Pull networking fixes from Paolo Abeni:
 "Including fixes from bpf and netfilter.

  Current release - regressions:

   - netfilter: cttimeout: fix slab-out-of-bounds read in
     cttimeout_net_exit

Current release - new code bugs:

   - bpf: ftrace: keep address offset in ftrace_lookup_symbols

   - bpf: force cookies array to follow symbols sorting

  Previous releases - regressions:

   - ipv4: ping: fix bind address validity check

   - tipc: fix use-after-free read in tipc_named_reinit

   - eth: veth: add updating of trans_start

  Previous releases - always broken:

   - sock: redo the psock vs ULP protection check

   - netfilter: nf_dup_netdev: fix skb_under_panic

   - bpf: fix request_sock leak in sk lookup helpers

   - eth: igb: fix a use-after-free issue in igb_clean_tx_ring

   - eth: ice: prohibit improper channel config for DCB

   - eth: at803x: fix null pointer dereference on AR9331 phy

   - eth: virtio_net: fix xdp_rxq_info bug after suspend/resume

  Misc:

   - eth: hinic: replace memcpy() with direct assignment"

* tag 'net-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
  net: openvswitch: fix parsing of nw_proto for IPv6 fragments
  sock: redo the psock vs ULP protection check
  Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
  virtio_net: fix xdp_rxq_info bug after suspend/resume
  igb: Make DMA faster when CPU is active on the PCIe link
  net: dsa: qca8k: reduce mgmt ethernet timeout
  net: dsa: qca8k: reset cpu port on MTU change
  MAINTAINERS: Add a maintainer for OCP Time Card
  hinic: Replace memcpy() with direct assignment
  Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c"
  net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
  ice: ethtool: Prohibit improper channel config for DCB
  ice: ethtool: advertise 1000M speeds properly
  ice: Fix switchdev rules book keeping
  ice: ignore protocol field in GTP offload
  netfilter: nf_dup_netdev: add and use recursion counter
  netfilter: nf_dup_netdev: do not push mac header a second time
  selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
  net/tls: fix tls_sk_proto_close executed repeatedly
  erspan: do not assume transport header is always set
  ...

Pull MMC fixes from Ulf Hansson:

 - mtk-sd: Fix dma hang issues

 - sdhci-pci-o2micro: Fix card detect by dealing with debouncing

* tag 'mmc-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: mediatek: wait dma stop bit reset to 0
  mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing

Pull sound fixes from Takashi Iwai:
 "All small changes, mostly device-specific:

   - A regression fix for PCM WC-page allocation on x86

   - A regression fix for i915 audio component binding

   - Fixes for (longstanding) beep handling bug

   - Runtime PM fixes for Intel LPE HDMI audio

   - A couple of pending FireWire fixes

   - Usual HD-audio and USB-audio quirks, new Intel dspconf entries"

* tag 'sound-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek: Add quirk for Clevo NS50PU
  ALSA: hda: Fix discovery of i915 graphics PCI device
  ALSA: hda/via: Fix missing beep setup
  ALSA: hda/conexant: Fix missing beep setup
  ALSA: memalloc: Drop x86-specific hack for WC allocations
  ALSA: hda/realtek: Add quirk for Clevo PD70PNT
  ALSA: x86: intel_hdmi_audio: use pm_runtime_resume_and_get()
  ALSA: x86: intel_hdmi_audio: enable pm_runtime and set autosuspend delay
  ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
  ALSA: hda: intel-dspcfg: use SOF for UpExtreme and UpExtreme11 boards
  firewire: convert sysfs sprintf/snprintf family to sysfs_emit
  firewire: cdev: fix potential leak of kernel stack due to uninitialized value
  ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
  ALSA: hda/realtek - ALC897 headset MIC no sound
  ALSA: usb-audio: US16x08: Move overflow check before array access
  ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop

When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.

As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.

This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.

The offending commit is partially reverted to restore the expected
behavior.

The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.

Cc: stable@vger.kernel.org
Fixes: fa642f08 ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragmentsSigned-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to
the new tcp_bpf_update_proto() function. I'm guessing that this
was done to allow creating psocks for non-inet sockets.

Unfortunately the destruction path for psock includes the ULP
unwind, so we need to fail the sk_psock_init() itself.
Otherwise if ULP is already present we'll notice that later,
and call tcp_update_ulp() with the sk_proto of the ULP
itself, which will most likely result in the ULP looping
its callbacks.

