commit 9b171e0c upstream.

Running AIO is pinning inode in memory using file reference. Once AIO
is completed using aio_complete(), file reference is put and inode can
be freed from memory. So we have to be sure that calling aio_complete()
is the last thing we do with the inode.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fbbf8555 upstream.

This patch adds missing bounds checking for the configfs provided
mapped_lun value during target_fabric_make_mappedlun() setup ahead
of se_lun_acl initialization.

This addresses a potential OOPs when using a mapped_lun value that
exceeds the hardcoded TRANSPORT_MAX_LUNS_PER_TPG-1 value within
se_node_acl->device_list[].
Reported-by: Jan Engelhardt <jengelh@inai.de>
Cc: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fcf29481 upstream.

This patch fixes a bug in core_tpg_check_initiator_node_acl() ->
core_tpg_get_initiator_node_acl() where a dynamically created
se_node_acl generated during session login would be skipped during
subsequent lookup due to the '!acl->dynamic_node_acl' check, causing
a new se_node_acl to be created with a duplicate ->initiatorname.

This would occur when a fabric endpoint was configured with
TFO->tpg_check_demo_mode()=1 + TPF->tpg_check_demo_mode_cache()=1
preventing the release of an existing se_node_acl during se_session
shutdown.

Also, drop the unnecessary usage of core_tpg_get_initiator_node_acl()
within core_dev_init_initiator_node_lun_acl() that originally
required the extra '!acl->dynamic_node_acl' check, and just pass
the configfs provided se_node_acl pointer instead.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7c100936 upstream.

On non-BIOS platforms it is possible that the BIOS data area contains
garbage instead of being zeroed or something equivalent (firmware
people: we are talking of 1.5K here, so please do the sane thing.)

We need on the order of 20-30K of low memory in order to boot, which
may grow up to < 64K in the future.  We probably want to avoid the
lowest of the low memory.  At the same time, it seems extremely
unlikely that a legitimate EBDA would ever reach down to the 128K
(which would require it to be over half a megabyte in size.)  Thus,
pick 128K as the cutoff for "this is insane, ignore."  We may still
end up reserving a bunch of extra memory on the low megabyte, but that
is not really a major issue these days.  In the worst case we lose
512K of RAM.

This code really should be merged with trim_bios_range() in
arch/x86/kernel/setup.c, but that is a bigger patch for a later merge
window.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/n/tip-oebml055yyfm8yxmria09rja@git.kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a2fd6419 upstream.

Both the PowerPC hypervisor and Xen hypervisor can utilize the
hvc driver.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1361825650-14031-3-git-send-email-konrad.wilk@oracle.comSigned-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2482a92e upstream.

The earlyprintk for Xen PV guests utilizes a simple hypercall
(console_io) to provide output to Xen emergency console.

Note that the Xen hypervisor should be booted with 'loglevel=all'
to output said information.
Reported-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1361825650-14031-2-git-send-email-konrad.wilk@oracle.comSigned-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb834c7a upstream.

commit 1de63d60 ("efi: Clear EFI_RUNTIME_SERVICES rather than
EFI_BOOT by "noefi" boot parameter") attempted to make "noefi" true to
its documentation and disable EFI runtime services to prevent the
bricking bug described in commit e0094244 ("samsung-laptop:
Disable on EFI hardware"). However, it's not possible to clear
EFI_RUNTIME_SERVICES from an early param function because
EFI_RUNTIME_SERVICES is set in efi_init() *after* parse_early_param().

This resulted in "noefi" effectively becoming a no-op and no longer
providing users with a way to disable EFI, which is bad for those
users that have buggy machines.
Reported-by: Walt Nelson Jr <walt0924@gmail.com>
Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1361392572-25657-1-git-send-email-matt@console-pimps.orgSigned-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 27cf9298 upstream.

Including " lapic " in the kernel cmdline on an x86-64 kernel
makes it panic while parsing early params -- e.g. with no user
visible output.

Fix this bug by ensuring arg is non-NULL before passing it to
strncmp().
Reported-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1361303227-13174-1-git-send-email-minipli@googlemail.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c189ea6 upstream.

Commit: c1bf08ac "ftrace: Be first to run code modification on modules"

changed ftrace module notifier's priority to INT_MAX in order to
process the ftrace nops before anything else could touch them
(namely kprobes). This was the correct thing to do.

