Adds the register definitions and code to read the time
register.
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instructions for time stamping outgoing packets are take from the
socket layer and later copied into the new skb.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The overlap with the old SO_TIMESTAMP[NS] options is handled so
that time stamping in software (net_enable_timestamp()) is
enabled when SO_TIMESTAMP[NS] and/or SO_TIMESTAMPING_RX_SOFTWARE
is set.  It's disabled if all of these are off.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The additional per-packet information (16 bytes for time stamps, 1
byte for flags) is stored for all packets in the skb_shared_info
struct. This implementation detail is hidden from users of that
information via skb_* accessor functions. A separate struct resp.
union is used for the additional information so that it can be
stored/copied easily outside of skb_shared_info.

Compared to previous implementations (reusing the tstamp field
depending on the context, optional additional structures) this
is the simplest solution. It does not extend sk_buff itself.

TX time stamping is implemented in software if the device driver
doesn't support hardware time stamping.

The new semantic for hardware/software time stamping around
ndo_start_xmit() is based on two assumptions about existing
network device drivers which don't support hardware time
stamping and know nothing about it:
 - they leave the new skb_shared_tx unmodified
 - the keep the connection to the originating socket in skb->sk
   alive, i.e., don't call skb_orphan()

Given that skb_shared_tx is new, the first assumption is safe.
The second is only true for some drivers. As a result, software
TX time stamping currently works with the bnx2 driver, but not
with the unmodified igb driver (the two drivers this patch series
was tested with).
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.

When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.

The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mapping from a struct timecounter to a time returned by functions like
ktime_get_real() is implemented. This is sufficient to use this code
in a network device driver which wants to support hardware time
stamping and transformation of hardware time stamps to system time.

The interface could have been made more versatile by not depending on
a time counter, but this wasn't done to avoid writing glue code
elsewhere.

The method implemented here is the one used and analyzed under the name
"assisted PTP" in the LCI PTP paper:
http://www.linuxclustersinstitute.org/conferences/archive/2008/PDF/Ohly_92221.pdfAcked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far struct clocksource acted as the interface between time/timekeeping.c
and hardware. This patch generalizes the concept so that a similar
interface can also be used in other contexts. For that it introduces
new structures and related functions *without* touching the existing
struct clocksource.

The reasons for adding these new structures to clocksource.[ch] are
* the APIs are clearly related
* struct clocksource could be cleaned up to use the new structs
* avoids proliferation of files with similar names (timesource.h?
  timecounter.h?)

As outlined in the discussion with John Stultz, this patch adds
* struct cyclecounter: stateless API to hardware which counts clock cycles
* struct timecounter: stateful utility code built on a cyclecounter which
  provides a nanosecond counter
* only the function to read the nanosecond counter; deltas are used internally
  and not exposed to users of timecounter

The code does no locking of the shared state. It must be called at least
as often as the cycle counter wraps around to detect these wrap arounds.
Both is the responsibility of the timecounter user.
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single-thread access must be ensured for ICH8 NVM and PHY operations.
This synchronization is provided by the nvm_mutex. To assist in
understanding the contexts from which this code could be reached,
a WARN was output if the mutex was not going to be immediately
acquirable (if !mutex_trylock()). The code has now been optimized,
and we have verified that the few remaining mutex contentions are
reasonable and non-blocking, and it is time to remove the
mutex_trylock() and WARN messages.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn.c
	drivers/net/wireless/iwlwifi/iwl3945-base.c

Base versions handle constant folding now.  For headers exposed to
userspace, we must only expose the __ prefixed versions.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use cpu_to_le32 directly as it handles constant folding now, replace direct
uses of __constant_cpu_to_{endian} as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When forward-porting the tun accounting patch I managed to break
the send path compltely by dropping the tun_get call.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need the udelay() for all families, including AR5416.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is used for ASPM.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The test to find out if we have FAT channels do not consider that
the value of regulatory_bands for the 5000 series is larger than its
eeprom size. Using the eeprom size is strange in itself.

Use a new EEPROM_REGULATORY_BAND_NO_FAT to indicate no FAT support
and test for that explicitly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch remove w/a used for development boards.
These boards are not available thus no need to keep it inside driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch replaces where possible usage of pci register
defined in the driver by ones defined in pci_regs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It appears that you can completely mess up mac80211 in IBSS
mode by sending it a disassoc or deauth: it'll stop queues
and do a lot more but not ever do anything again. Fix this
by not handling all those frames in IBSS mode,
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The code beyond this point is supposed to be used for
non-IBSS (managed) mode only.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Just to make wext.c more self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove all the code from mac80211 to keep track of BSSes
and use the cfg80211-provided code completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a more flexible BSS lookup function so that mac80211 or
other drivers can actually use this for getting the BSS to
connect to.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch introduces cfg80211_unlink_bss, a function to
allow a driver to remove a BSS from the internal list and
make it not show up in scan results any more -- this is
to be used when the driver detects that the BSS is no
longer available.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When cfg80211 users have their own allocated data in the per-BSS
private data, they will need to free this when the BSS struct is
destroyed. Add a free_priv method and fix one place where the BSS
was kfree'd rather than released properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's no need to create a BSS struct only to pass it to
ieee80211_sta_join_ibss, so refactor this function into
__ieee80211_sta_join_ibss which takes all the relevant
paramters, and ieee80211_sta_join_ibss which takes a BSS
struct (used when joining an IBSS that already has other
members).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Essentially consisting of passing the sta_info pointer around,
instead of repeatedly doing hash lookups.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Clean up the locking by splitting it into two functions,
this will also enable further cleanups of stopping all
sessions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The sta_info pointer can very well be passed to
ieee80211_sta_tear_down_BA_sessions, this will
later allow us to pass it through even further.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As far as I can tell, there are possible lockups because both the RX
session_timer and TX addba_resp_timer are del_timer_sync'ed under
the sta spinlock which both timer functions take. Additionally, the
TX agg code seems to leak memory when TX aggregation is not disabled
before the sta_info is freed.

Fix this by making the free code a little smarter in the RX agg case,
and actually make the sta_info_destroy code free the TX agg info in
the TX agg case. We won't notify the peer, but it'll notice something
is wrong anyway, and normally this only happens after we've told it
in some other way we will no longer talk to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When disabling TX aggregation because it was rejected or from
the timer (it was not accepted), there is a window where we
first set the state to operation, unlock, and then undo the
whole thing. Avoid that by splitting up the stop function.
Also get rid of the pointless sta_info indirection in the timer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add documentation and move ieee80211_start_tx_ba_cb_irqsafe to right
after ieee80211_start_tx_ba_cb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Doing so would be an MLME protocol violation when the peer disabled
the aggregation session. Quick driver review indicates that there are
error codes passed all over the drivers but cannot ever be nonzero
except in error conditions that would indicate mac80211 bugs.

No real changes here, since no drivers currently can return -EBUSY.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We can only support aggregation on AP/STA right now. HT isn't defined
for IBSS, WDS or MESH. In the WDS/MESH cases it's not clear what to
put into the IBSS field, and we don't handle that in the code at all.
Also fix the code to handle VLAN correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Create two new files, agg-tx.c and agg-rx.c to make it clearer
which code is common (ht.c) and which is specific (agg-*.c).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The values are in TUs (1.024ms), not ms.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>