For TCP flows, inet6_sk(sk)->saddr has the same value
than sk->sk_v6_rcv_saddr.

Using sk->sk_v6_rcv_saddr increases data locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some reason, I forgot to change __tcp_v6_send_check() at
the same time I removed (ip_summed == CHECKSUM_PARTIAL) check
in __tcp_v4_send_check()

Fixes: 98be9b12 ("tcp: remove dead code after CHECKSUM_PARTIAL adoption")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If packet is going to be coalesced, sk_sndbuf/sk_rcvbuf values
are not used. Defer their access to the point we need them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were several cases where validate() would return bogus supported
modes with unusual combinations of interfaces and capabilities. For
example, if state->interface was 10GBASER and the macb had HIGH_SPEED
and PCS but not GIGABIT MODE, then 10/100 modes would be set anyway. In
another case, SGMII could be enabled even if the mac was not a GEM
(despite this being checked for later on in mac_config()). These
inconsistencies make it difficult to refactor this function cleanly.

There is still the open question of what exactly the requirements for
SGMII and 10GBASER are, and what SGMII actually supports. If someone
from Cadence (or anyone else with access to the GEM/MACB datasheet)
could comment on this, it would be greatly appreciated. In particular,
what is supported by Cadence vs. vendor extension/limitation?

To address this, the current logic is split into three parts. First, we
determine what we support, then we eliminate unsupported interfaces, and
finally we set the appropriate link modes. There is still some cruft
related to NA, but this can be removed in a future patch.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Parshuram Thombare <pthombar@cadence.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211112190400.1937855-1-sean.anderson@seco.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf-next 2021-11-15

We've added 72 non-merge commits during the last 13 day(s) which contain
a total of 171 files changed, 2728 insertions(+), 1143 deletions(-).

The main changes are:

1) Add btf_type_tag attributes to bring kernel annotations like __user/__rcu to
   BTF such that BPF verifier will be able to detect misuse, from Yonghong Song.

2) Big batch of libbpf improvements including various fixes, future proofing APIs,
   and adding a unified, OPTS-based bpf_prog_load() low-level API, from Andrii Nakryiko.

3) Add ingress_ifindex to BPF_SK_LOOKUP program type for selectively applying the
   programmable socket lookup logic to packets from a given netdev, from Mark Pashmfouroush.

4) Remove the 128M upper JIT limit for BPF programs on arm64 and add selftest to
   ensure exception handling still works, from Russell King and Alan Maguire.

5) Add a new bpf_find_vma() helper for tracing to map an address to the backing
   file such as shared library, from Song Liu.

6) Batch of various misc fixes to bpftool, fixing a memory leak in BPF program dump,
   updating documentation and bash-completion among others, from Quentin Monnet.

7) Deprecate libbpf bpf_program__get_prog_info_linear() API and migrate its users as
   the API is heavily tailored around perf and is non-generic, from Dave Marchevsky.

8) Enable libbpf's strict mode by default in bpftool and add a --legacy option as an
   opt-out for more relaxed BPF program requirements, from Stanislav Fomichev.

9) Fix bpftool to use libbpf_get_error() to check for errors, from Hengqi Chen.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (72 commits)
  bpftool: Use libbpf_get_error() to check error
  bpftool: Fix mixed indentation in documentation
  bpftool: Update the lists of names for maps and prog-attach types
  bpftool: Fix indent in option lists in the documentation
  bpftool: Remove inclusion of utilities.mak from Makefiles
  bpftool: Fix memory leak in prog_dump()
  selftests/bpf: Fix a tautological-constant-out-of-range-compare compiler warning
  selftests/bpf: Fix an unused-but-set-variable compiler warning
  bpf: Introduce btf_tracing_ids
  bpf: Extend BTF_ID_LIST_GLOBAL with parameter for number of IDs
  bpftool: Enable libbpf's strict mode by default
  docs/bpf: Update documentation for BTF_KIND_TYPE_TAG support
  selftests/bpf: Clarify llvm dependency with btf_tag selftest
  selftests/bpf: Add a C test for btf_type_tag
  selftests/bpf: Rename progs/tag.c to progs/btf_decl_tag.c
  selftests/bpf: Test BTF_KIND_DECL_TAG for deduplication
  selftests/bpf: Add BTF_KIND_TYPE_TAG unit tests
  selftests/bpf: Test libbpf API function btf__add_type_tag()
  bpftool: Support BTF_KIND_TYPE_TAG
  libbpf: Support BTF_KIND_TYPE_TAG
  ...
====================

Link: https://lore.kernel.org/r/20211115162008.25916-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 71812af7, reversing
changes made to cc0be1ad.

