- 10 Oct, 2017 16 commits
-
-
Florian Fainelli authored
e1000e_put_txbuf() can be called from normal reclamation path as well as when a DMA mapping failure, so we need to differentiate these two cases when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work() and e1000_remove() are processing TX timestamped SKBs and those should not be accounted as drops either. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Willem de Bruijn authored
Devices that support FLAG2_DMA_BURST have different default values for RDTR and RADV. Apply burst mode default settings only when no explicit value was passed at module load. The RDTR default is zero. If the module is loaded for low latency operation with RxIntDelay=0, do not override this value with a burst default of 32. Move the decision to apply burst values earlier, where explicitly initialized module variables can be distinguished from defaults. Signed-off-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Sasha Neftin authored
Intel
® 100/200 Series Chipset platforms reduced the round-trip latency for the LAN Controller DMA accesses, causing in some high performance cases a buffer overrun while the I219 LAN Connected Device is processing the DMA transactions. I219LM and I219V devices can fall into unrecovered Tx hang under very stressfully UDP traffic and multiple reconnection of Ethernet cable. This Tx hang of the LAN Controller is only recovered if the system is rebooted. Slightly slow down DMA access by reducing the number of outstanding requests. This workaround could have an impact on TCP traffic performance on the platform. Disabling TSO eliminates performance loss for TCP traffic without a noticeable impact on CPU performance. Please, refer to I218/I219 specification update: https://www.intel.com/content/www/us/en/embedded/products/networking/ ethernet-connection-i218-family-documentation.html Signed-off-by:Sasha Neftin <sasha.neftin@intel.com> Reviewed-by:
Dima Ruinskiy <dima.ruinskiy@intel.com> Reviewed-by:
Raanan Avargil <raanan.avargil@intel.com> Tested-by:
-
Benjamin Poirier authored
When e1000e_poll() is not fast enough to keep up with incoming traffic, the adapter (when operating in msix mode) raises the Other interrupt to signal Receiver Overrun. This is a double problem because 1) at the moment e1000_msix_other() assumes that it is only called in case of Link Status Change and 2) if the condition persists, the interrupt is repeatedly raised again in quick succession. Ideally we would configure the Other interrupt to not be raised in case of receiver overrun but this doesn't seem possible on this adapter. Instead, we handle the first part of the problem by reverting to the practice of reading ICR in the other interrupt handler, like before commit 16ecba59 ("e1000e: Do not read ICR in Other interrupt"). Thanks to commit 0a8047ac ("e1000e: Fix msi-x interrupt automask") which cleared IAME from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts anymore. We handle the second part of the problem by not re-enabling the Other interrupt right away when there is overrun. Instead, we wait until traffic subsides, napi polling mode is exited and interrupts are re-enabled. Reported-by:
Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Fixes: 16ecba59 ("e1000e: Do not read ICR in Other interrupt") Signed-off-by:
Benjamin Poirier <bpoirier@suse.com> Tested-by:
-
Benjamin Poirier authored
Lennart reported the following race condition: \ e1000_watchdog_task \ e1000e_has_link \ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link /* link is up */ mac->get_link_status = false; /* interrupt */ \ e1000_msix_other hw->mac.get_link_status = true; link_active = !hw->mac.get_link_status /* link_active is false, wrongly */ This problem arises because the single flag get_link_status is used to signal two different states: link status needs checking and link status is down. Avoid the problem by using the return value of .check_for_link to signal the link status to e1000e_has_link(). Reported-by: -
Benjamin Poirier authored
All the helpers return -E1000_ERR_PHY. Signed-off-by:
-
Benjamin Poirier authored
Reading e1000e_check_for_copper_link() shows that get_link_status is set to false after link has been detected. Therefore, it stays TRUE until then. Signed-off-by:
-