Fixes: 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-2-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 69135c57.

This commit was just papering over the issue, ULP should not
get ->update() called with its own sk_prot. Each ULP would
need to add this check.

Fixes: 69135c57 ("net/tls: fix tls_sk_proto_close executed repeatedly")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-1-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The following sequence currently causes a driver bug warning
when using virtio_net:

  # ip link set eth0 up
  # echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
  <resume>
  # ip link set eth0 down

  Missing register, driver bug
  WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
  Call trace:
   xdp_rxq_info_unreg+0x58/0x60
   virtnet_close+0x58/0xac
   __dev_close_many+0xac/0x140
   __dev_change_flags+0xd8/0x210
   dev_change_flags+0x24/0x64
   do_setlink+0x230/0xdd0
   ...

This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().

Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.

Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.

Fixes: 754b8a21 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-06-21

This series contains updates to ice driver only.

Marcin fixes GTP filters by allowing ignoring of the inner ethertype field.

Wojciech adds VSI handle tracking in order to properly distinguish similar
filters for removal.

Anatolii removes ability to set 1000baseT and 1000baseX fields
concurrently which caused link issues. He also disallows setting
channels to less than the number of Traffic Classes which would cause
NULL pointer dereference.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  ice: ethtool: Prohibit improper channel config for DCB
  ice: ethtool: advertise 1000M speeds properly
  ice: Fix switchdev rules book keeping
  ice: ignore protocol field in GTP offload
====================

Link: https://lore.kernel.org/r/20220621224756.631765-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.

According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.

In addition to that, commit b6e0c419 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.

Fixes: b6e0c419 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.

Fixes: 5950c7c0 ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.

To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.

Fixes: f58d2598 ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

I've been contributing and reviewing patches for ptp_ocp driver for
some time and I'm taking care of it's github mirror. On Jakub's
suggestion, I would like to step forward and become a maintainer for
this driver. This patch adds a dedicated entry to MAINTAINERS.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220621233131.21240-1-vfedorenko@novek.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-kselftest-fixes-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:
 "Compile time fixes and run-time resources leaks:

   - Fix clang cross compilation

   - Fix resource leak when return error

   - fix compile error for dma_map_benchmark

   - Fix regression - make use of GUP_TEST_FILE macro"

* tag 'linux-kselftest-fixes-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: make use of GUP_TEST_FILE macro
  selftests: vm: Fix resource leak when return error
  selftests dma: fix compile error for dma_map_benchmark
  selftests: Fix clang cross compilation

Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.

Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.

[This is a duplicate of commit 2c0ab32b ("hinic: Replace memcpy()
 with direct assignment") which was applied to net-next.]

Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes headset detection on Clevo NS50PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220622150017.9897-1-tcrawford@system76.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Pull 9pfs fixes from Dominique Martinet:
 "A couple of fid refcount and fscache fixes:

   - fid refcounting was incorrect in some corner cases and would leak
     resources, only freed at umount time. The first three commits fix
     three such cases

   - 'cache=loose' or fscache was broken when trying to write a partial
     page to a file with no read permission since the rework a few
     releases ago.

     The fix taken here is just to restore old behavior of using the
     special 'writeback_fid' for such reads, which is open as root/RDWR
     and such not get complains that we try to read on a WRONLY fid.

     Long-term it'd be nice to get rid of this and not issue the read at
     all (skip cache?) in such cases, but that direction hasn't
     progressed"

* tag '9p-for-5.19-rc4' of https://github.com/martinetd/linux:
  9p: fix EBADF errors in cached mode
  9p: Fix refcounting during full path walks for fid lookups
  9p: fix fid refcount leak in v9fs_vfs_get_link
  9p: fix fid refcount leak in v9fs_vfs_atomic_open_dotl

This reverts commit 8fc74d18.

BAR0 is the main (only?) register bank for this device. We most
obviously can't unmap it before the netdev is unregistered.
This was pointed out in review but the patch got reposted and
merged, anyway.

The author of the patch was only testing it with a QEMU model,
which I presume does not emulate enough for the netdev to be brought
up (author's replies are not visible in lore because they kept sending
their emails in HTML).

Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/
Fixes: 8fc74d18 ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Use get_random_u32() instead of prandom_u32_state() in nft_meta
   and nft_numgen, from Florian Westphal.