Wolfram Sang says:

Please revert. Besides the driver in net, it modifies the I2C core
code. This has not been acked by the I2C maintainer (in this case me).
So, please don't pull this in via the net tree. The question raised here
(extending SMBus calls to 255 byte) is complicated because we need ABI
backwards compatibility.

Link: https://lore.kernel.org/all/YZJ9H4eM%2FM7OXVN0@shikoro/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Russell King says:

====================
introduce generic phylink validation

The various validate method implementations we have in phylink users
have been quite repetitive but also prone to bugs. These patches
introduce a generic implementation which relies solely on the
supported_interfaces bitmap introduced during last cycle, and in the
first patch, a bit array of MAC capabilities.

MAC drivers are free to continue to do their own thing if they have
special requirements - such as mvneta and mvpp2 which do not support
1000base-X without AN enabled. Most implementations currently in the
kernel can be converted to call phylink_generic_validate() directly
from the phylink MAC operations structure once they fill in the
supported_interfaces and mac_capabilities members of phylink_config.

This series introduces the generic implementation, and converts mvneta
and mvpp2 to use it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert mvpp2 to use phylink_generic_validate() for the bulk of its
validate() implementation. This network adapter has a restriction
that for 802.3z links, autonegotiation must be enabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert mvneta to use phylink_generic_validate() for the bulk of its
validate() implementation. This network adapter has a restriction
that for 802.3z links, autonegotiation must be enabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a generic validate() implementation using the supported_interfaces
and a bitmask of MAC pause/speed/duplex capabilities. This allows us
to entirely eliminate many driver private validate() implementations.

We expose the underlying phylink_get_linkmodes() function so that
drivers which have special needs can still benefit from conversion.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

CHECK   drivers/net/wan/fsl_ucc_hdlc.c
drivers/net/wan/fsl_ucc_hdlc.c:309:57: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:309:57:    expected void [noderef] __iomem *
drivers/net/wan/fsl_ucc_hdlc.c:309:57:    got restricted __be16 *
drivers/net/wan/fsl_ucc_hdlc.c:311:46: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:311:46:    expected void [noderef] __iomem *
drivers/net/wan/fsl_ucc_hdlc.c:311:46:    got restricted __be32 *
drivers/net/wan/fsl_ucc_hdlc.c:320:57: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:320:57:    expected void [noderef] __iomem *
drivers/net/wan/fsl_ucc_hdlc.c:320:57:    got restricted __be16 *
drivers/net/wan/fsl_ucc_hdlc.c:322:46: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:322:46:    expected void [noderef] __iomem *
drivers/net/wan/fsl_ucc_hdlc.c:322:46:    got restricted __be32 *
drivers/net/wan/fsl_ucc_hdlc.c:372:29: warning: incorrect type in assignment (different base types)
drivers/net/wan/fsl_ucc_hdlc.c:372:29:    expected unsigned short [usertype]
drivers/net/wan/fsl_ucc_hdlc.c:372:29:    got restricted __be16 [usertype]
drivers/net/wan/fsl_ucc_hdlc.c:379:36: warning: restricted __be16 degrades to integer
drivers/net/wan/fsl_ucc_hdlc.c:402:12: warning: incorrect type in assignment (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:402:12:    expected struct qe_bd [noderef] __iomem *bd
drivers/net/wan/fsl_ucc_hdlc.c:402:12:    got struct qe_bd *curtx_bd
drivers/net/wan/fsl_ucc_hdlc.c:425:20: warning: incorrect type in assignment (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:425:20:    expected struct qe_bd [noderef] __iomem *[assigned] bd
drivers/net/wan/fsl_ucc_hdlc.c:425:20:    got struct qe_bd *tx_bd_base
drivers/net/wan/fsl_ucc_hdlc.c:427:16: error: incompatible types in comparison expression (different address spaces):
drivers/net/wan/fsl_ucc_hdlc.c:427:16:    struct qe_bd [noderef] __iomem *
drivers/net/wan/fsl_ucc_hdlc.c:427:16:    struct qe_bd *
drivers/net/wan/fsl_ucc_hdlc.c:462:33: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:506:41: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:528:33: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:552:38: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:596:67: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:611:41: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:851:38: warning: incorrect type in initializer (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:854:40: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:855:40: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:858:39: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:861:37: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:866:38: warning: incorrect type in initializer (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:868:21: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:870:40: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:871:40: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:873:39: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:993:57: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:995:46: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:1004:57: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:1006:46: warning: incorrect type in argument 2 (different address spaces)
drivers/net/wan/fsl_ucc_hdlc.c:412:35: warning: dereference of noderef expression
drivers/net/wan/fsl_ucc_hdlc.c:412:35: warning: dereference of noderef expression
drivers/net/wan/fsl_ucc_hdlc.c:724:29: warning: dereference of noderef expression
drivers/net/wan/fsl_ucc_hdlc.c:815:21: warning: dereference of noderef expression
drivers/net/wan/fsl_ucc_hdlc.c:1021:29: warning: dereference of noderef expression