Unfortunately, the ftrace module notifier also contains the ftrace
clean up code. As opposed to the set up code, this code should be
run *after* all the module notifiers have run in case a module is doing
correct clean-up and unregisters its ftrace hooks. Basically, ftrace
needs to do clean up on module removal, as it needs to know about code
being removed so that it doesn't try to modify that code. But after it
removes the module from its records, if a ftrace user tries to remove
a probe, that removal will fail due as the record of that code segment
no longer exists.

Nothing really bad happens if the probe removal is called after ftrace
did the clean up, but the ftrace removal function will return an error.
Correct code (such as kprobes) will produce a WARN_ON() if it fails
to remove the probe. As people get annoyed by frivolous warnings, it's
best to do the ftrace clean up after everything else.

By splitting the ftrace_module_notifier into two notifiers, one that
does the module load setup that is run at high priority, and the other
that is called for module clean up that is run at low priority, the
problem is solved.
Reported-by: Frank Ch. Eigler <fche@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e182bb38 upstream.

When idr_find() was fed a negative ID, it used to look up the ID
ignoring the sign bit before recent ("idr: remove MAX_IDR_MASK and
move left MAX_IDR_* into idr.c") patch. Now a negative ID triggers
a WARN_ON_ONCE().

__lock_timer() feeds timer_id from userland directly to idr_find()
without sanitizing it which can trigger the above malfunctions.  Add a
range check on @timer_id before invoking idr_find() in __lock_timer().

While timer_t is defined as int by all archs at the moment, Andrew
worries that it may be defined as a larger type later on.  Make the
test cover larger integers too so that it at least is guaranteed to
not return the wrong timer.

Note that WARN_ON_ONCE() in idr_find() on id < 0 is transitional
precaution while moving away from ignoring MSB.  Once it's gone we can
remove the guard as long as timer_t isn't larger than int.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20130220232412.GL3570@htj.dyndns.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f528d980 upstream.

When dma_ops are initialized the unity mappings are
created. The init_device_table_dma() function makes sure DMA
from all devices is blocked by default. This opens a short
window in time where DMA to unity mapped regions is blocked
by the IOMMU. Make sure this does not happen by initializing
the device table after dma_ops.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8afd500c upstream.

The last orphan in the dnext list has its dnext set to NULL. Because
of that, ubifs_delete_orphan assumes that it is not on the dnext list
and frees it immediately instead ignoring it as a second delete. The
orphan is later freed again by erase_deleted.

This change adds an explicit flag to ubifs_orphan indicating whether
it is pending delete.
Signed-off-by: Adam Thomas <adamthomas1111@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2928f0d0 upstream.

The last orphan in the cnext list has its cnext set to NULL. Because
of that, ubifs_delete_orphan assumes that it is not on the cnext list
and frees it immediately instead of adding it to the dnext list. The
freed orphan is later modified by write_orph_node.

This can cause various inconsistencies including directory entries
that cannot be removed and this error:

UBIFS error (pid 20685): layout_cnodes: LPT out of space at LEB 14:129009 needing 17, done_ltab 1, done_lsave 1

This is a regression introduced by
"7074e5eb UBIFS: remove invalid reference to list iterator variable".

This change adds an explicit flag to ubifs_orphan indicating whether
it is pending commit.
Signed-off-by: Adam Thomas <adamthomas1111@gmail.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 63a02ce1 upstream.

On unload, b43 produces a lockdep warning that can be summarized in the
following way:

 ======================================================
 [ INFO: possible circular locking dependency detected ]
 3.8.0-wl+ #117 Not tainted
 -------------------------------------------------------
 modprobe/5557 is trying to acquire lock:
  ((&wl->firmware_load)){+.+.+.}, at: [<ffffffff81062160>] flush_work+0x0/0x2a0

 but task is already holding lock:
  (rtnl_mutex){+.+.+.}, at: [<ffffffff813bd7d2>] rtnl_lock+0x12/0x20

 which lock already depends on the new lock.
 [ INFO: possible circular locking dependency detected ]
 ======================================================

The full output is available at http://lkml.indiana.edu/hypermail/linux/kernel/1302.3/00060.html.
To summarize, commit 6b6fa586 added a 'cancel_work_sync(&wl->firmware_load)'
call in the wrong place.

The fix is to move the cancel_work_sync() call to b43_bcma_remove() and
b43_ssb_remove(). Thanks to Johannes Berg and Michael Buesch for help in
diagnosing the log output.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1a947746 upstream.