2) Incorrect list head in nfnetlink_cttimeout in recent update coming
   from previous development cycle. Also from Florian.

3) Incorrect path to pktgen scripts for nft_concat_range.sh selftest.
   From Jie2x Zhou.

4) Two fixes for the for nft_fwd and nft_dup egress support, from Florian.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nf_dup_netdev: add and use recursion counter
  netfilter: nf_dup_netdev: do not push mac header a second time
  selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
  netfilter: cttimeout: fix slab-out-of-bounds read typo in cttimeout_net_exit
  netfilter: use get_random_u32 instead of prandom
====================

Link: https://lore.kernel.org/r/20220621085618.3975-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simon reports that if two LAN9514 USB adapters are directly connected
without an intermediate switch, the link fails to come up and link LEDs
remain dark.  The issue was introduced by commit 1ce8b372 ("usbnet:
smsc95xx: Forward PHY interrupts to PHY driver to avoid polling").

The PHY suffers from a known erratum wherein link detection becomes
unreliable if Energy Detect Power-Down is used.  In poll mode, the
driver works around the erratum by briefly disabling EDPD for 640 msec
to detect a neighbor, then re-enabling it to save power.

In interrupt mode, no interrupt is signaled if EDPD is used by both link
partners, so it must not be enabled at all.

We'll recoup the power savings by enabling SUSPEND1 mode on affected
LAN95xx chips in a forthcoming commit.

Fixes: 1ce8b372 ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Do not allow setting less channels, than Traffic Classes there are
via ethtool. There must be at least one channel per Traffic Class.

If you set less channels, than Traffic Classes there are, then during
ice_vsi_rebuild there would be allocated only the requested amount
of tx/rx rings in ice_vsi_alloc_arrays. But later in ice_vsi_setup_q_map
there would be requested at least one channel per Traffic Class. This
results in setting num_rxq > alloc_rxq and num_txq > alloc_txq.
Later, there would be a NULL pointer dereference in
ice_vsi_map_rings_to_vectors, because we go beyond of rx_rings or
tx_rings arrays.

Change ice_set_channels() to return error if you try to allocate less
channels, than Traffic Classes there are.
Change ice_vsi_setup_q_map() and ice_vsi_setup_q_map_mqprio() to return
status code instead of void.
Add error handling for ice_vsi_setup_q_map() and
ice_vsi_setup_q_map_mqprio() in ice_vsi_init() and ice_vsi_cfg_tc().

[53753.889983] INFO: Flow control is disabled for this traffic class (0) on this vsi.
[53763.984862] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
[53763.992915] PGD 14b45f5067 P4D 0
[53763.996444] Oops: 0002 [#1] SMP NOPTI
[53764.000312] CPU: 12 PID: 30661 Comm: ethtool Kdump: loaded Tainted: GOE    --------- -  - 4.18.0-240.el8.x86_64 #1
[53764.011825] Hardware name: Intel Corporation WilsonCity/WilsonCity, BIOS WLYDCRB1.SYS.0020.P21.2012150710 12/15/2020
[53764.022584] RIP: 0010:ice_vsi_map_rings_to_vectors+0x7e/0x120 [ice]
[53764.029089] Code: 41 0d 0f b7 b7 12 05 00 00 0f b6 d0 44 29 de 44 0f b7 c6 44 01 c2 41 39 d0 7d 2d 4c 8b 47 28 44 0f b7 ce 83 c6 01 4f 8b 04 c8 <49> 89 48 28 4                           c 8b 89 b8 01 00 00 4d 89 08 4c 89 81 b8 01 00 00 44
[53764.048379] RSP: 0018:ff550dd88ea47b20 EFLAGS: 00010206
[53764.053884] RAX: 0000000000000002 RBX: 0000000000000004 RCX: ff385ea42fa4a018
[53764.061301] RDX: 0000000000000006 RSI: 0000000000000005 RDI: ff385e9baeedd018
[53764.068717] RBP: 0000000000000010 R08: 0000000000000000 R09: 0000000000000004
[53764.076133] R10: 0000000000000002 R11: 0000000000000004 R12: 0000000000000000
[53764.083553] R13: 0000000000000000 R14: ff385e658fdd9000 R15: ff385e9baeedd018
[53764.090976] FS:  000014872c5b5740(0000) GS:ff385e847f100000(0000) knlGS:0000000000000000
[53764.099362] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[53764.105409] CR2: 0000000000000028 CR3: 0000000a820fa002 CR4: 0000000000761ee0
[53764.112851] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[53764.120301] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[53764.127747] PKRU: 55555554
[53764.130781] Call Trace:
[53764.133564]  ice_vsi_rebuild+0x611/0x870 [ice]
[53764.138341]  ice_vsi_recfg_qs+0x94/0x100 [ice]
[53764.143116]  ice_set_channels+0x1a8/0x3e0 [ice]
[53764.147975]  ethtool_set_channels+0x14e/0x240
[53764.152667]  dev_ethtool+0xd74/0x2a10
[53764.156665]  ? __mod_lruvec_state+0x44/0x110
[53764.161280]  ? __mod_lruvec_state+0x44/0x110
[53764.165893]  ? page_add_file_rmap+0x15/0x170
[53764.170518]  ? inet_ioctl+0xd1/0x220
[53764.174445]  ? netdev_run_todo+0x5e/0x290
[53764.178808]  dev_ioctl+0xb5/0x550
[53764.182485]  sock_do_ioctl+0xa0/0x140
[53764.186512]  sock_ioctl+0x1a8/0x300
[53764.190367]  ? selinux_file_ioctl+0x161/0x200
[53764.195090]  do_vfs_ioctl+0xa4/0x640
[53764.199035]  ksys_ioctl+0x60/0x90
[53764.202722]  __x64_sys_ioctl+0x16/0x20
[53764.206845]  do_syscall_64+0x5b/0x1a0
[53764.210887]  entry_SYSCALL_64_after_hwframe+0x65/0xca

