- 18 Oct, 2022 5 commits
-
-
Robert Marko authored
Since now we have control over the PMP8074 PMIC providing various system voltages including L11 which provides the SDIO/eMMC I/O voltage set it as the SDHCI VQMMC supply. This allows SDHCI controller to switch to 1.8V I/O mode and support high speed modes like HS200 and HS400. Signed-off-by:
Robert Marko <robimarko@gmail.com> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220818221815.346233-5-robimarko@gmail.com
-
Robert Marko authored
PMP8074 is a companion PMIC to the Qualcomm IPQ8074 series that is controlled via SPMI. Add DTSI for it providing GPIO, regulator, RTC and VADC support. RTC is disabled by default as there is no built-in battery so it will loose time unless board vendor added a battery, so make it optional. Signed-off-by:
-
Robert Marko authored
APCS now has support for providing the APSS clocks as the child device for IPQ8074. So, add the A53 PLL and XO clocks in order to use APCS as the CPU clocksource for APSS scaling. Signed-off-by:
-
Bjorn Andersson authored
-
Robert Marko authored
IPQ8074 has a tsens v2.3.0 peripheral which monitors temperatures around the various subsystems on the die. So lets add the tsens and thermal zone nodes, passive CPU cooling will come in later patches after CPU frequency scaling is supported. Signed-off-by:
-
- 17 Oct, 2022 35 commits
-
-
Dmitry Baryshkov authored
There are minor differeces between msm8996 and msm8996pro in terms of GPU frequencies support. For example msm8996pro supports 652.8 MHz frequency for the Adreno. Reclect these differences in msm8996pro.dtsi. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Dmitry Baryshkov authored
Fix Adreno OPP table according to the msm-3.18. Enable 624 MHz for the speed bin 3 and 560 MHz for bins 2 and 3. Fixes: 69cc3114 ("arm64: dts: Add Adreno GPU definitions") Signed-off-by:
-
Dmitry Baryshkov authored
Add support for msm8996, speed bin 3. It supports full range of frequencies on the power cluster, but is limited to 1.8 GHz on performance cluster. Signed-off-by:
-
Dmitry Baryshkov authored
Adjust MSM8996 cpufreq tables according to tables in msm-3.18. Some of the frequencies are not supported on speed bins other than 0. Also other speed bins support intermediate topmost frequencies, not supported on speed bin 0. Implement all these differencies. Fixes: 90173a95 ("arm64: dts: qcom: msm8996: Add CPU opps") Signed-off-by:
-
Yassine Oudjana authored
The Xiaomi Mi Note 2 has the MSM8996 Pro SoC. Rename the dts to match, include msm8996pro.dtsi, and add the qcom,msm8996pro compatible. To do that, the msm8996.dtsi include in msm8996-xiaomi-common has to be moved to msm8996-xiaomi-gemini, the only device that needs it included after this change. Since MSM8996Pro is largely compatible with MSM8996, keep old compatible too rather than insiting on qcom,msm8996pro only. This allows the code that doesn't yet know about msm8996pro to continue supporting these devices. [DB: Dropped msm-id changes.] Signed-off-by:
Yassine Oudjana <y.oudjana@protonmail.com> [DB: Applied the same change to Xiaomi Mi 5s Plus (natrium).] Signed-off-by:
-
Yassine Oudjana authored
Qualcomm MSM8996 Pro is a variant of MSM8996 with higher frequencies supported both on CPU and GPU. There are other minor hardware differencies in the CPU and GPU regulators and bus fabrics. However this results in significant differences between 8996 and 8996 Pro CPU OPP tables. Judging from msm-3.18 there are only few common frequencies supported by both msm8996 and msm8996pro. Rather than hacking the tables for msm8996, split msm8996pro support into a separate file. Later this would allow having additional customizations for the CBF, CPR, retulators, etc. [DB: dropped all non-CPU-OPP changes] Fixes: 90173a95 ("arm64: dts: qcom: msm8996: Add CPU opps") Signed-off-by:
-
Dmitry Baryshkov authored
Xiaomi Mi 5s Plus (natrium) and Xiaomi Mi Note 2 (scorpio) use MSM8996Pro rather than plain MSM8996. Describe this in the arm/qcom.yaml bindings. Since MSM8996Pro is largely compatible with MSM8996, keep old compatible too rather than insiting on qcom,msm8996pro only. This allows the code that doesn't yet know about msm8996pro to continue supporting these devices. Signed-off-by:
-
Judy Hsiao authored
Include sc7280-herobrine-audio-rt5682.dtsi in herobrine-r1 as it uses rt5682 codec. Signed-off-by:
Judy Hsiao <judyhsiao@chromium.org> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Judy Hsiao authored
Audio dtsi for sc7280 boards that using rt5682 headset codec: 1. Add dt nodes for sound card which use I2S playback and record through rt5682s and I2S playback through max98357a. 2. Enable lpass cpu node and add pin control and dai-links. Signed-off-by:
-
Judy Hsiao authored
1. Add drive strength property for mi2s1 on sc7280 based platforms. 2. Disable the pull-up for mi2s1 lines. Signed-off-by:
-
Robert Marko authored
APCS DTS addition that was merged, was not supposed to get merged as it was part of patch series that was superseded by 2 more patch series that resolved issues with this one and greatly simplified things. Since it already got merged, start by correcting the register space size as APCS will not be providing regmap for PLL and it will conflict with the standalone A53 PLL node. Fixes: 50ed9fff ("arm64: dts: qcom: ipq8074: add APCS node") Signed-off-by:
-
Rajendra Nayak authored
qup-i2c devices on sc7280 are clocked with a fixed clock (19.2 MHz) Though qup-i2c does not support DVFS, it still needs to vote for a performance state on 'CX' to satisfy the 19.2 Mhz clock frequency requirement. Use 'required-opps' to pass this information from device tree, and also add the power-domains property to specify the CX power-domain. Signed-off-by:
Rajendra Nayak <quic_rjendra@quicinc.com> Signed-off-by:
-
Rajendra Nayak authored