Benjamin Poirier authored
In case of error from e1e_rphy(), the loop will exit early and "success" will be set to true erroneously. Signed-off-by:
-
Bernd Edlinger authored
Signed-off-by:
Bernd Edlinger <bernd.edlinger@hotmail.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Willem de Bruijn authored
Vhost-net has a hard limit on the number of zerocopy skbs in flight. When reached, transmission stalls. Stalls cause latency, as well as head-of-line blocking of other flows that do not use zerocopy. Instead of stalling, revert to copy-based transmission. Tested by sending two udp flows from guest to host, one with payload of VHOST_GOODCOPY_LEN, the other too small for zerocopy (1B). The large flow is redirected to a netem instance with 1MBps rate limit and deep 1000 entry queue. modprobe ifb ip link set dev ifb0 up tc qdisc add dev ifb0 root netem limit 1000 rate 1MBit tc qdisc add dev tap0 ingress tc filter add dev tap0 parent ffff: protocol ip \ u32 match ip dport 8000 0xffff \ action mirred egress redirect dev ifb0 Before the delay, both flows process around 80K pps. With the delay, before this patch, both process around 400. After this patch, the large flow is still rate limited, while the small reverts to its original rate. See also discussion in the first link, below. Without rate limiting, {1, 10, 100}x TCP_STREAM tests continued to send at 100% zerocopy. The limit in vhost_exceeds_maxpend must be carefully chosen. With vq->num >> 1, the flows remain correlated. This value happens to correspond to VHOST_MAX_PENDING for vq->num == 256. Allow smaller fractions and ensure correctness also for much smaller values of vq->num, by testing the min() of both explicitly. See also the discussion in the second link below. Changes v1 -> v2 - replaced min with typed min_t - avoid unnecessary whitespace change Link:http://lkml.kernel.org/r/CAF=yD-+Wk9sc9dXMUq1+x_hh=3ThTXa6BnZkygP3tgVpjbp93g@mail.gmail.com Link:http://lkml.kernel.org/r/20170819064129.27272-1-den@klaipeden.comSigned-off-by: -
William Tu authored
Add erspan netlink interface for OVS. Signed-off-by:
William Tu <u9012063@gmail.com> Cc: Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Eric Biggers authored
Switch the DO_ONCE() macro from the deprecated jump label API to the new one. The new one is more readable, and for DO_ONCE() it also makes the generated code more icache-friendly: now the one-time initialization code is placed out-of-line at the jump target, rather than at the inline fallthrough case. Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
-
Wei Wang authored
This patch replaces rcu_deference() with rcu_dereference_bh() in ipv6_route_seq_next() to avoid the following warning: [ 19.431685] WARNING: suspicious RCU usage [ 19.433451] 4.14.0-rc3-00914-g66f5d6ce #118 Not tainted [ 19.435509] ----------------------------- [ 19.437267] net/ipv6/ip6_fib.c:2259 suspicious rcu_dereference_check() usage! [ 19.440790] [ 19.440790] other info that might help us debug this: [ 19.440790] [ 19.444734] [ 19.444734] rcu_scheduler_active = 2, debug_locks = 1 [ 19.447757] 2 locks held by odhcpd/3720: [ 19.449480] #0: (&p->lock){+.+.}, at: [<ffffffffb1231f7d>] seq_read+0x3c/0x333 [ 19.452720] #1: (rcu_read_lock_bh){....}, at: [<ffffffffb1d2b984>] ipv6_route_seq_start+0x5/0xfd [ 19.456323] [ 19.456323] stack backtrace: [ 19.458812] CPU: 0 PID: 3720 Comm: odhcpd Not tainted 4.14.0-rc3-00914-g66f5d6ce #118 [ 19.462042] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 [ 19.465414] Call Trace: [ 19.466788] dump_stack+0x86/0xc0 [ 19.468358] lockdep_rcu_suspicious+0xea/0xf3 [ 19.470183] ipv6_route_seq_next+0x71/0x164 [ 19.471963] seq_read+0x244/0x333 [ 19.473522] proc_reg_read+0x48/0x67 [ 19.475152] ? proc_reg_write+0x67/0x67 [ 19.476862] __vfs_read+0x26/0x10b [ 19.478463] ? __might_fault+0x37/0x84 [ 19.480148] vfs_read+0xba/0x146 [ 19.481690] SyS_read+0x51/0x8e [ 19.483197] do_int80_syscall_32+0x66/0x15a [ 19.484969] entry_INT80_compat+0x32/0x50 [ 19.486707] RIP: 0023:0xf7f0be8e [ 19.488244] RSP: 002b:00000000ffa75d04 EFLAGS: 00000246 ORIG_RAX: 0000000000000003 [ 19.491431] RAX: ffffffffffffffda RBX: 0000000000000009 RCX: 0000000008056068 [ 19.493886] RDX: 0000000000001000 RSI: 0000000008056008 RDI: 0000000000001000 [ 19.496331] RBP: 00000000000001ff R08: 0000000000000000 R09: 0000000000000000 [ 19.498768] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 [ 19.501217] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Fixes: 66f5d6ce ("ipv6: replace rwlock with rcu and spinlock in fib6_table") Reported-by:
Xiaolong Ye <xiaolong.ye@intel.com> Signed-off-by:
Wei Wang <weiwan@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Linus Torvalds authored
Merge powerpc transactional memory fixes from Michael Ellerman: "I figured I'd still send you the commits using a bundle to make sure it works in case I need to do it again in future" This fixes transactional memory state restore for powerpc. * bundle'd patches from Michael Ellerman: powerpc/tm: Fix illegal TM state in signal handler powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2017-10-09 This series contains updates to i40e and i40evf only. Jake fixes missed flag conversion from u64 to u32. Fixes a deafult ITR value issue where the driver defaults to an ITR value of half the expected value (in terms of minimum microseconds between interrupts). So fix this by changing the default values to be calculated using the ITR_REG_TO_USEC() macro which indicates that we are converting from the register units into microseconds. Updates the drivers to bump the tail in increments of 8 and double the number of descriptors we will bundle into one tail bump when receiving. With the recent kernel support for enabling XPS and QoS at the same time, we no longer need to worry about the number of traffic classes when enabling XPS. Lihong converts the use of hash_for_each() to hash_for_each_safe() to safely remove a hash entry. Adds a check for the return value for find_first_bit() in the case that it returns the size passed to search. Alan fixes a bug in which filters are erroneously removed if they are removed and then added again. So make sure that when adding a filter, if we find it already existed in our list, make sure it is not marked to be removed. Jayaprakash adds the retrying of PHY reads when the I2C is busy for a maximum period of 500ms. Rami fixes code comment typo. Stefano Brivio simplifies the code by removing the use of a local return code variable and simply return the results of the read function. ==================== Signed-off-by:
-
- 09 Oct, 2017 24 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2017-10-09 This series contains updates to ixgbe only. Emil fixes an issue where the semaphore bits could be stuck after a reset or a crash, by adding the clearing of software resource bits in the software/firmware synchronization register. Added error checks when we attempt to identify and initialize the PHY to prevent a crash. Fixed a few issues in the logic of ixgbe_clean_test_rings() which was exposed by a previous commit that was causing a crash in ethtool diagnostics. Bhumika Goyal fixes a couple of instances which were overlooked when we made ixgbe_mac_operations constant. Shannon Nelson fixes an issue to restore normal operations after the last MACVLAN offload is removed, otherwise we get stuck in a single queue operations. The infamous Jesper Dangaard Brouer adds a counter which counts the number of times the recycle fails and the real page allocator is invoked. Alex updates the adaptive ITR algorithm to better support the needs of the network. This attempt to make it so that our ITR algorithm will try to prevent either starving a socket buffer for memory in the case of transmit, or overrunning an receive socket buffer on receive. We should function better with new features like XDP which can handle small packets at high rates without needing to lock us into NAPI polling mode. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix object leak on IPSEC offload failure, from Steffen Klassert. 2) Fix range checks in ipset address range addition operations, from Jozsef Kadlecsik. 3) Fix pernet ops unregistration order in ipset, from Florian Westphal. 4) Add missing netlink attribute policy for nl80211 packet pattern attrs, from Peng Xu. 5) Fix PPP device destruction race, from Guillaume Nault. 6) Write marks get lost when BPF verifier processes R1=R2 register assignments, causing incorrect liveness information and less state pruning. Fix from Alexei Starovoitov. 