First of all, that 28 value makes no sense as
HIRD threshold is a 4-bit value, second of all
it's causing issues for OMAP5.

Using 12 because commit cbc725b3 (usb: dwc3:
keep default hird threshold value as 4b1100)
had the intention of setting the maximum allowed
value of 0xc.

Also, original code has been wrong forever, so
this should be backported as far back as
possible.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 915e202a upstream.

When we reach to link trb, we just need to increase free_slot and then
calculate TRB. Return is not correct, as it will cause wrong TRB DMA
address to fetch in case of update transfer.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cdc359dd upstream.

There were still some corner cases where isoc transfer was not able to
restart, specially when missed isoc does not happen , and in fact gadget does
not queue any new request during giveback.

Cleanup function calls giveback first, which provides a way to queue
another request to gadget. But gadget did not had any data. So , it did
not call ep_queue. To twist it further, gadget did not queue till
cleanup for last queued TRB is called. If we ever reach this scenario,
we must call END TRANSFER, so that we receive a new  xfernotready with
information about current microframe number.

Also insure that there is no request submitted to core when issuing END
TRANSFER.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7efea86c upstream.

There are two reasons to generate missed isoc.

1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.

Current code was able to handle first case only.  This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:

a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in  test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.

Current patch's approach is as under:

If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2b758350 upstream.

Synopsys says:
The HIRD Threshold field must be set to ‘0’ when the device core is
operating in super speed mode.

This patch implements above statement.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c3ad83d9 upstream.

Otherwise, ext4 file systems with the quota featured enable will get a
very confusing "No such process" error message if the quota code is
built as a module and the quota_v2 module has not been loaded.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2ce19e72 upstream.

If an SRP target is no longer reachable and srp_reset_host() fails to
reconnect then ib_srp will invoke scsi_remove_host().  That function
will invoke __scsi_remove_device() for each LUN.  And that last
function will change the device state from SDEV_TRANSPORT_OFFLINE into
SDEV_CANCEL.  Certain user space software, e.g. older versions of
multipathd, continue queueing I/O to SCSI devices that are in the
SDEV_CANCEL state.

If these I/O requests are submitted as SG_IO that means that the
REQ_PREEMPT flag will be set and hence that these requests will be
passed to srp_queuecommand().  These requests will time out.  If new
requests are queued fast enough from user space these active requests
will prevent __scsi_remove_device() to finish.

Avoid this by failing I/O requests in the SDEV_CANCEL state if the
transport is offline.  Introduce a new variable to keep track of the
transport state instead of failing requests if (!target->connected ||
target->qp_in_error), so that the SCSI error handler has a chance to
retry commands after a transport layer failure occurred.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c7c4e7ff upstream.

If a SCSI command times out it is passed to the SCSI error
handler. The SCSI error handler will try to abort the commands that
timed out.  If aborting fails, a device reset will be attempted.  If
the device reset also fails a host reset will be attempted.  If the
host reset also fails the whole procedure will be repeated.

srp_abort() and srp_reset_device() fail for a QP in the error state.
srp_reset_host() fails after host removal has started.  Hence if the
SCSI error handler gets invoked after host removal has started and
with the QP in the error state an endless loop will be triggered.

Modify the SCSI error handling functions in ib_srp as follows:
- Abort SCSI commands properly even if the QP is in the error state.
- Make srp_reset_host() reset SCSI requests even after host removal
  has already started or if reconnecting fails.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3780d1f0 upstream.

Do not send a task management function if sending will fail anyway
because either there is no RDMA/RC connection or the QP is in the
error state.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e1b2f13a upstream.

Remove an assignment that incorrectly overwrites the connection state
update by srp_connect_target().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b56ddbe5 upstream.

This expands the regression fix from
d2821599.
The firmware also needs to be loaded when it was already cached.
Signed-off-by: Florian Zeitz <florob@babelmonkeys.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d2821599 upstream.

This patch fix regression in emu1010 firmware loading after
http://git.alsa-project.org/?p=alsa-kprivate.git;a=commitdiff;h=b209c4dfcd960ab176d4746ab7dc442a3edb4575

I just revert small part of this commit. Tested on emu1212m pci.
Signed-off-by: Mihail Zenkov <mihail.zenkov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 30efd8de upstream.

Just as for analog codecs, a jack that isn't suitable for detection
(in this case, NO_PRESENCE was set) should be a phantom Jack
instead of a normal one.

