_header() is missing documentation for some of its parameters, fix that up. Reported-by:
Heiko Carstens <hca@linux.ibm.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Heiko Carstens authored
Fix kernel doc comments and remove incorrect kernel doc indicators. Acked-by:
-
Heiko Carstens authored
Allow the compiler to recognize and check format strings and parameters. As reported with allmodconfig and W=1: drivers/s390/net/qeth_core_main.c: In function ‘qeth_dbf_longtext’: drivers/s390/net/qeth_core_main.c:6190:9: error: function ‘qeth_dbf_longtext’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format] 6190 | vsnprintf(dbf_txt_buf, sizeof(dbf_txt_buf), fmt, args); | ^~~~~~~~~ Acked-by: -
Heiko Carstens authored
Various format strings don't match with types of parameters. Fix all of them. Acked-by:
-
Julian Wiedmann authored
The only actual user of qdio.no_input_queues is qeth_qdio_establish(), and there we already have full awareness of the current Input Queue configuration (1 RX queue, plus potentially 1 TX Completion queue). So avoid this state tracking, and the ambiguity it brings with it. Signed-off-by:
-
Julian Wiedmann authored
For none of the users we are under risk of running in HW IRQ context or or with IRQs disabled. Thus we always end up in consume_skb(). But the two occurences in the RX path should really report the dropped packet to dropmon, so have them use kfree_skb() instead. That's also consistent with what napi_free_frags() does internally. Signed-off-by:
-
Julian Wiedmann authored
qdio.ko no longer needs to care about how the QAOBs are allocated, from its perspective they are merely another parameter to do_QDIO(). So for a start, shift the cache into the only qdio driver that uses QAOBs (ie. qeth). Here there's further opportunity to optimize its usage in the future - eg. make it per-{device, TX queue}, or only compile it when the driver is built with CQ/QAOB support. Signed-off-by:Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
With commit 18787eee ("qeth: use ndo_siocdevprivate") this callback is now actually used to handle transport mode-specific _private_ ioctls. We only have such ioctls for L3 devices. So wire up a L3-specific .ndo_siocdevprivate() callback that handles those ioctls, and defers to the core qeth_siocdevprivate() for all other private ioctls. This takes the discipline one step closer to its original purpose of providing an internal extension for the qeth_core_ccwgroup_driver. Signed-off-by:
-
Julian Wiedmann authored
Add the failed MAC address into the trace message. Also fix up one format string to use %x instead of %u for the CARD_DEVID. Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
-