Most of the warnings are due to DMA memory being incorrectly handled as IO memory.
Fix it by doing direct read/write and doing proper dma_rmb() / dma_wmb().

Other problems are type mismatches or lack of use of IO accessors.

Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lkml.org/lkml/2021/11/12/647Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARRAY_SIZE defined in <linux/kernel.h> is safer than self-defined
macros to get size of an array such as ARRAY_LEN used here. Because
ARRAY_SIZE uses __must_be_array(arr) to ensure arr is really an array.
Reported-by: Alejandro Colomar <colomar.6.4.3@gmail.com>
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On low-effciency embedded platforms, transmission performance is poor
due to on Bulk-out with single packet.
Adding TSO feature improves the transmission performance and reduces
the number of interrupt caused by Bulk-out complete.

Reference to module, net: usb: aqc111.
Signed-off-by: Jacky Chou <jackychou@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matt Johnston says:

====================
MCTP I2C driver

This patch series adds a netdev driver providing MCTP transport over
I2C.

It applies against net-next using recent MCTP changes there, though also
has I2C core changes for review. I'll leave it to maintainers where it
should be applied - please let me know if it needs to be submitted
differently.

The I2C patches were previously sent as RFC though the only feedback
there was an ack to 255 bytes for aspeed.

The dt-bindings patch went through review on the list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Provides MCTP network transport over an I2C bus, as specified in
DMTF DSP0237. All messages between nodes are sent as SMBus Block Writes.

Each I2C bus to be used for MCTP is flagged in devicetree by a
'mctp-controller' property on the bus node. Each flagged bus gets a
mctpi2cX net device created based on the bus number. A
'mctp-i2c-controller' I2C client needs to be added under the adapter. In
an I2C mux situation the mctp-i2c-controller node must be attached only
to the root I2C bus. The I2C client will handle incoming I2C slave block
write data for subordinate busses as well as its own bus.

In configurations without devicetree a driver instance can be attached
to a bus using the I2C slave new_device mechanism.

The MCTP core will hold/release the MCTP I2C device while responses
are pending (a 6 second timeout or once a socket is closed, response
received etc). While held the MCTP I2C driver will lock the I2C bus so
that the correct I2C mux remains selected while responses are received.

(Ideally we would just lock the mux to keep the current bus selected for
the response rather than a full I2C bus lock, but that isn't exposed in
the I2C mux API)

This driver requires I2C adapters that allow 255 byte transfers
(SMBus 3.0) as the specification requires a minimum MTU of 68 bytes.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Used to define a local endpoint to communicate with MCTP peripherals
attached to an I2C bus. This I2C endpoint can communicate with remote
MCTP devices on the I2C bus.

In the example I2C topology below (matching the second yaml example) we
have MCTP devices on busses i2c1 and i2c6. MCTP-supporting busses are
indicated by the 'mctp-controller' DT property on an I2C bus node.