Fixes: 87324e74 ("ice: Implement ethtool ops for channels")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.

Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.

Fixes: 48cb27f2 ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Adding two filters with same matching criteria ends up with
one rule in hardware with act = ICE_FWD_TO_VSI_LIST.
In order to remove them properly we have to keep the
information about vsi handle which is used in VSI bitmap
(ice_adv_fltr_mgmt_list_entry::vsi_list_info::vsi_map).

Fixes: 0d08a441 ("ice: ndo_setup_tc implementation for PF")
Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Commit 34a89775 ("ice: Add support for inner etype in switchdev")
added the ability to match on inner ethertype. A side effect of that change
is that it is now impossible to add some filters for protocols which do not
contain inner ethtype field. tc requires the protocol field to be specified
when providing certain other options, e.g. src_ip. This is a problem in
case of GTP - when user wants to specify e.g. src_ip, they also need to
specify protocol in tc command (otherwise tc fails with: Illegal "src_ip").
Because GTP is a tunnel, the protocol field is treated as inner protocol.
GTP does not contain inner ethtype field and the filter cannot be added.

To fix this, ignore the ethertype field in case of GTP filters.

Fixes: 9a225f81 ("ice: Support GTP-U and GTP-C offload in switchdev")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Pull EFI fixes from Ard Biesheuvel:

 - remove pointless include of asm/efi.h, which does not exist on ia64

 - fix DXE service marshalling prototype for mixed mode

* tag 'efi-urgent-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi/x86: libstub: Fix typo in __efi64_argmap* name
  efi: sysfb_efi: remove unnecessary <asm/efi.h> include

Pull signature checking selftest from David Howells:
 "The signature checking code, as used by module signing, kexec, etc.,
  is non-FIPS compliant as there is no selftest.

  For a kernel to be FIPS-compliant, signature checking would have to be
  tested before being used, and the box would need to panic if it's not
  available (probably reasonable as simply disabling signature checking
  would prevent you from loading any driver modules).

  Deal with this by adding a minimal test.

  This is split into two patches: the first moves load_certificate_list()
  to the same place as the X.509 code to make it more accessible
  internally; the second adds a selftest"

* tag 'certs-20220621' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  certs: Add FIPS selftests
  certs: Move load_certificate_list() to be with the asymmetric keys code

Pull btrfs fixes from David Sterba:

 - print more error messages for invalid mount option values

 - prevent remount with v1 space cache for subpage filesystem

 - fix hang during unmount when block group reclaim task is running

* tag 'for-5.19-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: add error messages to all unrecognized mount options
  btrfs: prevent remounting to v1 space cache for subpage mount
  btrfs: fix hang during unmount when block group reclaim task is running

The recent patch to make afs_getattr consult the server didn't account
for the pseudo-inodes employed by the dynamic root-type afs superblock
not having a volume or a server to access, and thus an oops occurs if
such a directory is stat'd.