7) Fix blockhole routes so that they are marked dead and therefore not cached in sockets, otherwise IPSEC stops working. From Steffen Klassert. 8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits) cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan net: thunderx: mark expected switch fall-throughs in nicvf_main() udp: fix bcast packet reception netlink: do not set cb_running if dump's start() errs ipv4: Fix traffic triggered IPsec connections. ipv6: Fix traffic triggered IPsec connections. ixgbe: incorrect XDP ring accounting in ethtool tx_frame param net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag Revert commit 1a8b6d76 ("net:add one common config...") ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register ixgbe: Return error when getting PHY address if PHY access is not supported netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1' netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook tipc: Unclone message at secondary destination lookup tipc: correct initialization of skb list gso: fix payload length when gso_size is zero mlxsw: spectrum_router: Avoid expensive lookup during route removal bpf: fix liveness marking doc: Fix typo "8023.ad" in bonding documentation ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real ... -
Aleksander Morgado authored
The u-blox TOBY-L2 is a LTE Cat 4 module with HSPA+ and 2G fallback. This module allows switching to different USB profiles with the 'AT+UUSBCONF' command, and provides a ECM network interface when the 'AT+UUSBCONF=2' profile is selected. The u-blox SARA-U2 is a HSPA module with 2G fallback. The default USB configuration includes a ECM network interface. Both these modules are controlled via AT commands through one of the TTYs exposed. Connecting these modules may be done just by activating the desired PDP context with 'AT+CGACT=1,<cid>' and then running DHCP on the ECM interface. Signed-off-by:
Aleksander Morgado <aleksander@aleksander.es> Signed-off-by:
-
Stefano Brivio authored
Fixes: 09f79fd4 ("i40e: avoid NVM acquire deadlock during NVM update") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Rami Rosen authored
This patch fixes a typo in i40e_vsi_alloc_arrays() documentation. The first parameter name should be "vsi" instead of "type". Signed-off-by:
Rami Rosen <rami.rosen@intel.com> Tested-by:
-
Lihong Yang authored
The computed result of I40E_MAX_VSI_QP * I40E_VIRTCHNL_SUPPORTED_QTYPES is used more than three times in function i40e_config_irq_link_list. Simply declare a local variable to store it to improve readability. Signed-off-by:
Lihong Yang <lihong.yang@intel.com> Tested-by:
-
Jayaprakash Shanmugam authored
- When the I2C is busy, the PHY reads are delayed. The firmware will return EGAIN in these cases with an expectation that the SW will trigger the reads again - This patch retries the operation for a maximum period of 500ms Signed-off-by:
Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com> Tested-by:
-
Lihong Yang authored
The find_first_bit function will return the size passed to search if the first set bit is not found. This patch adds the check in case that happens as the return value would be used as the index in an array and that would have caused the out-of-bounds access. Detected by CoverityScan, CID 1295969 Out-of-bounds access Signed-off-by:
-
Jacob Keller authored
Recently, the kernel gained support for enabling XPS and QoS at the same time. Thus, we no longer need to worry about the number of traffic classes when enabling XPS. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Jacob Keller authored
Double the number of descriptors we'll bundle into one tail bump when receiving. Empirical testing has shown that we reduce CPU utilization and don't appear to reduce throughput or packet rate. 32 seems to be the sweet spot, as it's half the default polling budget, so we'd essentially reduce from 4 tail writes when polling down to 2. Increasing this up to 64 appears to have negative impacts as it may become possible that we don't bump the tail each time we get polled, which could cause a long delay between returning descriptors to the hardware. Signed-off-by:
-
Jacob Keller authored