A mctp-i2c-controller I2C client DT node is placed at the top of the
mux topology, since only the root I2C adapter will support I2C slave
functionality.
                                               .-------.
                                               |eeprom |
    .------------.     .------.               /'-------'
    | adapter    |     | mux  --@0,i2c5------'
    | i2c1       ----.*|      --@1,i2c6--.--.
    |............|    \'------'           \  \  .........
    | mctp-i2c-  |     \                   \  \ .mctpB  .
    | controller |      \                   \  '.0x30   .
    |            |       \  .........        \  '.......'
    | 0x50       |        \ .mctpA  .         \ .........
    '------------'         '.0x1d   .          '.mctpC  .
                            '.......'          '.0x31   .
                                                '.......'
(mctpX boxes above are remote MCTP devices not included in the DT at
present, they can be hotplugged/probed at runtime. A DT binding for
specific fixed MCTP devices could be added later if required)
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

255 byte support has been tested on a npcm750 board
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

255 byte transfers have been tested on an AST2500 board
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I2C_SMBUS is limited to 32 bytes due to compatibility with the
32 byte i2c_smbus_data.block

I2C_RDWR allows larger transfers if sufficient sized buffers are passed.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMBus 3.0 increased the maximum block transfer size from 32 bytes to
255 bytes. We increase the size of struct i2c_smbus_data's block[]
member.

i2c_smbus_xfer() and i2c_smbus_xfer_emulated() now support 255 byte
block operations, other block functions remain limited to 32 bytes for
compatibility with existing callers.

We allow adapters to indicate support for the larger size with
I2C_FUNC_SMBUS_V3_BLOCK. Most emulated drivers should be able to use 255
byte blocks by replacing I2C_SMBUS_BLOCK_MAX with I2C_SMBUS_V3_BLOCK_MAX
though some will have hardware limitations that need testing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'inuse' bitmap is local to this function. So we can use the
non-atomic '__set_bit()' to save a few cycles.

While at it, also remove some useless {}.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed comments to match description with variable names and
refactored code to match the convention as per [1].

To match the convention mapping is done as follows:
State 3 - LOST_IN_BURST_PERIOD
State 4 - LOST_IN_GAP_PERIOD

[1] S. Salsano, F. Ludovici, A. Ordine, "Definition of a general
and intuitive loss model for packet networks and its implementation
in the Netem module in the Linux kernel"

Fixes: a6e2fe17 ("sch_netem: replace magic numbers with enumerate")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vsc73xx_remove() returns zero unconditionally and no caller checks the
returned value. So convert the function to return no value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous stmmac_xdp_set_prog() implementation uses stmmac_release()
and stmmac_open() which tear down the PHY device and causes undesirable
autonegotiation which causes a delay whenever AFXDP ZC is setup.

This patch introduces two new functions that just sufficiently tear
down DMA descriptors, buffer, NAPI process, and IRQs and reestablish
them accordingly in both stmmac_xdp_release() and stammac_xdp_open().

As the results of this enhancement, we get rid of transient state
introduced by the link auto-negotiation:

$ ./xdpsock -i eth0 -t -z

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 634444         634560

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 632330         1267072

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 632438         1899584

 sock0@eth0:0 txonly xdp-drv
                   pps            pkts           1.00
rx                 0              0
tx                 632502         2532160
Reported-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, LIBBPF_STRICT_ALL mode is enabled by default for
bpftool which means on error cases, some libbpf APIs would
return NULL pointers. This makes IS_ERR check failed to detect
such cases and result in segfault error. Use libbpf_get_error()
instead like we do in libbpf itself.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211115012436.3143318-1-hengqi.chen@gmail.com

Quentin Monnet says:

====================

This set contains several independent minor fixes for bpftool, its
Makefile, and its documentation. Please refer to individual commits for
details.
====================
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>

Some paragraphs in bpftool's documentation have a mix of tabs and spaces
for indentation. Let's make it consistent.

This patch brings no change to the text content.
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211110114632.24537-7-quentin@isovalent.com

To support the different BPF map or attach types, bpftool must remain
up-to-date with the types supported by the kernel. Let's update the
lists, by adding the missing Bloom filter map type and the perf_event
attach type.

Both missing items were found with test_bpftool_synctypes.py.
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211110114632.24537-6-quentin@isovalent.com

Mixed indentation levels in the lists of options in bpftool's
documentation produces some unexpected results. For the "bpftool" man
page, it prints a warning:

    $ make -C bpftool.8
      GEN     bpftool.8
    <stdin>:26: (ERROR/3) Unexpected indentation.

For other pages, there is no warning, but it results in a line break
appearing in the option lists in the generated man pages.

RST paragraphs should have a uniform indentation level. Let's fix it.

Fixes: c07ba629 ("tools: bpftool: Update and synchronise option list in doc and help msg")
Fixes: 8cc8c635 ("tools: bpftool: Document and add bash completion for -L, -B options")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211110114632.24537-5-quentin@isovalent.com

Bpftool's Makefile, and the Makefile for its documentation, both include
scripts/utilities.mak, but they use none of the items defined in this
file. Remove the includes.