Thanks to Raymond Yau for spotting.

BugLink: https://bugs.launchpad.net/bugs/961286
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=903869Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aacfddfd upstream.

Along with a clean up commit [e9f66d9b: ALSA: pci: clean up using
module_pci_driver()], bt87x driver lost the functionality of load_all
parameter.  This patch does a partial revert of the commit only for
bt87x.c to recover it.
Reported-by: Clemens Ladisch <cladisch@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 09884964 upstream.

The stack vma is designed to grow automatically (marked with VM_GROWSUP
or VM_GROWSDOWN depending on architecture) when an access is made beyond
the existing boundary.  However, particularly if you have not limited
your stack at all ("ulimit -s unlimited"), this can cause the stack to
grow even if the access was really just one past *another* segment.

And that's wrong, especially since we first grow the segment, but then
immediately later enforce the stack guard page on the last page of the
segment.  So _despite_ first growing the stack segment as a result of
the access, the kernel will then make the access cause a SIGSEGV anyway!

So do the same logic as the guard page check does, and consider an
access to within one page of the next segment to be a bad access, rather
than growing the stack to abut the next segment.
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ac8cc241 upstream.

A single U encoder table can match multiple DCB entries, whereas the
reverse is not true and can lead to us not matching a DCB entry at
all, and fail to initialise some encoders.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8e992c8d upstream.

Matches format used by a couple of other vbios tables, useful
to have laying around already calculated.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f3ed1048 upstream.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 99d17cfa upstream.

This patch converts the module to use clk_prepare_enable and
clk_disable_unprepare variants as required by common clock framework.

Without this the system crash during probe function.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 25736e0c upstream.

This patch let glue driver return -EPROBE_DEFER if the transceiver
is not readly, so we can support defer probe on musb to fix the
below error on 3.7-rc5 if transceiver drivers are built as module:

[   19.052490] unable to find transceiver of type USB2 PHY
[   19.072052] HS USB OTG: no transceiver configured
[   19.076995] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -19
[   19.089355] musb-hdrc: probe of musb-hdrc.0.auto rejects match -19
[   19.096771] driver: 'musb-omap2430': driver_bound: bound to device 'musb-omap2430'
[   19.105194] bus: 'platform': really_probe: bound device musb-omap2430 to driver musb-omap2430
[   19.174407] bus: 'platform': add driver twl4030_usb
[   19.179656] bus: 'platform': driver_probe_device: matched device twl4030_usb with driver twl4030_usb
[   19.202270] bus: 'platform': really_probe: probing driver twl4030_usb with device twl4030_usb
[   19.214172] twl4030_usb twl4030_usb: HW_CONDITIONS 0xc0/192; link 3
[   19.239624] musb-omap2430 musb-omap2430: musb core is not yet ready
[   19.246765] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[   19.254516] driver: 'twl4030_usb': driver_bound: bound to device 'twl4030_usb'
[   19.263580] bus: 'platform': really_probe: bound device twl4030_usb to driver twl4030_usb

Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 681d1e87 upstream.

In the fail1~fail5 failure path, pm_runtime_disable() should
be called to avoid 'Unbalanced pm_runtime_enable' error in
next probe() which may be triggered by defer probe or next
'modprobe musb_hdrc'.

Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 18e03310 upstream.

The current entry in unusual_cypress.h for the Super TOP SATA bridge devices
seems to be causing corruption on newer revisions of this device.  This has
been reported in Arch Linux and Fedora.  The original patch was tested on
devices with bcdDevice of 1.60, whereas the newer devices report bcdDevice
as 2.20.  Limit the UNUSUAL_DEV entry to devices less than 2.20.

This fixes https://bugzilla.redhat.com/show_bug.cgi?id=909591

The Arch Forum post on this is here:
	https://bbs.archlinux.org/viewtopic.php?id=152011Reported-by: Carsten S. <carsteniq@yahoo.com>
Tested-by: Carsten S. <carsteniq@yahoo.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cd060956 upstream.

1. The idProduct is little endian, so make sure its value to be
compatible with the current CPU. Make no break on big endian processors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 04753523 upstream.

The module alias should be "ehci-omap" and not
"omap-ehci" to match the platform device name.
The omap-ehci module should now autoload correctly.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1f3f6877 upstream.

The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.

The CDC ACM class driver cannot support functions with only 2
endpoints.  The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.

There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>