Hardware only fetches descriptors on cachelines of 8, essentially ignoring the lower 3 bits of the tail register. Thus, it is pointless to bump tail by an unaligned access as the hardware will ignore some of the new descriptors we allocated. Thus, it's ideal if we can ensure tail writes are always aligned to 8. At first, it seems like we'd already do this, since we allocate descriptors in batches which are a multiple of 8. Since we'd always increment by a multiple of 8, it seems like the value should always be aligned. However, this ignores allocation failures. If we fail to allocate a buffer, our tail register will become unaligned. Once it has become unaligned it will essentially be stuck unaligned until a buffer allocation happens to fail at the exact amount necessary to re-align it. We can do better, by simply rounding down the number of buffers we're about to allocate (cleaned_count) such that "next_to_clean + cleaned_count" is rounded to the nearest multiple of 8. We do this by calculating how far off that value is and subtracting it from the cleaned_count. This essentially defers allocation of buffers if they're going to be ignored by hardware anyways, and re-aligns our next_to_use and tail values after a failure to allocate a descriptor. This calculation ensures that we always align the tail writes in a way the hardware expects and don't unnecessarily allocate buffers which won't be fetched immediately. Signed-off-by:
-
Jacob Keller authored
The lrxq thresh value tells hardware to immediately interrupt when there are fewer than N*64 packets left in the ring. Counter intuitively, empirical testing has shown that decreasing this value from 2 to 1, and thus changing from an immediate interrupt at fewer than 128 descriptors down to 64 descriptors causes a small increase in the maximum total packets per second we can receive. This increase occurs even when we're polling with interrupts masked, as the hardware must still handle interrupts internally even if we've disabled them in software. Also reduce the value for any VFs we allocate. Signed-off-by:
-
Jacob Keller authored
In the past we changed driver behavior to not clear the PBA when re-enabling interrupts. This change was motivated by the flawed belief that clearing the PBA would cause a lost interrupt if a receive interrupt occurred while interrupts were disabled. According to empirical testing this isn't the case. Additionally, the data sheet specifically says that we should set the CLEARPBA bit when re-enabling interrupts in a polling setup. This reverts commit 40d72a50 ("i40e/i40evf: don't lose interrupts") Signed-off-by:
-
Jacob Keller authored
The ITR register expects to be programmed in units of 2 microseconds. Because of this, all of the drivers I40E_ITR_* constants are in terms of this 2 microsecond register. Unfortunately, the rx_itr_default value is expected to be programmed in microseconds. Effectively the driver defaults to an ITR value of half the expected value (in terms of minimum microseconds between interrupts). Fix this by changing the default values to be calculated using ITR_REG_TO_USEC macro which indicates that we're converting from the register units into microseconds. Signed-off-by:
-
Alan Brady authored
Due to the asynchronous nature in which mac filters are added and deleted, there exists a bug in which filters are erroneously removed if removed then added again quickly. The events are as such: - filter marked for removal - same filter is re-added before watchdog that cleans up filters - we skip re-adding the filter because we have it already in the list - watchdog filter cleanup kicks off and filter is removed So when we were re-adding the same filter, it didn't actually get added because it already existed in the list, but was marked for removal and had yet to actually be removed. This patch fixes the issue by making sure that when adding a filter, if we find it already existing in our list, make sure it is not marked to be removed. Signed-off-by:Alan Brady <alan.brady@intel.com> Tested-by:
-
Lihong Yang authored
This patch replaces hash_for_each function with hash_for_each_safe when calling __i40e_del_filter. The hash_for_each_safe function is the right one to use when iterating over a hash table to safely remove a hash entry. Otherwise, incorrect values may be read from freed memory. Detected by CoverityScan, CID 1402048 Read from pointer after free Signed-off-by:
-
Jacob Keller authored