Fixes: 71bb428f ("tools: bpf: add bpftool")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211110114632.24537-3-quentin@isovalent.com

Following the extraction of prog_dump() from do_dump(), the struct btf
allocated in prog_dump() is no longer freed on error; the struct
bpf_prog_linfo is not freed at all. Make sure we release them before
exiting the function.

Fixes: ec202509 ("bpftool: Match several programs with same tag")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211110114632.24537-2-quentin@isovalent.com

This statement is repeated with the initialization statement
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

there is a same action when the variable is initialized
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The assignment in the if statement will be overwritten by the
following statement
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using clang to build selftests with LLVM=1 in make commandline,
I hit the following compiler warning:

  benchs/bench_bloom_filter_map.c:84:46: warning: result of comparison of constant 256
    with expression of type '__u8' (aka 'unsigned char') is always false
    [-Wtautological-constant-out-of-range-compare]
                if (args.value_size < 2 || args.value_size > 256) {
                                           ~~~~~~~~~~~~~~~ ^ ~~~

The reason is arg.vaue_size has type __u8, so comparison "args.value_size > 256"
is always false.

This patch fixed the issue by doing proper comparison before assigning the
value to args.value_size. The patch also fixed the same issue in two
other places.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211112204838.3579953-1-yhs@fb.com

When using clang to build selftests with LLVM=1 in make commandline,
I hit the following compiler warning:
  xdpxceiver.c:747:6: warning: variable 'total' set but not used [-Wunused-but-set-variable]
          u32 total = 0;
              ^

This patch fixed the issue by removing that declaration and its
assocatied unused operation.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211112204833.3579457-1-yhs@fb.com

Pull crypto fix from Herbert Xu:
 "This fixes a boot crash regression"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: api - Fix boot-up crash when crypto manager is disabled

Pull more SCSI updates from James Bottomley:
 "This series is all the stragglers that didn't quite make the first
  merge window pull. It's mostly minor updates and bug fixes of merge
  window code but it also has two driver updates: ufs and qla2xxx"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
  scsi: scsi_debug: Don't call kcalloc() if size arg is zero
  scsi: core: Remove command size deduction from scsi_setup_scsi_cmnd()
  scsi: scsi_ioctl: Validate command size
  scsi: ufs: ufshpb: Properly handle max-single-cmd
  scsi: core: Avoid leaving shost->last_reset with stale value if EH does not run
  scsi: bsg: Fix errno when scsi_bsg_register_queue() fails
  scsi: sr: Remove duplicate assignment
  scsi: ufs: ufs-exynos: Introduce ExynosAuto v9 virtual host
  scsi: ufs: ufs-exynos: Multi-host configuration for ExynosAuto v9
  scsi: ufs: ufs-exynos: Support ExynosAuto v9 UFS
  scsi: ufs: ufs-exynos: Add pre/post_hce_enable drv callbacks
  scsi: ufs: ufs-exynos: Factor out priv data init
  scsi: ufs: ufs-exynos: Add EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR option
  scsi: ufs: ufs-exynos: Support custom version of ufs_hba_variant_ops
  scsi: ufs: ufs-exynos: Add setup_clocks callback
  scsi: ufs: ufs-exynos: Add refclkout_stop control
  scsi: ufs: ufs-exynos: Simplify drv_data retrieval
  scsi: ufs: ufs-exynos: Change pclk available max value
  scsi: ufs: Add quirk to enable host controller without PH configuration
  scsi: ufs: Add quirk to handle broken UIC command
  ...

Merge tag 'pwm/for-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "This set is mostly small fixes and cleanups, so more of a janitorial
  update for this cycle"

* tag 'pwm/for-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: vt8500: Rename pwm_busy_wait() to make it obviously driver-specific
  dt-bindings: pwm: tpu: Add R-Car M3-W+ device tree bindings
  dt-bindings: pwm: tpu: Add R-Car V3U device tree bindings
  pwm: pwm-samsung: Trigger manual update when disabling PWM
  pwm: visconti: Simplify using devm_pwmchip_add()
  pwm: samsung: Describe driver in Kconfig
  pwm: Make it explicit that pwm_apply_state() might sleep
  pwm: Add might_sleep() annotations for !CONFIG_PWM API functions
  pwm: atmel: Drop unused header