Fix this by checking to see if the vnode->volume pointer actually points
anywhere before following it in afs_getattr().

This can be tested by stat'ing a directory in /afs.  It may be
sufficient just to do "ls /afs" and the oops looks something like:

        BUG: kernel NULL pointer dereference, address: 0000000000000020
        ...
        RIP: 0010:afs_getattr+0x8b/0x14b
        ...
        Call Trace:
         <TASK>
         vfs_statx+0x79/0xf5
         vfs_fstatat+0x49/0x62

Fixes: 2aeb8c86 ("afs: Fix afs_getattr() to refetch file status if callback break occurred")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/165408450783.1031787.7941404776393751186.stgit@warthog.procyon.org.uk/Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The actual name of the DXE services function used
is set_memory_space_attributes(), not set_memory_space_descriptor().

Change EFI mixed mode helper macro name to match the function name.

Fixes: 31f1a0ed ("efi/x86: libstub: Make DXE calls mixed mode safe")
Signed-off-by: Evgeniy Baskov <baskov@ispras.ru>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

Nothing defined in the header is used by drivers/firmware/efi/sysfb_efi.c
but also, including it can lead to build errors when built on arches that
don't have an asm/efi.h header file.

This can happen for example if a driver that is built when COMPILE_TEST is
enabled selects the SYSFB symbol, e.g. on powerpc with allyesconfig:

drivers/firmware/efi/sysfb_efi.c:29:10: fatal error: asm/efi.h: No such file or directory
   29 | #include <asm/efi.h>
      |          ^~~~~~~~~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

Add some selftests for signature checking when FIPS mode is enabled.  These
need to be done before we start actually using the signature checking for
things and must panic the kernel upon failure.

Note that the tests must not check the blacklist lest this provide a way to
prevent a kernel from booting by installing a hash of a test key in the
appropriate UEFI table.
Reported-by: Simo Sorce <simo@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Simo Sorce <simo@redhat.com>
Reviewed-by: Herbert Xu <herbert@gondor.apana.org.au>
cc: keyrings@vger.kernel.org
cc: linux-crypto@vger.kernel.org
Link: https://lore.kernel.org/r/165515742832.1554877.2073456606206090838.stgit@warthog.procyon.org.uk/

Move load_certificate_list(), which loads a series of binary X.509
certificates from a blob and inserts them as keys into a keyring, to be
with the asymmetric keys code that it drives.

This makes it easier to add FIPS selftest code in which we need to load up
a private keyring for the tests to use.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Simo Sorce <simo@redhat.com>
Reviewed-by: Herbert Xu <herbert@gondor.apana.org.au>
cc: keyrings@vger.kernel.org
cc: linux-crypto@vger.kernel.org
Link: https://lore.kernel.org/r/165515742145.1554877.13488098107542537203.stgit@warthog.procyon.org.uk/

It's been reported that the recent fix for skipping the
component-binding with D-GPU caused a regression on some systems; it
resulted in the completely missing component binding with i915 GPU.

The problem was the use of pci_get_class() function.  It matches with
the full PCI class bits, while we want to match only partially the PCI
base class bits.  So, when a system has an i915 graphics device with
the PCI class 0380, it won't hit because we're looking for only the
PCI class 0300.

This patch fixes i915_gfx_present() to look up each PCI device and
match with PCI base class explicitly instead of pci_get_class().

Fixes: c9db8a30 ("ALSA: hda/i915 - skip acomp init if no matching display")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Tested-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1200611
Link: https://lore.kernel.org/r/87bkunztec.wl-tiwai@suse.de
Link: https://lore.kernel.org/r/20220621120044.11573-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Now that the egress function can be called from egress hook, we need
to avoid recursive calls into the nf_tables traverser, else crash.

Fixes: f87b9464 ("netfilter: nft_fwd_netdev: Support egress hook")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Eric reports skb_under_panic when using dup/fwd via bond+egress hook.
Before pushing mac header, we should make sure that we're called from
ingress to put back what was pulled earlier.

In egress case, the MAC header is already there; we should leave skb
alone.

While at it be more careful here: skb might have been altered and
headroom reduced, so add a skb_cow() before so that headroom is
increased if necessary.

nf_do_netdev_egress() assumes skb ownership (it normally ends with
a call to dev_queue_xmit), so we must free the packet on error.