Since we don't yet have more than 32 flags, we'll use a u32 for both the hw_features and flag field. Should we gain more flags in the future, we may need to convert to a u64 or separate flags out into two fields. This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf: organize and re-number feature flags"), where the feature flag was not converted form u64 to u32. Signed-off-by:Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds authored
Pull NFS client bugfixes from Trond Myklebust: "Hightlights include: stable fixes: - nfs/filelayout: fix oops when freeing filelayout segment - NFS: Fix uninitialized rpc_wait_queue bugfixes: - NFSv4/pnfs: Fix an infinite layoutget loop - nfs: RPC_MAX_AUTH_SIZE is in bytes" * tag 'nfs-for-4.14-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: NFSv4/pnfs: Fix an infinite layoutget loop nfs/filelayout: fix oops when freeing filelayout segment sunrpc: remove redundant initialization of sock NFS: Fix uninitialized rpc_wait_queue NFS: Cleanup error handling in nfs_idmap_request_key() nfs: RPC_MAX_AUTH_SIZE is in bytes
-
David S. Miller authored
Eric Dumazet says: ==================== ipv6: addrlabel: avoid dirtying ip6addrlbl_entry The refcount on ip6addrlbl_entry is only used to make sure ip6addrlbl_entry does not disappear while ip6addrlbl_get() is allocating an skb. We can instead allocate skb first, then use RCU, so that we no longer need to refcount these structures. ==================== Acked-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Eric Dumazet authored
After previous patch ("ipv6: addrlabel: rework ip6addrlbl_get()") we can remove the refcount from struct ip6addrlbl_entry, since it is no longer elevated in p6addrlbl_get() Signed-off-by: -
Eric Dumazet authored
If we allocate skb before the lookup, we can use RCU without the need of ip6addrlbl_hold() This means that the following patch can get rid of refcounting. Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Cc: Sunil Goutham <sgoutham@cavium.com> Cc: Robert Richter <rric@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: netdev@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter/IPVS fixes for net The following patchset contains Netfilter/IPVS fixes for your net tree, they are: 1) Fix packet drops due to incorrect ECN handling in IPVS, from Vadim Fedorenko. 2) Fix splat with mark restoration in xt_socket with non-full-sock, patch from Subash Abhinov Kasiviswanathan. 3) ipset bogusly bails out when adding IPv4 range containing more than 2^31 addresses, from Jozsef Kadlecsik. 4) Incorrect pernet unregistration order in ipset, from Florian Westphal. 5) Races between dump and swap in ipset results in BUG_ON splats, from Ross Lagerwall. 6) Fix chain renames in nf_tables, from JingPiao Chen. 7) Fix race in pernet codepath with ebtables table registration, from Artem Savkov. 8) Memory leak in error path in set name allocation in nf_tables, patch from Arvind Yadav. 9) Don't dump chain counters if they are not available, this fixes a crash when listing the ruleset. 10) Fix out of bound memory read in strlcpy() in x_tables compat code, from Eric Dumazet. 11) Make sure we only process TCP packets in SYNPROXY hooks, patch from Lin Zhang. 12) Cannot load rules incrementally anymore after xt_bpf with pinned objects, added in revision 1. From Shmulik Ladkani. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2017-10-09 This series contains updates to ixgbe and arch/Kconfig. Mark fixes a case where PHY register access is not supported and we were returning a PHY address, when we should have been returning -EOPNOTSUPP. Sabrina Dubroca fixes the use of a logical "and" when it should have been the bitwise "and" operator. Ding Tianhong reverts the commit that added the Kconfig bool option ARCH_WANT_RELAX_ORDER, since there is now a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING that has been added to indicate that Relaxed Ordering Attributes should not be used for Transaction Layer Packets. Then follows up with making the needed changes to ixgbe to use the new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag. John Fastabend fixes an issue in the ring accounting when the transmit ring parameters are changed via ethtool when an XDP program is attached. ==================== Signed-off-by:
-