USB has a requirement to put a performance state vote on 'cx' while active. Use 'required-opps' to pass this information from device tree, and since all the GDSCs in GCC (including USB) are sub-domains of cx, we also add cx as a power-domain for GCC. Now when any of the consumers of the GDSCs (in this case USB) votes on a perforamance state, genpd framework can identify that the GDSC itself does not support a performance state and it then propogates the vote to the parent, which in this case is cx. This change would also mean that any GDSC in GCC thats left enabled during low power state (perhaps because its marked with a ALWAYS_ON flag) can prevent the system from entering low power since that would prevent cx from transitioning to low power. Ideally any consumers that would need to have their devices (partially) powered to support wakeups should look at making the resp. GDSCs transtion to a Retention (PWRSTS_RET) state instead of leaving them ALWAYS_ON. Signed-off-by:
-
Krishna Kurapati authored
Add SNPS HS Phy tuning parameters for herobrine variant of SC7280 devices. Signed-off-by:
Krishna Kurapati <quic_kriskura@quicinc.com> Acked-by:
-
Krzysztof Kozlowski authored
Fix typo in the codec's pin name to be configured. Mismatched name caused the pin configuration to be ignored. Fixes: be497abe ("arm64: dts: qcom: Add support for Xiaomi Mi Mix2s") Signed-off-by:
Molly Sophia <mollysophia379@gmail.com> Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
-
Krzysztof Kozlowski authored
The pin configuration (done with generic pin controller helpers and as expressed by bindings) requires children nodes with either: 1. "pins" property and the actual configuration, 2. another set of nodes with above point. The qup_i2c12_default pin configuration used second method - with a "pinmux" child. Fixes: d4b34126 ("arm64: dts: qcom: Add support for Samsung Galaxy Book2") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
The pin configuration (done with generic pin controller helpers and as expressed by bindings) requires children nodes with either: 1. "pins" property and the actual configuration, 2. another set of nodes with above point. The qup_i2c12_default pin configuration used second method - with a "pinmux" child. Fixes: 44acee20 ("arm64: dts: qcom: Add Lenovo Yoga C630") Cc: <stable@vger.kernel.org> Signed-off-by:
Steev Klimaszewski <steev@kali.org> Reviewed-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Reviewed-by:
-
Krzysztof Kozlowski authored
Add default GPIO function to SD card detect pins on SM6125 Sony Xperia, as required by bindings: qcom/sm6125-sony-xperia-seine-pdx201.dtb: pinctrl@500000: sdc2-off-state: 'oneOf' conditional failed, one must be fixed: 'pins' is a required property 'function' is a required property 'clk-pins', 'cmd-pins', 'data-pins', 'sd-cd-pins' do not match any of the regexes: 'pinctrl-[0-9]+' Reviewed-by: -
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. qcom/sdm845-lg-judyln.dtb: gpios@c000: 'vol-up-active-pins' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+' Reviewed-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. qcom/sdm632-fairphone-fp3.dtb: pinctrl@1000000: 'cd-off-pins', 'cd-on-pins', 'gpio-key-default-pins', .... do not match any of the regexes: '-state$', 'pinctrl-[0-9]+' Reviewed-by: -
Krzysztof Kozlowski authored
Add default GPIO function to SPI10 and SPI14 chip-select pins on SC7280 IDP, as required by bindings. Reviewed-by:
-
Krzysztof Kozlowski authored
There are 175 GPIOs (gpio0-174). Reviewed-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. I already tried to do this in commit d801357a ("arm64: dts: qcom: sc7280: align TLMM pin configuration with DT schema") and I missed the fact that these nodes were not part of "state" node. Bindings did not catch these errors due to its own issues. Reviewed-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. qcom/sc8280xp-crd.dtb: pinctrl@f100000: kybd-default-state: 'oneOf' conditional failed, one must be fixed: 'pins' is a required property 'function' is a required property 'disable', 'int-n', 'reset' do not match any of the regexes: 'pinctrl-[0-9]+' 'disable', 'int-n', 'reset' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' Reviewed-by: -
Krzysztof Kozlowski authored
The property to disable bias is "bias-disable". Fixes: e76c7e1f ("arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen") Reviewed-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Drop also unneeded split between mux and config. Reviewed-by:
-
Richard Acayan authored
The dt schema for gpi-dma has been updated with a new fallback compatible string. Add the compatible strings to existing device trees. Signed-off-by:
Richard Acayan <mailingradian@gmail.com> Reviewed-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
When BLSPI1 (originally SPI0, later renamed in commit f82c48d4 ("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added, the device node lacked respective pin configuration assignment. Fixes: 5bf63562 ("arm64: dts: ipq6018: Add a few device nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
The node names should be generic according to Devicetree specification, so use "clock-controller" instead of "cc". The bindings so far did not define this name (as child of APR service). Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects DAI node names to be "dai": qcom/qrb5165-rb5.dtb: dais: 'qi2s@16', 'qi2s@20' do not match any of the regexes: '^dai@[0-9]+$', 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects DAI node names to be "dai": qcom/msm8996-mtp.dtb: dais: 'hdmi@1' does not match any of the regexes: '^dai@[0-9]+$', 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects DAI node names to be "dai": qcom/sdm845-xiaomi-beryllium.dtb: dais: 'qi2s@22' does not match any of the regexes: '^dai@[0-9]+$', 'pinctrl-[0-9]+' Signed-off-by:
-