Fixes: f87b9464 ("netfilter: nft_fwd_netdev: Support egress hook")
Reported-by: Eric Garver <eric@garver.life>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Before change:
make -C netfilter
 TEST: performance
   net,port                                                      [SKIP]
   perf not supported
   port,net                                                      [SKIP]
   perf not supported
   net6,port                                                     [SKIP]
   perf not supported
   port,proto                                                    [SKIP]
   perf not supported
   net6,port,mac                                                 [SKIP]
   perf not supported
   net6,port,mac,proto                                           [SKIP]
   perf not supported
   net,mac                                                       [SKIP]
   perf not supported

After change:
   net,mac                                                       [ OK ]
     baseline (drop from netdev hook):               2061098pps
     baseline hash (non-ranged entries):             1606741pps
     baseline rbtree (match on first field only):    1191607pps
     set with  1000 full, ranged entries:            1639119pps
ok 8 selftests: netfilter: nft_concat_range.sh

Fixes: 611973c1 ("selftests: netfilter: Introduce tests for sets with range concatenation")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jie2x Zhou <jie2x.zhou@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull SCSI fixes from James Bottomley:
 "Eight fixes, all in drivers (ufs, scsi_debug, storvsc, iscsi, ibmvfc).

  Apart from the ufs command clearing updates, these are mostly minor
  and obvious fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ibmvfc: Store vhost pointer during subcrq allocation
  scsi: ibmvfc: Allocate/free queue resource only during probe/remove
  scsi: storvsc: Correct reporting of Hyper-V I/O size limits
  scsi: ufs: Fix a race between the interrupt handler and the reset handler
  scsi: ufs: Support clearing multiple commands at once
  scsi: ufs: Simplify ufshcd_clear_cmd()
  scsi: iscsi: Exclude zero from the endpoint ID range
  scsi: scsi_debug: Fix zone transition to full condition

Merge tag 'perf-tools-fixes-for-v5.19-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tool fixes from Arnaldo Carvalho de Melo:

 - Don't set data source if it's not a memory operation in ARM SPE
   (Statistical Profiling Extensions).

 - Fix handling of exponent floating point values in perf stat
   expressions.

 - Don't leak fd on failure on libperf open.

 - Fix 'perf test' CPU topology test for PPC guest systems.

 - Fix undefined behaviour on breakpoint account 'perf test' entry.

 - Record only user callchains on the "Check ARM64 callgraphs are
   complete in FP mode" 'perf test' entry.

 - Fix "perf stat CSV output linter" test on s390.

 - Sync batch of kernel headers with tools/perf/.

* tag 'perf-tools-fixes-for-v5.19-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  tools headers UAPI: Sync linux/prctl.h with the kernel sources
  perf metrics: Ensure at least 1 id per metric
  tools headers arm64: Sync arm64's cputype.h with the kernel sources
  tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
  perf arm-spe: Don't set data source if it's not a memory operation
  perf expr: Allow exponents on floating point values
  perf test topology: Use !strncmp(right platform) to fix guest PPC comparision check
  perf test: Record only user callchains on the "Check Arm64 callgraphs are complete in fp mode" test
  perf beauty: Update copy of linux/socket.h with the kernel sources
  perf test: Fix variable length array undefined behavior in bp_account
  libperf evsel: Open shouldn't leak fd on failure
  perf test: Fix "perf stat CSV output linter" test on s390
  perf unwind: Fix uninitialized variable

Pull slab fixes from Vlastimil Babka:

 - A slub fix for PREEMPT_RT locking semantics from Sebastian.

 - A slub fix for state corruption due to a possible race scenario from
   Jann.

* tag 'slab-for-5.19-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
  mm/slub: add missing TID updates on slab deactivation
  mm/slub: Move the stackdepot related allocation out of IRQ-off section.

Check vm_fault->pgoff before using it.  When we removed the warning, we
also removed the check.

Fixes: 7b26e4e2 ("udmabuf: drop WARN_ON() check.")
Reported-by: zdi-disclosures@trendmicro.com
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Like the previous fix for Conexant codec, the beep_nid has to be set
up before calling snd_hda_gen_parse_auto_config(); otherwise it'd miss
the path setup.

Fix the call order for addressing the missing beep setup.

Fixes: 0e8f9862 ("ALSA: hda/via - Simplify control management")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216152
Link: https://lore.kernel.org/r/20220620104008.1994-2-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>